DVD mit SATA Converter (delock) nicht erkannt

Inspecting /boot/System.map-2.6.22.17-0.1-default
Loaded 26163 symbols from /boot/System.map-2.6.22.17-0.1-default.
Symbols match kernel version 2.6.22.
No module symbols loaded - kernel modules not enabled.

klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.22.17-0.1-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2008/02/10 20:01:04 UTC
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
<4> BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000007d5b0000 (usable)
<4> BIOS-e820: 000000007d5b0000 - 000000007d5c9000 (ACPI data)
<4> BIOS-e820: 000000007d5c9000 - 000000007d5cc000 (ACPI NVS)
<4> BIOS-e820: 000000007d5cc000 - 000000007d800000 (reserved)
<4> BIOS-e820: 000000007e000000 - 0000000080000000 (reserved)
<4> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
<4> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<4> BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
<5>1109MB HIGHMEM available.
<5>896MB LOWMEM available.
<6>found SMP MP-table at 000f6030
<7>Entering add_active_range(0, 0, 513456) 0 entries of 256 used
<4>Zone PFN ranges:
<4> DMA 0 -> 4096
<4> Normal 4096 -> 229376
<4> HighMem 229376 -> 513456
<4>early_node_map[1] active PFN ranges
<4> 0: 0 -> 513456
<7>On node 0 totalpages: 513456
<7> DMA zone: 32 pages used for memmap
<7> DMA zone: 0 pages reserved
<7> DMA zone: 4064 pages, LIFO batch:0
<7> Normal zone: 1760 pages used for memmap
<7> Normal zone: 223520 pages, LIFO batch:31
<7> HighMem zone: 2219 pages used for memmap
<7> HighMem zone: 281861 pages, LIFO batch:31
<6>DMI present.
<6>Using APIC driver default
<4>ACPI: RSDP 000F5E20, 0024 (r2 PTLTD )
<4>ACPI: XSDT 7D5BD920, 00B4 (r1 LENOVO TC-2R 60400D0 LTP 0)
<4>ACPI: TCPA 7D5C8BB9, 0032 (r2 LENOVO TC-2R 60400D0 PTL 0)
<4>ACPI: FACP 7D5C8BEB, 00F4 (r3 INTEL 60400D0 PTL 3)
<4>ACPI: DSDT 7D5C1019, 7B2C (r1 INTEL BEARLAKE 60400D0 MSFT 100000E)
<4>ACPI: FACS 7D5CBFC0, 0040
<4>ACPI: _MAR 7D5C8CDF, 0030 (r1 Intel OEMDMAR 60400D0 LOHR 1)
<4>ACPI: SLIC 7D5C8D0F, 0176 (r1 LENOVO TC-2R 60400D0 LTP 0)
<4>ACPI: MCFG 7D5C8E85, 003C (r1 PTLTD MCFG 60400D0 LTP 0)
<4>ACPI: HPET 7D5C8EC1, 0038 (r1 PTLTD HPETTBL 60400D0 LTP 1)
<4>ACPI: APIC 7D5C8EF9, 0068 (r1 PTLTD APIC 60400D0 LTP 0)
<4>ACPI: BOOT 7D5C8F61, 0028 (r1 PTLTD $SBFTBL$ 60400D0 LTP 1)
<4>ACPI: ASF! 7D5C8F89, 0077 (r16 CETP CETP 60400D0 PTL 1)
<4>ACPI: SSDT 7D5BF263, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BF1BD, 00A6 (r1 PmRef Cpu7Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BF117, 00A6 (r1 PmRef Cpu6Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BF071, 00A6 (r1 PmRef Cpu5Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BEFCB, 00A6 (r1 PmRef Cpu4Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BEF25, 00A6 (r1 PmRef Cpu3Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BEE7F, 00A6 (r1 PmRef Cpu2Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BEDD9, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050228)
<4>ACPI: SSDT 7D5BD9D4, 1405 (r1 PmRef CpuPm 3000 INTL 20050228)
<6>ACPI: PM-Timer IO Port: 0x1008
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>Processor #0 7:7 APIC version 20
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
<4>Processor #1 7:7 APIC version 20
<6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
<7>ACPI: IRQ0 used by override.
<7>ACPI: IRQ2 used by override.
<7>ACPI: IRQ9 used by override.
<4>Enabling APIC mode: Flat. Using 1 I/O APICs
<6>ACPI: HPET id: 0xffffffff base: 0xfed00000
<6>Using ACPI (MADT) for SMP configuration information
<4>Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
<4>Built 1 zonelists. Total pages: 509445
<5>Kernel command line: root=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 vga=0x31a resume=/dev/sda10 splash=native
<7>mapped APIC to ffffd000 (fee00000)
<7>mapped IOAPIC to ffffc000 (fec00000)
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 16384 bytes)
<4>Detected 2992.611 MHz processor.
<4>Console: colour dummy device 80x25
<4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 2028100k/2053824k available (1829k kernel code, 24404k reserved, 764k data, 228k init, 1136320k highmem)
<4>virtual kernel memory layout:
<4> fixmap : 0xffdf4000 - 0xfffff000 (2092 kB)
<4> pkmap : 0xff800000 - 0xffc00000 (4096 kB)
<4> vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
<4> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
<4> .init : 0xc0390000 - 0xc03c9000 ( 228 kB)
<4> .data : 0xc02c95cb - 0xc0388964 ( 764 kB)
<4> .text : 0xc0100000 - 0xc02c95cb (1829 kB)
<4>Checking if this processor honours the WP bit even in supervisor mode... Ok.
<6>hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
<6>hpet0: 4 64-bit timers, 14318180 Hz
<4>Calibrating delay using timer specific routine.. 5988.87 BogoMIPS (lpj=11977753)
<6>Security Framework v1.0.0 initialized
<4>Mount-cache hash table entries: 512
<7>CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0008e3fd 00000000 00000001
<4>monitor/mwait feature present.
<4>using mwait in idle threads.
<6>CPU: L1 I cache: 32K, L1 D cache: 32K
<6>CPU: L2 cache: 6144K
<6>CPU: Physical Processor ID: 0
<6>CPU: Processor Core ID: 0
<7>CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0008e3fd 00000000 00000001
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<4>Compat vDSO mapped to ffffe000.
<6>Checking 'hlt' instruction... OK.
<6>SMP alternatives: switching to UP code
<6>Unpacking initramfs... done
<6>Freeing initrd memory: 4070k freed
<6>ACPI: Core revision 20070126
<4>Parsing all Control Methods:
<4>Table [DSDT](id 0001) - 810 Objects with 83 Devices 183 Methods 51 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0002) - 7 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0003) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0004) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0005) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0006) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0007) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0008) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 0009) - 4 Objects with 0 Devices 3 Methods 0 Regions
<4>Parsing all Control Methods:
<4>Table [SSDT](id 000A) - 43 Objects with 0 Devices 16 Methods 0 Regions
<4> tbxface-0587 [00] tb_load_namespace : ACPI Tables successfully acquired
<4>evxfevnt-0091 [00] enable : Transition to ACPI mode successful
<4>CPU0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
<6>SMP alternatives: switching to SMP code
<4>Booting processor 1/1 eip 3000
<6>Initializing CPU#1
<4>Calibrating delay using timer specific routine.. 5984.96 BogoMIPS (lpj=11969931)
<7>CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0008e3fd 00000000 00000001
<4>monitor/mwait feature present.
<6>CPU: L1 I cache: 32K, L1 D cache: 32K
<6>CPU: L2 cache: 6144K
<6>CPU: Physical Processor ID: 0
<6>CPU: Processor Core ID: 1
<7>CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0008e3fd 00000000 00000001
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#1.
<4>CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
<6>Total of 2 processors activated (11973.84 BogoMIPS).
<4>ENABLING IO-APIC IRQs
<6>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<4>APIC calibration not consistent with PM Timer: 187ms instead of 100ms
<6>APIC delta adjusted to PM-Timer: 2078121 (3906825)
<6>checking TSC synchronization [CPU#0 -> CPU#1]: passed.
<6>Brought up 2 CPUs
<4>migration_cost=8
<6>Booting paravirtualized kernel on bare hardware
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<6>PCI: Using MMCONFIG
<4>Setting up standard PCI resources
<4>evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 3F [_GPE] 8 regs on int 0x9
<4>evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 11 Wake, Enabled 3 Runtime GPEs in this block
<7>ACPI: EC: Look up EC in DSDT
<4>Completing Region/Field/Buffer/Package initialization:.............................................................................................
<4>Initialized 45/51 Regions 0/0 Fields 39/39 Buffers 9/31 Packages (897 nodes)
<4>Initializing Device/Processor/Thermal objects by executing _INI methods:.
<4>Executed 1 _INI methods requiring 0 _STA executions (examined 93 objects)
<6>ACPI: Interpreter enabled
<6>ACPI: (supports S0 S3 S4 S5)
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<7>PCI: Probing PCI hardware (bus 00)
<4>PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
<4>PCI quirk: region 1180-11bf claimed by ICH6 GPIO
<6>PCI: Transparent bridge - 0000:00:1e.0
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>ACPI: bus type pnp registered
<6>pnp: PnP ACPI: found 14 devices
<6>ACPI: ACPI bus type pnp unregistered
<6>PnPBIOS: Disabled by ACPI PNP
<6>PCI: Using ACPI for IRQ routing
<6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<4>ACPI: RTC can wake from S4
<6>pnp: 00:01: iomem range 0xfed11000-0xfed11fff has been reserved
<6>pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
<6>pnp: 00:01: iomem range 0xfed18000-0xfed1ffff has been reserved
<6>pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
<6>Time: tsc clocksource has been installed.
<3>PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
<6>PCI: Bridge: 0000:00:01.0
<6> IO window: 2000-2fff
<6> MEM window: d0000000-d1ffffff
<6> PREFETCH window: c0000000-cfffffff
<6>PCI: Bridge: 0000:00:1e.0
<6> IO window: disabled.
<6> MEM window: d2000000-d20fffff
<6> PREFETCH window: disabled.
<6>ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:00:01.0 to 64
<7>PCI: Setting latency timer of device 0000:00:1e.0 to 64
<6>NET: Registered protocol family 2
<6>Switched to NOHz mode on CPU #1
<6>Switched to NOHz mode on CPU #0
<4>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
<4>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>Simple Boot Flag at 0x44 set to 0x1
<6>Machine check exception polling timer started.
<6>audit: initializing netlink socket (disabled)
<5>audit(1213175149.464:1): initialized
<4>highmem bounce pool size: 64 pages
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<7>Boot video device is 0000:01:00.0
<7>PCI: Setting latency timer of device 0000:00:01.0 to 64
<4>assign_interrupt_mode Found MSI capability
<7>Allocate Port Service[0000:00:01.0cie00]
<7>Allocate Port Service[0000:00:01.0cie03]
<6>vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 10240k, total 262144k
<6>vesafb: mode is 1280x1024x16, linelength=2560, pages=1
<6>vesafb: protected mode interface info at c000:c2e0
<6>vesafb: pmi: set display start = c00cc316, set palette = c00cc380
<6>vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
<6>vesafb: scrolling: redraw
<6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<6>bootsplash 3.1.6-2004/03/31: looking for picture...
<6>bootsplash: silentjpeg size 98233 bytes
<6>bootsplash: ...found (1280x1024, 35219 bytes, v3).
<4>Console: switching to colour frame buffer device 160x64
<6>fb0: VESA VGA frame buffer device
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Real Time Clock Driver v1.12ac
<7>hpet_resources: 0xfed00000 is busy
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>ACPI: PCI Interrupt 0000:00:03.3 -> GSI 17 (level, low) -> IRQ 17
<6>0000:00:03.3: ttyS1 at I/O 0x1c88 (irq = 17) is a 16550A
<6>FDC 0 is a post-1991 82077
<6>PNP: PS/2 Controller [PNP0f13:MSE0] at 0x60,0x64 irq 12
<4>PNP: PS/2 controller doesn't have KBD irq; using default 1
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>serio: i8042 AUX port at 0x60,0x64 irq 12
<6>mice: PS/2 mouse device common for all mice
<6>input: PC Speaker as /class/input/input0
<6>input: PS2++ Logitech Mouse as /class/input/input1
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<6>Freeing unused kernel memory: 228k freed
<4>ACPI: SSDT 7D5BF4C2, 01DD (r1 PmRef Cpu0Ist 3000 INTL 20050228)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 00F5) - 6 Objects with 0 Devices 3 Methods 0 Regions
<4>ACPI: SSDT 7D5BF69F, 016E (r1 PmRef Cpu1Ist 3000 INTL 20050228)
<4>Parsing all Control Methods:
<4>Table [SSDT](id 00F8) - 6 Objects with 0 Devices 3 Methods 0 Regions
<4>ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not present [20070126]
<4>ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not present [20070126]
<4>ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not present [20070126]
<4>ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not present [20070126]
<4>ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not present [20070126]
<4>ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not present [20070126]
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<7>ata_piix 0000:00:1f.2: version 2.11
<6>ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
<6>ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 17 (level, low) -> IRQ 17
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>scsi0 : ata_piix
<6>scsi1 : ata_piix
<6>ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011c40 irq 14
<6>ata2: SATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011c48 irq 15
<6>ata1.00: ATA-7: Hitachi HDT725032VLA380, V54OA7DA, max UDMA/100
<6>ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
<6>ata1.00: configured for UDMA/100
<6>ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H55L, 1.02, max UDMA/66
<6>ata2.00: applying bridge limits
<6>ata2.00: configured for UDMA/66
<6>ata2: EH pending after completion, repeating EH (cnt=4)
<5>scsi 0:0:0:0: Direct-Access ATA Hitachi HDT72503 V54O PQ: 0 ANSI: 5
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
<4> res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)

<4>ata2: port is slow to respond, please be patient (Status 0xd0)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/66
<6>ata2: EH pending after completion, repeating EH (cnt=4)
<6>ata2: EH complete
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
<4> res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/66
<6>ata2: EH pending after completion, repeating EH (cnt=4)
<6>ata2: EH complete
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
<4> res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/66
<6>ata2: EH pending after completion, repeating EH (cnt=4)
<6>ata2: EH complete
<4>ata2.00: limiting speed to UDMA/44IO4
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x12 data 96 in
<4> res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
<4>ata2: port is slow to respond, please be patient (Status 0xd8)
<4>ata2: device not ready (errno=-16), forcing hardreset
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/44
<6>ata2: EH pending after completion, repeating EH (cnt=4)
<6>ata2: EH complete
[/b]
<6>scsi scan: 96 byte inquiry failed. Consider BLIST_INQUIRY_36 for this device
<5>scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H55L 1.02 PQ: 0 ANSI: 5[/b]
<6>ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
<6>ACPI: PCI Interrupt 0000:00:1f.5[C] -> GSI 18 (level, low) -> IRQ 18
<7>PCI: Setting latency timer of device 0000:00:1f.5 to 64
<6>scsi2 : ata_piix
<6>scsi3 : ata_piix
<6>ata3: SATA max UDMA/133 cmd 0x00011cb8 ctl 0x00011cae bmdma 0x00011c60 irq 18
<6>ata4: SATA max UDMA/133 cmd 0x00011cb0 ctl 0x00011caa bmdma 0x00011c68 irq 18
<6>ata4.00: ATA-8: Hitachi HDP725050GLA360, GM4OA52A, max UDMA/133
<6>ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
<6>ata4.00: configured for UDMA/133
<5>scsi 3:0:0:0: Direct-Access ATA Hitachi HDP72505 GM4O PQ: 0 ANSI: 5
<6>BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<5>sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
<5>sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1 sda3 <<7>PCI: Setting latency timer of device 0000:00:1a.7 to 64
<6>ehci_hcd 0000:00:1a.7: EHCI Host Controller
<6>ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
<6>ehci_hcd 0000:00:1a.7: debug port 1
<7>PCI: cache line size of 32 is not supported by device 0000:00:1a.7
<6>ehci_hcd 0000:00:1a.7: irq 18, io mem 0xd2326800
<6>USB Universal Host Controller Interface driver v3.0
<4> sda5 sda6<6>ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb1: new device found, idVendor=0000, idProduct=0000
<6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: EHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.22.17-0.1-default ehci_hcd
<6>usb usb1: SerialNumber: 0000:00:1a.7
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 6 ports detected
<4> sda7 sda8 sda9 sda10 >
<5>sd 0:0:0:0: [sda] Attached SCSI disk
<5>sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
<5>sd 3:0:0:0: [sdb] Write Protect is off
<7>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
<5>sd 3:0:0:0: [sdb] Write Protect is off
<7>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sdb:<6>ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:00:1d.7 to 64
<6>ehci_hcd 0000:00:1d.7: EHCI Host Controller
<6>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
<4> sdb1 sdb2 sdb3 sdb4
<5>sd 3:0:0:0: [sdb] Attached SCSI disk
<6>ehci_hcd 0000:00:1d.7: debug port 1
<7>PCI: cache line size of 32 is not supported by device 0000:00:1d.7
<6>ehci_hcd 0000:00:1d.7: irq 16, io mem 0xd2326c00
<6>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb2: new device found, idVendor=0000, idProduct=0000
<6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: EHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.22.17-0.1-default ehci_hcd
<6>usb usb2: SerialNumber: 0000:00:1d.7
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 6 ports detected
<6>ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:00:1a.0 to 64
<6>uhci_hcd 0000:00:1a.0: UHCI Host Controller
<6>uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
<6>uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001840
<6>usb usb3: new device found, idVendor=0000, idProduct=0000
<6>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: UHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.22.17-0.1-default uhci_hcd
<6>usb usb3: SerialNumber: 0000:00:1a.0
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1a.1 -> GSI 17 (level, low) -> IRQ 17
<7>PCI: Setting latency timer of device 0000:00:1a.1 to 64
<6>uhci_hcd 0000:00:1a.1: UHCI Host Controller
<6>uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
<6>uhci_hcd 0000:00:1a.1: irq 17, io base 0x00001860
<6>usb usb4: new device found, idVendor=0000, idProduct=0000
<6>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb4: Product: UHCI Host Controller
<6>usb usb4: Manufacturer: Linux 2.6.22.17-0.1-default uhci_hcd
<6>usb usb4: SerialNumber: 0000:00:1a.1
<6>usb usb4: configuration #1 chosen from 1 choice
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
<7>PCI: Setting latency timer of device 0000:00:1a.2 to 64
<6>uhci_hcd 0000:00:1a.2: UHCI Host Controller
<6>uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
<6>uhci_hcd 0000:00:1a.2: irq 18, io base 0x00001880
<6>usb usb5: new device found, idVendor=0000, idProduct=0000
<6>usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb5: Product: UHCI Host Controller
<6>usb usb5: Manufacturer: Linux 2.6.22.17-0.1-default uhci_hcd
<6>usb usb5: SerialNumber: 0000:00:1a.2
<6>usb usb5: configuration #1 chosen from 1 choice
<6>hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:00:1d.0 to 64
<6>uhci_hcd 0000:00:1d.0: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
<6>uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
<6>usb usb6: new device found, idVendor=0000, idProduct=0000
<6>usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb6: Product: UHCI Host Controller
<6>usb usb6: Manufacturer: Linux 2.6.22.17-0.1-default uhci_hcd
<6>usb usb6: SerialNumber: 0000:00:1d.0
<6>usb usb6: configuration #1 chosen from 1 choice
<6>hub 6-0:1.0: USB hub found
<6>hub 6-0:1.0: 2 ports detected
<6>usb 2-6: new high speed USB device using ehci_hcd and address 4
<6>ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 17 (level, low) -> IRQ 17
<7>PCI: Setting latency timer of device 0000:00:1d.1 to 64
<6>uhci_hcd 0000:00:1d.1: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
<6>uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018c0
<6>usb usb7: new device found, idVendor=0000, idProduct=0000
<6>usb usb7: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb7: Product: UHCI Host Controller
<6>usb usb7: Manufacturer: Linux 2.6.22.17-0.1-default uhci_hcd
<6>usb usb7: SerialNumber: 0000:00:1d.1
<6>usb usb7: configuration #1 chosen from 1 choice
<6>hub 7-0:1.0: USB hub found
<6>hub 7-0:1.0: 2 ports detected
<6>usb 2-6: new device found, idVendor=04b8, idProduct=011e
<6>usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 2-6: Product: EPSON Scanner
<6>usb 2-6: Manufacturer: EPSON
<6>usb 2-6: configuration #1 chosen from 1 choice
<6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
<7>PCI: Setting latency timer of device 0000:00:1d.2 to 64
<6>uhci_hcd 0000:00:1d.2: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
<6>uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018e0
<6>usb usb8: new device found, idVendor=0000, idProduct=0000
<6>usb usb8: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb8: Product: UHCI Host Controller
<6>usb usb8: Manufacturer: Linux 2.6.22.17-0.1-default uhci_hcd
<6>usb usb8: SerialNumber: 0000:00:1d.2
<6>usb usb8: configuration #1 chosen from 1 choice
<6>hub 8-0:1.0: USB hub found
<6>hub 8-0:1.0: 2 ports detected
<6>usb 6-1: new low speed USB device using uhci_hcd and address 2
<4>swsusp: Basic memory bitmaps created
<4>swsusp: Basic memory bitmaps freed
<4>Attempting manual resume
<6>usb 6-1: new device found, idVendor=04b3, idProduct=3025
<6>usb 6-1: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 6-1: Product: USB NetVista Full Width Keyboard
<6>usb 6-1: Manufacturer: CHICONY
<6>usb 6-1: configuration #1 chosen from 1 choice
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda5, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>usb 6-2: new low speed USB device using uhci_hcd and address 3
<6>usb 6-2: new device found, idVendor=04b3, idProduct=310c
<6>usb 6-2: new device strings: Mfr=0, Product=2, SerialNumber=0
<6>usb 6-2: Product: USB Optical Mouse
<6>usb 6-2: configuration #1 chosen from 1 choice
<6>usbcore: registered new interface driver hiddev
<6>input: CHICONY USB NetVista Full Width Keyboard as /class/input/input2
<6>input: USB HID v1.10 Keyboard [CHICONY USB NetVista Full Width Keyboard] on usb-0000:00:1d.0-1
<6>input: USB Optical Mouse as /class/input/input3
<6>input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.0-2
<6>usbcore: registered new interface driver usbhid
<6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>scsi 1:0:0:0: Attached scsi generic sg1 type 5
<5>sd 3:0:0:0: Attached scsi generic sg2 type 0
<6>Linux agpgart interface v0.102 (c) Dave Jones
<6>rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
<4>rtc_cmos: probe of 00:05 failed with error -16
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:00:1b.0 to 64
<6>input: Power Button (FF) as /class/input/input4
<6>ACPI: Power Button (FF) [PWRF]
<6>input: Power Button (CM) as /class/input/input5
<6>ACPI: Power Button (CM) [PWRB]
<6>Intel(R) PRO/1000 Network Driver - 0.2.0
<6>Copyright (c) 1999-2007 Intel Corporation.
<6>ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:00:19.0 to 64
<6>parport_pc 00:0a: reported by Plug and Play ACPI
<6>parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
<6>parport0: Printer, Kyocera FS-1020D
<4>nvidia: module license 'NVIDIA' taints kernel.
<6>Linux video capture interface: v2.00
<6>0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1e:37:32:ad:26
<6>0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
<4>PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
<6>ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 17 (level, low) -> IRQ 17
<6>ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:01:00.0 to 64
<4>NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
<4>saa7146: register extension 'dvb'.
<6>ACPI: PCI Interrupt 0000:11:0a.0[A] -> GSI 22 (level, low) -> IRQ 19
<4>saa7146: found saa7146 @ mem f93c6000 (revision 1, irq 19) (0x13c2,0x0003).
<6>Intel(R) PRO/1000 Network Driver - version 7.6.5-NAPI
<6>Copyright (c) 1999-2007 Intel Corporation.
<4>DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X).
<4>adapter has MAC addr = 00:d0:5c:21:3d:89
<4>dvb-ttpci: gpioirq unknown type=0 len=0
<4>dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 8000261f
<4>dvb-ttpci: firmware @ card 0 supports CI link layer interface
<4>dvb-ttpci: Crystal audio DAC @ card 0 detected
<4>saa7146_vv: saa7146 (0): registered device video0 [v4l2]
<4>saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
<4>DVB: registering frontend 0 (ST STV0299 DVB-S)...
<6>input: DVB on-card IR receiver as /class/input/input6
<6>dvb-ttpci: found av7110-0.
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata2.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x5a data 128 in
<4> res 40/00:03:00:00:20/00:00:00:00:00/a0 Emask 0x4 (timeout)
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/44
<6>ata2: EH pending after completion, repeating EH (cnt=4)
<6>ata2: EH complete
<4>sr0: scsi-1 drive
<6>Uniform CD-ROM driver Revision: 3.20
<7>sr 1:0:0:0: Attached scsi CD-ROM sr0
<6>Adding 2048248k swap on /dev/sda10. Priority:-1 extents:1 across:2048248k
<6>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
<6>loop: module loaded
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda9, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda7, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<4>fuse init (API version 7.8)
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sdb4, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sdb2, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sdb3, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>AppArmor: AppArmor initialized
<5>audit(1213175255.970:2): type=1505 info="AppArmor initialized" pid=2222
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Wed Jun 11 09:05:50 2008

Creating device nodes with udev
Trying manual resume from /dev/sda10
Invoking userspace resume from /dev/sda10
resume: Could not stat configuration file
resume: libgcrypt version: 1.2.4
Trying manual resume from /dev/sda10
Invoking in-kernel resume from /dev/sda10
Waiting for device /dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 to appear: ok
fsck 1.40.2 (12-Jul-2007)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5
/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5: clean, 196157/1966976 files, 1674805/3933916 blocks
fsck succeeded. Mounting root device read-write.
Mounting root /dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5

Boot logging started on /dev/tty1(/dev/console (deleted)) at Wed Jun 11 11:06:59 2008

done
Starting udevd udevd-event[1852]: node_symlink: device node '/dev/rtc0' already exists, link '/dev/rtc' will not overwrite it

done
Loading required kernel modules
doneActivating swap-devices in /etc/fstab...
donemount: according to mtab, /dev/sda5 is already mounted on /

Activating device mapper...
done
Waiting for /dev/disk/by-id/usb-_TOSHIBA_USB_MEM_077614A1062F-0:0-part1 . no more events
Checking file systems...
fsck 1.40.2 (12-Jul-2007)
home_debian (/dev/disk/by-label/home_debian): clean, 15/5570560 files, 219908/11135045 blocks
/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part7: clean, 134425/25608192 files, 21488540/51199147 blocks (check in 2 mounts)
2nd_HDD_SATA (/dev/disk/by-id/scsi-SATA_Hitachi_HDP7250_GEA530RE1AA9SE-part4): clean, 74/52510720 files, 15185455/105006864 blocks
/dev/disk/by-id/scsi-SATA_Hitachi_HDP7250_GEA530RE1AA9SE-part2: clean, 12/640000 files, 56708/1279175 blocks
/dev/disk/by-id/scsi-SATA_Hitachi_HDP7250_GEA530RE1AA9SE-part3: clean, 11/5324800 files, 212194/10639046 blocks
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda9 on /home_debian type ext3 (rw,noexec,nosuid,nodev,acl)
/dev/sda7 on /home type ext3 (rw)
/dev/sda6 on /windows/D type vfat (rw,noexec,nosuid,nodev,gid=100,umask=0002,utf8=true)
mount: special device /dev/disk/by-id/usb-_TOSHIBA_USB_MEM_077614A1062F-0:0-part1 does not exist
/dev/sdb4 on /DATA_sdb4_400GB type ext3 (rw)
/dev/sdb2 on /sdb2_4.8GB type ext3 (rw,noexec,nosuid,nodev,acl)
/dev/sdb3 on /sdb3_40GB type ext3 (rw,noexec,nosuid,nodev,acl)
failedSetting up the hardware clockdone
Retry device configurationdone
Configuring serial ports...
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
/dev/ttyS1 at 0x1c88 (irq = 17) is a 16550A
Configured serial ports
doneSetting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
fs.inotify.max_user_watches = 65536
done
Mounting securityfs on /sys/kernel/security done
Loading AppArmor module done
Loading AppArmor profiles Activating remaining swap-devices in /etc/fstab...
done<notice>killproc: kill(1221,29)
Creating /var/log/boot.msg
doneEnabling syn flood protectiondone
Disabling IP forwardingdone
done
done
Setting up hostname 'c7'done
Setting up loopback interface lo
lo IP address: 127.0.0.1/8
Checking for network time protocol daemon (NTPD): unused
Can't determine current runlevel
done
System Boot Control: The system has been set up
Skipped features: boot.cycle
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(1221,3)

INIT: Entering runlevel: 5



Boot logging started on /dev/tty1(/dev/console) at Wed Jun 11 09:07:38 2008

Master Resource Control: previous runlevel: N, switching to runlevel: 5
Starting D-Bus daemonUnknown username "gdm" in message bus configuration file
done
Initializing random number generatordone
<notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=64 SHLVL=2 HOME=/ SPLASH=no splash=native ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
<notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/sbin/acpid ]
Checking/updating CPU microcode done
<notice>startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ]
Starting resource managerdone
Starting ConsoleKit<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=64 SHLVL=2 HOME=/ SPLASH=no splash=native ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/sbin/klogd ]
Starting syslog servicesdone
Starting acpid done
done
acpid: starting up


acpid: 0 rules loaded


Starting HAL daemon<notice>startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/hald ]
done
Loading CPUFreq modulesdone
Starting Firewall Initialization (phase 1 of 2) SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled.
done
Starting service kdm<notice>startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 SPLASHCFG= PWD=/ LANG=de_DE.UTF-8 PREVLEVEL=N LINES=64 QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/bin/kde SPLASH=no splash=native ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ]
done
<notice>startproc: execve (/usr/sbin/dhcdbd) [ /usr/sbin/dhcdbd --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/dhcdbd ]
<notice>startproc: execve (/usr/sbin/NetworkManagerDispatcher) [ /usr/sbin/NetworkManagerDispatcher ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManagerDispatcher ]
<notice>startproc: execve (/usr/sbin/NetworkManager) [ /usr/sbin/NetworkManager ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManager ]
Starting the DHCP DBUS Daemondone
Starting the NetworkManagerDispatcherdone
Starting the NetworkManagerdone
<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/sbin/portmap ]
Starting RPC portmap daemondone
Starting NFS client services: sm-notifyBackgrounding to notify hosts...
done
<notice>checkproc: /opt/kde3/bin/kdm 2788
Loading keymap i386/qwertz/de-latin1-nodeadkeys.map.gz
doneLoading compose table latin1.adddone
Start Unicode mode
doneLoading console font lat9w-16.psfu -m trivial G0:loadable
done<notice>checkproc: /opt/kde3/bin/kdm 2788
<notice>killproc: kill(2780,15)
<notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/sbin/auditd ]
Starting auditd done
<notice>startproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ]
Starting Avahi daemon.done
<notice>startproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ]
Starting Avahi DNS Configuration daemondone
<notice>startproc: execve (/usr/sbin/irqbalance) [ /usr/sbin/irqbalance ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/irqbalance ]
<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ]
Starting irqbalance done
<notice>startproc: execve (/usr/sbin/ntpd) [ /usr/sbin/ntpd -p /var/run/ntp/ntpd.pid -u ntp -i /var/lib/ntp ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/ntpd ]
Starting cupsddone
<notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ]
Try to get initial date and time via NTP from 0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.orgError : Temporary failure in name resolution
Error : Temporary failure in name resolution
Error : Temporary failure in name resolution
failed
Starting network time protocol daemon (NTPD)done
Starting powersaved: done
<notice>startproc: execve (/usr/sbin/rpc.mountd) [ /usr/sbin/rpc.mountd --no-nfs-version 4 ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/rpc.mountd ]
Starting SSH daemon<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
<notice>startproc: execve (/usr/sbin/rpc.statd) [ /usr/sbin/rpc.statd --no-notify ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/rpc.statd ]
done
Starting kernel based NFS server:exportfs: Warning: /media/ExternePlatte-1 does not exist
mountd statd nfsd sm-notifydone
Starting Name Service Cache Daemon<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
done
Starting mail service (Postfix)done
<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
Starting CRON daemondone
<notice>startproc: execve (/usr/sbin/smartd) [ /usr/sbin/smartd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=native SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFL261R83ZEL2N-part5 _=/sbin/startproc DAEMON=/usr/sbin/smartd ]
Starting smartd done
Starting Firewall Initialization (phase 2 of 2) SuSEfirewall2: Warning: no default firewall zone defined, assuming 'ext'
done
done
Master Resource Control: runlevel 5 has been reached
<notice>killproc: kill(2399,3)

Zum Vergrößern anklicken....