• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

Problem mit ACPI, Suse 10.3 auf Thinkpad R51e

O

oeliii

Newbie
Hallo,

Ich habe kürzlich den umstieg von Suse 10.2 auf Suse 10.3 gemacht. Läuft soweit ganz gut,nur das ACPI macht Probleme. Der Rechner braucht beim booten extrem lange, er hängt wenn er Ausgaben zu ACPI (Lüfter und Stromversorgung) macht, im Betrieb wird keine angabe gemacht, ob Akku oder Netzbetrieb und auch keine zum Ladezustand des Akkus.
Die Optionen Suspend to RAM/Disk funtionieren ebenfalls nicht.

Mit acpi=off bootet er sehr schnell, kann aber beim herunterfahren nicht automatisch ausschalten. Die Angaben zu Stromversorgung bekomme ich auch nicht.

Unter 10.2 war das alles kein Problem. Kann mir jemand helfen?

Vielen Dank!
mfg
oeliii
 
onkelchentobi

onkelchentobi

Guru
Du kannst dir mal die /var/log Dateien ansehen und die genauen Ausgaben posten zwecks dem langen haengen beim Bootvorgang und dem ACPI.
 
OP
O

oeliii

Newbie
OnkelchenTobi schrieb:
Du kannst dir mal die /var/log Dateien ansehen und die genauen Ausgaben posten zwecks dem langen haengen beim Bootvorgang und dem ACPI.
Zum Vergrößern anklicken....

Hallo,

da gibt es einige Dateien, in welchen steht denn das wichtige drin und was soll ich posten? Ich bin da nicht so versiert!
 
onkelchentobi

onkelchentobi

Guru
Als root ein dmesg eingeben.

Es mag sein das unter SuSE die Verzeichnisstrucktur ein wenig anderst ist als bei mir. Schau einfach mal was in /var/log nach, vl. ist da auch eine boot.msg oder so.
 
OP
O

oeliii

Newbie
Die Eingabe von dmesg fördert dies zutage. Eine boot.msg gibt es auch, soll ich die auch posten?

linux-7rh9:~ # dmesg
Linux version 2.6.22.12-0.1-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2007/11/06 23:05:18 UTC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000099000 (usable)
BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000057ee0000 (usable)
BIOS-e820: 0000000057ee0000 - 0000000057eeb000 (ACPI data)
BIOS-e820: 0000000057eeb000 - 0000000057f00000 (ACPI NVS)
BIOS-e820: 0000000057f00000 - 0000000058000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
PCI: Unknown option `noapci'
510MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 360160) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 360160
early_node_map[1] active PFN ranges
0: 0 -> 360160
On node 0 totalpages: 360160
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 1021 pages used for memmap
HighMem zone: 129763 pages, LIFO batch:31
DMI present.
Using APIC driver default
ACPI: RSDP 000F6C80, 0024 (r2 IBM )
ACPI: XSDT 57EE186C, 0054 (r1 IBM TP-78 1610 LTP 0)
ACPI: FACP 57EE1900, 00F4 (r3 IBM TP-78 1610 IBM 1)
ACPI Error (tbfadt-0453): 32/64X address mismatch in "Gpe0Block": [00008020] [0000000000008028], using 64X [20070126]
ACPI: DSDT 57EE1AE7, 92C8 (r1 IBM TP-78 1610 MSFT 100000E)
ACPI: FACS 57EEC000, 0040
ACPI: SSDT 57EE1AB4, 0033 (r1 IBM TP-78 1610 MSFT 100000E)
ACPI: ECDT 57EEADAF, 0052 (r1 IBM TP-78 1610 IBM 1)
ACPI: APIC 57EEAE01, 005A (r1 IBM TP-78 1610 IBM 1)
ACPI: MCFG 57EEAE5B, 003E (r1 IBM TP-78 1610 IBM 1)
ACPI: BOOT 57EEAFD8, 0028 (r1 IBM TP-78 1610 LTP 1)
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 60000000 (gap: 58000000:88000000)
Built 1 zonelists. Total pages: 357347
Kernel command line: root=/dev/disk/by-id/scsi-SATA_TOSHIBA_MK1234G_774QT0TOT-part8 vga=0x317 resume=/dev/sda6 splash=silent showopts apm=off pci=noapci
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1495.698 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1419900k/1440640k available (1825k kernel code, 19492k reserved, 765k data, 228k init, 523136k highmem)
virtual kernel memory layout:
fixmap : 0xffdf4000 - 0xfffff000 (2092 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc038e000 - 0xc03c7000 ( 228 kB)
.data : 0xc02c842b - 0xc0387964 ( 765 kB)
.text : 0xc0100000 - 0xc02c842b (1825 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2994.94 BogoMIPS (lpj=5989884)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
Unpacking initramfs... done
Freeing initrd memory: 4020k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1097 Objects with 57 Devices 323 Methods 14 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 1 Objects with 0 Devices 1 Methods 0 Regions
tbxface-0587 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
CPU0: Intel(R) Celeron(R) M processor 1.50GHz stepping 08
Total of 1 processors activated (2994.94 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x15
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 5 Wake, Enabled 1 Runtime GPEs in this block
ACPI: EC: EC description table is found, configuring boot EC

Completing Region/Field/Buffer/Package initialization:....................................................................................................................................
Initialized 14/14 Regions 26/26 Fields 37/37 Buffers 55/67 Packages (1107 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:....
Executed 4 _INI methods requiring 0 _STA executions (examined 61 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: Power Resource [PUBS] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:06.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:06.0
ACPI: RTC can wake from S4
pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:02: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:02: iomem range 0xfff80000-0xffffffff has been reserved
pnp: 00:02: iomem range 0x0-0xfff could not be reserved
pnp: 00:03: ioport range 0x1080-0x1080 has been reserved
pnp: 00:03: ioport range 0x220-0x22f has been reserved
pnp: 00:03: ioport range 0x3bf-0x3bf has been reserved
pnp: 00:03: ioport range 0x7bf-0x7bf has been reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: a0100000-a01fffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: a0200000-a02fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bus 5, cardbus bridge: 0000:04:00.0
IO window: 0000a000-0000a0ff
IO window: 0000a400-0000a4ff
PREFETCH window: d0000000-d3ffffff
MEM window: a4000000-a7ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-dfff
MEM window: a0300000-afffffff
PREFETCH window: d0000000-d7ffffff
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 20 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x35 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1195243196.876:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:05.0
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
Allocate Port Service[0000:00:06.0:pcie03]
Evaluate _OSC Set fails. Status = 0x0005
Evaluate _OSC Set fails. Status = 0x0005
aer_init: AER service init fails - Run ACPI _OSC fails
aer: probe of 0000:00:04.0:pcie01 failed with error 2
Evaluate _OSC Set fails. Status = 0x0005
Evaluate _OSC Set fails. Status = 0x0005
aer_init: AER service init fails - Run ACPI _OSC fails
aer: probe of 0000:00:06.0:pcie01 failed with error 2
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 6144k, total 131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=84
vesafb: protected mode interface info at c000:5191
vesafb: pmi: set display start = c00c51ff, set palette = c00c5239
vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 78436 bytes
bootsplash: ...found (1024x768, 28133 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to NOHz mode on CPU #0
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt 0000:00:14.6 -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:14.6 disabled
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input2
NET: Registered protocol family 1
Using IPI No-Shortcut mode
Freeing unused kernel memory: 228k freed
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU] (supports 8 throttling states)
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Clocksource tsc unstable (delta = -207044785 ns)
ACPI: Thermal Zone [THM0] (53 C)
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:14.1 to 64
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00018410 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00018418 irq 15
ata1.00: ATA-6: TOSHIBA MK1234GAX, AC001A, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata2.00: ATAPI: MATSHITADVD-RAM UJ-830Sx, 1.00, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1234GA AC00 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-830Sx 1.00 PQ: 0 ANSI: 5
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 9 (level, low) -> IRQ 9
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 9, io mem 0xa0000000
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22.12-0.1-default ohci_hcd
usb usb1: SerialNumber: 0000:00:13.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 9 (level, low) -> IRQ 9
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: irq 9, io mem 0xa0002000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22.12-0.1-default ehci_hcd
usb usb2: SerialNumber: 0000:00:13.2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 9 (level, low) -> IRQ 9
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 9, io mem 0xa0001000
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.22.12-0.1-default ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:07 failed with error -16
tg3.c:v3.77 (May 31, 2007)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Tigon3 [partno(BCM95751F) rev 4201 PHY(5750)] (PCI Express) 10/100Base-TX Ethernet 00:0a:e4:3b:ae:d4
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
Linux agpgart interface v0.102 (c) Dave Jones
Non-volatile memory driver v1.2
thinkpad_acpi: ThinkPad ACPI Extras v0.14
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 78ET71WW (1.61 ), EC 78HT05WW-1.00
thinkpad_acpi: IBM ThinkPad R51e
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: PCI Interrupt 0000:00:14.6 -> GSI 17 (level, low) -> IRQ 17
wlan: 0.8.4.2 (0.9.3.2)
ath_pci: 0.9.4.5 (0.9.3.2)
ALSA sound/pci/ac97/ac97_codec.c:2145: MC'97 1 converters and GPIO not ready (0xff00)
ACPI: PCI Interrupt 0000:00:14.5 -> GSI 17 (level, low) -> IRQ 17
[fglrx] Maximum main memory to use for locked dma buffers: 1292 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.42.3 [Oct 19 2007] on minor 0
Yenta: CardBus bridge found at 0000:04:00.0 [1410:0528]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:04:00.0, mfunc 0x01d21002, devctl 0x64
Yenta: ISA IRQ mask 0x0c78, PCI irq 16
Socket status: 30000007
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xdfff
cs: IO port probe 0xa000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xa0300000 - 0xafffffff
pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd7ffffff
ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 22 (level, low) -> IRQ 19
ath_rate_sample: 1.2 (0.9.3.2)
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.9 phy 4.3 radio 4.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xa0300000, irq=19
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
cs: IO port probe 0xa00-0xaff: clean.
thinkpad_acpi: fan_init: initial fan status is unknown, assuming it is in auto mode
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SLPB]
ACPI: AC Adapter [AC] (on-line)
ACPI Error (evgpe-0705): No handler or method for GPE[ 0], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 1], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 2], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 4], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 5], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 8], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 9], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ A], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ C], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ D], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ E], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ F], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[10], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[11], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[13], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[14], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[15], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[16], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[17], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[18], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[19], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1A], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1B], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1C], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1D], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1E], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1F], disabling event [20070126]
ACPI: Battery Slot [BAT0] (battery present)
Adding 2101640k swap on /dev/sda6. Priority:-1 extents:1 across:2101640k
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
loop: module loaded
fuse init (API version 7.8)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor initialized
audit(1195243308.657:2): type=1505 info="AppArmor initialized" pid=1861
ACPI Error (evgpe-0705): No handler or method for GPE[ 0], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 1], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 2], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 4], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 5], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 8], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ 9], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ A], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ C], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ D], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ E], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[ F], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[10], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[11], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[13], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[14], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[15], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[16], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[17], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[18], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[19], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1A], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1B], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1C], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1D], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1E], disabling event [20070126]
ACPI Error (evgpe-0705): No handler or method for GPE[1F], disabling event [20070126]
powernow: This module only works with AMD K7 CPUs
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
NET: Registered protocol family 17
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
PM: Writing back config space on device 0000:02:00.0 at offset 1 (was 100506, writing 100106)
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1195239734.806:3): audit_pid=3473 old=0 by auid=4294967295
ath0: no IPv6 routers present
input: /usr/sbin/acpi-keys as /class/input/input6
bootsplash: status on console 0 changed to on
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC= SRC=192.168.2.26 DST=224.0.0.251 LEN=414 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=394
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC= SRC=192.168.2.26 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC= SRC=192.168.2.26 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC= SRC=192.168.2.26 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC= SRC=192.168.2.26 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC=01:00:5e:00:00:01:00:1a:4f:45:00:cb:08:00 SRC=192.168.2.1 DST=224.0.0.1 LEN=36 TOS=0x00 PREC=0x80 TTL=1 ID=293 DF OPT (94040000) PROTO=2
SFW2-INext-DROP-DEFLT IN=ath0 OUT= MAC= SRC=192.168.2.26 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
 
OP
O

oeliii

Newbie
Hast Du einen Tipp, ob es ein bestimmter sein soll, oder hauptsache älter als 2.6.2x.x also z.B. irgendwas mit 2.6.1x.x.

Ich habe noch nie einen Kernel kompiliert, hast Du einen Tipp für eine gute Anleitung? Ich scheue mich ein wenig vor den ganzen Einstellungen, die da gefordert werden.

Vielen Dank schonmal
 
onkelchentobi

onkelchentobi

Guru
Du musst keinen Kernel selber bauen, spiele einen fertigen ein. Ich habe im Netz nur bereits des oeffteren gelesen das es gerade bei den momentan neueren Kernelversionen wieder des oeffteren Probs. mit ACPI gibt, gerade bei Thinkpads. Daher wuerde ich das mal mit einem anderen versuchen. Schau mal auf deine SuSE Detentraeger was da noch alles fuer welche mit dabei sind die dann bequem ueber Yast installiert werden koennen. Aber immer daran denken das du keinen Kernel vom System deinstallierst ! Genau genommen solltest du dir einen zweiten mit dazu installieren. Schau hierzu mal ins Wiki, dort sollte etwas zu finden sein.

http://wiki.linux-club.de/Kernel
 
OP
O

oeliii

Newbie
Ich habe jetzt einen Kernel 2.6.18.2-34 (von der Suse 10.2 DVD) per "rpm -ihv --oldpackage kernel-default-2.6.18.2-34.i586.rpm" eingespielt. Es ist auch gleich ein zusätzlicher Eintrag in Grub angelegt worden.
Beim booten bleibt das System allerdings hängen mit einer Meldung: waiting for sda8 (oder so ähnlich).
Das booten mit dem vorherigen Kernel geht problemlos. Die Einträge in der /boot/grub/menu.lst sind bis auf die Kernelnummer identisch, siehe unten:

# Modified by YaST2. Last modification on Mo Nov 19 20:57:07 CET 2007
default 3
timeout 8
gfxmenu (hd0,7)/boot/message

###Don't change this comment - YaST2 identifier: Original name: linux###
title openSUSE 10.3 - 2.6.18.2-34
root (hd0,7)
kernel /boot/vmlinuz-2.6.18.2-34-default root=/dev/disk/by-id/scsi-SATA_TOSHIBA_MK1234G_774QT0TOT-part8 vga=0x317 resume=/dev/sda6 splash=silent showopts acpi_irq_balance
initrd /boot/initrd-2.6.18.2-34-default

###Don't change this comment - YaST2 identifier: Original name: linux-2.6.22.12-0.1-default###
title openSUSE 10.3 - 2.6.22.12-0.1
root (hd0,7)
kernel /boot/vmlinuz-2.6.22.12-0.1-default root=/dev/disk/by-id/scsi-SATA_TOSHIBA_MK1234G_774QT0TOT-part8 vga=0x317 resume=/dev/sda6 splash=silent showopts acpi_irq_balance
initrd /boot/initrd-2.6.22.12-0.1-default
 
P

pweber

Newbie
Das Problem, dass Kpowersave immer nur den Wechselstromanschluss angezeigt hat, obwohl ich im Akkubetrieb unterwegs war hatte ich auch. Ich habe dann mit "acpi=force" gestartet und plötzlich wechselt Kpowersave das Icon.

BTW, ich verwende auf meinem IBM ThinkPad X20 mit 384 MB RAM openSUSE 10.3. Ich konnte noch nicht feststellen, dass das Booten oder Herunterfahren schneller geht als vorher mit 10.2.
 
OP
O

oeliii

Newbie
Ich habe jetzt festgestellt, dass, wenn ich mit normaler acpi Option boote (acpi=force bringt keinen unterschied), dass KPowersave Icon die richtigen Werte anzeigt, aber nur wenn ich den X-Server einmal neustarte (Strg+Alt+Backspace) oder mich einmal ein- und auslogge.

Mit aktiviertem acpi geht das booten sehr langsam, mit acpi=off sehr schnell, auch deutlich schneller als bei Opensuse 10.2.

Jezt habe ich gerade nochmal die acpi=oldboot Option ausprobiert, da hängt der Rechner deutlich kürzer beim booten. Ich habe auch nicht den Eindruck, dass acpi nicht funktioniert, sondern nur extrem langsam. Wenn ich in der Konsole den Status mit acpi -V abrufe dauert es etwa 2 Minuten, bis ich die Ausgabe bekomme. Ist das normal?
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben