• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

eterne Festplatte läuft nicht

G

grisse

Member
hi
habe suse 10.3 und hab vor kurzem eine eterne Festplatte (Maxtor 233 Gigs ) ngeschlossen. So weit so gut. Zuerst war sie mit NTFS formtiert und somit konnte ich sie zumindest lesen aber leider nicht schreiben. Dann hab ich sie komplett neu fomatieren wollen mit reiserfs und wenn ich das mit yast mache dann brincht er am ende mit einer Fehlermeldung ab dass es Probleme gegeben hat.
Kann mir jemand sagen woran das lieben kann oder mit einen Tipp geben oder mir ein anderes Programm empfehlen mit dem das klappen könnte.
thx
chris
 
W

whois

Ultimate Guru
Hi Chris

Steht da ein bisschen mehr als nur"Probleme gegeben".
So ist das ein bisschen schwierig.

cu
 
OP
G

grisse

Member
habs grad wieder probiert mit dem Formatiern und jetzt hats geklappt und konte sogar datei drauf speichern.
dann wollte ich ihn neu booten und beim booten mach er er "replying tree check und da kommt dann bei der Mator festplatte dieFehlerinfo "no sense information und bleibt dann hängen bzw man knn sich dann nur als oot über die konsole einloggen.
Dann hab ich die externe Partion wieder gelöscht und das botten funktioniert wieder wie gewohnt.
Das komische ist dass es aber die korrekte Platte im Yast erkennt aber sobald ich eine Partion mache oder formatioere gibts probelme beim booten oder es funktioniert von vornherein nicht
bin jetzt einbißchen ratlos
lg
chris
 
W

whois

Ultimate Guru
Hi

Mit welchem Filesystem formatiert?

Steck die Platte und gib mal die Befehle
Code: 
mount und dmesg
ein und poste das Ergebnis.

cu
 
OP
G

grisse

Member
ok
der Befehl mount bringt folgndes
Code: 
/dev/sda4 on / type reiserfs (rw,acl,user_xattr)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda1 on /Platte20 type reiserfs (rw)
/dev/sda5 on /Platte60 type reiserfs (rw)
fusectl on /sys/fs/fuse/connections type fusectl (rw)
securityfs on /sys/kernel/security type securityfs (rw)
none on /proc/fs/vmblock/mountPoint type vmblock (rw)

und der Befehl dmesg folgendes
Code: 
/dev/sda4 on / type reiserfs (rw,acl,user_xattr)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda1 on /Platte20 type reiserfs (rw)
/dev/sda5 on /Platte60 type reiserfs (rw)
fusectl on /sys/fs/fuse/connections type fusectl (rw)
securityfs on /sys/kernel/security type securityfs (rw)
none on /proc/fs/vmblock/mountPoint type vmblock (rw)



kannst du damit was anfangen und mirsagen woran es liegt ?
thx
chris
 
OP
G

grisse

Member
nochmal der Befehl dmesg

Code: 
Linux version 2.6.22.5-31-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2007/09/21 22:29:00 UTC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
 BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data)
 BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS)
 BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 261856) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   261856
early_node_map[1] active PFN ranges
    0:        0 ->   261856
On node 0 totalpages: 261856
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 253 pages used for memmap
  HighMem zone: 32227 pages, LIFO batch:7
DMI present.
Using APIC driver default
ACPI: RSDP 000F6BD0, 0014 (r0 TOSCPL)
ACPI: RSDT 3FEE39F5, 0048 (r1 TOSCPL   RSDT    6040000  LTP        0)
ACPI: APIC 3FEE9E88, 0068 (r1 INTEL  ALVISO    6040000 LOHR       5F)
ACPI: FACP 3FEE9EF0, 0074 (r1 TOSCPL ALVISO    6040000 LOHR       32)
ACPI: DSDT 3FEE4F5E, 4F2A (r1 TOSCPL ALVISO    6040000 MSFT  100000E)
ACPI: FACS 3FEFAFC0, 0040
ACPI: BOOT 3FEE9FD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: MCFG 3FEE9F9C, 003C (r1 INTEL  ALVISO    6040000 LOHR       5F)
ACPI: SSDT 3FEE490B, 064F (r1 SataRe  SataPri     1000 INTL 20030224)
ACPI: SSDT 3FEE4279, 0692 (r1 SataRe  SataSec     1000 INTL 20030224)
ACPI: SSDT 3FEE3E34, 0277 (r1  PmRef  Cpu0Ist     3000 INTL 20030224)
ACPI: SSDT 3FEE3C56, 01DE (r1  PmRef  Cpu0Cst     3001 INTL 20030224)
ACPI: SSDT 3FEE3A3D, 0219 (r1  PmRef    CpuPm     3000 INTL 20030224)
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists.  Total pages: 259811
Kernel command line: root=/dev/disk/by-id/scsi-SATA_TOSHIBA_MK1032G_95RM3193S-part4 vga=0x314    resume=/dev/sda2 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1862.112 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030364k/1047424k available (1825k kernel code, 16408k reserved, 764k data, 228k init, 129920k highmem)
virtual kernel memory layout:
    fixmap  : 0xffdf4000 - 0xfffff000   (2092 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc038e000 - 0xc03c7000   ( 228 kB)
      .data : 0xc02c86ed - 0xc0387964   ( 764 kB)
      .text : 0xc0100000 - 0xc02c86ed   (1825 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3727.90 BogoMIPS (lpj=7455819)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00002040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
Unpacking initramfs... done
Freeing initrd memory: 4012k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 812 Objects with 56 Devices 203 Methods 26 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 10 Objects with 3 Devices 4 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 10 Objects with 3 Devices 4 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0004) - 5 Objects with 0 Devices 3 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0005) - 1 Objects with 0 Devices 1 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0006) - 10 Objects with 0 Devices 2 Methods 0 Regions
 tbxface-0587 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
CPU0: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
Total of 1 processors activated (3727.90 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 2 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:...............................................................
Initialized 25/26 Regions 0/0 Fields 25/25 Buffers 13/22 Packages (857 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 0 _STA executions (examined 66 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Force enabled HPET at base address 0xfed00000
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
ACPI: RTC can wake from S4
pnp: 00:01: ioport range 0xfe00-0xfe7f has been reserved
pnp: 00:01: ioport range 0xfe80-0xfeff has been reserved
pnp: 00:01: ioport range 0xff00-0xff7f has been reserved
pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:01: iomem range 0xf0000000-0xf0003fff could not be reserved
pnp: 00:01: iomem range 0xf0004000-0xf0004fff could not be reserved
pnp: 00:01: iomem range 0xf0005000-0xf0005fff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
  IO window: 3000-3fff
  MEM window: b8100000-b81fffff
  PREFETCH window: c8000000-cfffffff
PCI: Bridge: 0000:00:1c.0
  IO window: 4000-4fff
  MEM window: bc000000-bfffffff
  PREFETCH window: d0000000-d3ffffff
PCI: Bridge: 0000:00:1c.1
  IO window: 5000-5fff
  MEM window: c0000000-c3ffffff
  PREFETCH window: d4000000-d7ffffff
PCI: Bus 7, cardbus bridge: 0000:06:04.0
  IO window: 00006400-000064ff
  IO window: 00006800-000068ff
  PREFETCH window: 50000000-53ffffff
  MEM window: 54000000-57ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 6000-6fff
  MEM window: c4000000-c40fffff
  PREFETCH window: 50000000-53ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
audit: initializing netlink socket (disabled)
audit(1217344555.388:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
vesafb: framebuffer at 0xc8000000, mapped to 0xf8880000, using 3750k, total 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:af9a
vesafb: pmi: set display start = c00cb028, set palette = c00cb068
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 78734 bytes
bootsplash: ...found (800x600, 27773 bytes, v3).
Console: switching to colour frame buffer device 96x33
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 18
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
Switched to NOHz mode on CPU #0
floppy0: no floppy controllers found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
NET: Registered protocol family 1
Using IPI No-Shortcut mode
Freeing unused kernel memory: 228k freed
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI Exception (processor_core-0787): AE_NOT_FOUND, Processor Device is not present [20070126]
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ahci: probe of 0000:00:1f.2 failed with error -22
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000118f0 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000118f8 irq 15
Marking TSC unstable due to: possible TSC halt in C2.
Time: hpet clocksource has been installed.
ata1.00: failed to set max address (err_mask=0x1)
ata1.00: device aborted resize (194980905 -> 195371568), skipping HPA handling
ata1.00: ATA-6: TOSHIBA MK1032GAX, AB211A, max UDMA/100
ata1.00: 194980905 sectors, multi 16: LBA48 
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
input: AT Translated Set 2 keyboard as /class/input/input3
Clocksource tsc unstable (delta = -275251285 ns)
ata2.00: ATAPI: DV-W28EAT, 1.9B, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK1032GA AB21 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            TEAC     DV-W28EAT        1.9B PQ: 0 ANSI: 5
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001800
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] 194980905 512-byte hardware sectors (99830 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 194980905 512-byte hardware sectors (99830 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<6>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
 sda1 sda2 sda3 < sda5 > sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001840
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xb8000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.22.5-31-default ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: new device found, idVendor=0d49, idProduct=5000
usb 4-1: new device strings: Mfr=1, Product=3, SerialNumber=2
usb 4-1: Product: 5000XT v01.00.00
usb 4-1: Manufacturer: Maxtor
usb 4-1: SerialNumber: A80DWWBE    
usb 4-1: configuration #1 chosen from 1 choice
usb 2-1: new low speed USB device using uhci_hcd and address 3
usb 2-1: new device found, idVendor=1267, idProduct=0201
usb 2-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-1: Product: USB Mouse
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: USB Mouse as /class/input/input4
input: USB HID v1.00 Mouse [USB Mouse] on usb-0000:00:1d.1-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
REISERFS (device sda4): found reiserfs format "3.6" with standard journal
REISERFS (device sda4): using ordered data mode
reiserfs: using flush barriers
REISERFS (device sda4): journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda4): checking transaction log (sda4)
REISERFS (device sda4): Using r5 hash to sort names
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
Linux agpgart interface v0.102 (c) Dave Jones
intel_rng: FWH not detected
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 928 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.42.3 [Oct 19 2007] on minor 0
iTCO_vendor_support: vendor-support=0
Initializing USB Mass Storage driver...
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:06 failed with error -16
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input6
ACPI: Lid Switch [LID0]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PWRB]
ieee80211_crypt: registered algorithm 'NULL'
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1e.3 to 64
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 20 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[c4004000-c40047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1e.2 to 64
ACPI: AC Adapter [ACAD] (on-line)
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ACPI: Battery Slot [BAT1] (battery present)
scsi 2:0:0:0: Direct-Access     Maxtor   5000XT v01.00.00 0100 PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdb] 490232832 512-byte hardware sectors (250999 MB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 490232832 512-byte hardware sectors (250999 MB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
 sdb:<6>intel8x0_measure_ac97_clock: measured 52820 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 22
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
8139cp 0000:06:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:06:01.0: Try the "8139too" driver instead.
sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1)
ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 17 (level, low) -> IRQ 17
mmc0: SDHCI at 0xc4007000 irq 17 DMA
Yenta: CardBus bridge found at 0000:06:04.0 [1179:ff01]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:04.0, mfunc 0x89501212, devctl 0x44
8139too Fast Ethernet driver 0.9.28
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f5a764023a0]
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
cs: IO port probe 0x6000-0x6fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xc40fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 23
eth1: RealTek RTL8139 at 0xf9024800, 00:0f:b0:a0:7c:44, IRQ 23
eth1:  Identified 8139 chip type 'RTL-8100B/8139D'
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information

sd 2:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
Adding 1558296k swap on /dev/sda2.  Priority:-1 extents:1 across:1558296k
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
loop: module loaded
REISERFS (device sda1): found reiserfs format "3.6" with standard journal
REISERFS (device sda1): using ordered data mode
reiserfs: using flush barriers
REISERFS (device sda1): journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda1): checking transaction log (sda1)
REISERFS (device sda1): Using r5 hash to sort names
REISERFS (device sda5): found reiserfs format "3.6" with standard journal
REISERFS (device sda5): using ordered data mode
reiserfs: using flush barriers
REISERFS (device sda5): journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device sda5): checking transaction log (sda5)
REISERFS (device sda5): Using r5 hash to sort names
fuse init (API version 7.8)
AppArmor: AppArmor initialized
audit(1217344595.133:2):  type=1505 info="AppArmor initialized" pid=2023
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
powernow: This module only works with AMD K7 CPUs
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8183 buckets, 65464 max)
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
sd 2:0:0:0: [sdb] Sense Key : No Sense [current] 
sd 2:0:0:0: [sdb] Add. Sense: No additional sense information
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
audit(1217344651.214:3): audit_backlog_limit=320 old=64 by auid=4294967295 res=1
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1217344651.214:4): audit_pid=2945 old=0 by auid=4294967295
eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[fglrx] Reserve Block - 0 offset =  0X7ffb000 length = 0X5000
[fglrx] Reserve Block - 1 offset =  0X0 length = 0X40000
[fglrx] Reserve Block - 2 offset =  0X7fbb000 length = 0X40000
NET: Registered protocol family 17
/dev/vmmon[3286]: VMCI: Driver initialized.
/dev/vmmon[3286]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[3286]: Initial HV check: anyNotCapable=1 anyUnlocked=0 anyEnabled=0 anyDisabled=0
/dev/vmmon[3286]: Module vmmon: initialized
/dev/vmnet: open called by PID 3338 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 3356 (vmnet-netifup)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 3354 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 3391 (vmnet-natd)
/dev/vmnet: port on hub 8 successfully opened
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=231 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=211 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=169 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=149 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=214 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=194 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=169 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=149 
vmnet8: no IPv6 routers present
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=144 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=124 
eth1: no IPv6 routers present
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
PPP generic driver version 2.4.2
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
NET: Registered protocol family 24
ppp0 renamed to dsl0
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=88.65.67.226 DST=88.65.174.232 LEN=52 TOS=0x00 PREC=0x00 TTL=59 ID=58662 DF PROTO=TCP SPT=28578 DPT=135 WINDOW=60352 RES=0x00 SYN URGP=0 OPT (020405A00103030201010402) 
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=60.222.224.157 DST=88.65.174.232 LEN=485 TOS=0x00 PREC=0x00 TTL=47 ID=0 DF PROTO=UDP SPT=49569 DPT=1027 LEN=465 
SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=172.16.112.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT-INV IN=dsl0 OUT= MAC= SRC=217.12.10.64 DST=88.65.174.232 LEN=40 TOS=0x00 PREC=0x00 TTL=54 ID=3602 DF PROTO=TCP SPT=995 DPT=27789 WINDOW=65535 RES=0x00 ACK RST URGP=0 
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=169.254.48.197 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=88.65.212.162 DST=88.65.174.232 LEN=64 TOS=0x00 PREC=0x00 TTL=43 ID=44616 DF PROTO=TCP SPT=20234 DPT=135 WINDOW=53760 RES=0x00 SYN URGP=0 OPT (02040586010303030101080A000000000000000001010402) 
SFW2-INext-DROP-DEFLT IN=dsl0 OUT= MAC= SRC=88.65.212.162 DST=88.65.174.232 LEN=64 TOS=0x00 PREC=0x00 TTL=43 ID=45368 DF PROTO=TCP SPT=20234 DPT=135 WINDOW=53760 RES=0x00 SYN URGP=0 OPT (02040586010303030101080A000000000000000001010402)
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben