Bootvorgang dauert sehr lange

Hi,

seit einiger Zeit brauch mein Rechner sehr lange zum booten. Immer wenn Suse beim Booten von dem ersten Bildschirm (wenn man dort Esc drückt sieht man was er anstellt) zum 2.Bildschirm (KDE wird gestartet wechselt bleibt er dazwischen ca. 20 Sekunden mit einem schwarzen Kreuz stehen. Das war vor ein paar Tagen noch nicht so lange.

Mein var/log/messages vom Bootvorgang, bringt auch deutlich zu viele Fehlermeldungen:

Dec 10 06:32:06 linux syslog-ng[4065]: syslog-ng version 1.6.8 starting
Dec 10 06:32:08 linux syslog-ng[4065]: Changing permissions on special file /dev/xconsole
Dec 10 06:32:08 linux syslog-ng[4065]: Changing permissions on special file /dev/tty10
Dec 10 06:32:08 linux mDNSResponder (Engineering Build) (Sep 9 2005 15:59:08) [4557]: starting
Dec 10 06:32:08 linux mDNSResponder: Unable to parse DNS server list. Unicast DNS-SD unavailable
Dec 10 06:32:08 linux modify_resolvconf: Service smpppd-ifcfg modified /etc/resolv.conf. See info block in this file
Dec 10 06:32:09 linux pppd[4598]: Plugin rp-pppoe.so loaded.
Dec 10 06:32:09 linux pppd[4598]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3
Dec 10 06:32:10 linux pppd[4598]: Plugin passwordfd.so loaded.
Dec 10 06:32:10 linux /usr/sbin/cron[4861]: (CRON) STARTUP (V5.0)
Dec 10 06:32:10 linux pppd[4598]: pppd 2.4.3 started by root, uid 0
Dec 10 06:32:10 linux pppd[4598]: Renamed interface ppp0 to dsl0
Dec 10 06:32:10 linux pppd[4598]: Using interface dsl0
Dec 10 06:32:10 linux pppd[4598]: Couldn't increase MTU to 1500
Dec 10 06:32:10 linux pppd[4598]: Couldn't increase MRU to 1500
Dec 10 06:32:10 linux pppd[4598]: local IP address 192.168.99.1
Dec 10 06:32:10 linux pppd[4598]: remote IP address 192.168.99.99
Dec 10 06:32:10 linux ifup: No configuration found for sit0
Dec 10 06:32:11 linux kernel: klogd 1.4.1, log source = /proc/kmsg started.
Dec 10 06:32:11 linux kernel: parport: PnPBIOS parport detected.
Dec 10 06:32:11 linux kernel: parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
Dec 10 06:32:11 linux kernel: lp0: using parport0 (interrupt-driven).
Dec 10 06:32:11 linux kernel: NET: Registered protocol family 10
Dec 10 06:32:11 linux kernel: Disabled Privacy Extensions on device c036b920(lo)
Dec 10 06:32:11 linux kernel: IPv6 over IPv4 tunneling driver
Dec 10 06:32:11 linux kernel: ip6_tables: (C) 2000-2002 Netfilter core team
Dec 10 06:32:11 linux kernel: ip_tables: (C) 2000-2002 Netfilter core team
Dec 10 06:32:11 linux kernel: ip_conntrack version 2.1 (8191 buckets, 65528 max) - 248 bytes per conntrack
Dec 10 06:32:11 linux kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Dec 10 06:32:11 linux kernel: shpchp: shpc_init : shpc_cap_offset == 0
Dec 10 06:32:11 linux kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Dec 10 06:32:11 linux kernel: Linux agpgart interface v0.101 (c) Dave Jones
Dec 10 06:32:11 linux kernel: agpgart: Detected SiS 746 chipset
Dec 10 06:32:11 linux kernel: agpgart: AGP aperture is 64M @ 0xd0000000
Dec 10 06:32:11 linux kernel: i2c-sis96x version 1.0.0
Dec 10 06:32:11 linux kernel: sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
Dec 10 06:32:11 linux kernel: sis900.c: v1.08.08 Jan. 22 2005
Dec 10 06:32:11 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
Dec 10 06:32:11 linux kernel: PCI: setting IRQ 11 as level-triggered
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Dec 10 06:32:11 linux kernel: 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
Dec 10 06:32:11 linux kernel: 0000:00:04.0: Using transceiver found at address 1 as default
Dec 10 06:32:11 linux kernel: eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 11, 00:0b:6a:14:cc:48.
Dec 10 06:32:11 linux kernel: usbcore: registered new driver usbfs
Dec 10 06:32:11 linux kernel: usbcore: registered new driver hub
Dec 10 06:32:11 linux kernel: ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 3
Dec 10 06:32:11 linux kernel: PCI: setting IRQ 3 as level-triggered
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 3 (level, low) -> IRQ 3
Dec 10 06:32:11 linux kernel: ohci_hcd 0000:00:03.0: OHCI Host Controller
Dec 10 06:32:11 linux kernel: ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
Dec 10 06:32:11 linux kernel: ohci_hcd 0000:00:03.0: irq 3, io mem 0xcfffd000
Dec 10 06:32:11 linux kernel: hub 1-0:1.0: USB hub found
Dec 10 06:32:11 linux kernel: hub 1-0:1.0: 3 ports detected
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
Dec 10 06:32:11 linux kernel: PCI: setting IRQ 5 as level-triggered
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt 0000:00:03.1 -> Link [LNKF] -> GSI 5 (level, low) -> IRQ 5
Dec 10 06:32:11 linux kernel: ohci_hcd 0000:00:03.1: OHCI Host Controller
Dec 10 06:32:11 linux kernel: ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
Dec 10 06:32:11 linux kernel: ohci_hcd 0000:00:03.1: irq 5, io mem 0xcfffe000
Dec 10 06:32:11 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
Dec 10 06:32:11 linux kernel: PCI: setting IRQ 10 as level-triggered
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
Dec 10 06:32:11 linux kernel: hub 2-0:1.0: USB hub found
Dec 10 06:32:11 linux kernel: hub 2-0:1.0: 3 ports detected
Dec 10 06:32:11 linux kernel: usb 1-2: new low speed USB device using ohci_hcd and address 2
Dec 10 06:32:11 linux kernel: bcm3510: module not supported by Novell, setting U taint flag.
Dec 10 06:32:11 linux kernel: b2c2_flexcop: module not supported by Novell, setting U taint flag.
Dec 10 06:32:11 linux kernel: b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Dec 10 06:32:11 linux kernel: b2c2_flexcop_pci: module not supported by Novell, setting U taint flag.
Dec 10 06:32:11 linux kernel: intel8x0_measure_ac97_clock: measured 54891 usecs
Dec 10 06:32:11 linux kernel: intel8x0: clocking to 48000
Dec 10 06:32:11 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 12
Dec 10 06:32:11 linux kernel: PCI: setting IRQ 12 as level-triggered
Dec 10 06:32:11 linux kernel: ACPI: PCI Interrupt 0000:00:03.2[D] -> Link [LNKH] -> GSI 12 (level, low) -> IRQ 12
Dec 10 06:32:11 linux kernel: ehci_hcd 0000:00:03.2: EHCI Host Controller
Dec 10 06:32:11 linux kernel: ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
Dec 10 06:32:11 linux kernel: ehci_hcd 0000:00:03.2: irq 12, io mem 0xcffff000
Dec 10 06:32:11 linux kernel: PCI: cache line size of 64 is not supported by device 0000:00:03.2
Dec 10 06:32:12 linux kernel: ehci_hcd 0000:00:03.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
Dec 10 06:32:12 linux kernel: hub 3-0:1.0: USB hub found
Dec 10 06:32:12 linux kernel: hub 3-0:1.0: 6 ports detected
Dec 10 06:32:12 linux kernel: usb 1-2: unable to read config index 0 descriptor/start
Dec 10 06:32:12 linux kernel: usb 1-2: can't read configurations, error -110
Dec 10 06:32:12 linux kernel: flexcop-pci: will use the HW PID filter.
Dec 10 06:32:12 linux kernel: flexcop-pci: card revision 2
Dec 10 06:32:12 linux kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Dec 10 06:32:12 linux kernel: ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Dec 10 06:32:12 linux kernel: DVB: registering new adapter (FlexCop Digital TV device).
Dec 10 06:32:12 linux kernel: b2c2-flexcop: MAC address = 00:d0:d7:0c:d4:f3
Dec 10 06:32:12 linux kernel: b2c2-flexcop: found the stv0299 at i2c address: 0x68
Dec 10 06:32:12 linux kernel: DVB: registering frontend 0 (ST STV0299 DVB-S)...
Dec 10 06:32:12 linux kernel: b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
Dec 10 06:32:12 linux kernel: usb 1-2: new low speed USB device using ohci_hcd and address 4
Dec 10 06:32:12 linux kernel: usbcore: registered new driver hiddev
Dec 10 06:32:12 linux kernel: input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:03.0-2
Dec 10 06:32:12 linux kernel: usbcore: registered new driver usbhid
Dec 10 06:32:12 linux kernel: drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Dec 10 06:32:12 linux kernel: bootsplash: status on console 0 changed to on
Dec 10 06:32:12 linux kernel: BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Dec 10 06:32:12 linux kernel: ACPI: Power Button (FF) [PWRF]
Dec 10 06:32:12 linux kernel: ACPI: Power Button (CM) [PWRB]
Dec 10 06:32:12 linux kernel: IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
Dec 10 06:32:12 linux kernel: IA-32 Microcode Update Driver v1.14 unregistered
Dec 10 06:32:12 linux kernel: eth0: Media Link On 100mbps full-duplex
Dec 10 06:32:12 linux kernel: CSLIP: code copyright 1989 Regents of the University of California
Dec 10 06:32:12 linux kernel: PPP generic driver version 2.4.2
Dec 10 06:32:12 linux kernel: NET: Registered protocol family 17
Dec 10 06:32:12 linux kernel: powernow-k8: Processor cpuid 6a0 not supported
Dec 10 06:32:12 linux rcpowersaved: CPU frequency scaling is not supported by your processor.
Dec 10 06:32:12 linux rcpowersaved: enter 'CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/cpufreq to avoid this warning.
Dec 10 06:32:12 linux rcpowersaved: Cannot load cpufreq governors - No cpufreq driver available
Dec 10 06:32:13 linux [powersave]: ERROR (CPUFreq_Kernel:21) Can not set ondemand governor, maybe your cpufreq driver is too slow.
Dec 10 06:32:13 linux [powersave]: ERROR (CPUFreq_Kernel:23) Try CPUFREQ_CONTROL=userspace in /etc/sysconfig/powersave/cpufreq.
Dec 10 06:32:13 linux [powersave]: ERROR (PM_Interface:231) Cannot create cpufreq objects

Was stimmt hier nicht?

mal gemacht was da steht?

Auch in dieser Fehlermeldung haben wir wieder eine kleine Mus für Sie versteckt ...
Ich nehme an, Gimpel meint das hier:

Waschbaer schrieb:

Dec 10 06:32:11 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
(...)
Dec 10 06:32:12 linux kernel: powernow-k8: Processor cpuid 6a0 not supported
Dec 10 06:32:12 linux rcpowersaved: CPU frequency scaling is not supported by your processor.
Dec 10 06:32:12 linux rcpowersaved: enter 'CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/cpufreq to avoid this warning.
Dec 10 06:32:12 linux rcpowersaved: Cannot load cpufreq governors - No cpufreq driver available

Zum Vergrößern anklicken....

Also wohl eindeutig ein Problem mit der Energiekontrolle. ACPI abschalten, oder, falls das möglich ist, den fraglichen Treiber nachinstallieren, oder eben /etc/sysconfig/powersave/cpufreq editieren.

Hi, hat ein bisschen länger gedauert

wenn ich das hier mache:
CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/cpufreq to avoid this warning
Try CPUFREQ_CONTROL=userspace in /etc/sysconfig/powersave/cpufreq

Kommen noch mehr Fehlermeldungen:
Dec 11 21:39:32 linux [powersave]: ERROR (CPUFreq_Userspace:42) Could not set userspace governor, seems as if the cpufreq_userspace module is not loaded.
Dec 11 21:39:32 linux [powersave]: ERROR (read_line:43) Could not open file for reading: '/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies'
Dec 11 21:39:32 linux [powersave]: ERROR (read_line:43) Could not open file for reading: '/sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq'
Dec 11 21:39:32 linux [powersave]: ERROR (read_value:82) Could not read value in file /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq: error: No such file or directory!
Dec 11 21:39:32 linux [powersave]: ERROR (read_line:43) Could not open file for reading: '/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq'
Dec 11 21:39:32 linux [powersave]: ERROR (read_value:82) Could not read value in file /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq: error: No such file or directory!
Dec 11 21:39:32 linux [powersave]: WARNING (getMinMaxSpeeds:349) Speedstepping not supported! Was the correct cpufreq module loaded?
Dec 11 21:39:32 linux [powersave]: WARNING (initFreqsViaTesting:377) Could not read min and max speed
Dec 11 21:39:32 linux [powersave]: ERROR (PM_Interface:231) Cannot create cpufreq objects


Ich habe die Änderungen wieder rückgängig gemacht, jetzt kommt aber jedesmal beim Start von KDE:

Der powersave-Daemon läuft nicht.

Durch Starten desselben verbessert sich die Leistung: /usr/sbin/rcpowersaved start