• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst] bcm43xx unter SuSe 10.2 x86_64

lomo2003

lomo2003

Member
Hallo und gute Tag,
ich habe folgendes Problem!!!

Wenn ich SuSe 10.2 x86_64 starte funzt die Wirelesskarte nicht.
aber wenn ich zuvor SuSE 10.1 gestartet habe und dann danach ein reboot mache und SuSe 10.2 x86_64 starte wird die Karte eingerichtet und funktioniert!!!!
HHmm????

Unter SUSE 10.1 wird die Karte mit Ndiswrapper eingebunden.
Unter SuSe 10.2 x86_64 habe ich die Katen mittels Kernelmodul "bcm43xx" eingebunden.

dmesg sagt mir, wenn die Karten nicht funzt:
Code: 
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
ieee80211_crypt: registered algorithm 'WEP'
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22  19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
Losing some ticks... checking if CPU frequency changed.
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
audit(1168027069.684:3): audit_backlog_limit=256 old=64 by auid=4294967295
audit(1168027069.776:4): audit_pid=3715 old=0 by auid=4294967295
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Initialized drm 1.0.1 20051102
GSI 23 sharing vector 0x42 and IRQ 23
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 66
[drm] Initialized radeon 1.25.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
ieee80211_crypt: registered algorithm 'TKIP'
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
ieee80211_crypt: registered algorithm 'CCMP'
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22  19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22  19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished

und nach dem reboot von 10.1 zu 10.2 :
Code: 
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
ieee80211_crypt: registered algorithm 'WEP'
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22  19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Already requested authentication, waiting...
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
SoftMAC: Open Authentication completed with 00:40:05:5e:2a:ca
SoftMAC: sent association request!
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
Losing some ticks... checking if CPU frequency changed.
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
SoftMAC: Open Authentication completed with 00:40:05:5e:2a:ca
SoftMAC: sent association request!
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
SoftMAC: sent association request!
audit(1168027950.566:3): audit_pid=3721 old=0 by auid=4294967295
SoftMAC: assoc request timed out!
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Initialized drm 1.0.1 20051102
GSI 23 sharing vector 0x42 and IRQ 23
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 66
[drm] Initialized radeon 1.25.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:01:00:04:0e:a9:14:27:08:00 SRC=192.168.0.254 DST=224.0.0.1 LEN=36 TOS=0x00 PREC=0xC0 TTL=1 ID=46850 DF OPT (94040000) PROTO=2
psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.
ieee80211_crypt: registered algorithm 'TKIP'
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
ieee80211_crypt: registered algorithm 'CCMP'
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22  19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
SoftMAC: Canceling existing associate request!
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
NET: Registered protocol family 17
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
bcm43xx: set security called, .active_key = 0, .enabled = 1, .encrypt = 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .active_key = 0, .enabled = 1, .encrypt = 1
SoftMAC: Already associating or associated to 00:40:05:5e:2a:ca
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
bcm43xx: set security called, .active_key = 0, .enabled = 1, .encrypt = 1
SoftMAC: Already associating or associated to 00:40:05:5e:2a:ca
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
printk: 9 messages suppressed.
SoftMAC: Open Authentication completed with 00:40:05:5e:2a:ca
SoftMAC: sent association request!
SoftMAC: associated!
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
eth0: no IPv6 routers present
SoftMAC: Scanning finished

Wie kann ich dies lösen das die Karte direkt nach dem Einschalten funktioniert!!!

THX im voraus ToM.
 
OP
lomo2003

lomo2003

Member
Habe heute dein Ndiswrapper installiert aber auch hier ist das gleiche Problem!!!
Erst nach einen reboot von 10.1 zu 10.2 funktioniert die WLAN-Karte :cry:

Greetz ToM.
 
S

stka

Guru
Hast du die Firmware installiert? Ich habe gerade auch eine solche Karte installiert. Dafür gibt es ein tool bcm43xx-fwcutter, der die Firmware aus dem Treber entpackt und bereit stellt. Schau mal hier da ist das beschrieben wie das geht. Geht da zwar um ubuntu sollte aber auch unter suse gehen:
http://www.ubuntuforums.org/showthread.php?t=185174
 
OP
lomo2003

lomo2003

Member
Jepp, habe dieFirmware mit bcm43xx-fwcutter installiert!!!

Die Karte Funktionert ja 100% aber eben erst nach dem reboot.

Greetz ToM
 
J

jengelh

Guru
lomo2003 schrieb:
Jepp, habe dieFirmware mit bcm43xx-fwcutter installiert!!!
Die Karte Funktionert ja 100% aber eben erst nach dem reboot.
Zum Vergrößern anklicken....
Nein, die funktioniert auch schon nach `rmmod bcm43xx; modprobe bcm43xx`, also nach Treiber neu laden. Reboot, das ist wirklich Windows-style.
 
C

carsten

Guru
Bei mir gehts nie nach nem Booten, nur danach mit rmmod und modprobe im Betrieb.

Keine Ahnung warum und es nervt, denn vieles wird ja schon beim Booten im Netz abgefragt (und wenns die IP ist).

Grüße

PS: bei mir mit 32 bit und 10.2 (mein Lap, also nicht der aus der Signatur)
 
OP
lomo2003

lomo2003

Member
jengelh schrieb:
lomo2003 schrieb:
Jepp, habe dieFirmware mit bcm43xx-fwcutter installiert!!!
Die Karte Funktionert ja 100% aber eben erst nach dem reboot.
Zum Vergrößern anklicken....
Nein, die funktioniert auch schon nach `rmmod bcm43xx; modprobe bcm43xx`, also nach Treiber neu laden. Reboot, das ist wirklich Windows-style.
Zum Vergrößern anklicken....

Arrrg, also OHNE reboot gehts einfach net :evil: .

Habe rmmod und modprobe jeweils mit dem bcm43xx Moduls sowie dem ndiswrapper ausprobiert!.

Help ToM.

LOL Novell und Microsoft machen ja schon gemeinsame Sache LOL
 
J

jengelh

Guru
Hm das erscheint mir doch recht strange - weil zwischen Modul laden und Reboot seh ich nicht so sonders den Unterschied (unter Windows meist Rebooten weil sonst der Treiber nie entladen wird).
 
OP
lomo2003

lomo2003

Member
:D :D :D ICH HABS HIN BEKOMMEN :D :D :D :D

Die WLanKarte wird mittels des Programm acerhk ( acerhk-0.5.34.tar.bz2 ) ein und ausgeschaltet.

Dieses Programm übersetzt und installiert und siehe da sie funktioniert jetzt direkt nach dem einschalten.

Ich kann diese Programm, wenn nötigt, zum download bereit stellen!


Greetz ToM.

Nachtrag:

http://gentoo.osuosl.org/distfiles/acerhk-0.5.34.tar.bz2
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben