Hallo!
Nachdem ich den Faxversand erfolgreich konfiguriert habe, mache ich mich gerade an den Empfang:
Leider hebt mein Modem aber nicht automatisch ab. Ich habe etwas von einem "Ring befehl" gelesen verstehe aber nicht wo ich diesen verwenden kann. Eigentlich sollte doch (das Modem läutet ja! mgetty läuft! ) mgetty automatisch abgheben. Woran könnte das liegen? Bin für jeden Tipp dankbar! Hier mal die mgetty.config:
Besten Dank an alle! Habe auch google bemüht... Leider gibts mehr Infos zu Hylafax.... Habe nichts gefunden....
Gruss Alex
Nachdem ich den Faxversand erfolgreich konfiguriert habe, mache ich mich gerade an den Empfang:
Leider hebt mein Modem aber nicht automatisch ab. Ich habe etwas von einem "Ring befehl" gelesen verstehe aber nicht wo ich diesen verwenden kann. Eigentlich sollte doch (das Modem läutet ja! mgetty läuft! ) mgetty automatisch abgheben. Woran könnte das liegen? Bin für jeden Tipp dankbar! Hier mal die mgetty.config:
Habe da keinen Eintrag fürs Abheben gefunden.# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
# comment lines start with a "#", empty lines are ignored
# ----- global section -----
#
# In this section, you put the global defaults, per-port stuff is below
# set the global debug level to "4" (default from policy.h)
debug 4
# set the local fax station id
fax-id 49 69 53098544
# access the modem(s) with 38400 bps
speed 38400
# use these options to make the /dev/tty-device owned by "uucp.uucp"
# and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!*
port-owner uucp
port-group uucp
port-mode 0664
# use these options to make incoming faxes owned by "root.uucp"
# and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!*
fax-owner root
fax-group uucp
fax-mode 0640
# ----- port specific section -----
#
# Here you can put things that are valid only for one line, not the others
#
# Zoom V.FX 28.8, connected to ttyS0: don't do fax, less logging
#
port ttyS0
# debug 3
# data-only y
# some other Rockwell modem, needs "switchbd 19200" to receive faxes
# properly (otherwise it will fail with "timeout").
#
#port ttyS1
# speed 38400
# switchbd 19200
# ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics
#
#port ttyS2
# debug 8
# init-chat "" \d\d\d+++\d\d\dAT&FS2=255 OK ATN3S0=0S13.2=1 OK
# statistics-chat "" AT OK ATI2 OK
# statistics-file /var/log/statistics.ttyS2
# modem-type cls2
# direct connection of a VT100 terminal which doesn't like DTR drops
# ("direct" meaning "*no* *modem*". NEVER enable "direct yes" on modem lines!)
#
#port ttyS3
# direct y
# speed 19200
# toggle-dtr n
Besten Dank an alle! Habe auch google bemüht... Leider gibts mehr Infos zu Hylafax.... Habe nichts gefunden....
Gruss Alex