Diese Website existiert nur weil wir Werbung mit AdSense ausliefern.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.

System hängt sich auf beim Audio-Cd auslesen

Alles rund um das Thema Multimedia unter Linux

Moderator: Moderatoren

Antworten
Gandalf333
Hacker
Hacker
Beiträge: 487
Registriert: 26. Sep 2006, 07:10

System hängt sich auf beim Audio-Cd auslesen

Beitrag von Gandalf333 »

AMD Athlon(tm) XP 2200+
Suse 11.0
Linux 2.6.25.11-0.1-default i686
KDE: 3.5.9 "release 49.1"

Ich will meine Audio-Cds auch auf meinem MP3-Player hören und dazu habe ich versucht sie mittels K3b digital auszulesen.
Leider hängt sich während das Auslesens immerwieder das gesamte System auf, d.h. die Maus lässt sich nicht mehr bedienen und auch sonst kein Befehl mehr ausführen.

Code: Alles auswählen

k3b found invalid bcd values. No bcd tox
/dev/sr0:setting last sector of last track to 249406
War das letzte was ich auf der Konsole lesen konnte.
spoensche
Moderator
Moderator
Beiträge: 7587
Registriert: 30. Okt 2004, 23:53
Wohnort: Siegen

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von spoensche »

Die CD, wird aber beim einlegen erkannt und gemountet? (Bevor du irgendwas mit K3B machst) Kannst du die CD abspielen oder wird da auch gestreikt? Laut der Fehlermeldung könnte ein Sektor kaputt sein. Ist es eine gebrannte CD oder eine originale?
Gandalf333
Hacker
Hacker
Beiträge: 487
Registriert: 26. Sep 2006, 07:10

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von Gandalf333 »

CD wird gemountet.

Ich habe jetzt 2 unterschiedliche Audio-CDs getestet.
gropiuskalle
Guru
Guru
Beiträge: 4603
Registriert: 20. Nov 2007, 15:17
Wohnort: Berlin
Kontaktdaten:

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von gropiuskalle »

CD wird gemountet.
Geht eigentlich gar nicht. Lass die vor dem Einlesen bzw. Abspielen mal ungemountet.
Gandalf333
Hacker
Hacker
Beiträge: 487
Registriert: 26. Sep 2006, 07:10

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von Gandalf333 »

Und wie mach ich das?
gropiuskalle
Guru
Guru
Beiträge: 4603
Registriert: 20. Nov 2007, 15:17
Wohnort: Berlin
Kontaktdaten:

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von gropiuskalle »

Eine Audio-CD sollte eigentlich (wie eine Video-DVD und im Gegensatz zu Daten-DVDs und CDs) eben nicht automatisch gemountet werden, komisch, dass das bei Dir offenbar doch geschieht.

Rechtsklick auf das jeweilige Medium und "Laufwerkeinbindung lösen" sollte klappen.
Gandalf333
Hacker
Hacker
Beiträge: 487
Registriert: 26. Sep 2006, 07:10

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von Gandalf333 »

Unter kde 4.1 klappt es bei der audio-cd ohne zu mmounten. (finde ich persönlich nicht gut, weil mir bisher immer angeboten wurde, mit welcher Anwendung ich die CD öffnen will?).

Trotz allem, klappt es das Auslesen der Cd nicht und während des Vorgangs friert das System ein.
Gandalf333
Hacker
Hacker
Beiträge: 487
Registriert: 26. Sep 2006, 07:10

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von Gandalf333 »

Hallo das Problem mit dem Aufhängen bzw. Einfrieren des Systems habe ich immernoch beim Auslesen von Audio Cds und auch wenn Firefox läuft.
Da geht dann gar nichts mehr. Ich muss also den PC aus und wieder einschalten.

Mit der Bitte um Hilfe!

Code: Alles auswählen

/var/log/boot.msg

Inspecting /boot/System.map-2.6.25.18-0.2-pae
Loaded 28188 symbols from /boot/System.map-2.6.25.18-0.2-pae.
Symbols match kernel version 2.6.25.
No module symbols loaded - kernel modules not enabled.

klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.25.18-0.2-pae (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-10-21 16:30:26 +0200
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
<4> BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
<4> BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
<4> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<5>1150MB HIGHMEM available.
<5>896MB LOWMEM available.
<6>Scan SMP from c0000000 for 1024 bytes.
<6>Scan SMP from c009fc00 for 1024 bytes.
<6>Scan SMP from c00f0000 for 65536 bytes.
<6>found SMP MP-table at [c00f5ec0] 000f5ec0
<7>Entering add_active_range(0, 0, 524016) 0 entries of 256 used
<4>Zone PFN ranges:
<4>  DMA             0 ->     4096
<4>  Normal       4096 ->   229376
<4>  HighMem    229376 ->   524016
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4>    0:        0 ->   524016
<7>On node 0 totalpages: 524016
<7>  DMA zone: 32 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 4064 pages, LIFO batch:0
<7>  Normal zone: 1760 pages used for memmap
<7>  Normal zone: 223520 pages, LIFO batch:31
<7>  HighMem zone: 2301 pages used for memmap
<7>  HighMem zone: 292339 pages, LIFO batch:31
<7>  Movable zone: 0 pages used for memmap
<6>DMI 2.2 present.
<6>Using APIC driver default
<4>ACPI: RSDP 000F78B0, 0014 (r0 KT600 )
<4>ACPI: RSDT 7FEF3000, 002C (r1 KT600  AWRDACPI 42302E31 AWRD        0)
<4>ACPI: FACP 7FEF3040, 0074 (r1 KT600  AWRDACPI 42302E31 AWRD        0)
<4>ACPI: DSDT 7FEF30C0, 4908 (r1 KT600  AWRDACPI     1000 MSFT  100000E)
<4>ACPI: FACS 7FEF0000, 0040
<4>ACPI: APIC 7FEF7A00, 005A (r1 KT600  AWRDACPI 42302E31 AWRD        0)
<6>ACPI: PM-Timer IO Port: 0x4008
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>Processor #0 6:8 APIC version 16
<6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
<7>ACPI: IRQ0 used by override.
<7>ACPI: IRQ2 used by override.
<7>ACPI: IRQ9 used by override.
<4>Enabling APIC mode:  Flat.  Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<4>Allocating PCI resources starting at 80000000 (gap: 7ff00000:7ed00000)
<6>PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
<6>PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519923
<5>Kernel command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 resume=/dev/sda5 splash=silent vga=0x31a
<6>bootsplash: silent mode.
<7>mapped APIC to ffffb000 (fee00000)
<7>mapped IOAPIC to ffffa000 (fec00000)
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 16384 bytes)
<4>Detected 1827.881 MHz processor.
<4>Console: colour dummy device 80x25
<6>console [tty0] enabled
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 2067708k/2096064k available (1954k kernel code, 27108k reserved, 1679k data, 264k init, 1178560k highmem)
<6>virtual kernel memory layout:
<4>    fixmap  : 0xff8b2000 - 0xfffff000   (7476 kB)
<4>    pkmap   : 0xff400000 - 0xff600000   (2048 kB)
<4>    vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
<4>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
<4>      .init : 0xc0495000 - 0xc04d7000   ( 264 kB)
<4>      .data : 0xc02e8aea - 0xc048c784   (1679 kB)
<4>      .text : 0xc0100000 - 0xc02e8aea   (1954 kB)
<6>Checking if this processor honours the WP bit even in supervisor mode...Ok.
<7>CPA: page pool initialized 1 of 1 pages preallocated
<4>Calibrating delay using timer specific routine.. 3659.48 BogoMIPS (lpj=7318963)
<6>Security Framework initialized
<6>AppArmor: AppArmor initialized <NULL>
<6>AppArmor: Registered secondary security module capability
<6>Capability LSM initialized as secondary
<4>Mount-cache hash table entries: 512
<6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
<6>CPU: L2 Cache: 256K (64 bytes/line)
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<4>Compat vDSO mapped to ffffe000.
<6>Checking 'hlt' instruction... OK.
<6>SMP alternatives: switching to UP code
<6>Freeing SMP alternatives: 18k freed
<6>ACPI: Core revision 20070126
<6>ACPI: Checking initramfs for custom DSDT
<4>Parsing all Control Methods:
<4>Table [DSDT](id 0001) - 608 Objects with 57 Devices 167 Methods 27 Regions
<4> tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
<4>evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
<4>CPU0: AMD Athlon(tm) XP 2200+ stepping 00
<6>Total of 1 processors activated (3659.48 BogoMIPS).
<4>ENABLING IO-APIC IRQs
<6>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<6>Brought up 1 CPUs
<7>CPU0 attaching sched-domain:
<7> domain 0: span 00000000,00000000,00000000,00000001
<7>  groups: 00000000,00000000,00000000,00000001
<6>net_namespace: 548 bytes
<6>Booting paravirtualized kernel on bare hardware
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<6>PCI: PCI BIOS revision 2.10 entry at 0xfaf40, last bus=1
<6>PCI: Using configuration type 1
<6>Setting up standard PCI resources
<4>evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 0F [_GPE] 2 regs on int 0x9
<4>evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 1 Runtime GPEs in this block
<7>ACPI: EC: Look up EC in DSDT
<4>Completing Region/Field/Buffer/Package initialization:....................................................................
<4>Initialized 21/27 Regions 18/18 Fields 17/17 Buffers 12/21 Packages (617 nodes)
<4>Initializing Device/Processor/Thermal objects by executing _INI methods:..
<4>Executed 2 _INI methods requiring 1 _STA executions (examined 61 objects)
<6>ACPI: Interpreter enabled
<6>ACPI: (supports S0 S1 S4 S5)
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<6>pci 0000:00:11.0: quirk: region 4000-407f claimed by vt8235 PM
<6>pci 0000:00:11.0: quirk: region 5000-500f claimed by vt8235 SMB
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<6>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
<6>ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 6 7 10 11 12)
<6>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 *12)
<6>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12)
<6>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
<6>ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
<6>ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
<6>ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
<6>ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0
<6>ACPI: Power Resource [PFAN] (on)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>ACPI: bus type pnp registered
<6>pnp: PnP ACPI: found 12 devices
<6>ACPI: ACPI bus type pnp unregistered
<6>PnPBIOS: Disabled by ACPI PNP
<6>PCI: Using ACPI for IRQ routing
<6>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
<6>AppArmor: AppArmor Filesystem Enabled 
<4>ACPI: RTC can wake from S4
<6>system 00:00: iomem range 0xce400-0xcffff has been reserved
<6>system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
<6>system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
<6>system 00:00: iomem range 0xfc000-0xfffff could not be reserved
<6>system 00:00: iomem range 0x7fef0000-0x7fefffff could not be reserved
<6>system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
<6>system 00:00: iomem range 0x0-0x9ffff could not be reserved
<6>system 00:00: iomem range 0x100000-0x7feeffff could not be reserved
<6>system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
<6>system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
<6>system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
<6>system 00:02: ioport range 0x4000-0x407f has been reserved
<6>system 00:02: ioport range 0x5000-0x500f has been reserved
<6>system 00:03: ioport range 0x4d0-0x4d1 has been reserved
<6>system 00:03: ioport range 0x294-0x297 has been reserved
<6>PCI: Bridge: 0000:00:01.0
<6>  IO window: disabled.
<6>  MEM window: 0xdc000000-0xddffffff
<6>  PREFETCH window: 0x00000000d8000000-0x00000000dbffffff
<7>PCI: Setting latency timer of device 0000:00:01.0 to 64
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>Unpacking initramfs... done
<6>Freeing initrd memory: 5349k freed
<6>Machine check exception polling timer started.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(1229801597.648:1): initialized
<4>highmem bounce pool size: 64 pages
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>PCI: VIA PCI bridge detected. Disabling DAC.
<7>pci 0000:01:00.0: Boot video device
<6>vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 10240k, total 65536k
<6>vesafb: mode is 1280x1024x16, linelength=2560, pages=1
<6>vesafb: protected mode interface info at c000:dfa0
<6>vesafb: pmi: set display start = c00cdfe5, set palette = c00ce06a
<6>vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03 
<6>vesafb: scrolling: redraw
<6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<6>bootsplash 3.1.6-2004/03/31: looking for picture...
<6>bootsplash: silentjpeg size 208945 bytes
<6>bootsplash: ...found (1280x1024, 220863 bytes, v3).
<4>Console: switching to colour frame buffer device 156x60
<7>Switched to high resolution mode on CPU 0
<6>fb0: VESA VGA frame buffer device
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
<4>PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>mice: PS/2 mouse device common for all mice
<6>input: PC Speaker as /devices/platform/pcspkr/input/input0
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<4>registered taskstats version 1
<6>Freeing unused kernel memory: 264k freed
<6>Write protecting the kernel read-only data: 1436k
<6>input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
<6>ACPI: CPU0 (power states: C1[C1] C2[C2])
<6>ACPI: ACPI0007:00 is registered as cooling_device0
<6>ACPI: LNXTHERM:01 is registered as thermal_zone0
<6>ACPI: Thermal Zone [THRM] (58 C)
<6>No dock devices found.
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<7>pata_via 0000:00:11.1: version 0.3.3
<4>ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
<4>ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
<6>ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
<6>scsi0 : pata_via
<6>scsi1 : pata_via
<6>ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
<6>ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15
<4>Marking TSC unstable due to: TSC halts in idle.
<6>ata1.00: ATA-7: SAMSUNG SP2514N, VF100-50, max UDMA/100
<6>ata1.00: 488397168 sectors, multi 16: LBA48 
<6>ata1.00: configured for UDMA/100
<6>ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-H10N, JL10, max UDMA/33
<6>ata2.00: configured for UDMA/33
<5>scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG SP2514N  VF10 PQ: 0 ANSI: 5
<5>scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-H10N  JL10 PQ: 0 ANSI: 5
<6>ACPI: PNP0C0B:00 is registered as cooling_device1
<6>ACPI: Fan [FAN] (on)
<6>BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>USB Universal Host Controller Interface driver v3.0
<4>ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
<4>ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
<6>ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
<6>uhci_hcd 0000:00:10.0: UHCI Host Controller
<6>uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
<5>sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
<6>uhci_hcd 0000:00:10.0: irq 21, io base 0x0000d400
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<6>usb usb1: configuration #1 chosen from 1 choice
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>hub 1-0:1.0: USB hub found
<5>sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<6>hub 1-0:1.0: 2 ports detected
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
<5>sd 0:0:0:0: [sda] Attached SCSI disk
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: UHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.25.18-0.2-pae uhci_hcd
<6>usb usb1: SerialNumber: 0000:00:10.0
<6>ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
<6>ehci_hcd 0000:00:10.3: EHCI Host Controller
<6>ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 2
<6>ehci_hcd 0000:00:10.3: irq 21, io mem 0xde000000
<6>ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 6 ports detected
<6>usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: EHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.25.18-0.2-pae ehci_hcd
<6>usb usb2: SerialNumber: 0000:00:10.3
<6>ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
<6>uhci_hcd 0000:00:10.1: UHCI Host Controller
<6>uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
<6>uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d800
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: UHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.25.18-0.2-pae uhci_hcd
<6>usb usb3: SerialNumber: 0000:00:10.1
<6>usb 2-2: new high speed USB device using ehci_hcd and address 2
<6>ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
<6>uhci_hcd 0000:00:10.2: UHCI Host Controller
<6>uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
<6>uhci_hcd 0000:00:10.2: irq 21, io base 0x0000dc00
<6>usb usb4: configuration #1 chosen from 1 choice
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>usb 2-2: configuration #1 chosen from 1 choice
<6>usb 2-2: New USB device found, idVendor=04a9, idProduct=1729
<6>usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>usb 2-2: Product: MX700 series
<6>usb 2-2: Manufacturer: Canon
<6>usb 2-2: SerialNumber: 11B39C
<6>usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb4: Product: UHCI Host Controller
<6>usb usb4: Manufacturer: Linux 2.6.25.18-0.2-pae uhci_hcd
<6>usb usb4: SerialNumber: 0000:00:10.2
<3>hub 2-0:1.0: unable to enumerate USB device on port 3
<6>PM: Starting manual resume from disk
<3>hub 2-0:1.0: unable to enumerate USB device on port 6
<6>usb 3-1: new full speed USB device using uhci_hcd and address 2
<6>usb 3-1: configuration #1 chosen from 1 choice
<6>usb 3-1: New USB device found, idVendor=046d, idProduct=08da
<6>usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>usb 4-2: new low speed USB device using uhci_hcd and address 2
<6>usb 4-2: configuration #1 chosen from 1 choice
<6>usb 4-2: New USB device found, idVendor=046d, idProduct=c018
<6>usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 4-2: Product: USB Optical Mouse
<6>usb 4-2: Manufacturer: Logitech
<6>usbcore: registered new interface driver hiddev
<6>input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:10.2/usb4/4-2/4-2:1.0/input/input2
<6>input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:10.2-2
<6>usbcore: registered new interface driver usbhid
<6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on sda6, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>Linux agpgart interface v0.103
<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>Linux video capture interface: v2.00
<6>agpgart: Detected VIA KT400/KT400A/KT600 chipset
<6>agpgart: AGP aperture is 128M @ 0xd0000000
<6>usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04A9 pid 0x1729
<6>usblp1: USB Bidirectional printer dev 2 if 3 alt 0 proto 2 vid 0x04A9 pid 0x1729
<6>usbcore: registered new interface driver usblp
<6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>Initializing USB Mass Storage driver...
<6>input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
<6>scsi2 : SCSI emulation for USB Mass Storage devices
<6>ACPI: Power Button (FF) [PWRF]
<6>input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
<6>ACPI: Power Button (CM) [PWRB]
<6>input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<7>usb-storage: device found at 2
<7>usb-storage: waiting for device to settle before scanning
<6>ACPI: Sleep Button (CM) [SLPB]
<6>/usr/src/packages/BUILD/gspcav1-20071224/obj/pae/gspca_core.c: USB GSPCA camera found.(ZC3XX) 
<6>/usr/src/packages/BUILD/gspcav1-20071224/obj/pae/gspca_core.c: [spca5xx_probe:4275] Camera type JPEG 
<4>nvidia: module license 'NVIDIA' taints kernel.
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>scsi 1:0:0:0: Attached scsi generic sg1 type 5
<6>NET: Registered protocol family 23
<4>sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<5>scsi 2:0:0:0: Direct-Access     Canon    MX700 series     1080 PQ: 0 ANSI: 2
<7>sr 1:0:0:0: Attached scsi CD-ROM sr0
<5>sd 2:0:0:0: [sdb] Attached SCSI removable disk
<5>sd 2:0:0:0: Attached scsi generic sg2 type 0
<7>usb-storage: device scan complete
<6>/usr/src/packages/BUILD/gspcav1-20071224/obj/pae/Vimicro/zc3xx.h: [zc3xx_config:669] Find Sensor HV7131R(c)
<6>via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
<4>via-rhine: Broken BIOS detected, avoid_D3 enabled.
<6>/usr/src/packages/BUILD/gspcav1-20071224/obj/pae/gspca_core.c: [spca5xx_getcapability:1249] maxw 640 maxh 480 minw 160 minh 120
<6>usbcore: registered new interface driver gspca
<4>ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
<4>ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
<6>ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 23
<6>/usr/src/packages/BUILD/gspcav1-20071224/obj/pae/gspca_core.c: gspca driver 01.00.20 registered
<6>eth0: VIA Rhine II at 0x1e400, 00:50:8d:57:b7:01, IRQ 23.
<6>eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
<6>ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 19
<7>quickcam [32.306494]: ----------LOADING QUICKCAM MODULE------------
<7>quickcam [32.306502]: struct quickcam size: 4764
<6>usbcore: registered new interface driver quickcam
<6>rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
<6>rtc0: alarms up to one year, y3k
<6>parport_pc 00:0a: reported by Plug and Play ACPI
<6>parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
<6>usbcore: registered new interface driver snd-usb-audio
<6>ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
<4>NVRM: loading NVIDIA Linux x86 Kernel Module  96.43.07  Wed Jul  2 12:17:43 PDT 2008
<6>ppdev: user-space parallel port driver
<6>Adding 2104444k swap on /dev/sda5.  Priority:-1 extents:1 across:2104444k
<6>device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
<6>loop: module loaded
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on sda8, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<4>fuse init (API version 7.9)
<5>type=1505 audit(1229798021.977:2): operation="profile_load" name="/bin/ping" name2="default" pid=1339
<5>type=1505 audit(1229798022.085:3): operation="profile_load" name="/sbin/klogd" name2="default" pid=1347
<5>type=1505 audit(1229798022.185:4): operation="profile_load" name="/sbin/syslog-ng" name2="default" pid=1350
<5>type=1505 audit(1229798022.269:5): operation="profile_load" name="/sbin/syslogd" name2="default" pid=1357
<5>type=1505 audit(1229798022.357:6): operation="profile_load" name="/usr/sbin/avahi-daemon" name2="default" pid=1364
<5>type=1505 audit(1229798022.441:7): operation="profile_load" name="/usr/sbin/identd" name2="default" pid=1372
<5>type=1505 audit(1229798022.529:8): operation="profile_load" name="/usr/sbin/mdnsd" name2="default" pid=1382
<5>type=1505 audit(1229798022.613:9): operation="profile_load" name="/usr/sbin/nscd" name2="default" pid=1392
<5>type=1505 audit(1229798022.721:10): operation="profile_load" name="/usr/sbin/ntpd" name2="default" pid=1397
<5>type=1505 audit(1229798022.797:11): operation="profile_load" name="/usr/sbin/traceroute" name2="default" pid=1405
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Sat Dec 20 19:33:18 2008

Creating device nodes with udev
Trying manual resume from /dev/sda5
Invoking userspace resume from /dev/sda5
resume: libgcrypt version: 1.4.0
Trying manual resume from /dev/sda5
Invoking in-kernel resume from /dev/sda5
Waiting for device /dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 to appear:  ok
fsck 1.40.8 (13-Mar-2008)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: recovering journal
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181213 (uid=1000, gid=100, mode=0100600, size=2105)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181207 (uid=1000, gid=100, mode=0100600, size=100628)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181205 (uid=1000, gid=100, mode=0100600, size=40408)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181200 (uid=1000, gid=100, mode=0100600, size=2091)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181220 (uid=1000, gid=100, mode=0100600, size=2117)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 428013 (uid=1000, gid=100, mode=0100600, size=20500)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181228 (uid=1000, gid=100, mode=0100600, size=30913)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 428010 (uid=1000, gid=100, mode=0100600, size=149504)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181222 (uid=1000, gid=100, mode=0100600, size=12419)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181227 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181226 (uid=1000, gid=100, mode=0100600, size=35126)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181199 (uid=1000, gid=100, mode=0100600, size=120533)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181210 (uid=1000, gid=100, mode=0100600, size=35896)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181218 (uid=1000, gid=100, mode=0100600, size=24695)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181211 (uid=1000, gid=100, mode=0100600, size=27736)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181225 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181224 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181223 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181219 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181217 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181215 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181214 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181208 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181204 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181203 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181197 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 181195 (uid=1000, gid=100, mode=0140755, size=0)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: Clearing orphaned inode 427971 (uid=0, gid=0, mode=0100600, size=217016)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6: clean, 163784/1313280 files, 1210568/5242880 blocks
fsck succeeded. Mounting root device read-write.
Mounting root /dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6

Boot logging started on /dev/tty1(/dev/console (deleted)) at Sat Dec 20 20:33:29 2008

done
Starting udevd: done
Loading required kernel modules
doneActivating swap-devices in /etc/fstab...
donemount: according to mtab, /dev/sda6 is already mounted on /

Setting up the hardware clockdone
Activating device mapper...
done
Checking file systems...
fsck 1.40.8 (13-Mar-2008)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part8: recovering journal
/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part8: clean, 261695/14827520 files, 15999330/29653974 blocks
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda8 on /home type ext3 (rw,acl,user_xattr)
$LogFile indicates unclean shutdown (0, 1)
Failed to mount '/dev/sda1': Die Operation wird nicht unterstützt
Mount is denied because NTFS is marked to be in use. Choose one action:

Choice 1: If you have Windows then disconnect the external devices by
          clicking on the 'Safely Remove Hardware' icon in the Windows
          taskbar then shutdown Windows cleanly.

Choice 2: If you don't have Windows then you can use the 'force' option for
          your own responsibility. For example type on the command line:

            mount -t ntfs-3g /dev/sda1 /windows/C -o force

    Or add the option to the relevant row in the /etc/fstab file:

            /dev/sda1 /windows/C ntfs-3g force 0 0
failedFuse filesystem already availabledone
Mounting fuse control filesystemdone
Mounting securityfs on /sys/kernel/security done
Loading AppArmor profiles done
Cleaning up using /sbin/modify_resolvconf:
restored /etc/resolv.conf from /etc/resolv.conf.saved.by.pppd.dsl0
done
Creating /var/log/boot.msg
<notice>killproc: kill(570,29)
doneConfiguring serial ports...
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
Configured serial ports
doneActivating remaining swap-devices in /etc/fstab...
doneSetting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
fs.inotify.max_user_watches = 65536
net.ipv4.conf.default.promote_secondaries = 1
net.ipv4.conf.all.promote_secondaries = 1
done
Enabling syn flood protectiondone
Disabling IP forwardingdone
done
Setting up hostname 'linux-648q'done
Setting up loopback interface     lo        
    lo        IP address: 127.0.0.1/8   
              IP address: 127.0.0.2/8   
done
System Boot Control: The system has been set up
Skipped features: boot.cycle
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(570,3)

INIT: 
Boot logging started on /dev/tty1(/dev/console) at Sat Dec 20 19:33:44 2008

Master Resource Control: previous runlevel: N, switching to runlevel: 5
<notice>Entering runlevel: 5


startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
Starting resource managerdone
<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng -a /var/lib/dhcp/dev/log ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PWD=/ PREVLEVEL=N LINES=60 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
<notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/sbin/acpid ]
acpid: starting up


<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PWD=/ PREVLEVEL=N LINES=60 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/sbin/klogd ]
Starting syslog servicesdone
Starting acpid done
acpid: 1 rule loaded


Starting D-Bus daemondone
<notice>startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ]
Starting ConsoleKitdone
Starting Firewall Initialization (phase 1 of 2) done
Loading CPUFreq modules (CPUFreq not supported)
Starting HAL daemonLoading keymap i386/qwertz/de-latin1-nodeadkeys.map.gz
doneLoading compose table latin1.adddone
Start Unicode mode
doneLoading console font lat9w-16.psfu  -m trivial G0:loadable
doneStarting java.binfmt_misc done
Checking/updating CPU microcode unused
Initializing random number generatordone
TurboPrint daemon started
TP-Daemon Version 2.06-1
Debug Level set to 0
done
Setting up network interfaces:
    lo        
    lo        IP address: 127.0.0.1/8   
              IP address: 127.0.0.2/8   
done    eth0      device: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
    eth0      (DHCP) . . . . . . . . . . . . . . . no IP address yet... backgrounding. 
waiting
Waiting for mandatory devices:  eth0 __NSC__
4 3 1 0 
    eth0      device: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
    eth0      dhcpcd is still waiting for data
waiting
    eth0      interface could not be set up until now
failed    dsl0      
    dsl0      Startmode is 'manual'
skippedSetting up service network  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .failed
<notice>startproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ]
<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/sbin/portmap ]
Starting RPC portmap daemondone
Starting SSH daemondone
<notice>startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg LANG=de_DE.UTF-8 PREVLEVEL=N LINES=60 QT_SYSTEM_DIR=/usr/share/desktop-data HOME=/ SHLVL=2 XCURSOR_THEME=DMZ WINDOWMANAGER=/usr/bin/startkde3 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ]
Starting service kdmdone
<notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/sbin/auditd ]
Starting auditd done
Starting Avahi daemon.done
Starting cupsd<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ]
done
Starting Avahi DNS Configuration daemon<notice>startproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ]
done
Starting Name Service Cache Daemon<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
done
Starting mail service (Postfix)done
Starting CRON daemon<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
done
Starting powersaved: <notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ]
done
Starting Privoxy<notice>checkproc: /opt/kde3/bin/kdm 3084
done
Starting smartd <notice>startproc: execve (/usr/sbin/smartd) [ /usr/sbin/smartd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/smartd ]
done
Starting SMPPPD<notice>startproc: execve (/usr/sbin/smpppd) [ /usr/sbin/smpppd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/smpppd ]
done
Starting spamd <notice>startproc: execve (/usr/sbin/spamd) [ /usr/sbin/spamd -d -c -L -r /var/run/spamd.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=156 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=60 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SP2514NS08BJ1ELA05492-part6 _=/sbin/startproc DAEMON=/usr/sbin/spamd ]
failed
Starting Firewall Initialization (phase 2 of 2) done
done
Master Resource Control: runlevel 5 has been reached
Failed services in runlevel 5: network spamd
Skipped services in runlevel 5: microcode.ctl
<notice>killproc: kill(1651,3)
schneevater
Newbie
Newbie
Beiträge: 37
Registriert: 21. Sep 2005, 16:05

Re: System hängt sich auf beim Audio-Cd auslesen

Beitrag von schneevater »

Hallo,

such mal im Kontrollzentrum von KDE nach einem Punkt der sich "Fehlerkorrektur" nennt. Ist irgendwo unter Multimedia / Soundsystem zu finden.
Deaktivier die Fehlerkorrektur und versuch dann mal die CD's auszulesen.

Ein ähnliches Problem hatte ich auch beim Auslesen von Audio-CD's. Allerdings mit KAudioCreator und LAME. Bei einigen CD's blockierte KAudioCreator bei eingeschalteter Fehlerkorrektur ohne, meiner Meinung nach, erkannbaren Grund. Die CD's waren nicht zerkratzt und oder oder sonst irgendwie beschädigt.
Mal blockierte KAudioCreator bei 80% dann wieder bei 20%, 40% usw. Ohne Fehlerkorrektur konnte ich bisher alle CD's ohne Probleme Auslesen.
Antworten