Kann mal jemand, der die Daten zu interpretieren weiß, die selbigen durchschauen:
Code:
# smartctl --all /dev/sda5
smartctl 5.39 2009-08-08 r2872~ [i686-pc-linux-gnu] (openSUSE RPM)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG SV8004H
Serial Number: 0453J1FT802388
Firmware Version: QR100-12
User Capacity: 80.060.424.192 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 1
Local Time is: Tue Jan 19 21:21:34 2010 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (3120) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 16) minutes.
SMART Attributes Data Structure revision number: 9
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 692
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3398
5 Reallocated_Sector_Ct 0x0033 253 253 009 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1766298
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1723
194 Temperature_Celsius 0x0022 160 124 000 Old_age Always - 26
197 Current_Pending_Sector 0x0033 253 253 009 Pre-fail Always - 0
198 Offline_Uncorrectable 0x0031 253 253 009 Pre-fail Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0
201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0
SMART Error Log Version: 1
Warning: ATA error count 173 inconsistent with error log pointer 1
ATA Error Count: 173 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 173 occurred at disk power-on lifetime: 14717 hours (613 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 05 01 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 15 05 01 00 00 a0 00 00:00:06.000 IDENTIFY PACKET DEVICE
ec 15 05 01 00 00 b0 00 00:00:06.000 IDENTIFY DEVICE
a1 15 05 01 00 00 b0 00 00:00:05.000 IDENTIFY PACKET DEVICE
b0 d9 f1 00 4f c2 a0 00 00:00:05.000 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 00 00:00:05.000 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
Error 172 occurred at disk power-on lifetime: 14717 hours (613 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 05 01 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 14 05 01 00 00 a0 00 00:00:05.000 IDENTIFY PACKET DEVICE
ec 14 05 01 00 00 b0 00 00:00:05.000 IDENTIFY DEVICE
a1 14 05 01 00 00 b0 00 00:00:05.000 IDENTIFY PACKET DEVICE
b0 d9 f1 00 4f c2 a0 00 00:00:04.000 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 00 00:00:04.000 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
Error 171 occurred at disk power-on lifetime: 14717 hours (613 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 05 01 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 15 05 01 00 00 a0 00 00:00:04.000 IDENTIFY PACKET DEVICE
ec 15 05 01 00 00 b0 00 00:00:04.000 IDENTIFY DEVICE
a1 15 05 01 00 00 b0 00 00:00:04.000 IDENTIFY PACKET DEVICE
b0 d5 01 01 4f c2 00 00 49d+09:37:51.296 SMART READ LOG
b0 d5 01 06 4f c2 00 00 49d+09:37:51.296 SMART READ LOG
Error 170 occurred at disk power-on lifetime: 14707 hours (612 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 05 01 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 05 01 00 00 a0 00 00:00:06.000 IDENTIFY PACKET DEVICE
ec 00 05 01 00 00 b0 00 00:00:06.000 IDENTIFY DEVICE
a1 00 05 01 00 00 b0 00 00:00:06.000 IDENTIFY PACKET DEVICE
b0 d9 f1 00 4f c2 a0 00 00:18:43.000 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 00 00:18:43.000 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
Error 169 occurred at disk power-on lifetime: 14707 hours (612 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 88 05 01 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d5 01 01 4f c2 00 00 01:19:51.000 SMART READ LOG
b0 d1 01 01 4f c2 00 00 01:19:51.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
b0 d0 01 00 4f c2 00 00 01:19:51.000 SMART READ DATA
b0 da 00 00 4f c2 00 00 01:19:51.000 SMART RETURN STATUS
b0 da 00 00 4f c2 00 00 01:19:51.000 SMART RETURN STATUS
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 14718 -
Device does not support Selective Self Tests/Logging