Every 1,0s: dmesg | tail Tue Sep 29 09:10:38 2009
usb 5-2: Product: EyeToy USB camera Namtai
usb 5-2: Manufacturer: Sony corporation
gspca: main v2.7.0 registered
gspca: probing 054c:0155
ov519: I2C synced in 0 attempt(s)
ov519: starting OV7xx0 configuration
ov519: Sensor is an OV7648
gspca: probe ok
usbcore: registered new interface driver ov519
ov519: registered
hwinfo --usb
23: USB 00.0: 0000 Unclassified device
[Created at usb.122]
UDI: /org/freedesktop/Hal/devices/usb_device_54c_155_noserial_if0
Unique ID: wn1q.Tjn4iaXZW80
Parent ID: 2XnU.Oz8tSgc5mXF
SysFS ID: /devices/pci0000:00/0000:00:10.3/usb5/5-2/5-2:1.0
SysFS BusID: 5-2:1.0
Hardware Class: unknown
Model: "Sony EyeToy USB camera Namtai"
Hotplug: USB
Vendor: usb 0x054c "Sony Corp."
Device: usb 0x0155 "EyeToy USB camera Namtai"
Revision: "1.00"
Driver: "ov519"
Driver Modules: "gspca_ov519"
Speed: 12 Mbps
Module Alias: "usb:v054Cp0155d0100dc00dsc00dp00icFFisc00ip00"
Driver Info #0:
Driver Status: gspca_ov519 is active
Driver Activation Cmd: "modprobe gspca_ov519"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #14 (Hub)
lsusb -v
lsmod
Module Size Used by
gspca_ov519 24444 0
gspca_main 25848 1 gspca_ov519
Mein englisch ist zwar nicht ganz schlecht aber wenn ich das richtig verstehe dann hat der Author die Arbeit daran eingestellt weil es in künftigen Kernel Versionen schon eingebaut sein soll.misiu schrieb:Vielleicht findest du da was hilfreiches:
Pidgin habe ich versucht aber da scheint gar keine Webcam Funktion vorhanden zu sein. Welche Software kann ich noch benutzen?misiu schrieb:Hast du schon andere Webcam-Programme versucht?
[/quote]Pidgin habe ich versucht aber da scheint gar keine Webcam Funktion vorhanden zu sein. Welche Software kann ich noch benutzen?misiu schrieb:Hast du schon andere Webcam-Programme versucht?
lieben Gruß aus Hessen
keines dieser Programme ist in meinen Repositorys zu finden :???: andere Dateinamen?misiu schrieb:Cheese, Skype, lvcview.
** ERROR **: building ui from /usr/share/cheese/cheese.ui failed: /usr/share/cheese/cheese.ui: required gtk+ version 2.16, current version is 2.14
aborting...
Herz-von-Hessen schrieb:required gtk+ version 2.16, current version is 2.14
aborting...[/code]
naja, hier steht was dir fehlt bzw was du in der falschen Version installiert Hast. Schau mal ob du dies mittels yast upgraden kannst auf die benötigte 2.16er Version.
Ich habe in YAST gtk als Suchbegriff eingegeben und alle installierten Pakete aktualisieren lassen.Jägerschlürfer schrieb:naja, hier steht was dir fehlt bzw was du in der falschen Version installiert Hast. Schau mal ob du dies mittels yast upgraden kannst auf die benötigte 2.16er Version.
(cheese:2439): GStreamer-WARNING **: pad source:src returned caps which are not a real subset of its template caps
(cheese:2439): GStreamer-CRITICAL **: gst_value_set_fraction: assertion `denominator != 0' failed
(cheese:2439): GStreamer-WARNING **: pad source:src returned caps which are not a real subset of its template caps
(cheese:2439): GStreamer-CRITICAL **: gst_value_set_fraction: assertion `denominator != 0' failed
(cheese:2439): GStreamer-CRITICAL **: gst_value_set_fraction: assertion `denominator != 0' failed
Die EyToy kann nur eingesteckt oder abgezogen werdenmisiu schrieb:Dann spiele etwas mit der Webcam :
1. an-/ausmachen
2. Webcamprogramme starten
misiu schrieb:Meldungen beobachten und evtl. hier rein-stellen.
tail -f /var/log/messages
Sep 30 11:38:38 dhcppc1 smartd[4018]: Device: /dev/sdb [SAT], SMART Usage Attribute: 199 UDMA_CRC_Error_Count changed from 196 to 184
Sep 30 11:40:33 dhcppc1 ntpd[3899]: kernel time sync status change 4001
Sep 30 12:08:26 dhcppc1 syslog-ng[2156]: Log statistics; dropped='pipe(/dev/xconsole)=0', dropped='pipe(/dev/tty10)=0', processed='center(queued)=325', processed='center(received)=318', processed='destination(newsnotice)=0', processed='destination(acpid)=0', processed='destination(firewall)=284', processed='destination(null)=0', processed='destination(mail)=0', processed='destination(mailinfo)=0', processed='destination(console)=0', processed='destination(newserr)=0', processed='destination(newscrit)=0', processed='destination(messages)=34', processed='destination(mailwarn)=0', processed='destination(localmessages)=1', processed='destination(netmgm)=0', processed='destination(mailerr)=0', processed='destination(xconsole)=0', processed='destination(warn)=6', processed='source(src)=318'
Sep 30 12:08:37 dhcppc1 smartd[4018]: Device: /dev/sdb [SAT], 48 Offline uncorrectable sectors
Sep 30 12:08:37 dhcppc1 smartd[4018]: Device: /dev/sdb [SAT], SMART Usage Attribute: 199 UDMA_CRC_Error_Count changed from 184 to 160
Sep 30 12:08:38 dhcppc1 smartd[4018]: Device: /dev/sdc [SAT], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 58 to 59
Sep 30 12:08:38 dhcppc1 smartd[4018]: Device: /dev/sdc [SAT], SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 58 to 59
Sep 30 12:14:40 dhcppc1 ntpd[3899]: kernel time sync status change 0001
Sep 30 12:15:01 dhcppc1 run-crons[8757]: mcelog: OK
Sep 30 12:17:00 dhcppc1 su: (to root) joerg on /dev/pts/1
Sep 30 12:17:33 dhcppc1 kernel: usb 5-2: USB disconnect, address 7
Sep 30 12:17:33 dhcppc1 kernel: gspca: disconnect complete
Sep 30 12:17:39 dhcppc1 kernel: usb 5-2: new full speed USB device using uhci_hcd and address 8
Sep 30 12:17:39 dhcppc1 kernel: usb 5-2: configuration #1 chosen from 1 choice
Sep 30 12:17:40 dhcppc1 kernel: gspca: probing 054c:0155
Sep 30 12:17:40 dhcppc1 kernel: ov519: I2C synced in 0 attempt(s)
Sep 30 12:17:40 dhcppc1 kernel: ov519: starting OV7xx0 configuration
Sep 30 12:17:40 dhcppc1 kernel: ov519: Sensor is an OV7648
Sep 30 12:19:10 dhcppc1 kernel: gspca: probe ok
Sep 30 12:19:10 dhcppc1 kernel: usb 5-2: New USB device found, idVendor=054c, idProduct=0155
Sep 30 12:19:10 dhcppc1 kernel: usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 30 12:19:10 dhcppc1 kernel: usb 5-2: Product: EyeToy USB camera Namtai
Sep 30 12:19:10 dhcppc1 kernel: usb 5-2: Manufacturer: Sony corporation
Sep 30 12:30:09 dhcppc1 kernel: usb 5-2: USB disconnect, address 12
Sep 30 12:30:09 dhcppc1 kernel: gspca: disconnect complete
Sep 30 12:30:15 dhcppc1 kernel: usb 5-2: new full speed USB device using uhci_hcd and address 13
Sep 30 12:30:15 dhcppc1 kernel: usb 5-2: configuration #1 chosen from 1 choice
Sep 30 12:30:15 dhcppc1 kernel: gspca: probing 054c:0155
Sep 30 12:30:15 dhcppc1 kernel: ov519: I2C synced in 0 attempt(s)
Sep 30 12:30:15 dhcppc1 kernel: ov519: starting OV7xx0 configuration
Sep 30 12:30:15 dhcppc1 kernel: ov519: Sensor is an OV7648
Sep 30 12:30:15 dhcppc1 kernel: gspca: probe ok
Sep 30 12:30:15 dhcppc1 kernel: usb 5-2: New USB device found, idVendor=054c, idProduct=0155
Sep 30 12:30:15 dhcppc1 kernel: usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 30 12:30:15 dhcppc1 kernel: usb 5-2: Product: EyeToy USB camera Namtai
Sep 30 12:30:15 dhcppc1 kernel: usb 5-2: Manufacturer: Sony corporation
Sep 30 12:38:37 dhcppc1 smartd[4018]: Device: /dev/sdb [SAT], 48 Offline uncorrectable sectors
Sep 30 12:38:37 dhcppc1 smartd[4018]: Device: /dev/sdb [SAT], SMART Prefailure Attribute: 8 Seek_Time_Performance changed from 248 to 249
Sep 30 12:38:37 dhcppc1 smartd[4018]: Device: /dev/sdb [SAT], SMART Usage Attribute: 199 UDMA_CRC_Error_Count changed from 160 to 187
Sep 30 12:38:37 dhcppc1 smartd[4018]: Device: /dev/sdc [SAT], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 59 to 58
Sep 30 12:38:37 dhcppc1 smartd[4018]: Device: /dev/sdc [SAT], SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 59 to 58
Sep 30 12:42:24 dhcppc1 kernel: usb 5-2: USB disconnect, address 14
Sep 30 12:42:24 dhcppc1 kernel: gspca: disconnect complete
Sep 30 12:42:27 dhcppc1 kernel: usb 5-2: new full speed USB device using uhci_hcd and address 15
Sep 30 12:42:27 dhcppc1 kernel: usb 5-2: configuration #1 chosen from 1 choice
Sep 30 12:42:27 dhcppc1 kernel: gspca: probing 054c:0155
Sep 30 12:42:28 dhcppc1 kernel: ov519: I2C synced in 0 attempt(s)
Sep 30 12:42:28 dhcppc1 kernel: ov519: starting OV7xx0 configuration
Sep 30 12:42:28 dhcppc1 kernel: ov519: Sensor is an OV7648
Sep 30 12:42:28 dhcppc1 kernel: gspca: probe ok
Sep 30 12:42:28 dhcppc1 kernel: usb 5-2: New USB device found, idVendor=054c, idProduct=0155
Sep 30 12:42:28 dhcppc1 kernel: usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 30 12:42:28 dhcppc1 kernel: usb 5-2: Product: EyeToy USB camera Namtai
Sep 30 12:42:28 dhcppc1 kernel: usb 5-2: Manufacturer: Sony corporation
** (cheese:9999): WARNING **: could not generate thumbnail for /home/joerg/.gnome2/cheese/media/2009-09-30-124058.ogv (video/ogg)
(cheese:9999): GStreamer-WARNING **: pad source:src returned caps which are not a real subset of its template caps
(cheese:9999): GStreamer-CRITICAL **: gst_value_set_fraction: assertion `denominator != 0' failed
(cheese:9999): GStreamer-WARNING **: pad source:src returned caps which are not a real subset of its template caps
(cheese:9999): GStreamer-CRITICAL **: gst_value_set_fraction: assertion `denominator != 0' failed
(cheese:9999): GStreamer-CRITICAL **: Failed to deactivate pad source:src, very bad
Sep 30 12:56:58 dhcppc1 kernel: usb 5-2: new full speed USB device using uhci_hcd and address 21
Sep 30 12:56:58 dhcppc1 kernel: usb 5-2: configuration #1 chosen from 1 choice
Sep 30 12:56:58 dhcppc1 kernel: usb 5-2: New USB device found, idVendor=046d, idProduct=0920
Sep 30 12:56:58 dhcppc1 kernel: usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Sep 30 12:56:58 dhcppc1 kernel: gspca: probing 046d:0920
Sep 30 12:56:58 dhcppc1 kernel: gspca: probe ok
Sep 30 12:56:58 dhcppc1 kernel: usbcore: registered new interface driver tv8532
Sep 30 12:56:58 dhcppc1 kernel: tv8532: registered
Sep 30 12:58:42 dhcppc1 kernel: usb 5-2: USB disconnect, address 21
Sep 30 12:58:42 dhcppc1 kernel: gspca: disconnect complete
Die TV-Karte ist eine PCI-Karte und die Webcam eine USB :?misiu schrieb:Kann sein, dass die sich mit der TV-Karte ins Gehege kommen.
habe ich aktualisieren lassen.misiu schrieb:Schau noch, ob die "libv4l" die neueste ist
unter diesem Linkmisiu schrieb:und probiere noch die anderen Tipps von da:
http://www.linupedia.org/opensuse/USB_-_Webcam_und_Opensuse_(Einrichten)
List of Logitech non-UVC camera devices
PID ASIC Product name Driver Notes/Reports
0840 ST600 Logitech QuickCam Express qc-usb
Dexxa Webcam qc-usb
0850 ST610 Logitech QuickCam Web qc-usb
0870 ST602 Logitech QuickCam Express qc-usb
Logitech QuickCam for Notebooks
Labtec WebCam
Beim ansehen der beschriebenen Datei "qc-driver.c" findet sich aber der Eintrag einige Zeilen weiter unten.Subject: Re: Logitech Quickcam Express
From: Rafael
Date: Wed, 2 Feb 2005 23:08:38 +0100
Hallo Liste.
Bei mir hat der Treiber qc-usb-0.6.2 geholfen den man hier
runterladen kann: http://sourceforge.net/projects/qce-ga/
Bevor man kompiliert sollte man die Zeile 813 löschen in der Datei qc-driver.c
urb->timeout = 3*HZ; /* 1 s */
Dann funktioniert auch das kompilieren mit der ./quickcam.sh
Nach der Installation des Moduls funktioniert die Kamera es scheinen mit
diesen Treiber fast alle Webcams von Logitech zu laufen.
Herz-von-Hessen@suse:~/Download/qc-usb-0.6.6> ./quickcam.sh
-=- Logitech QuickCam USB camera driver installer -=-
Hello! I am the (hopefully) easy-to-use, fully automated
qc-usb driver installation script.
At the moment, this is experimental, and if it doesn't work,
don't hesitate to quit this with Ctrl+C and install the
driver manually.
The driver is provided in source code form, so it has to be
compiled. This should happen automatically, but it does mean
that there are some steps required before installation.
You also need to know "root" user password to test and
install the driver.
Basically you need only to keep hitting Enter whenever you
see this prompt: --->. Sometimes you're asked root password.
Pay special attention to lines beginning with [!].
It means that some trouble has been detected.
To most important location is the path to your kernel source
or headers. This can be guessed, but you can specify it by
giving it as an argument to this script like this:
./quickcam.sh LINUX_DIR=/usr/src/linux
If you haven't done it yet, now it would be a good moment to
take a look at file README.
Next I'm going to check if you have some important programs installed
and if they and the kernel are of suitable version.
Press Ctrl+C to quit, Enter to continue --->
/home/Herz-von-Hessen/Download/qc-usb-0.6.6/quickcam.sh
/usr/bin/whoami
/bin/su
/bin/ls
/bin/cat
/usr/bin/gcc
/usr/bin/gcc
/usr/bin/make
/usr/bin/grep
/usr/bin/egrep
/usr/bin/awk
/usr/bin/sed
/usr/bin/tail
/usr/bin/head
/usr/bin/install
/usr/bin/ld
/bin/uname
/usr/bin/tr
/usr/bin/xawtv
/usr/bin/xdpyinfo
/bin/dmesg
/usr/bin/wc
which: no realpath in (/home/Herz-von-Hessen/bin:/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/X11R6/bin:/usr/games:/opt/kde3/bin:/usr/lib/mit/bin:/usr/lib/mit/sbin:/opt/gnome/bin:/opt/real/RealPlayer)
which: no realpath in (/usr/local/bin)
/usr/bin/readlink
gcc version: Configured with: ../configure --prefix=/usr --infodir=/usr/share/info --mandir=/usr/share/man --libdir=/usr/lib64 --libexecdir=/usr/lib64 --enable-languages=c,c++,objc,fortran,obj-c++,java,ada --enable-checking=release --with-gxx-include-dir=/usr/include/c++/4.3 --enable-ssp --disable-libssp --with-bugurl=http://bugs.opensuse.org/ --with-pkgversion='SUSE Linux' --disable-libgcj --disable-libmudflap --with-slibdir=/lib64 --with-system-zlib --enable-__cxa_atexit --enable-libstdcxx-allocator=new --disable-libstdcxx-pch --enable-version-specific-runtime-libs --program-suffix=-4.3 --enable-linux-futex --without-system-libunwind --with-cpu=generic --build=x86_64-suse-linux
gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux)
gcc version: Configured with: ../configure --prefix=/usr --infodir=/usr/share/info --mandir=/usr/share/man --libdir=/usr/lib64 --libexecdir=/usr/lib64 --enable-languages=c,c++,objc,fortran,obj-c++,java,ada --enable-checking=release --with-gxx-include-dir=/usr/include/c++/4.3 --enable-ssp --disable-libssp --with-bugurl=http://bugs.opensuse.org/ --with-pkgversion='SUSE Linux' --disable-libgcj --disable-libmudflap --with-slibdir=/lib64 --with-system-zlib --enable-__cxa_atexit --enable-libstdcxx-allocator=new --disable-libstdcxx-pch --enable-version-specific-runtime-libs --program-suffix=-4.3 --enable-linux-futex --without-system-libunwind --with-cpu=generic --build=x86_64-suse-linux
gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux)
Make version: GNU Make 3.81
Linker version: GNU ld (GNU Binutils; openSUSE 11.1) 2.19
Kernel compiler: gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux)
[!]Kernel compiler and gcc seem to be different versions.
Instead, they should be the same. If you have many compilers
installed, you can specify the correct one with command (in bash)
export CC=kgcc
before trying to install the driver. Replace kgcc with the command
required for compiling kernels (kgcc is often used in Red Hat systems).
WARNING: If you press Enter, I'll try to continue anyway,
but this probably will fail. You SHOULD press Ctrl+C now.
Press Ctrl+C to quit, Enter to continue --->
habe ich aktualisieren lassen.misiu schrieb:Schau noch, ob die "libv4l" die neueste ist
Fehler
Paket/tmp/libv4l-0.6.1-1.x86_64-1.rpm kann nicht installiert werden.
Details:
Subprocess failed. Error: RPM fehlgeschlagen: warning:/tmp/libv4l-0.6.1-1.1.x86_64-1.rpm: Header V3 DSA signature: NOKEY, key ID 8004ab64
error: failed dependies:
libv4l = 0.5.9-10.pm.12.1 is needed by (installed) libv4-devel-0.5.9-10.pm.12.1.x86_64
rpm -qa | grep libv4l
libv4l-devel-0.6.1-1.1
libv4l-0.6.1-1.1
Ja richtig, genau das was ich brauchemisiu schrieb:x86_64 : ist für ein 64-Bit Betriebsystem