Hallo,
nachdem ich unter meinem SuSE 10.3 mehrere Warnungen von SMART bekam habe ich als su folgenden Test ausführen lassen:
Das ganze hat 67 Minuten gedauert.
Nach Eingabe von "smartctl -a /dev/sda" bekam ich folgende Meldung:
Allerdings kann ich glaube ich die Tragweite dieser Informationen nicht eindeutig interpretieren:
Es gibt offensichtlich mehrere Fehlermeldungen...
Heißt das jetzt, dass ich eine neue Festplatte brauche?
Danke schon mal für Eure Hilfe
Gruß
Wolfgang
nachdem ich unter meinem SuSE 10.3 mehrere Warnungen von SMART bekam habe ich als su folgenden Test ausführen lassen:
Code:
smartctl -t long /dev/sda
Nach Eingabe von "smartctl -a /dev/sda" bekam ich folgende Meldung:
Code:
smartctl version 5.37 [i686-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6G160P0
Serial Number: G202YGGG
Firmware Version: KA201UW0
User Capacity: 160.041.885.696 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sat Sep 6 15:46:04 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (2281) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 67) minutes.
SMART Attributes Data Structure revision number: 32
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 100 100 025 Pre-fail Always - 15958
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 587
5 Reallocated_Sector_Ct 0x0033 100 100 025 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 098 097 074 Pre-fail Always - 53166
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1028
10 Spin_Retry_Count 0x002b 100 100 004 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 100 100 070 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 605
184 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
187 Unknown_Attribute 0x0032 076 076 000 Old_age Always - 24
188 Unknown_Attribute 0x0032 097 097 000 Old_age Always - 3
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 064 055 040 Old_age Always - 605356068
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 587
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1617
194 Temperature_Celsius 0x0032 034 253 000 Old_age Always - 36
195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 12113
196 Reallocated_Event_Count 0x0008 100 100 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 087 087 000 Old_age Offline - 416
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 100 100 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 100 100 027 Pre-fail Always - 11
207 Spin_High_Current 0x002a 100 100 000 Old_age Always - 0
208 Spin_Buzz 0x002a 100 100 000 Old_age Always - 0
210 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
211 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
212 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 24 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 24 occurred at disk power-on lifetime: 961 hours (40 days + 1 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:19:21.974 IDENTIFY DEVICE
c8 00 08 52 85 a8 e2 00 00:19:18.809 READ DMA
27 00 00 00 00 00 e0 00 00:19:18.793 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:19:18.785 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:19:18.781 SET FEATURES [Set transfer mode]
Error 23 occurred at disk power-on lifetime: 961 hours (40 days + 1 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:19:18.669 IDENTIFY DEVICE
c8 00 08 52 85 a8 e2 00 00:19:15.504 READ DMA
27 00 00 00 00 00 e0 00 00:19:15.489 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:19:15.481 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:19:15.476 SET FEATURES [Set transfer mode]
Error 22 occurred at disk power-on lifetime: 961 hours (40 days + 1 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:19:15.364 IDENTIFY DEVICE
c8 00 08 52 85 a8 e2 00 00:19:12.200 READ DMA
27 00 00 00 00 00 e0 00 00:19:12.184 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:19:12.176 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:19:12.171 SET FEATURES [Set transfer mode]
Error 21 occurred at disk power-on lifetime: 961 hours (40 days + 1 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 50 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:19:12.059 IDENTIFY DEVICE
c8 00 08 52 85 a8 e2 00 00:19:08.895 READ DMA
27 00 00 00 00 00 e0 00 00:19:08.879 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:19:08.871 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:19:08.866 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 1026 9446
# 2 Short offline Completed without error 00% 464 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Allerdings kann ich glaube ich die Tragweite dieser Informationen nicht eindeutig interpretieren:
Es gibt offensichtlich mehrere Fehlermeldungen...
Heißt das jetzt, dass ich eine neue Festplatte brauche?
Danke schon mal für Eure Hilfe
Gruß
Wolfgang