Diese Website existiert nur weil wir Werbung mit AdSense ausliefern.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.
Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Moderator: Moderatoren
Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Gleich vorweg! Meine Frau setzt ein Toshiba Satelite Notebook mit nur 512 MB Hauptspeicher ein. Windows XP konnte nicht weiter eingesetzt werden. Also habe ich ihr Puppy 5.3 installiert. Das läuft auch soweit ganz ordentlich. Allerdings kann ich unseren Canon Pixma MG6150 Drucker nicht installieren.
Also habe ich auf einem alten Desktop Puppeinsetzen.y Slacko 6.3.2 installiert. Hier konnte ich die Druckertreiber mit Hilfe des Puppy Linux Discussion Forum installieren. Allerdings bekomme ich keine Antwort auf mein Problem mit der Installation von Puppy Slacko auf dem Notebook. Nachdem Einlesen der CD und Start von X bekomme ich nur einen weißen Bildschirm zu sehen. Grund ist, das der Bildschirm/ die Grafikarte mit 1024x768 Pixel nur eine Bildwiederholrate von maximal 60 Hz zulässt Puppy Slacko aber stets 75 Hz einstellt. Ich finde keine Möglichkeit, diese Einstellung zu ändern.
Wer kann mir helfen das zu ändern. Das wäre sehr wichtig, denn dann könnte meine Frau aktuellere Programme z.B. den Browser Firefox einsetzen weil der SeaMonkey unter Puppy 5.3 nicht sauber arbeitet.
Also habe ich auf einem alten Desktop Puppeinsetzen.y Slacko 6.3.2 installiert. Hier konnte ich die Druckertreiber mit Hilfe des Puppy Linux Discussion Forum installieren. Allerdings bekomme ich keine Antwort auf mein Problem mit der Installation von Puppy Slacko auf dem Notebook. Nachdem Einlesen der CD und Start von X bekomme ich nur einen weißen Bildschirm zu sehen. Grund ist, das der Bildschirm/ die Grafikarte mit 1024x768 Pixel nur eine Bildwiederholrate von maximal 60 Hz zulässt Puppy Slacko aber stets 75 Hz einstellt. Ich finde keine Möglichkeit, diese Einstellung zu ändern.
Wer kann mir helfen das zu ändern. Das wäre sehr wichtig, denn dann könnte meine Frau aktuellere Programme z.B. den Browser Firefox einsetzen weil der SeaMonkey unter Puppy 5.3 nicht sauber arbeitet.
Werbung:
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Post doch mal die "/etc/X11/xorg.conf".
Oder existiert das Verzeichnis "/etc/X11/xorg.conf.d" mit weiteren Dateien darin?
Ich persönlich mag auch Puppy Linux 2.14X.
Die Canon-Seite hat auch durchaus ein paar Linux 32bit-Treiber für diesen Drucker.
Oder existiert das Verzeichnis "/etc/X11/xorg.conf.d" mit weiteren Dateien darin?
Ich persönlich mag auch Puppy Linux 2.14X.
Die Canon-Seite hat auch durchaus ein paar Linux 32bit-Treiber für diesen Drucker.
-
- Ultimate Guru
- Beiträge: 5170
- Registriert: 23. Sep 2008, 17:09
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Versuche im Boot-Menü die Boot-Option:
Code: Alles auswählen
video=1024x768@60
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Erst einmal Danke für die Tipps und Hinweise Euch beiden.
Also die alte Installation von Puppy 5.3, die auf dem Notebook läuft, enthält folgende xorg.conf:
Und die Installation auf dem Test-PC Puppy Slacko 6.3.2 die folgende:
Im xorg.conf.d-Verzeichnis gibt es keine Dateien.
An die xorg.conf vom ISO-Image der Boot-CD komme ich nicht ran. Oder gibt es eine Möglichkeit die xorg.conf auf dem ISO-Image zu verändern?
Unter Slacko konnte ich die Treiber für den Drucker Pixma MG6150 mit Hilfe von "candi-1.4.pet" installieren mit:
Quelle:
http://murga-linux.com/puppy/viewtopic. ... 110#644110
Candi läuft aber nicht unter Puppy 5.3. Jedenfalls habe ich es nicht geschafft.
Nun zu den Bootoptionen
Auf der Boot-CD von Slacko gibt es keine Bootoption "Alles Auswählen" sondern nur die Möglichkeit
- ohne Safe fileMaschinen
- mit Safe file
- ohne Grafikdesktop
- verschiedenen Grafikproblemen
Sobald es an die Konfiguration "Sprache auswählen" geht, wird der Bildschirm bei allen Optionen weiss und man kann nichts mehr sehen und folglich auch nichts eingeben. Das ist frustrierend. Wie kann man Puppy dazu bringen keine zu hohe Bildfrequenz einzustellen.
Mit Tab komme ich auf den Prompt:
"> .linux vmlinuz pfix=nox initrd=initrd.gz"
wenn ich video=1024x768&60 zusätzlich eingebe, kommt das gleiche Ergebnis "weißer Bildschirm". Früher war das besser geregelt. Da konnte die Bildschrmeinstellung selber auswählen
Also die alte Installation von Puppy 5.3, die auf dem Notebook läuft, enthält folgende xorg.conf:
Code: Alles auswählen
#Special base config file uauswählesed din Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# *************************************************Vom*********************
#d
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"d
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"auswähle
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (dif present)
Load "glx"
# This loads dri module (if present)
Load "dri"
EndSection
# ***************************d*******************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
d
RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
d
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable dthe <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"d
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboardd0" "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "de" #xkeymap0
EndSection
Section "InputDevice"auswähle
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5-48.5
VertRefresh 40-70
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode" "1024x768"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" d # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nv" #card0dridver
VendorName "nVidia Corporation"
BoardName "NV11 [GeForce2 Go]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
#Option "metamodes" "1024x768_60 +0+0" #METAMODES_0
Subsection "Display"
Depth 16#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (if present)
Load "glx"
# This loads dri module (if present)
Load "dri"d
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
d
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "de" #xkeymap0
EndSection
d
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5-48.5
VertRefresh 40-70
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (if present)
Load "glx"
# This loads dri module (if present)
Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "InputDevice"d
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "de" #xkeymap0
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5-48.5
VertRefresh 40-70
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode" "1024x768"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>auswähle
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" d # [<bool>]
Identifier "Card0"
Driver "nv" #card0driver
VendorName "nVidia Corporation"
BoardName "NV11 [GeForce2 Go]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"d
Monitor "Monitor0"
DefaultDepth 16
#Option "metamodes" "1024x768_60 +0+0" #METAMODES_0
Subsection "Display"
Depth 16
Modes "1024x768"
EndSubsection
EndSection
#PuppyHardwareProfile=NVidia
" "1024x768"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFdB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHeadd" # [<bool>]
Identifier "Card0"
Driver "nv" #card0driver
VendorName "nVidia Corporation"
BoardName "NV11 [GeForce2 Go]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"d
DefaultDepth 16
#Option "metamodes" "1024x768_60 +0+0" #METAMODES_0
Subsection "Display"
Depth 16
Modes "1024x768"
EndSubsection
EndSection
#PuppyHardwareProfile=NVidia
Modes "1024x768"d
EndSubsection
EndSection
#PuppyHardwareProfile=NVidia
Code: Alles auswählen
#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
# Load "type1"
# Load "freetype"
# This loads xtrap extension, used by xrandr
# Load "xtrap"
# This loads the GLX module (if present). xorg 7.4/5 need explicit disable to disable...
# Disable "glx" #LOADGLX
# This loads dri module (if present). 7.4 loads it by default, have to disable...
# Load "dri" #LOADDRI
# Disable "dri"
EndSection
# **********************************************************************
# Files section. This allows default font paths to be set
# **********************************************************************
Section "Files"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/share/X11/fonts/misc/"
FontPath "/usr/share/X11/fonts/Type1/"
FontPath "/usr/share/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
# With this, Xorg won't talk to HAL to add evdev devices and you'll be back
# with the old Xorg behavior (pre-7.4)...
Option "AutoAddDevices" "false"
# For no-Hal, kirk also suggests this...
# Option "AllowMouseOpenFail" "true"
# Xorg 7.4, Ubuntu Jaunty, CTRL-ALT-BACKSPACE is disabled by default...
Option "DontZap" "false"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "Default Layout"
Screen "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "de" #xkeymap0
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "Protocol" "IMPS/2" #mouse0protocol
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
#HorizSync 31-50
VertRefresh 59-76
#UseModes "Modes0" #monitor0usemodes
Option "PreferredModde" "1024x768"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
### Values: <i>: integder, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
### <percent>: "<f>%"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "AccelMethod" # <str>
#Option "Backlight" # <str>
#Option "DRI" # <str>
#Option "ColorKey" # <i>
#Option "VideoKey" # <i>
#Option "Tiling" # [<bool>]
#Option "LinearFramebuffer" # [<bool>]
#Option "SwapbuffersVomWait" # [<bool>]
#Option "TripleBuffer" # [<bool>]
#Option "XvPreferOverlay" # [<bool>]
#Option "HotPlug" # [<bool>]
#Option "ReprobeOutputs" # [<bool>]
#Option "XvMC" # [<bool>]
#Option "ZaphodHeads" # <str>
#Option "TearFree" # [<bool>]
#Option "PerCrtcPixmaps" # [<bool>]
#Option "FallbackDebug" # [<bool>]
#Option "DebugFlushBatches" # [<bool>]
#Option "DebugFlushCaches" # [<bool>]
#Option "DebugWait" # [<bool>]
#Option "BufferCache" # [<bool>]
Identifier "Card0"
Driver "intel" #card0driver
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"Vom
Monitor "Monitor0"
DefaultDepth 24
#Option "metamodes" "1024x768_60 +0+0" #METAMODES_0
Subsection "Display"
Depth 24
Modes "1024x768"
EndSubsection
EndSection
#PuppyHardwareProfile=Intel_r_Broadwater_G_Graphics_Chip
An die xorg.conf vom ISO-Image der Boot-CD komme ich nicht ran. Oder gibt es eine Möglichkeit die xorg.conf auf dem ISO-Image zu verändern?
Unter Slacko konnte ich die Treiber für den Drucker Pixma MG6150 mit Hilfe von "candi-1.4.pet" installieren mit:
Code: Alles auswählen
candi cnijfilter-common_3.40-1_i386.deb
candi cnijfilter-ip2700series_3.40-1_i386.deb
http://murga-linux.com/puppy/viewtopic. ... 110#644110
Candi läuft aber nicht unter Puppy 5.3. Jedenfalls habe ich es nicht geschafft.
Nun zu den Bootoptionen
Auf der Boot-CD von Slacko gibt es keine Bootoption "Alles Auswählen" sondern nur die Möglichkeit
- ohne Safe fileMaschinen
- mit Safe file
- ohne Grafikdesktop
- verschiedenen Grafikproblemen
Sobald es an die Konfiguration "Sprache auswählen" geht, wird der Bildschirm bei allen Optionen weiss und man kann nichts mehr sehen und folglich auch nichts eingeben. Das ist frustrierend. Wie kann man Puppy dazu bringen keine zu hohe Bildfrequenz einzustellen.
Mit Tab komme ich auf den Prompt:
"> .linux vmlinuz pfix=nox initrd=initrd.gz"
wenn ich video=1024x768&60 zusätzlich eingebe, kommt das gleiche Ergebnis "weißer Bildschirm". Früher war das besser geregelt. Da konnte die Bildschrmeinstellung selber auswählen
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Danke für die Infos.
Dieser Prompt ist schonmal die richtige Stelle, um das einzugeben. Aber es muß "video=1024x768@60" heißen, also "@" statt "&". Bringt das was?
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Siehst Du die Monitor-Section in der xorg.conf?
Diese läuft:
Diese nicht:
Müßtest halt versuchen, die untere mehr der oberen anzupassen (HorizSync, VertRefresh). Aber bitte mach vorher eine Sicherungskopie.
Diese läuft:
Code: Alles auswählen
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5-48.5
VertRefresh 40-70
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode" "1024x768"
EndSection
Code: Alles auswählen
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
#HorizSync 31-50
VertRefresh 59-76
#UseModes "Modes0" #monitor0usemodes
Option "PreferredModde" "1024x768"
EndSection
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Der Video-String mit @ vor der 60 funktioniert auch nicht.
Die xorg.conf kann ich im ISO-File nicht verändern, da ich da nicht dran komme. Ich wüste auch nicht, wie ich das dann in dem ISO-File speichern sollte. Ich müsste mir ein eigenes ISO basteln. Das kann ich aber nicht. Ich müsste an die Entwickler herantreten. Wie das geht, weiß ich auch nicht.
Die xorg.conf kann ich im ISO-File nicht verändern, da ich da nicht dran komme. Ich wüste auch nicht, wie ich das dann in dem ISO-File speichern sollte. Ich müsste mir ein eigenes ISO basteln. Das kann ich aber nicht. Ich müsste an die Entwickler herantreten. Wie das geht, weiß ich auch nicht.
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Willst Du Puppy in dem Fall nicht auf der Festplatte installieren? Dann kannst Du die xorg.conf wie bei jeder anderen Voll-Distribution ändern.
-----
Zugriff auf das iso wäre zur Not auch möglich.
https://wiki.archlinux.de/title/ISO-Image_mounten
-----
Zugriff auf das iso wäre zur Not auch möglich.
https://wiki.archlinux.de/title/ISO-Image_mounten
-
- Advanced Hacker
- Beiträge: 1091
- Registriert: 19. Jun 2008, 13:16
- Wohnort: Dettenhausen
- Kontaktdaten:
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Aufmerksam lesen hilft...
bhada hat geschrieben: ↑3. Feb 2018, 17:38[...] Problem mit der Installation von Puppy Slacko auf dem Notebook. Nachdem Einlesen der CD und Start von X bekomme ich nur einen weißen Bildschirm zu sehen. Grund ist, das der Bildschirm/ die Grafikarte mit 1024x768 Pixel nur eine Bildwiederholrate von maximal 60 Hz zulässt Puppy Slacko aber stets 75 Hz einstellt. Ich finde keine Möglichkeit, diese Einstellung zu ändern. [...]
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Ja, und? Ich gehe natürlich davon aus, daß er (neben dem Uralt-Toshiba seiner Frau) noch ein zweites System hat (mit dem er hier auch auf das Forum zugreift). Da kopiert er sich einfach das Puppy-ISO auf die Festplatte, mountet das ISO, ändert die xorg.conf und brennt sich davon eine neue CD. Damit bootet er dann das Toshiba.marce hat geschrieben: ↑7. Feb 2018, 07:46Aufmerksam lesen hilft...bhada hat geschrieben: ↑3. Feb 2018, 17:38[...] Problem mit der Installation von Puppy Slacko auf dem Notebook. Nachdem Einlesen der CD und Start von X bekomme ich nur einen weißen Bildschirm zu sehen. Grund ist, das der Bildschirm/ die Grafikarte mit 1024x768 Pixel nur eine Bildwiederholrate von maximal 60 Hz zulässt Puppy Slacko aber stets 75 Hz einstellt. Ich finde keine Möglichkeit, diese Einstellung zu ändern. [...]
Das Puppy-ISO ist kleiner als 300 MB. Wo ist das Problem?
-
- Advanced Hacker
- Beiträge: 1091
- Registriert: 19. Jun 2008, 13:16
- Wohnort: Dettenhausen
- Kontaktdaten:
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Na, dann ist diese Formulierung aber mehr als missverständlich.
Ich deute die nämlich so, daß Du ihm empfiehlst, die Installation durchzuführen und dann die xorg.conf zu ändern...
Abgesehen davon ist das Abändern der ISO nicht einfach nur durch "ISO mounten, eine Datei darin abändern, ISO unmounten" erledigt...
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Was soll er Deiner Meinung nach also tun?
-
- Advanced Hacker
- Beiträge: 1091
- Registriert: 19. Jun 2008, 13:16
- Wohnort: Dettenhausen
- Kontaktdaten:
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Zuerst mal könnte er posten, was denn das Toshiba exakt für ein Modell ist.
Ich würde als nächstes versuchen, wenn das Ding mit dem internen Monitor nicht will, halt einen externen anschließen, damit die Installation durchzuführen und dann die Konfig so zu ändern, daß der interne auch wieder will.
Zudem - wenn ich vermute - gibt's in http://slacko.eezy.xyz/notes.php einen Hinweis auf die (vermutlich verbaute - geraten aus der xorg.conf) Grafikkarte und was man dabei denn tun soll.
Die einfachste Variante wäre vermutlich das Ding zu entsorgen und für kleines Geld ein brauchbares, aktuelles Consumer-Notebook zu beschaffen. Spart einem viel Streß, man kann Distris verwenden, für die es auch eine ordentliche User-Basis gibt und ist für die nächsten 10 Jahre fein raus bis man dann wieder hier steht mit einem ähnlichen Problem.
Ich würde als nächstes versuchen, wenn das Ding mit dem internen Monitor nicht will, halt einen externen anschließen, damit die Installation durchzuführen und dann die Konfig so zu ändern, daß der interne auch wieder will.
Zudem - wenn ich vermute - gibt's in http://slacko.eezy.xyz/notes.php einen Hinweis auf die (vermutlich verbaute - geraten aus der xorg.conf) Grafikkarte und was man dabei denn tun soll.
Die einfachste Variante wäre vermutlich das Ding zu entsorgen und für kleines Geld ein brauchbares, aktuelles Consumer-Notebook zu beschaffen. Spart einem viel Streß, man kann Distris verwenden, für die es auch eine ordentliche User-Basis gibt und ist für die nächsten 10 Jahre fein raus bis man dann wieder hier steht mit einem ähnlichen Problem.
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Neue Hardware ...
Neue Hardware ...
"Kauf' Dir doch ein Fertignotebook mit Windows" wäre vielleicht auch ein Ratschlag. Ich gehe lieber erstmal von dem aus, was der Fragesteller offenbar hat.
Allerdings gibt es mehrere Puppy-Versionen. Vielleicht könnte er noch eine andere versuchen, nicht die, die auf Slackware aufbaut. Oder einfach 'ne OpenSuSE.
Zuletzt geändert von abgdf am 8. Feb 2018, 17:45, insgesamt 1-mal geändert.
-
- Advanced Hacker
- Beiträge: 1091
- Registriert: 19. Jun 2008, 13:16
- Wohnort: Dettenhausen
- Kontaktdaten:
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Na, den Monitor kann er doch leihweise vom oben erwähnten Desktop nehmen - ich bin mir recht sicher, daß da einer dranhängt.
(wobei Du gehst ja nur davon aus, daß er einen 2. PC hat - bereits geschriebenes des TE ist dir ja irgendwie meist egal)
Aber lassen wir das. Also wir beide meine ich.
(wobei Du gehst ja nur davon aus, daß er einen 2. PC hat - bereits geschriebenes des TE ist dir ja irgendwie meist egal)
Aber lassen wir das. Also wir beide meine ich.
Re: Installation Puppy Slacko 6.3.2 auf einem alten Toshiba Notebook
Entschuldigt das lange ausbleiben meiner Meldung. Habe viel andere Termine gehabt und kam nicht dazu.
Ich will es nun erst einmal mit einem externen Bildschirm versuchen, Puppy Slacko installieren und dann die xorg.conf ändern. Mal sehen ob das klappt.
Ich will es nun erst einmal mit einem externen Bildschirm versuchen, Puppy Slacko installieren und dann die xorg.conf ändern. Mal sehen ob das klappt.