• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

USB WLAN Stick

Rolandor

Newbie
Hallo,

wie bekomme ich den USB-WLAN Stick von LogiLink unter openSuse 10.2 zum laufen?

Hat jemand evtl. Erfahrungen darüber, welcher Treiber?

Viele Grüße und Danke für Tipps
 
OP
R

Rolandor

Newbie
Hi,

hab den folgenden Treiber installiert:

rtl8187-kmp-default (20070806_2.6.22.5_31)
Kernel Module for Realtek RTL8187 USB adapters

Trotzdem wird der USB-WLAN Stick nicht als Netzwerkkarte oder ähnliches erkannt. :-(

Viele Grüße
 
OP
R

Rolandor

Newbie
Hi,

die Ausgabe zu dmesg:

dmesg
Code:
Linux version 2.6.22.5-31-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2007/09/21 22:29:00 UTC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
 BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
256MB LOWMEM available.
Entering add_active_range(0, 0, 65536) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    65536
  HighMem     65536 ->    65536
early_node_map[1] active PFN ranges
    0:        0 ->    65536
On node 0 totalpages: 65536
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 480 pages used for memmap
  Normal zone: 60960 pages, LIFO batch:15
  HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Built 1 zonelists.  Total pages: 65024
Kernel command line: root=/dev/disk/by-id/scsi-SATA_MAXTOR_4K040H2_572122617095-part2 vga=0x31a    resume=/dev/sda1 splash=silent
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0120c000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 1327.746 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 251880k/262144k available (1825k kernel code, 9696k reserved, 764k data, 228k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffdf4000 - 0xfffff000   (2092 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xd0800000 - 0xff7fe000   ( 751 MB)
    lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
      .init : 0xc038e000 - 0xc03c7000   ( 228 kB)
      .data : 0xc02c86ed - 0xc0387964   ( 764 kB)
      .text : 0xc0100000 - 0xc02c86ed   (1825 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2656.92 BogoMIPS (lpj=5313849)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
Unpacking initramfs... done
Freeing initrd memory: 4041k freed
ACPI: Core revision 20070126
ACPI Exception (tbxface-0618): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126]
ACPI: Unable to load the System Description Tables
CPU0: AMD Athlon(tm) Processor stepping 04
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7210
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x5ed7, dseg 0xf0000
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Enabling SiS 96x SMBus.
PCI: Using IRQ router SIS [1039/0018] at 0000:00:02.0
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:02.1
PCI: Sharing IRQ 11 with 0000:00:0b.0
ACPI Error (evxfevnt-0186): Could not enable RealTimeClock event [20070126]
ACPI Warning (evxface-0145): Could not enable fixed event 4 [20070126]
pnp: 00:01: iomem range 0x0-0x9fbff could not be reserved
pnp: 00:01: iomem range 0x9fc00-0x9ffff could not be reserved
pnp: 00:01: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:01: iomem range 0x100000-0xfffffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: cde00000-cfefffff
  PREFETCH window: bdc00000-cdcfffff
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 98304 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1196499647.360:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
vesafb: framebuffer at 0xc0000000, mapped to 0xd0880000, using 10240k, total 65536k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:0f3e
vesafb: pmi: set display start = c00c0f77, set palette = c00c0fed
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 98233 bytes
bootsplash: ...found (1280x1024, 35219 bytes, v3).
Console: switching to colour frame buffer device 156x60
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
NET: Registered protocol family 1
Using IPI No-Shortcut mode
Freeing unused kernel memory: 228k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_sis 0000:00:02.5: version 0.5.2
scsi0 : pata_sis
scsi1 : pata_sis
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ff00 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ff08 irq 15
ata1.00: ATA-5: MAXTOR 4K040H2, A08.1500, max UDMA/100
ata1.00: 78198750 sectors, multi 16: LBA
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: configured for UDMA/33
ata2.00: ATAPI: SAMSUNG CD-R/RW DRIVE SW-248B, R500, max UDMA/33
ata2.01: ATAPI: TSSTcorpDVD-ROM SH-D162D, SB00, max UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      MAXTOR 4K040H2   A08. PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            SAMSUNG  CD-R/RW SW-248B  R500 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM            TSSTcorp DVD-ROM SH-D162D SB00 PQ: 0 ANSI: 5
thermal: Unknown symbol acpi_processor_set_thermal_limit
Clocksource tsc unstable (delta = 100013451 ns)
Time: pit clocksource has been installed.
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: setting IRQ 5 as level-triggered
PCI: Found IRQ 5 for device 0000:00:02.2
ohci_hcd 0000:00:02.2: OHCI Host Controller
ohci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.2: irq 5, io mem 0xcfffe000
sd 0:0:0:0: [sda] 78198750 512-byte hardware sectors (40038 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 78198750 512-byte hardware sectors (40038 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<6>usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22.5-31-default ohci_hcd
usb usb1: SerialNumber: 0000:00:02.2
 sda1 sda2 sda3
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
sd 0:0:0:0: [sda] Attached SCSI disk
PCI: Found IRQ 11 for device 0000:00:02.3
ohci_hcd 0000:00:02.3: OHCI Host Controller
ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.3: irq 11, io mem 0xcffff000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22.5-31-default ohci_hcd
usb usb2: SerialNumber: 0000:00:02.3
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 1-1: new full speed USB device using ohci_hcd and address 2
usb 1-1: new device found, idVendor=0bda, idProduct=8187
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: RTL8187B_WLAN_Adapter
usb 1-1: Manufacturer: Manufacturer_Realtek
usb 1-1: SerialNumber: 00e04c000001
usb 1-1: configuration #1 chosen from 1 choice
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Linux agpgart interface v0.102 (c) Dave Jones
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:05 failed with error -16
agpgart: Detected SiS chipset - id:1845
agpgart: AGP aperture is 64M @ 0xd0000000
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
gameport: NS558 PnP Gameport is pnp00:0b/gameport0, io 0x201, speed 670kHz
8139too Fast Ethernet driver 0.9.28
PCI: Found IRQ 11 for device 0000:00:0b.0
PCI: Sharing IRQ 11 with 0000:00:02.1
eth0: RealTek RTL8139 at 0xd15f6f00, 00:50:bf:6a:ea:d7, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8139C'
sr0: scsi3-mmc drive: 48x/1x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 62x/62x cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
parport_pc 00:0d: reported by Plug and Play BIOS
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
rtl8187: no version for "eeprom_93cx6_multiread" found: kernel tainted.
sis630_smbus 0000:00:02.0: SIS630 comp. bus not detected, module not inserted.
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
PCI: Found IRQ 11 for device 0000:00:02.7
intel8x0_measure_ac97_clock: measured 52827 usecs
intel8x0: clocking to 48000
wmaster0: Selected rate control algorithm 'simple'
phy0: hwaddr 00:0e:2e:e7:45:af, rtl8187 V0 + rtl8225
usbcore: registered new interface driver rtl8187
Adding 514040k swap on /dev/sda1.  Priority:-1 extents:1 across:514040k
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
loop: module loaded
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor initialized
audit(1196499661.476:2):  type=1505 info="AppArmor initialized" pid=1568
powernow_k8: Unknown symbol acpi_processor_notify_smm
powernow_k8: Unknown symbol acpi_processor_unregister_performance
powernow_k8: Unknown symbol acpi_processor_register_performance
powernow_k7: Unknown symbol acpi_processor_notify_smm
powernow_k7: Unknown symbol acpi_processor_unregister_performance
powernow_k7: Unknown symbol acpi_processor_register_performance
acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
acpi_cpufreq: Unknown symbol acpi_processor_register_performance
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
eth0: no IPv6 routers present
audit(1196496103.009:3): audit_pid=3309 old=0 by auid=4294967295
bootsplash: status on console 0 changed to on

iwconfig
Code:
iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11g  ESSID:""
          Mode:Managed  Channel:0  Access Point: Not-Associated
          Retry min limit:7   RTS thr:off   Fragment thr=2346 B
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Soweit die Ausgaben. Trotzdem wird der USB WLAN Stick nicht als Netzwerkdevice erkannt. :-(

Viele Grüße
 

Grothesk

Ultimate Guru
Warum?
Da ist er doch:
Code:
wlan0     IEEE 802.11g  ESSID:"" 
           Mode:Managed  Channel:0  Access Point: Not-Associated 
           Retry min limit:7   RTS thr:off   Fragment thr=2346 B 
           Encryption key:off 
           Link Quality:0  Signal level:0  Noise level:0 
           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 
           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
Taucht der im NetworkManager nicht auf?

Code:
iwlist scan
sagt was?
 
OP
R

Rolandor

Newbie
Hi,

im yast2 unter Netzwerkgeräte taucht er leider nicht auf.

Hier die seltsamen Ausgaben:

Code:
linux:~ # iwlist scan
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning.

wlan0     Interface doesn't support scanning : Network is down

linux:~ # ifconfig wlan0 up
SIOCSIFFLAGS: Connection timed out
linux:~ # ifconfig wlan0 up
wlan0: unknown interface: No such device
linux:~ # iwlist scan
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

Viele Grüße
 
OP
R

Rolandor

Newbie
Hi,

was mich auch verwundert ist, das der USB-WLAN Stick nach der Statistik nicht versucht hat zu senden.

Bin nach wie vor dankbar für Tipps.

Viele Grüße
 
OP
R

Rolandor

Newbie
Hi,

habe jetzt sowohl per Konfiguration über yast als auch iwconfig probiert.

Bei beiden hatte ich keinen Erfolg.

Hat jemand ein ähnliches Problem gehabt?

Viele Grüße
 
Oben