Ich habe schon vor einiger Zeit im deutschen RasPI-Forum eine Anfrage gestellt, leider weiß man da anscheinend nicht mehr weiter. Seit einigen Wochen verwende ich einen RasPI 4B mit 4GB RAM als Server unter Raspian Bulls Eye. Auf dem RasPI läuft meine Hausautomatisierung (diverse ESP8266 mit eigener Firmware). Der LAN-Port hängt im Netz, das WLAN spannt ein eigenes Netz auf (AP auf dem RasPI), ohne Bridge zum LAN.
Vor ca. einer Woche habe ich festgestellt, daß dnsmaq nur bis zu neun Geräten eine IP-Adresse zuweist. Wenn ich versuche, ein zehntes Gerät anzumelden, bekommt dieses keine IP-Adresse. Ich habe inzwischen schon dnsmasq so konfiguriert das er etwas gesprächiger wird, aber er erzählt leider nicht viel. Ich würde z.B. gerne wissen, ob die Anfragen überhaupt ankommen. Leider funktioniert das anscheinend nicht. Es werden immer nur max. neun Leases angezeigt.
Hier für alle Fälle schon mal die aktuelle dnsmasq.conf:
und für alle Fälle die hostapd.conf:
Jemand eine Idee, wo ich noch suchen könnte? Mir gehen die Ideen aus.
CU Freddie
Vor ca. einer Woche habe ich festgestellt, daß dnsmaq nur bis zu neun Geräten eine IP-Adresse zuweist. Wenn ich versuche, ein zehntes Gerät anzumelden, bekommt dieses keine IP-Adresse. Ich habe inzwischen schon dnsmasq so konfiguriert das er etwas gesprächiger wird, aber er erzählt leider nicht viel. Ich würde z.B. gerne wissen, ob die Anfragen überhaupt ankommen. Leider funktioniert das anscheinend nicht. Es werden immer nur max. neun Leases angezeigt.
Hier für alle Fälle schon mal die aktuelle dnsmasq.conf:
Code:
cat /etc/dnsmasq.conf
# Configuration file for dnsmasq.
#
# Never forward plain names (without a dot or domain part)
domain-needed
# Never forward addresses in the non-routed address spaces.
bogus-priv
# If you want dnsmasq to listen for DHCP and DNS requests only on
# specified interfaces (and the loopback) give the name of the
# interface (eg eth0) here.
# Repeat the line for more than one interface.
interface=wlan0
# Or you can specify which interface _not_ to listen on
#except-interface=
# Or which to listen on by address (remember to include 127.0.0.1 if
# you use this.)
#listen-address=
# If you want dnsmasq to provide only DNS service on an interface,
# configure it as shown above, and then use the following line to
# disable DHCP and TFTP on it.
no-dhcp-interface=eth0
# Uncomment this to enable the integrated DHCP server, you need
# to supply the range of addresses available for lease and optionally
# a lease time. If you have more than one network, you will need to
# repeat this for each network on which you want to supply DHCP
# service.
dhcp-range=192.168.100.10,192.168.100.100,255.255.255.0,24h
#domain=wlan
#address=/gw.wlan/192.168.100.1
# Set the limit on DHCP leases, the default is 150
dhcp-lease-max=100
# The DHCP server needs somewhere on disk to keep its lease database.
# This defaults to a sane location, but if you want to change it, use
# the line below.
#dhcp-leasefile=/var/lib/misc/dnsmasq.leases
# For debugging purposes, log each DNS query as it passes through
# dnsmasq.
log-queries
# Log lots of extra information about DHCP transactions.
log-dhcp
log-facility=/var/log/dnsmasq.log
Code:
cat /etc/hostapd/hostapd.conf
# WLAN-Router-Betrieb
# Schnittstelle und Treiber
interface=wlan0
#driver=nl80211
# WLAN-Konfiguration
ssid=Mein_WLAN
channel=5
hw_mode=g
ieee80211n=1
ieee80211d=1
country_code=DE
wmm_enabled=1
# WLAN-Verschlüsselung
auth_algs=1
wpa=2
wpa_key_mgmt=WPA-PSK
rsn_pairwise=CCMP
wpa_passphrase=Geheimes_Passwort
CU Freddie