Diese Website existiert nur weil wir Werbung mit AdSense ausliefern.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.

orinoco gold classic unter suse 9.2 funkt nicht

Alles rund um das Internet, Internet-Anwendungen (E-Mail, Surfen, Cloud usw.) und das Einrichten von Netzwerken einschl. VPN unter Linux

Moderator: Moderatoren

Antworten
Benutzeravatar
switchding
Newbie
Newbie
Beiträge: 10
Registriert: 6. Jun 2004, 13:13
Wohnort: Bayern

orinoco gold classic unter suse 9.2 funkt nicht

Beitrag von switchding »

hallo!

ich habe mir eine ORINOCO GOLD CLASSIC PCMCIA Wlan Karte kehauft, da es heißt, die funktioniert einwandfrei.

is aber nicht so!

Ich stecke die Karte ein, "Neue Hardware gefunden....Konfigurieren...?" erscheint. Ich drücke auf ja, YAST wird geöffnet, ich gebe die gewünschten daten ein und rücke auf beenden.

Nix funzt! Nicht mal den AP kann ich pingen.

Was habe ich falsch gemacht?

mfg
Benutzeravatar
switchding
Newbie
Newbie
Beiträge: 10
Registriert: 6. Jun 2004, 13:13
Wohnort: Bayern

Beitrag von switchding »

Ich bins nochmal!

Hier noch ein paar weitere Angaben zu meinem Problem:

unter /etc/sysconfig/network/wireless steht folgendes:

## Path: Hardware/Wireless
## Description:
## Type: yesno
## Default: ""
## ServiceRestart: network
# If you have a wireless NIC and want to set some special wireless parameters
# then you can do that here in this file globally for all cards you have. But
# you can write each of these variables to the interface specific ifcfg-* files
# to handle things per card.
# The WIRELESS_* variable names match the option names of iwconfig. Have a look
# at 'man iwconfig' for details. Except WIRELESS_NICK the variables do nothing
# if empty.
#
# This variables decides if the special handling for wireless HW is used. If you
# have only one network interface card and it is wireless you can set it here to
# 'yes'. But it is much better, if you use that variable in the interface
# configuration files 'ifcfg-*', which overrides the general settings made here.
WIRELESS=""

## Type: string
## Default: ""
# Set the operating mode of the device, which depends on the network
# topology. The mode can be Ad-hoc (network composed of only one cell and
# without Access Point), Managed (network composed of many cells, with
# roaming or with an Access Point), Mas ter (the node is the synchronisation
# master or act as an Access Point), Repeater (the node forward packets on the
# air), Secondary (the node act as a backup master/repeater) or Auto
WIRELESS_MODE=""

## Type: string
## Default: ""
# Set the ESSID (or Network Name - in some products it may also called Domain
# ID). The ESSID is used to identify cells which are part of the same virtual
# network.
WIRELESS_ESSID=""

## Type: string
## Default: ""
# Set the nickname, or the station name. Most 802.11 products do define it,
# but this is not used as far as the protocols (MAC, IP, TCP) are concerned
# and completely accessory as far as configuration goes. If this variable is
# empty we use the hostname
WIRELESS_NICK=""

## Type: string
## Default: ""
# Set the Network ID (in some products it is also called Domain ID). As all
# adjacent wireless net works share the same medium, this parameter is used
# to differenciate them (create logical colocated networks) and identify
# nodes belonguing to the same cell.
WIRELESS_NWID=""

## Type: string
## Default: ""
# Set the operating frequency or channel in the device. Value below
# 1000 are the channel number, value over this is the frequency in Hz. You
# must append the suffix k, M or G to the value (for exam ple, "2.46G" for
# 2.46 GHz frequency), or add enough '0'.
WIRELESS_FREQ=""

## Type: string
## Default: ""
# Channels are usually numbered starting at 1, and you may use iwpriv(8) to
# get the total number of channels and list the available frequencies.
# Depending on regulations, some frequencies/channels may not be available.
WIRELESS_CHANNEL=""

## Type: string
## Default: ""
# Set the sensitivity threshold. This is the lowest signal level for which we
# attempt a packet recep tion, signal lower than this are not received. This
# is used to avoid receiving background noise
WIRELESS_SENS=""

## Type: string
## Default: ""
# For cards supporting multiple bit rates, set the bit-rate in b/s. The
# bit-rate is the speed at which bits are transmitted over the medium, the
# user speed of the link is lower due to medium sharing and overhead.
WIRELESS_RATE=""

## Type: string
## Default: ""
# Used to manipulate encryption or scrambling keys and encryption mode. To
# set the current encryption key, just enter the key in hex digits as
# XXXX-XXXX-XXXX-XXXX or XXXXXXXX. You can also enter the key as an ASCII
# string by using the s: prefix. 'off' disables encryption. Additionally you
# may add 'open' or 'restricted' after the key, open set the system in open
# mode (accept non-encrypted packets) and restricted discard non-encrypted
# packets.
# Examples: "0123-4567-89"
# "s:password"
# "s:password open"
# "off" (Don't do that! No! No! No!)
WIRELESS_KEY=""

## Type: string
## Default: ""
# RTS/CTS adds a handshake before each packet trans mission to make sure
# that the channel is clear. This adds overhead, but increase performance
# in case of hidden nodes or large number of active nodes.
WIRELESS_RTS=""

## Type: string
## Default: ""
# Fragmentation allow to split a IP packet in a burst of smaller fragments
# transmitted on the medium. In most cases this adds overhead, but in very
# noisy environment this reduce the error penalty.
WIRELESS_FRAG=""

## Type: string
## Default: ""
# If you need other options for iwconfig, then write the complete option string
# as you would append it to iwconfig but without the interface name to the
# variables below. For multiple options you may (but need not) add linebreaks in
# the string.
WIRELESS_IWCONFIG_OPTIONS=""

## Type: string
## Default: ""
# If you need to set options for iwspy, then write the complete option string as
# you would append it to iwspy but without the interface name to the variables
# below. For multiple options you may (but need not) add linebreaks in the
# string.
WIRELESS_IWSPY_OPTIONS=""

## Type: string
## Default: ""
# If you need to set options for iwpriv then write the complete option string as
# you would append it to iwpriv but without the interface name to the variables
# below. For multiple options you may (but need not) add linebreaks in the
# string.
WIRELESS_IWPRIV_OPTIONS=""


Warum habe ich nur lauter " " ? Müßten da nicht die eingestellten Parameter von YAST stehen?

Wenn ich ifconfig eingebe, erscheint das:

eth0 Protokoll:Ethernet Hardware Adresse 00:03:25:10:F6:22
inet Adresse:10.0.0.3 Bcast:10.0.0.255 Maske:255.255.255.0
inet6 Adresse: fe80::203:25ff:fe10:f622/64 Gültigkeitsbereich:Verbindung
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1285 errors:0 dropped:0 overruns:0 frame:0
TX packets:311 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 Sendewarteschlangenlänge:1000
RX bytes:193098 (188.5 Kb) TX bytes:101930 (99.5 Kb)
Interrupt:193 Basisadresse:0x1800

eth1 Protokoll:Ethernet Hardware Adresse 00:02:2D:C3:D7:4B
inet Adresse:10.0.0.5 Bcast:10.0.0.255 Maske:255.255.255.0
inet6 Adresse: fe80::202:2dff:fec3:d74b/64 Gültigkeitsbereich:Verbindung
UP BROADCAST NOTRAILERS RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:1081 errors:35 dropped:35 overruns:0 frame:35
TX packets:100 errors:15 dropped:0 overruns:0 carrier:0
collisions:0 Sendewarteschlangenlänge:1000
RX bytes:64363 (62.8 Kb) TX bytes:19140 (18.6 Kb)
Interrupt:169 Basisadresse:0x100

lo Protokoll:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:233 errors:0 dropped:0 overruns:0 frame:0
TX packets:233 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 Sendewarteschlangenlänge:0
RX bytes:20692 (20.2 Kb) TX bytes:20692 (20.2 Kb)


Und bei ifstatus eth1 folgendes:

# ifstatus eth1
eth1 device: Lucent Technologies WaveLAN/IEEE Adapter
eth1 configuration: wlan-bus-pcmcia
eth1 DHCP client NOT running
5: eth1: <BROADCAST,MULTICAST,PROMISC,NOTRAILERS,UP> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 00:02:2d:c3:d7:4b brd ff:ff:ff:ff:ff:ff
inet 10.0.0.5/24 brd 10.0.0.255 scope global eth1
inet6 fe80::202:2dff:fec3:d74b/64 scope link
valid_lft forever preferred_lft forever
eth1 IEEE 802.11-DS ESSID:"dahoam" Nickname:"laptop"
Mode:Managed Frequency:2.462 GHz Access Point: 00:09:5B:4F:7A:F6
Bit Rate:11 Mb/s Tx-Power=15 dBm Sensitivity:1/3
Retry limit:4 RTS thr:off Fragment thr:off
Encryption key:2CC0-8030-F87A-7617-B062-A574-DB
Power Management:off
Link Quality=61/92 Signal level=-40 dBm Noise level=-101 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:5
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

Diese Befehle habe ich aus verschiedenen "Linux"- Zeitschriften.
Aber was das alles heisen soll, keine Ahnung!!!!!

Ich hoffe, dass da drausen irgend jemand ist, der mir nun weiterhelfen kann!

Danke und bis hoffentlich bald!
Benutzeravatar
switchding
Newbie
Newbie
Beiträge: 10
Registriert: 6. Jun 2004, 13:13
Wohnort: Bayern

Jetzt gehts

Beitrag von switchding »

Ich bin nun von Suse 9.3 auf Ubuntu umgestiegen. Habe die Karte eingesteckt, schon lief sie!

Somit kein Problem mehr!
Antworten