• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

(gelöst)Anstatt Loginscreen nur schwarzer Bildschirm

Hallo zusammen
Ich bin was Linux anbelangt leider noch relativ neu.
Hab nun auf meinem Laptop Modell Samsung R40 T5500 Chinoso Open Suse 11.1 installiert.
Die Installation lief auch problemlos und alles funktionierte bestens.
Als ich heute morgen jedoch den Laptop starten wollte kam nach normalem Bootvorgang anstatt der Loginscreen nur ein schwarzer Bildschirm.
Ich hoffe mir kann jemand helfen
 

lOtz1009

Moderator
Teammitglied
Hast du irgendwas vor dem letzten Start verändert?
Probier mal: http://www.linupedia.org/opensuse/Schwarzer_Bildschirm_-_Grafische_Oberfl%C3%A4che_startet_nicht
 
OP
Capt Chronic

Capt Chronic

Newbie
lOtz schrieb:
Hast du irgendwas vor dem letzten Start verändert?

Nein eben nicht deswegen wundert mich das ja auch so
Was villeicht noch intressant ist hab als zweites bs auf dem Laptop Winxp laufen da is alles ohene probleme.
 
OP
Capt Chronic

Capt Chronic

Newbie
Nein
Ich habe wie im Link von dir beschrieben während des splashscreens F2 dann3 eingegeben nach dem splashscreen blieb der Bildschirm wieterhin schwarz.
Hab das ganze dann nochma nur mit 3 gemacht mit dem selben ergebnis
Soll heißen konnte mich nach wie vor nicht anmelden.
 

Curryfrosch

Member
Tut sich etwas, wenn Du ab dem Moment, wo der Bildschirm schwarz wird, mal Strg+Alt+F1 bis Strg+Alt+F12 durchprobierst?
 

Curryfrosch

Member
Nicht gut. Das sieht erst mal so aus, als hätte Linux massive Probleme mit der Grafikkarte. Siehst Du vorher irgendwelche Meldungen die weiterhelfen könnten (ESC drücken falls statt Systemmeldungen Grafik angezeigt wird)?
 
OP
Capt Chronic

Capt Chronic

Newbie
So hier boot.msg
Code:
Inspecting /boot/System.map-2.6.27.23-0.1-pae
Cannot find map file.
No module symbols loaded - kernel modules not enabled.

Cannot build symbol table - disabling symbol lookups
klogd 1.4.1, log source = ksyslog started.
<6>Initializing cgroup subsys cpuset
<6>Initializing cgroup subsys cpu
<5>Linux version 2.6.27.23-0.1-pae (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2009-05-26 17:02:05 -0400
<6>BIOS-provided physical RAM map:
<6> BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
<6> BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
<6> BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
<6> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
<6> BIOS-e820: 0000000000100000 - 0000000037e90000 (usable)
<6> BIOS-e820: 0000000037e90000 - 0000000037ea3000 (ACPI data)
<6> BIOS-e820: 0000000037ea3000 - 0000000037f00000 (ACPI NVS)
<6> BIOS-e820: 0000000037f00000 - 0000000038000000 (reserved)
<6> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
<6> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
<6> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<6> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
<6>DMI present.
<5>Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
<6>last_pfn = 0x37e90 max_arch_pfn = 0x1000000
<6>x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
<7>kernel direct mapping tables up to 37e90000 @ 10000-19000
<6>RAMDISK: 3790b000 - 37e7f885
<4>ACPI: RSDP 000F7560, 0014 (r0 PTLTD )
<4>ACPI: RSDT 37E9E35C, 0034 (r1 PTLTD    RSDT    6040000  LTP        0)
<4>ACPI: FACP 37EA2EF2, 0074 (r1 SEC    FIRENZE2  6040000 SEC     F4240)
<4>ACPI: DSDT 37E9EE9D, 4055 (r1    ATI    SB450  6040000 INTL 20050228)
<4>ACPI: FACS 37EA3FC0, 0040
<4>ACPI: APIC 37EA2F66, 005E (r1 PTLTD  	 APIC    6040000  LTP        0)
<4>ACPI: MCFG 37EA2FC4, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
<4>ACPI: SSDT 37E9E390, 0535 (r1  PmRef    CpuPm     3000 INTL 20050228)
<5>ACPI: DMI detected: Samsung
<7>ACPI: Local APIC address 0xfee00000
<7>NUMA - single node, flat memory mode
<6>Node: 0, start_pfn: 0, end_pfn: 37e90
<7>  Setting physnode_map array to node 0 for pfns:
<7>  0 4000 8000 c000 10000 14000 18000 1c000 20000 24000 28000 2c000 30000 34000 
<7>node 0 pfn: [0 - 37e90]
<7>Reserving 2048 pages of KVA for lmem_map of node 0 at 37000
<7>remove_active_range (0, 225280, 227328)
<6>Reserving total of 800 pages for numa KVA remap
<6>kva_start_pfn ~ 36800 max_low_pfn ~ 37e90
<6>max_pfn = 37e90
<5>0MB HIGHMEM available.
<5>894MB LOWMEM available.
<7>max_low_pfn = 37e90, highstart_pfn = 37e90
<7>Low memory ends at vaddr f7e90000
<7>node 0 will remap to vaddr f6800000 - f7000000
<7>allocate_pgdat: node 0 NODE_DATA f6800000
<7>remap_numa_kva: node 0
<7>remap_numa_kva: f6800000 to pfn 00037000
<7>remap_numa_kva: f6a00000 to pfn 00037200
<7>remap_numa_kva: f6c00000 to pfn 00037400
<7>remap_numa_kva: f6e00000 to pfn 00037600
<7>High memory starts at vaddr f7e90000
<6>  mapped low ram: 0 - 37e90000
<6>  low ram: 00000000 - 37e90000
<6>  bootmap 00015000 - 0001bfd4
<6>(11 early reservations) ==> bootmem [0000000000 - 0037e90000]
<6>  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
<6>  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
<6>  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
<6>  #3 [0000100000 - 000065445c]    TEXT DATA BSS ==> [0000100000 - 000065445c]
<6>  #4 [003790b000 - 0037e7f885]          RAMDISK ==> [003790b000 - 0037e7f885]
<6>  #5 [0000655000 - 000065d000]    INIT_PG_TABLE ==> [0000655000 - 000065d000]
<6>  #6 [000009dc00 - 0000100000]    BIOS reserved ==> [000009dc00 - 0000100000]
<6>  #7 [0000010000 - 0000015000]          PGTABLE ==> [0000010000 - 0000015000]
<6>  #8 [0037000000 - 0037800000]          KVA RAM ==> [0037000000 - 0037800000]
<6>  #9 [0036800000 - 0037000000]           KVA PG ==> [0036800000 - 0037000000]
<6>  #10 [0000015000 - 000001c000]          BOOTMAP ==> [0000015000 - 000001c000]
<6>found SMP MP-table at [c00f7590] 000f7590
<4>Zone PFN ranges:
<4>  DMA      0x00000010 -> 0x00001000
<4>  Normal   0x00001000 -> 0x00037e90
<4>  HighMem  0x00037e90 -> 0x00037e90
<4>Movable zone start PFN for each node
<4>early_node_map[3] active PFN ranges
<4>    0: 0x00000010 -> 0x0000009d
<4>    0: 0x00000100 -> 0x00037000
<4>    0: 0x00037800 -> 0x00037e90
<7>On node 0 totalpages: 226845
<7>free_area_init_node: node 0, pgdat f6800000, node_mem_map f6802240
<7>  DMA zone: 3945 pages, LIFO batch:0
<7>  Normal zone: 220887 pages, LIFO batch:31
<6>Using APIC driver default
<6>SB4X0 revision 0x83
<6>Ignoring ACPI timer override.
<6>If you got timer trouble try acpi_use_timer_override
<6>ACPI: PM-Timer IO Port: 0x8008
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
<6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<6>IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
<4>Enabling APIC mode:  Flat.  Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<6>SMP: Allowing 2 CPUs, 0 hotplug CPUs
<7>mapped APIC to ffffb000 (fee00000)
<7>mapped IOAPIC to ffffa000 (fec00000)
<6>PM: Registered nosave memory: 000000000009d000 - 000000000009e000
<6>PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
<6>PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
<6>PM: Registered nosave memory: 00000000000dc000 - 00000000000e0000
<6>PM: Registered nosave memory: 00000000000e0000 - 00000000000e4000
<6>PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
<6>Allocating PCI resources starting at 40000000 (gap: 38000000:a8000000)
<6>PERCPU: Allocating 38556 bytes of per cpu data
<7>NR_CPUS: 128, nr_cpu_ids: 2, nr_node_ids 8
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 224832
<4>Policy zone: Normal
<5>Kernel command line: root=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 resume=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part2 splash=silent vga=0x314
<6>bootsplash: silent mode.
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 16384 bytes)
<6>TSC: PIT calibration confirmed by PMTIMER.
<6>TSC: using PIT calibration value
<4>Detected 1666.706 MHz processor.
<4>Console: colour dummy device 80x25
<6>console [tty0] enabled
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Initializing HighMem for node 0 (00000000:00000000)
<6>Memory: 887184k/916032k available (2358k kernel code, 28388k reserved, 1930k data, 292k init, 0k highmem)
<6>virtual kernel memory layout:
<6>    fixmap  : 0xff8b7000 - 0xfffff000   (7456 kB)
<6>    pkmap   : 0xff400000 - 0xff600000   (2048 kB)
<6>    vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
<6>    lowmem  : 0xc0000000 - 0xf7e90000   ( 894 MB)
<6>      .init : 0xc0539000 - 0xc0582000   ( 292 kB)
<6>      .data : 0xc034d8f5 - 0xc05301d0   (1930 kB)
<6>      .text : 0xc0100000 - 0xc034d8f5   (2358 kB)
<6>Checking if this processor honours the WP bit even in supervisor mode...Ok.
<7>CPA: page pool initialized 1 of 1 pages preallocated
<6>Calibrating delay loop (skipped), value calculated using timer frequency.. 3333.41 BogoMIPS (lpj=6666824)
<4>kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved
<6>Security Framework initialized
<6>AppArmor: AppArmor initialized
<4>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys ns
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys memory
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>CPU: L1 I cache: 32K, L1 D cache: 32K
<6>CPU: L2 cache: 2048K
<6>CPU: Physical Processor ID: 0
<6>CPU: Processor Core ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<6>using mwait in idle threads.
<6>Checking 'hlt' instruction... OK.
<6>ACPI: Core revision 20080609
<6>ACPI: Checking initramfs for custom DSDT
<4>Parsing all Control Methods:
<4>Table [DSDT](id 0001) - 571 Objects with 54 Devices 179 Methods 25 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0002) - 13 Objects with 0 Devices 4 Methods 0 Regions
<4> tbxface-0596 [00] tb_load_namespace     : ACPI Tables successfully acquired
<4>evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
<6>Mapping cpu 0 to node 0
<4>ENABLING IO-APIC IRQs
<6>..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
<6>CPU0: Intel(R) Core(TM)2 CPU         T5500  @ 1.66GHz stepping 06
<6>Booting processor 1/1 ip 6000
<6>Initializing CPU#1
<6>Mapping cpu 1 to node 0
<6>Calibrating delay using timer specific routine.. 3333.73 BogoMIPS (lpj=6667460)
<6>CPU: L1 I cache: 32K, L1 D cache: 32K
<6>CPU: L2 cache: 2048K
<6>CPU: Physical Processor ID: 0
<6>CPU: Processor Core ID: 1
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#1.
<6>x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
<6>CPU1: Intel(R) Core(TM)2 CPU         T5500  @ 1.66GHz stepping 06
<6>checking TSC synchronization [CPU#0 -> CPU#1]: passed.
<6>Brought up 2 CPUs
<6>Total of 2 processors activated (6667.14 BogoMIPS).
<7>CPU0 attaching sched-domain:
<7> domain 0: span 0-1 level MC
<7>  groups: 0 1
<7>  domain 1: span 0-1 level NODE
<7>   groups: 0-1
<7>CPU1 attaching sched-domain:
<7> domain 0: span 0-1 level MC
<7>  groups: 1 0
<7>  domain 1: span 0-1 level NODE
<7>   groups: 0-1
<6>net_namespace: 1044 bytes
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<5>PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 4
<5>PCI: MCFG area at e0000000 reserved in E820
<6>PCI: Using MMCONFIG for extended config space
<6>PCI: Using configuration type 1 for base access
<5>perfmon: version 2.82
<5>perfmon: CPU hotplug support enabled
<4>evgpeblk-0957 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x15
<7>ACPI: EC: Look up EC in DSDT
<4>Completing Region/Field/Buffer/Package initialization:.....................................................
<4>Initialized 21/25 Regions 0/0 Fields 14/14 Buffers 18/18 Packages (593 nodes)
<4>Initializing Device/Processor/Thermal objects by executing _INI methods:......
<4>Executed 6 _INI methods requiring 0 _STA executions (examined 59 objects)
<4>evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 0 Runtime GPEs in this block
<6>ACPI: Interpreter enabled
<6>ACPI: (supports S0 S3 S4 S5)
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: EC: non-query interrupt received, switching to interrupt mode
<6>ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62
<6>ACPI: EC: driver started in interrupt mode
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<7>PCI: 0000:00:13.0 reg 10 32bit mmio: [c0404000, c0404fff]
<7>PCI: 0000:00:13.1 reg 10 32bit mmio: [c0405000, c0405fff]
<7>PCI: 0000:00:13.2 reg 10 32bit mmio: [c0406000, c0406fff]
<7>pci 0000:00:13.2: supports D1
<7>pci 0000:00:13.2: supports D2
<6>pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
<6>pci 0000:00:13.2: PME# disabled
<7>PCI: 0000:00:14.0 reg 10 io port: [8400, 840f]
<7>PCI: 0000:00:14.0 reg 14 32bit mmio: [c0407000, c04073ff]
<6>HPET not enabled in BIOS. You might try hpet=force boot option
<7>PCI: 0000:00:14.1 reg 10 io port: [8428, 842f]
<7>PCI: 0000:00:14.1 reg 14 io port: [8434, 8437]
<7>PCI: 0000:00:14.1 reg 18 io port: [8420, 8427]
<7>PCI: 0000:00:14.1 reg 1c io port: [8430, 8433]
<7>PCI: 0000:00:14.1 reg 20 io port: [8410, 841f]
<7>PCI: 0000:00:14.2 reg 10 64bit mmio: [c0400000, c0403fff]
<6>pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
<6>pci 0000:00:14.2: PME# disabled
<7>PCI: 0000:01:05.0 reg 10 32bit mmio: [d0000000, dfffffff]
<7>PCI: 0000:01:05.0 reg 14 io port: [9000, 90ff]
<7>PCI: 0000:01:05.0 reg 18 32bit mmio: [c0000000, c000ffff]
<7>PCI: 0000:01:05.0 reg 30 32bit mmio: [0, 1ffff]
<7>pci 0000:01:05.0: supports D1
<7>pci 0000:01:05.0: supports D2
<7>PCI: bridge 0000:00:01.0 io port: [9000, 9fff]
<7>PCI: bridge 0000:00:01.0 32bit mmio: [c0000000, c00fffff]
<7>PCI: bridge 0000:00:01.0 32bit mmio pref: [d0000000, dfffffff]
<7>PCI: 0000:02:07.0 reg 10 32bit mmio: [c0100000, c010ffff]
<7>PCI: 0000:02:09.0 reg 10 32bit mmio: [c0110000, c0110fff]
<7>pci 0000:02:09.0: supports D1
<7>pci 0000:02:09.0: supports D2
<6>pci 0000:02:09.0: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:02:09.0: PME# disabled
<7>PCI: 0000:02:09.1 reg 10 32bit mmio: [c0111000, c01110ff]
<7>pci 0000:02:09.1: supports D1
<7>pci 0000:02:09.1: supports D2
<6>pci 0000:02:09.1: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:02:09.1: PME# disabled
<7>PCI: 0000:02:09.2 reg 10 32bit mmio: [c0111400, c01114ff]
<7>pci 0000:02:09.2: supports D1
<7>pci 0000:02:09.2: supports D2
<6>pci 0000:02:09.2: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:02:09.2: PME# disabled
<7>PCI: 0000:02:09.3 reg 10 32bit mmio: [c0111800, c01118ff]
<7>pci 0000:02:09.3: supports D1
<7>pci 0000:02:09.3: supports D2
<6>pci 0000:02:09.3: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:02:09.3: PME# disabled
<7>PCI: 0000:02:09.4 reg 10 32bit mmio: [c0111c00, c0111cff]
<7>pci 0000:02:09.4: supports D1
<7>pci 0000:02:09.4: supports D2
<6>pci 0000:02:09.4: PME# supported from D0 D1 D2 D3hot D3cold
<6>pci 0000:02:09.4: PME# disabled
<6>pci 0000:00:14.4: transparent bridge
<7>PCI: bridge 0000:00:14.4 32bit mmio: [f0200000, f02fffff]
<7>PCI: bridge 0000:00:14.4 32bit mmio pref: [f0300000, f03fffff]
<7>bus 00 -> node 0
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
<6>ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
<6>ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
<6>ACPI: Power Resource [FN00] (off)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>ACPI: bus type pnp registered
<4>pnp 00:09: mem resource (0x0-0xfff) overlaps 0000:01:05.0 BAR 6 (0x0-0x1ffff), disabling
<6>pnp: PnP ACPI: found 10 devices
<6>ACPI: ACPI bus type pnp unregistered
<6>PnPBIOS: Disabled by ACPI PNP
<6>PCI: Using ACPI for IRQ routing
<6>AppArmor: AppArmor Filesystem Enabled
<6>system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
<6>system 00:08: ioport range 0x1080-0x1080 has been reserved
<6>system 00:08: ioport range 0x220-0x22f has been reserved
<6>system 00:08: ioport range 0x40b-0x40b has been reserved
<6>system 00:08: ioport range 0x4d0-0x4d1 has been reserved
<6>system 00:08: ioport range 0x4d6-0x4d6 has been reserved
<6>system 00:08: ioport range 0x530-0x537 has been reserved
<6>system 00:08: ioport range 0xc00-0xc01 has been reserved
<6>system 00:08: ioport range 0xc14-0xc14 has been reserved
<6>system 00:08: ioport range 0xc50-0xc52 has been reserved
<6>system 00:08: ioport range 0xc6c-0xc6c has been reserved
<6>system 00:08: ioport range 0xc6f-0xc6f has been reserved
<6>system 00:08: ioport range 0xcd4-0xcd5 has been reserved
<6>system 00:08: ioport range 0xcd6-0xcd7 has been reserved
<6>system 00:08: ioport range 0xcd8-0xcdf has been reserved
<6>system 00:08: ioport range 0x8000-0x805f has been reserved
<6>system 00:08: ioport range 0x8210-0x821f has been reserved
<6>system 00:08: ioport range 0xf40-0xf47 has been reserved
<6>system 00:08: ioport range 0x280-0x293 has been reserved
<6>system 00:08: ioport range 0x87f-0x87f has been reserved
<6>system 00:09: iomem range 0xe0000-0xfffff could not be reserved
<6>system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
<6>pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
<6>pci 0000:00:01.0:   IO window: 0x9000-0x9fff
<6>pci 0000:00:01.0:   MEM window: 0xc0000000-0xc00fffff
<6>pci 0000:00:01.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
<6>pci 0000:02:09.0: CardBus bridge, secondary bus 0000:03
<6>pci 0000:02:09.0:   IO window: 0x002000-0x0020ff
<6>pci 0000:02:09.0:   IO window: 0x002400-0x0024ff
<6>pci 0000:02:09.0:   PREFETCH window: 0x40000000-0x43ffffff
<6>pci 0000:02:09.0:   MEM window: 0x44000000-0x47ffffff
<6>pci 0000:00:14.4: PCI bridge, secondary bus 0000:02
<6>pci 0000:00:14.4:   IO window: 0x2000-0x2fff
<6>pci 0000:00:14.4:   MEM window: 0xf0200000-0xf02fffff
<6>pci 0000:00:14.4:   PREFETCH window: 0x000000f0300000-0x000000f03fffff
<6>pci 0000:02:09.0: power state changed by ACPI to D0
<6>vendor=1002 device=4371
<6>pci 0000:02:09.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
<6>bus: 00 index 0 io port: [0, ffff]
<6>bus: 00 index 1 mmio: [0, ffffffffffffffff]
<6>bus: 01 index 0 io port: [9000, 9fff]
<6>bus: 01 index 1 mmio: [c0000000, c00fffff]
<6>bus: 01 index 2 mmio: [d0000000, dfffffff]
<6>bus: 01 index 3 mmio: [0, 0]
<6>bus: 02 index 0 io port: [2000, 2fff]
<6>bus: 02 index 1 mmio: [f0200000, f02fffff]
<6>bus: 02 index 2 mmio: [f0300000, f03fffff]
<6>bus: 02 index 3 io port: [0, ffff]
<6>bus: 02 index 4 mmio: [0, ffffffffffffffff]
<6>bus: 03 index 0 io port: [2000, 20ff]
<6>bus: 03 index 1 io port: [2400, 24ff]
<6>bus: 03 index 2 mmio: [40000000, 43ffffff]
<6>bus: 03 index 3 mmio: [44000000, 47ffffff]
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>Unpacking initramfs... done
<6>Freeing initrd memory: 5586k freed
<6>Machine check exception polling timer started.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(1247419202.656:1): initialized
<6>HugeTLB registered 2 MB page size, pre-allocated 0 pages
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>msgmni has been set to 435
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>perfmon: added sampling format default
<7>pci 0000:01:05.0: Boot video device
<6>vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3750k, total 16384k
<6>vesafb: mode is 800x600x16, linelength=1600, pages=16
<6>vesafb: protected mode interface info at c000:5497
<6>vesafb: pmi: set display start = c00c5505, set palette = c00c553f
<6>vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 
<6>vesafb: scrolling: redraw
<6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<6>bootsplash 3.1.6-2004/03/31: looking for picture...
<6>bootsplash: silentjpeg size 82170 bytes
<6>bootsplash: ...found (800x600, 31893 bytes, v3).
<4>Console: switching to colour frame buffer device 96x33
<6>fb0: VESA VGA frame buffer device
<6>isapnp: Scanning for PnP cards...
<7>Switched to high resolution mode on CPU 1
<7>Switched to high resolution mode on CPU 0
<6>isapnp: No Plug & Play device found
<6>Serial: 8250/16550 driver8 ports, IRQ sharing enabled
<6>PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
<6>i8042.c: Detected active multiplexing controller, rev 1.1.
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>serio: i8042 AUX0 port at 0x60,0x64 irq 12
<6>serio: i8042 AUX1 port at 0x60,0x64 irq 12
<6>serio: i8042 AUX2 port at 0x60,0x64 irq 12
<6>serio: i8042 AUX3 port at 0x60,0x64 irq 12
<6>mice: PS/2 mouse device common for all mice
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
<6>TCP cubic registered
<4>Using IPI No-Shortcut mode
<4>registered taskstats version 1
<6>Freeing unused kernel memory: 292k freed
<6>Write protecting the kernel text: 2360k
<6>Write protecting the kernel read-only data: 1748k
<6>input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
<4>ACPI: SSDT 37E9EBC5, 0251 (r1  PmRef  Cpu0Ist     3000 INTL 20050228)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0074) - 5 Objects with 0 Devices 3 Methods 0 Regions
<4>ACPI: SSDT 37E9E8C5, 027B (r1  PmRef  Cpu0Cst     3001 INTL 20050228)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0075) - 6 Objects with 0 Devices 1 Methods 0 Regions
<6>processor ACPI_CPU:00: registered as cooling_device0
<6>ACPI: Processor [CPU0] (supports 8 throttling states)
<4>ACPI: SSDT 37E9EE16, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20050228)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0079) - 3 Objects with 0 Devices 3 Methods 0 Regions
<4>ACPI: SSDT 37E9EB40, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20050228)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 007A) - 1 Objects with 0 Devices 1 Methods 0 Regions
<6>processor ACPI_CPU:01: registered as cooling_device1
<6>ACPI: Processor [CPU1] (supports 8 throttling states)
<6>thermal LNXTHERM:01: registered as thermal_zone0
<6>ACPI: Thermal Zone [TZ00] (55 C)
<6>ACPI: No dock devices found.
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
<7>pata_atiixp 0000:00:14.1: setting latency timer to 64
<6>scsi0 : pata_atiixp
<6>scsi1 : pata_atiixp
<6>ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8410 irq 14
<6>ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8418 irq 15
<4>ata1.00: failed to set max address (err_mask=0x1)
<4>ata1.00: device aborted resize (180468192 -> 195371568), skipping HPA handling
<6>ata1.00: ATA-6: HTS541010G9AT00, MBZOA60A, max UDMA/100
<6>ata1.00: 180468192 sectors, multi 16: LBA48 
<6>ata1.00: configured for UDMA/100
<6>ata2.00: ATAPI: TSSTcorpCD/DVDW TS-L632D, SC02, max UDMA/33
<6>ata2.00: configured for UDMA/33
<5>scsi 0:0:0:0: Direct-Access     ATA      HTS541010G9AT00  MBZO PQ: 0 ANSI: 5
<5>scsi 1:0:0:0: CD-ROM            TSSTcorp CD/DVDW TS-L632D SC02 PQ: 0 ANSI: 5
<6>Uniform Multi-Platform E-IDE driver
<6>fan PNP0C0B:00: registered as cooling_device2
<6>ACPI: Fan [FAN0] (on)
<6>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
<6>udevd version 128 started
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<6>ohci_hcd 0000:00:13.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
<6>ohci_hcd 0000:00:13.0: OHCI Host Controller
<6>ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
<6>ohci_hcd 0000:00:13.0: irq 19, io mem 0xc0404000
<5>sd 0:0:0:0: [sda] 180468192 512-byte hardware sectors: (92.3GB/86.0GiB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<4>Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 0:0:0:0: [sda] 180468192 512-byte hardware sectors: (92.3GB/86.0GiB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1 sda2 sda3
<5>sd 0:0:0:0: [sda] Attached SCSI disk
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 4 ports detected
<6>Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x200000
<6>input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input1
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: OHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.27.23-0.1-pae ohci_hcd
<6>usb usb1: SerialNumber: 0000:00:13.0
<6>ohci_hcd 0000:00:13.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
<6>ohci_hcd 0000:00:13.1: OHCI Host Controller
<6>ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
<6>ohci_hcd 0000:00:13.1: irq 19, io mem 0xc0405000
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 4 ports detected
<6>usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: OHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.27.23-0.1-pae ohci_hcd
<6>usb usb2: SerialNumber: 0000:00:13.1
<6>ehci_hcd 0000:00:13.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
<6>ehci_hcd 0000:00:13.2: EHCI Host Controller
<6>ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
<6>ehci_hcd 0000:00:13.2: irq 19, io mem 0xc0406000
<6>ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 8 ports detected
<6>usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: EHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.27.23-0.1-pae ehci_hcd
<6>usb usb3: SerialNumber: 0000:00:13.2
<6>PM: Starting manual resume from disk
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on sda3, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>udevd version 128 started
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>scsi 1:0:0:0: Attached scsi generic sg1 type 5
<6>input: PC Speaker as /devices/platform/pcspkr/input/input2
<4>sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<7>sr 1:0:0:0: Attached scsi CD-ROM sr0
<6>Linux agpgart interface v0.103
<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
<6>ACPI: AC Adapter [ADP1] (on-line)
<6>ACPI: Power Button (FF) [PWRF]
<6>input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
<6>ACPI: Power Button (CM) [PWRB]
<6>input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
<6>ACPI: Lid Switch [LID0]
<6>input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
<6>ACPI: Sleep Button (CM) [SLPB]
<6>ACPI: Battery Slot [BAT1] (battery present)
<6>ricoh-mmc: Ricoh MMC Controller disabling driver
<6>ricoh-mmc: Copyright(c) Philip Langdale
<6>ricoh-mmc: Ricoh MMC controller found at 0000:02:09.2 [1180:0843] (rev 0)
<6>ricoh-mmc: Controller is now disabled.
<6>input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:16/device:17/input/input7
<6>Yenta: CardBus bridge found at 0000:02:09.0 [144d:c02b]
<6>sdhci: Secure Digital Host Controller Interface driver
<6>sdhci: Copyright(c) Pierre Ossman
<6>ACPI: Video Device [ATIM] (multi-head: yes  rom: no  post: no)
<6>rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
<6>rtc0: alarms up to one month
<6>Yenta: ISA IRQ mask 0x0eb8, PCI irq 20
<6>Socket status: 30000006
<6>pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
<6>cs: IO port probe 0x2000-0x2fff: clean.
<6>pcmcia: parent PCI bridge Memory window: 0xf0200000 - 0xf02fffff
<6>pcmcia: parent PCI bridge Memory window: 0xf0300000 - 0xf03fffff
<6>piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8400, revision 0
<6>HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
<6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>hda_codec: Unknown model for ALC262, trying auto-probe from BIOS...
<7>ALSA sound/pci/hda/hda_codec.c:3188: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0)
<7>ALSA sound/pci/hda/hda_codec.c:3192:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<7>ALSA sound/pci/hda/hda_codec.c:3196:    hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
<7>ALSA sound/pci/hda/hda_codec.c:3197:    mono: mono_out=0x0
<7>ALSA sound/pci/hda/hda_codec.c:3205:    inputs: mic=0x18, fmic=0x0, line=0x0, fline=0x0, cd=0x0, aux=0x0
<6>sdhci-pci 0000:02:09.1: SDHCI controller found [1180:0822] (rev 18)
<6>vendor=1002 device=4371
<6>sdhci-pci 0000:02:09.1: PCI INT C -> GSI 22 (level, low) -> IRQ 22
<6>mmc0: SDHCI controller on PCI [0000:02:09.1] using PIO
<4>fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
<6>[fglrx] Maximum main memory to use for locked dma buffers: 792 MBytes.
<6>[fglrx]   vendor: 1002 device: 5a62 count: 1
<6>[fglrx] ioport: bar 1, base 0x9000, size: 0x100
<6>vendor=1002 device=5a3f
<6>pci 0000:01:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
<6>[fglrx] Kernel PAT support detected, disabling driver built-in PAT support
<6>[fglrx] module loaded - fglrx 8.58.2 [Feb  4 2009] with 1 minors
<6>vendor=1002 device=4371
<6>ath5k_pci 0000:02:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
<6>ath5k_pci 0000:02:07.0: registered as 'phy0'
<7>phy0: Selected rate control algorithm 'pid'
<6>ath5k phy0: Atheros AR2413 chip found (MAC: 0x78, PHY: 0x45)
<6>cs: IO port probe 0x100-0x3af: clean.
<6>cs: IO port probe 0x3e0-0x4ff: clean.
<6>cs: IO port probe 0x820-0x8ff: clean.
<6>cs: IO port probe 0xc00-0xcf7: clean.
<6>cs: IO port probe 0xa00-0xaff: clean.
<6>Adding 1357484k swap on /dev/sda2.  Priority:-1 extents:1 across:1357484k
<6>device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
<6>loop: module loaded
<4>fuse init (API version 7.9)
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Sun Jul 12 17:20:04 2009

Trying manual resume from /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part2
Invoking userspace resume from /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part2
resume: libgcrypt version: 1.4.1
Trying manual resume from /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part2
Invoking in-kernel resume from /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part2
Waiting for device /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 to appear:  ok
fsck 1.41.1 (01-Sep-2008)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 
/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3: recovering journal
/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3: Clearing orphaned inode 2597583 (uid=0, gid=0, mode=0100600, size=217016)
/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3: clean, 176838/2637824 files, 1607005/10546672 blocks
fsck succeeded. Mounting root device read-write.
Mounting root /dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3

Boot logging started on /dev/tty1(/dev/console (deleted)) at Sun Jul 12 19:20:14 2009

done
Starting udevd: done
Loading drivers, configuring devices: done
Loading required kernel modules
doneActivating swap-devices in /etc/fstab...
doneSetting up the hardware clockdone
Activating device mapper...
done
Starting MD Raid unused
Checking file systems...
fsck 1.41.1 (01-Sep-2008)
donedone
Mounting local file systems...
/proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
$LogFile indicates unclean shutdown (0, 1)
Failed to mount '/dev/sda1': Die Operation wird nicht unterstützt
Mount is denied because NTFS is marked to be in use. Choose one action:

Choice 1: If you have Windows then disconnect the external devices by
          clicking on the 'Safely Remove Hardware' icon in the Windows
          taskbar then shutdown Windows cleanly.

Choice 2: If you don't have Windows then you can use the 'force' option for
          your own responsibility. For example type on the command line:

            mount -t ntfs-3g /dev/sda1 /windows/C -o force

    Or add the option to the relevant row in the /etc/fstab file:

            /dev/sda1 /windows/C ntfs-3g force 0 0
failedFuse filesystem already availabledone
Mounting fuse control filesystemdone
Setting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
fs.inotify.max_user_watches = 65536
net.ipv4.conf.default.promote_secondaries = 1
net.ipv4.conf.all.promote_secondaries = 1
done
Activating remaining swap-devices in /etc/fstab...
done<notice>killproc: kill(601,29)
Creating /var/log/boot.msg
doneMounting securityfs on /sys/kernel/security done
Loading AppArmor profiles Enabling syn flood protectiondone
Disabling IP forwardingdone
done
Setting up hostname 'linux-quzd'done
Setting up loopback interface     lo        
    lo        IP address: 127.0.0.1/8   
              IP address: 127.0.0.2/8   
done
done
System Boot Control: The system has been set up
Skipped features: boot.md boot.cycle
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(601,3)

INIT: 
Boot logging started on /dev/tty1(/dev/console) at Sun Jul 12 17:20:24 2009

Entering runlevel: 5


Master Resource Control: previous runlevel: N, switching to runlevel: 5
Starting syslog services<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin DO_CONFIRM= vga=0x314 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PWD=/ PREVLEVEL=N LINES=33 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin DO_CONFIRM= vga=0x314 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PWD=/ PREVLEVEL=N LINES=33 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/sbin/klogd ]
done
Starting D-Bus daemondone
Starting acpid <notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/sbin/acpid ]
done
Loading CPUFreq modulesdone
Starting HAL daemonInitializing random number generatordone
<notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/sbin/auditd ]
Mount CIFS File Systems unused
<notice>startproc: execve (/sbin/rpcbind) [ /sbin/rpcbind ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/sbin/rpcbind ]
Starting rpcbind done
Starting auditd done
done
Starting service kdm<notice>startproc: execve (/usr/bin/kdm) [ /usr/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin DO_CONFIRM= vga=0x314 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PWD=/ LANG=de_DE.UTF-8 PREVLEVEL=N LINES=33 QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ XCURSOR_THEME=DMZ WINDOWMANAGER=/usr/bin/startkde SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/usr/bin/kdm ]
done
Not starting NFS client services - no NFS found in /etc/fstab:unused
Loading console font lat9w-16.psfu  -m trivial G0:loadable
doneLoading keymap assuming iso-8859-15 euro
Loading /usr/share/kbd/keymaps/i386/qwertz/de-latin1-nodeadkeys.map.gz
doneLoading compose table latin1.adddone
Start Unicode mode
done<notice>checkproc: /usr/bin/kdm 2248
Starting java.binfmt_misc done
<notice>startproc: execve (/usr/sbin/NetworkManager) [ /usr/sbin/NetworkManager ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts DO_CONFIRM= vga=0x314 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PWD=/etc/sysconfig/network PREVLEVEL=N LINES=33 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManager ]
Starting Avahi daemon done
<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
Starting Name Service Cache Daemondone
<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ]
Starting the NetworkManagerdone
Starting cupsddone
Starting atieventsddone
Starting mail service (Postfix)<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
done
Starting smartd done
Starting SSH daemondone
Starting CRON daemon<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=96 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x314 DO_CONFIRM= RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-800x600.cfg PREVLEVEL=N LINES=33 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/ata-HTS541010G9AT00_MP20XAXLG1RTZS-part3 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
done
done
Master Resource Control: runlevel 5 has been reached
Skipped services in runlevel 5: smbfs nfs
<notice>killproc: kill(1885,3)

Hoff das bringt was
@Curryfrosch hab gesagt bin relativ neu mit Linux nicht mit Computern ;)
 

lOtz1009

Moderator
Teammitglied
Also den normalen Bootsplash nach GRUB siehst du noch?
Im Bootlog steht mal nichts was einen Hinweis auf defekte Grafik gibt.

Welche Grafikkarte steckt da drin? Zeig doch mal bitte deine /etc/X11/xorg.conf, /var/log/Xorg.0.log und die ~/.xsession-errors
 

Curryfrosch

Member
Capt Chronic schrieb:
hab gesagt bin relativ neu mit Linux nicht mit Computern ;)
Nicht jeder, der sich mit Computern auskennt, weiß was "boot.msg" für eine Datei ist und wo man sie findet. ;)

Tja, ich finde da erst mal auch nichts, sieht alles normal aus.

Hast Du mal im Bootmenü die Failsafe-Option ausgewählt statt "normalem" openSUSE?


@l0tz: Wenn auch keine Textkonsole geht, dürfte es doch eigentlich nicht an X liegen.
 
OP
Capt Chronic

Capt Chronic

Newbie
so hier die xorg.conf
Code:
# /.../
# SaX generated X11 config file
# Created on: 2009-07-10T17:39:56+0200.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax@suse.de>, 2005
# Contact: SaX-User list <https://lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#

Section "Files"
  FontPath     "/usr/share/fonts/misc:unscaled"
  FontPath     "/usr/share/fonts/local"
  FontPath     "/usr/share/fonts/75dpi:unscaled"
  FontPath     "/usr/share/fonts/100dpi:unscaled"
  FontPath     "/usr/share/fonts/Type1"
  FontPath     "/usr/share/fonts/URW"
  FontPath     "/usr/share/fonts/Speedo"
  FontPath     "/usr/share/fonts/PEX"
  FontPath     "/usr/share/fonts/cyrillic"
  FontPath     "/usr/share/fonts/latin2/misc:unscaled"
  FontPath     "/usr/share/fonts/latin2/75dpi:unscaled"
  FontPath     "/usr/share/fonts/latin2/100dpi:unscaled"
  FontPath     "/usr/share/fonts/latin2/Type1"
  FontPath     "/usr/share/fonts/latin7/75dpi:unscaled"
  FontPath     "/usr/share/fonts/baekmuk:unscaled"
  FontPath     "/usr/share/fonts/japanese:unscaled"
  FontPath     "/usr/share/fonts/kwintv"
  FontPath     "/usr/share/fonts/truetype"
  FontPath     "/usr/share/fonts/uni:unscaled"
  FontPath     "/usr/share/fonts/CID"
  FontPath     "/usr/share/fonts/ucs/misc:unscaled"
  FontPath     "/usr/share/fonts/ucs/75dpi:unscaled"
  FontPath     "/usr/share/fonts/ucs/100dpi:unscaled"
  FontPath     "/usr/share/fonts/hellas/misc:unscaled"
  FontPath     "/usr/share/fonts/hellas/75dpi:unscaled"
  FontPath     "/usr/share/fonts/hellas/100dpi:unscaled"
  FontPath     "/usr/share/fonts/hellas/Type1"
  FontPath     "/usr/share/fonts/misc/sgi:unscaled"
  FontPath     "/usr/share/fonts/xtest"
  FontPath     "/opt/kde3/share/fonts"
  InputDevices "/dev/gpmdata"
  InputDevices "/dev/input/mice"
EndSection

Section "ServerFlags"
  Option       "AllowMouseOpenFail" "on"
  Option       "ZapWarning" "on"
EndSection

Section "Module"
  Load         "freetype"
  Load         "dbe"
  Load         "dri"
  Load         "glx"
  Load         "extmod"
EndSection

Section "InputDevice"
  Driver       "kbd"
  Identifier   "Keyboard[0]"
  Option       "Protocol" "Standard"
  Option       "XkbLayout" "de"
  Option       "XkbModel" "microsoftpro"
  Option       "XkbRules" "xfree86"
  Option       "XkbVariant" "nodeadkeys"
EndSection


Section "InputDevice"
  Driver       "synaptics"
  Identifier   "Mouse[1]"
  Option       "Buttons" "5"
  Option       "Device" "/dev/input/mice"
  Option       "Emulate3Buttons" "on"
  Option       "HorizScrollDelta" "0"
  Option       "InputFashion" "Mouse"
  Option       "Name" "Synaptics;Touchpad"
  Option       "Protocol" "explorerps/2"
  Option       "SHMConfig" "on"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"
  Driver       "mouse"
  Identifier   "Mouse[3]"
  Option       "Buttons" "5"
  Option       "Device" "/dev/input/mice"
  Option       "Name" "ImPS/2 Generic Wheel Mouse"
  Option       "Protocol" "explorerps/2"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection


Section "Monitor"
  DisplaySize  305 230
  HorizSync    30-38
  Identifier   "Monitor[0]"
  ModelName    "800X600@60HZ"
  Option       "DPMS"
  Option       "PreferredMode" "1280x960"
  VendorName   "--> LCD"
  VertRefresh  30-61
  UseModes     "Modes[0]"
EndSection


Section "Modes"
  Identifier   "Modes[0]"
EndSection


Section "Screen"
  DefaultDepth 24
  SubSection "Display"
    Depth      15
    Modes      "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    3840 1200
  EndSubSection
  SubSection "Display"
    Depth      16
    Modes      "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    3840 1200
  EndSubSection
  SubSection "Display"
    Depth      24
    Modes      "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    3840 1200
  EndSubSection
  SubSection "Display"
    Depth      8
    Modes      "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    3840 1200
  EndSubSection
  Device       "Device[0]"
  Identifier   "Screen[0]"
  Monitor      "Monitor[0]"
EndSection


Section "Device"
  BoardName    "Radeon XPRESS 200M 5A62 (PCIE)"
  Driver       "radeon"
  Identifier   "Device[0]"
  Screen       0
  VendorName   "ATI"
EndSection



Section "ServerLayout"
  Identifier   "Layout[all]"
  InputDevice  "Keyboard[0]" "CoreKeyboard"
  InputDevice  "Mouse[1]" "CorePointer"
  InputDevice  "Mouse[3]" "SendCoreEvents"
  Option       "Clone" "off"
  Option       "Xinerama" "off"
  Screen       "Screen[0]"
EndSection


Section "DRI"
    Group      "video"
    Mode       0660
EndSection

Section "Extensions"
EndSection

und die xorg0.log
Code:
X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: openSUSE SUSE LINUX
Current Operating System: Linux linux-quzd 2.6.27.23-0.1-pae #1 SMP 2009-05-26 17:02:05 -0400 i686
Build Date: 27 February 2009  02:03:33PM
 
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Jul 12 18:00:37 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Layout[all]"
(**) |-->Screen "Screen[0]" (0)
(**) |   |-->Monitor "Monitor[0]"
(**) |   |-->Device "Device[0]"
(**) |-->Input Device "Keyboard[0]"
(**) |-->Input Device "Mouse[1]"
(**) |-->Input Device "Mouse[3]"
(**) Option "ZapWarning" "on"
(**) Option "AllowMouseOpenFail" "on"
(**) Option "Xinerama" "off"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/local" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/PEX" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/latin2/misc" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/latin2/75dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/latin2/100dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/latin2/Type1" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/latin7/75dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/baekmuk" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/japanese" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/kwintv" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/uni" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/CID" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/ucs/misc" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/ucs/75dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/ucs/100dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/hellas/misc" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/hellas/75dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/hellas/100dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/hellas/Type1" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/misc/sgi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/xtest" does not exist.
	Entry deleted from font path.
(==) Including the default font path /usr/share/fonts/misc:unscaled,/usr/share/fonts/TTF/,/usr/share/fonts/OTF,/usr/share/fonts/Type1/,/usr/share/fonts/100dpi:unscaled,/usr/share/fonts/75dpi:unscaled.
(**) FontPath set to:
	/usr/share/fonts/misc:unscaled,
	/usr/share/fonts/75dpi:unscaled,
	/usr/share/fonts/100dpi:unscaled,
	/usr/share/fonts/Type1,
	/usr/share/fonts/URW,
	/usr/share/fonts/Speedo,
	/usr/share/fonts/cyrillic,
	/usr/share/fonts/truetype,
	/opt/kde3/share/fonts,
	/usr/share/fonts/misc:unscaled,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF,
	/usr/share/fonts/Type1/,
	/usr/share/fonts/100dpi:unscaled,
	/usr/share/fonts/75dpi:unscaled
(**) Input device list set to "/dev/gpmdata,/dev/input/mice"
(==) ModulePath set to "/usr/lib/xorg/modules/updates,/usr/lib/xorg/modules"
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81f85c0
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.4
	X.Org Video Driver: 4.1
	X.Org XInput driver : 2.1
	X.Org Server Extension : 1.1
	X.Org Font Renderer : 0.6
(II) Loader running on linux
(++) using VT number 7

(--) PCI:*(0@1:5:0) unknown vendor (0x1002) unknown chipset (0x5a62) rev 0, Mem @ 0xd0000000/0, 0xc0000000/0, I/O @ 0x00009000/0, BIOS @ 0x????????/131072
(II) System resource ranges:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded by default.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "freetype"

(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
	compiled for 1.5.2, module version = 2.1.0
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "dbe"

(II) Loading /usr/lib/xorg/modules//extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"

(II) Loading /usr/lib/xorg/modules/updates//extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 7.4.0, module version = 1.0.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "glx"

(II) Loading /usr/lib/xorg/modules/updates//extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 7.4.0, module version = 1.0.0
(==) AIGLX disabled
(WW) fglrx: Force AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "extmod"

(II) Loading /usr/lib/xorg/modules//extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "record"

(II) Loading /usr/lib/xorg/modules//extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 1.1
(II) Loading extension RECORD
(II) LoadModule: "radeon"

(II) Loading /usr/lib/xorg/modules//drivers/radeon_drv.so
(II) Module radeon: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 4.3.0
	Module class: X.Org Video Driver
	ABI class: X.Org Video Driver, version 4.1
(II) LoadModule: "kbd"

(II) Loading /usr/lib/xorg/modules//input/kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.3.1
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(II) LoadModule: "synaptics"

(II) Loading /usr/lib/xorg/modules//input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 0.15.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(II) LoadModule: "mouse"

(II) Loading /usr/lib/xorg/modules//input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.3.0
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(II) RADEON: Driver for ATI Radeon chipsets:
	ATI Radeon Mobility X600 (M24) 3150 (PCIE),
	ATI Radeon Mobility X300 (M24) 3152 (PCIE),
	ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
	ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
	ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
	ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
	ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
	ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
	ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
	ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
	ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
	ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
	ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
	ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
	ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
	ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
	ATI Radeon X800PRO (R420) JI (AGP),
	ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
	ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
	ATI Radeon Mobility 9800 (M18) JN (AGP),
	ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
	ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
	ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
	ATI Radeon Mobility M7 LW (AGP),
	ATI Mobility FireGL 7800 M7 LX (AGP),
	ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
	ATI FireGL Mobility 9000 (M9) Ld (AGP),
	ATI Radeon Mobility 9000 (M9) Lf (AGP),
	ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
	ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
	ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
	ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
	ATI Radeon 9800XT NJ (AGP),
	ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
	ATI Radeon Mobility 9600 (M10) NQ (AGP),
	ATI Radeon Mobility 9600 (M11) NR (AGP),
	ATI Radeon Mobility 9600 (M10) NS (AGP),
	ATI FireGL Mobility T2 (M10) NT (AGP),
	ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
	ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
	ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
	ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
	ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
	ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
	ATI Radeon Mobility X300 (M22) 5460 (PCIE),
	ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
	ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
	ATI Radeon X800PRO (R423) UI (PCIE),
	ATI Radeon X800LE (R423) UJ (PCIE),
	ATI Radeon X800SE (R423) UK (PCIE),
	ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
	ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
	ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
	ATI FireGL unknown (R423) UR (PCIE),
	ATI FireGL unknown (R423) UT (PCIE),
	ATI Mobility FireGL V5000 (M26) (PCIE),
	ATI Mobility FireGL V5000 (M26) (PCIE),
	ATI Mobility Radeon X700 XL (M26) (PCIE),
	ATI Mobility Radeon X700 (M26) (PCIE),
	ATI Mobility Radeon X700 (M26) (PCIE),
	ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
	ATI Radeon Mobility 9100 IGP (U3) 5835,
	ATI Radeon XPRESS 200 5954 (PCIE),
	ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
	ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
	ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
	ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
	ATI Radeon XPRESS 200M 5975 (PCIE),
	ATI Radeon XPRESS 200 5A41 (PCIE),
	ATI Radeon XPRESS 200M 5A42 (PCIE),
	ATI Radeon XPRESS 200 5A61 (PCIE),
	ATI Radeon XPRESS 200M 5A62 (PCIE),
	ATI Radeon X300 (RV370) 5B60 (PCIE),
	ATI Radeon X600 (RV370) 5B62 (PCIE),
	ATI Radeon X550 (RV370) 5B63 (PCIE),
	ATI FireGL V3100 (RV370) 5B64 (PCIE),
	ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
	ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
	ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
	ATI Mobility Radeon X800 XT (M28) (PCIE),
	ATI Mobility FireGL V5100 (M28) (PCIE),
	ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
	ATI Radeon X850 XT PE (R480) (PCIE),
	ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
	ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
	ATI Radeon X850 XT (R480) (PCIE),
	ATI Radeon X800XT (R423) 5D57 (PCIE),
	ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
	ATI Radeon X700 PRO (RV410) (PCIE),
	ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
	ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
	ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
	ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
	ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
	ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
	ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
	ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
	ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
	ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
	ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
	ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
	ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
	ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
	ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
	ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
	ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
	ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
	ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
	ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
	ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
	ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
	ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
	ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
	ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
	ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
	ATI Mobility Radeon X1700, ATI Radeon X2300HD,
	ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
	ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
	ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
	ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
	ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
	ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
	ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
	ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI ATI FireGL V7400,
	ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
	ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
	ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
	ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
	ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
	ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
	ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600, ATI RV610,
	ATI Radeon HD 2400 XT, ATI Radeon HD 2400 Pro,
	ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000, ATI RV610,
	ATI ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
	ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610, ATI RV670,
	ATI Radeon HD3870, ATI Radeon HD3850, ATI RV670,
	ATI Radeon HD3870 X2, ATI FireGL V7700, ATI RV630,
	ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
	ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
	ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
	ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
	ATI FireGL V3600, ATI Radeon HD 2600 LE, ATI Radeon HD 3470,
	ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Mobility Radeon HD 3430,
	ATI Mobility Radeon HD 3400 Series, ATI FireMV 2450, ATI FireMV 2260,
	ATI FireMV 2260, ATI ATI Radeon HD 3600 Series,
	ATI ATI Radeon HD 3650 AGP, ATI ATI Radeon HD 3600 PRO,
	ATI ATI Radeon HD 3600 XT, ATI ATI Radeon HD 3600 PRO,
	ATI Mobility Radeon HD 3650, ATI Mobility Radeon HD 3670,
	ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
	ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics
(II) Primary Device is: PCI 01@00:05:0
(II) resource ranges after xf86ClaimFixedResources() call:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B]
	[5] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B]
	[6] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B]
	[7] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[8] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[9] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B]
	[10] 0	0	0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) RADEON(0): MMIO registers at 0x00000000c0000000: size 64KB
(II) RADEON(0): PCI bus 1 card 5 func 0
(**) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"

(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 0.1.0
	ABI class: X.Org Video Driver, version 4.1
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(--) RADEON(0): Chipset: "ATI Radeon XPRESS 200M 5A62 (PCIE)" (ChipID = 0x5a62)
(--) RADEON(0): Linear framebuffer at 0x00000000d0000000
(II) RADEON(0): PCI card detected
(II) Loading sub module "int10"
(II) LoadModule: "int10"

(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class: X.Org Video Driver, version 4.1
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(II) RADEON(0): Legacy BIOS detected
(II) RADEON(0): Direct rendering not officially supported on RN50/RC410/R600
(II) RADEON(0): Detected total video RAM=131072K, accessible=262144K (PCI BAR=262144K)
(--) RADEON(0): Mapped VideoRAM: 131072 kByte (128 bit DDR SDRAM)
(II) RADEON(0): Color tiling enabled by default
(II) RADEON(0): Max desktop size set to 3840x1200
(II) RADEON(0): For a larger or smaller max desktop size, add a Virtual line to your xorg.conf
(II) RADEON(0): If you are having trouble with 3D, reduce the desktop size by adjusting the Virtual line to your xorg.conf
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEON(0): ref_freq: 1432, min_out_pll: 20000, max_out_pll: 40000, min_in_pll: 100, max_in_pll: 1350, xclk: 26600, sclk: 266.000000, mclk: 300.000000
(II) RADEON(0): PLL parameters: rf=1432 rd=6 min=20000 max=40000; xclk=26600
(II) RADEON(0): Bios Connector table: 
(II) RADEON(0): Port0: DDCType-0x68, DACType-2, TMDSType-1, ConnectorType-1
(II) RADEON(0): Port4: DDCType-0x0, DACType-0, TMDSType-0, ConnectorType-7
(II) RADEON(0): Port5: DDCType-0x0, DACType-2, TMDSType-0, ConnectorType-5
(II) RADEON(0): Output VGA-0 using monitor section Monitor[0]
(**) RADEON(0): Option "PreferredMode" "1280x960"
(II) RADEON(0): I2C bus "VGA-0" initialized.
(II) RADEON(0): Output LVDS has no monitor section
(II) RADEON(0): Panel ID string: Samsung LTN154X1 WXGA   
(II) RADEON(0): Panel Size from BIOS: 1280x800
(II) RADEON(0): BIOS provided dividers will be used.
(WW) RADEON(0): LVDS Info:
XRes: 1280, YRes: 800, DotClock: 65320
HBlank: 64, HOverPlus: 8, HSyncWidth: 40
VBlank: 10, VOverPlus: 2, VSyncWidth: 3
(II) RADEON(0): Output S-video has no monitor section
(II) RADEON(0): Default TV standard: NTSC
(II) RADEON(0): TV standards supported by chip: NTSC PAL PAL-M NTSC-J 
(II) RADEON(0): Port0:
 Monitor   -- AUTO
 Connector -- VGA
 DAC Type  -- TVDAC/ExtDAC
 TMDS Type -- None
 DDC Type  -- 0x68
(II) RADEON(0): Port1:
 Monitor   -- AUTO
 Connector -- LVDS
 DAC Type  -- None
 TMDS Type -- None
 DDC Type  -- 0x0
(II) RADEON(0): Port2:
 Monitor   -- AUTO
 Connector -- STV
 DAC Type  -- TVDAC/ExtDAC
 TMDS Type -- None
 DDC Type  -- 0x0
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA-0:ddc2" removed.
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA-0:ddc2" removed.
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA-0:ddc2" removed.
(II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
finished output detect: 0
(II) RADEON(0): Output: LVDS, Detected Monitor Type: 0
finished output detect: 1
(II) RADEON(0): Output: S-video, Detected Monitor Type: 0
finished output detect: 2
finished all detect
before xf86InitialConfiguration
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA-0:ddc2" removed.
(II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "VGA-0:ddc2" removed.
 

Curryfrosch

Member
Narf....gute Frage. Ich hab grad Bootmenü und KDM-Login durcheinandergewürfelt. Konsolensitzung kannst Du nicht auswählen weil Du bis zum KDM-Login gar nicht kommst. :irre:

Nachtrag: Dürfte aber funktionieren, wenn im Bootmenü als Bootparameter init=3 hinzugefügt wird.
 
Oben