Nach Neustart knetworkmanager immer deaktiviert

## Path:	Network/General
## Description:	Set some general network configuration
## Type:	string("","-","+")
## Default:	"+"
## ServiceRestart: network
#
# DEFAULT_BROADCAST is used when no individual BROADCAST is set. It can get one
# of the following values:
# ""  : don't set a broadcast address
# "-" : use IPADDR with all host bits deleted
# "+" : use IPADDR with all host bits set
DEFAULT_BROADCAST="+"

## Type:	yesno
## Default:	yes
# sometimes we want some script to be executed after an interface has been
# brought up, or before an interface is taken down. 
# default dir is /etc/sysconfig/network/if-up.d for POST_UP and
# /etc/sysconfig/network/if-down.d for PRE_DOWN
# Note: if you use NetworkManager then down scripts will be called after the
# interface is down and not before.
GLOBAL_POST_UP_EXEC="yes"
GLOBAL_PRE_DOWN_EXEC="yes"

## Type:        yesno
## Default:     no
# If ifup should check if an ip address is already in use, set this to yes.
# Make sure that packet sockets (CONFIG_PACKET) are supported in the kernel,
# since this feature uses arping, which depends on that.
# Also be aware that this takes one second per interface; consider that when
# setting up a lot of interfaces. 
CHECK_DUPLICATE_IP="no"

## Type:        yesno
## Default:     no
# Switch on/off debug messages for all network configuration stuff. If set to no
# most scripts can enable it locally with "-o debug".
DEBUG="no"

## Type:        yesno
## Default:     yes
# All error and info messages from network and hardware configuration scripts go
# to stderr. Most tools that call sysconfig scripts (udev, rcnetwork, scpm,
# YaST) catch these messages and can log them. So some messages appear twice in
# syslog. If you don't like that, then set USE_SYSLOG=no.
USE_SYSLOG="yes"

# Handling of network connections
# ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
# These features are designed for the convenience of the experienced
# user. If you encounter problems you don't understand then switch
# them off. That is the default.
# Please do not complain if you get troubles. But if you want help to
# make them smarter write to <http://www.suse.de/feedback>.

## Type:	yesno
## Default:	no
#
# If you are interested in the connections and nfs mounts that use a
# network interface, you can set CONNECTION_SHOW_WHEN_IFSTATUS="yes".
# Then you will see them with 'ifstatus <interface>' (or 'ifstatus
# <config>')
# This one _should_ never harm ;)
#
CONNECTION_SHOW_WHEN_IFSTATUS="no"

## Type:	yesno
## Default:	no
#
# If an interface should be set down only if there are no active
# connections, then use CONNECTION_CHECK_BEFORE_IFDOWN="yes"
#
CONNECTION_CHECK_BEFORE_IFDOWN="no"

## Type:	yesno
## Default:	no
#
# If these connetions (without the nfs mounts) should be closed when
# shutting down an interface, set CONNECTION_CLOSE_BEFORE_IFDOWN="yes".
# WARNING: Be aware that this may terminate applications which need
# one of these connections!
#
CONNECTION_CLOSE_BEFORE_IFDOWN="no"

## Type:	yesno
## Default:	no
#
# If you are a mobile laptop user and like even nfs mounts to be
# closed when you leave your current workplace, then set
# CONNECTION_UMOUNT_NFS_BEFORE_IFDOWN="yes". This does only work
# if CONNECTION_CLOSE_BEFORE_IFDOWN="yes", too.
# WARNING: Be aware that this may terminate applications which use
# these nfs mounts as working directory. Be very carefull if your home
# is mounted via nfs!!!
# WARNING: This may even lead to hanging ifdown processes if there are
# processes that could not be terminated. If you are using
# hotpluggable devices (pcmcia, usb, firewire), first shut them down
# before unplugging!
#
CONNECTION_UMOUNT_NFS_BEFORE_IFDOWN="no"

## Type:	yesno
## Default:	no
#
# If terminating processes that use a connection or nfs mount is not
# enough, then they can be killed after an unsuccesfull termination.
# If you want that set CONNECTION_SEND_KILL_SIGNAL="yes"
#
CONNECTION_SEND_KILL_SIGNAL="no"

## Type:        string
## Default:     ""
#
# Here you may specify which interfaces have to be up and configured properly
# after 'rcnetwork start'. rcconfig will return 'failed' if any of these
# interfaces is not up. You may use interface names as well but better use
# hardware descriptions of the devices (eth-id-<macaddress> or eth-bus-...  See
# man ifup for 'hardware description'). The network start script will wait for
# these interfaces, but not longer as set in WAIT_FOR_INTERFACES.
# You need not to add dialup or tunnel interfaces here, only physical devices.
# The interface 'lo' is always considered to be mandatory and can be omitted.
#
# If this variable is empty, rcnetwork tries to derive the list of mandatory
# devices automatically from the list of existing configurations. Configurations
# with names bus-pcmcia or bus-usb or with STARTMODE=hotplug are skipped. (try
# '/etc/init.d/rc5.d/S*network start -o debug fake | grep MANDAT')
MANDATORY_DEVICES=""

## Type:	integer
## Default:	30
#
# Some interfaces need some time to come up or come asynchronously via hotplug.
# WAIT_FOR_INTERFACES is a global wait for all mandatory interfaces in
# seconds. If empty no wait occurs.
#
WAIT_FOR_INTERFACES="30"

## Type:	yesno
## Default:	yes
#
# With this variable you can determine if the SuSEfirewall when enabled
# should get started when network interfaces are started.
FIREWALL="yes"

## Type:        string
## Default:     "eth*[0-9]|tr*[0-9]|wlan[0-9]|ath[0-9]"
#
# Automatically add a linklocal route to the matching interfaces.
# This string is used in a bash "case" statement, so it may contain
# '*', '[', ']'  and '|' meta-characters.
#
LINKLOCAL_INTERFACES="eth*[0-9]|tr*[0-9]|wlan[0-9]|ath[0-9]"

## Type:        string
## Default:     "-f -I"
#
# Set default options for ifplugd. You may also set them in an ifcfg-* file
# individually. Have a look at 'man ifplug' for details. We let ifplugd set the
# interface UP when starting, because there are many interfaces where link beat
# cannot be detected otherwise. If you want the interface to stay down then add
# the option '-a'. If you like ifplugd to beep on cable (un)plug, remove '-b'.
#
IFPLUGD_OPTIONS="-f -I -b"

## Type:        yesno
## Default:     no
#
# Instead of the usual network setup (now called 'NetControl') you may also use
# 'NetworkManager' to control your interfaces.
#
# NetControl is what you were used to in SUSE Linux up to now. It has a wide
# range of configurations means for setting up any number of different virtual
# and real interfaces. It should be used if you:
# - want a static network setup
# - have many interfaces
# - need VLAN, bonding, bridging, multiple IP addresses
# - must restrict network control to root
# It may also switch interfaces automatically, but lacks a usable GUI for normal
# users.
#
# NetworkManager lets the user control interfaces and switches automatically if
# network interfaces lose/gain physical connection. It should be used if you:
# - move between networks frequently
# - want a GUI for network control
# Especially on mobile computers that use mainly one wired and one wireless
# interface NetworkManager will please you.
#
# If you are used to SCPM then you might probably stay with NetControl. But at
# least try NetworkManager, because it can replace SCPM in some usage scenarios.
# 
NETWORKMANAGER="yes"

## Type:	int
## Default:	0
#
# When using NetworkManager you may define a timeout to wait for NetworkManager
# to connect.  Other network services may require the system to have a valid
# network setup in order to succeed.
# 
# This variable has no effect if NETWORKMANAGER=no
#
NM_ONLINE_TIMEOUT="0"

## Type:        string
## Default:     "dns-resolver dns-bind ntp-runtime nis"
#
# This variable defines the start order of netconfig modules installed
# in the /etc/netconfig.d/ directory.
#
# To disable the execution of a module, don't remove it from the list
# but prepend it with a minus sign, "-ntp-runtime".
#
NETCONFIG_MODULES_ORDER="dns-resolver dns-bind dns-dnsmasq nis ntp-runtime"

## Type:        string
## Default:     "auto"
#
# Defines the DNS merge policy as documented in netconfig(8) manual page.
# Set to "" to disable DNS configuration.
#
NETCONFIG_DNS_POLICY="auto"

## Type:        string
## Default:     "resolver"
#
# Defines the name of the DNS forwarder that has to be configured.
#
NETCONFIG_DNS_FORWARDER="resolver"

## Type:        string
## Default:     ""
#
# List of DNS domain names used for host-name lookup.
#
NETCONFIG_DNS_STATIC_SEARCHLIST=""

## Type:        string
## Default:     ""
#
# List of DNS nameserver IP addresses to use for host-name lookup.
#
NETCONFIG_DNS_STATIC_SERVERS=""

## Type:        string
## Default:     "auto"
#
# Defines the NTP merge policy as documented in netconfig(8) manual page.
# Set to "" to disable NTP configuration.
#
NETCONFIG_NTP_POLICY="auto"

## Type:        string
## Default:     ""
#
# List of NTP servers.
#
NETCONFIG_NTP_STATIC_SERVERS=""

## Type:        string
## Default:     "auto"
#
# Defines the NIS merge policy as documented in netconfig(8) manual page.
# Set to "" to disable NIS configuration.
#
NETCONFIG_NIS_POLICY="auto"

## Type:        string
## Default:     "yes"
#
# Defines whether to set the default NIS domain. When enabled and no domain
# is provided dynamically or in static settings, /etc/defaultdomain is used.
# Valid values are:
#  - "no" or ""         netconfig does not set the domainname
#  - "yes"              netconfig sets the domainname according to the
#                       NIS policy using settings provided by the first
#                       iterface and service that provided it.
#  - "<interface name>" as yes, but only using settings from interface.
#
NETCONFIG_NIS_SETDOMAINNAME="yes"

## Type:        string
## Default:     ""
#
# Defines a default NIS domain.
#
# Further domain can be specified by adding a "_<number>" suffix to
# the NETCONFIG_NIS_STATIC_DOMAIN and NETCONFIG_NIS_STATIC_SERVERS
# variables, e.g.: NETCONFIG_NIS_STATIC_DOMAIN_1="second".
#
NETCONFIG_NIS_STATIC_DOMAIN=""

## Type:        string
## Default:     ""
#
# Defines a list of NIS servers for the default NIS domain or the
# domain specified with same "_<number>" suffix.
#
NETCONFIG_NIS_STATIC_SERVERS=""

## Type:	string
## Default:	''
#
# Set this variable to the ISO / IEC 3166 alpha2 country code
# specifying the wireless regulatory domain to set.
# When not-empty, it will be set in the wpa_supplicant config
# or via 'iw reg set' command.
#
# Note: in wpa_supplicant mode, it is currently (openSUSE 11.2)
# not supported by our default 'wext', but by the new 'nl80211'
# wpa driver. You can set WIRELESS_WPA_DRIVER='nl80211' in the
# per interface ifcfg config file. We will switch to use the
# new driver as soon as we've tested it with more chipsets.
#
WIRELESS_REGULATORY_DOMAIN=''

cat /etc/sysconfig/network/config | egrep -v "(^#.*|^$)"

DEFAULT_BROADCAST="+"                                                  
GLOBAL_POST_UP_EXEC="yes"                                              
GLOBAL_PRE_DOWN_EXEC="yes"                                             
CHECK_DUPLICATE_IP="no"                                                
DEBUG="no"                                                             
USE_SYSLOG="yes"
CONNECTION_SHOW_WHEN_IFSTATUS="no"
CONNECTION_CHECK_BEFORE_IFDOWN="no"
CONNECTION_CLOSE_BEFORE_IFDOWN="no"
CONNECTION_UMOUNT_NFS_BEFORE_IFDOWN="no"
CONNECTION_SEND_KILL_SIGNAL="no"
MANDATORY_DEVICES=""
WAIT_FOR_INTERFACES="30"
FIREWALL="yes"
LINKLOCAL_INTERFACES="eth*[0-9]|tr*[0-9]|wlan[0-9]|ath[0-9]"
IFPLUGD_OPTIONS="-f -I -b"
NETWORKMANAGER="yes"
NM_ONLINE_TIMEOUT="0"
NETCONFIG_MODULES_ORDER="dns-resolver dns-bind dns-dnsmasq nis ntp-runtime"
NETCONFIG_DNS_POLICY="auto"
NETCONFIG_DNS_FORWARDER="resolver"
NETCONFIG_DNS_STATIC_SEARCHLIST=""
NETCONFIG_DNS_STATIC_SERVERS=""
NETCONFIG_NTP_POLICY="auto"
NETCONFIG_NTP_STATIC_SERVERS=""
NETCONFIG_NIS_POLICY="auto"
NETCONFIG_NIS_SETDOMAINNAME="yes"
NETCONFIG_NIS_STATIC_DOMAIN=""
NETCONFIG_NIS_STATIC_SERVERS=""
WIRELESS_REGULATORY_DOMAIN=''