Hollaender
Member
Hallo,
Ich habe folgendes: SuSe 10, Medion MD 5345, letzte SANE von Packman.
Ich habe Probleme mit dem Scanner und weiss nicht wie ich weiter machen muss:
YAST, Hardware, Scanner, Medion MD 5345: "aktivierung von Genesys ist nicht gelungen"
/home/derk # scanimage -d genesys -T
scanimage: scanning image of size 2549x3500 pixels at 8 bits/pixel
scanimage: acquiring gray frame, 8 bits/sample
scanimage: reading one scanline, 2549 bytes... PASS
scanimage: reading one byte... PASS
scanimage: stepped read, 2 bytes... PASS
scanimage: stepped read, 4 bytes... PASS
scanimage: stepped read, 8 bytes... PASS
scanimage: stepped read, 16 bytes... PASS
scanimage: stepped read, 32 bytes... PASS
scanimage: stepped read, 64 bytes... PASS
scanimage: stepped read, 128 bytes... PASS
scanimage: stepped read, 256 bytes... PASS
scanimage: stepped read, 512 bytes... PASS
scanimage: stepped read, 1024 bytes... PASS
scanimage: stepped read, 2048 bytes... PASS
scanimage: stepped read, 4096 bytes... PASS
scanimage: stepped read, 4095 bytes... PASS
scanimage: stepped read, 2047 bytes... PASS
scanimage: stepped read, 1023 bytes... PASS
scanimage: stepped read, 511 bytes... PASS
scanimage: stepped read, 255 bytes... PASS
scanimage: stepped read, 127 bytes... PASS
scanimage: stepped read, 63 bytes... PASS
scanimage: stepped read, 31 bytes... PASS
scanimage: stepped read, 15 bytes... PASS
scanimage: stepped read, 7 bytes... PASS
scanimage: stepped read, 3 bytes... PASS
Laut SANE sollte das doch machbar sein:
genesys 1.0-8 Medion/Lifetec/Tevion/Cytron MD5345 USB good Has a Primax USB ID sane-genesys
sane-find-scanner :
found SB scanner (vendor=0x0461, product=0x0377, chip=GL646?) at libusb:001:003
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
sane-config --version 1.0.17
Diese dateien von der Sane-genesys seite befinden sich anderswo als ich erwartete: so fand ich genesys.conf in /etc/sane.d
Man Page:
FILES
/usr/local/etc/sane.d/genesys.conf
The backend configuration file (see also description of
SANE_CONFIG_DIR below).
/usr/local/lib/sane/libsane-genesys.a
The static library implementing this backend.
/usr/local/lib/sane/libsane-genesys.so
The shared library implementing this backend (present on systems
that support dynamic loading).
In dll.conf finde ich "genesys" nirgendwo, aber in /etc/sane.d/dll.conf.rpmnew: sehe ich "genesys" stehen :
# enable the next line if you want to allow access through the network:
net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
#canon_pp
coolscan
coolscan2
#dc25
#dc210
#dc240
dmc
epson
fujitsu
#gphoto2
genesys
etc.
# genesys.conf: Configuration file for Genesys Logic GL646 and GL841 based scanners
#
# scanners that are not yet supported
# uncomment them only for developpment purpose
#
# UMAX Astra 4500 and Avision iVina 1600
#usb 0x0638 0x0a10
# Hewlett Packard ScanJet 2400c
#usb 0x03f0 0x0a01
# Hewlett Packard ScanJet 3670c
#usb 0x03f0 0x1405
# Plustek OpticPro ST24
#usb 0x07b3 0x0601
#
# supported scanners
#
# Medion MD5345/MD6228/MD6471
usb 0x0461 0x0377
# Hewlett Packard ScanJet 2300c
usb 0x03f0 0x0901
# Canon LiDE 35/40/50
usb 0x04a9 0x2213
# Canon LiDE 60
usb 0x04a9 0x221c
Wie soll ich weiter machen?
Vielen Dank im Voraus!
mfG, Derk
Ich habe folgendes: SuSe 10, Medion MD 5345, letzte SANE von Packman.
Ich habe Probleme mit dem Scanner und weiss nicht wie ich weiter machen muss:
YAST, Hardware, Scanner, Medion MD 5345: "aktivierung von Genesys ist nicht gelungen"
/home/derk # scanimage -d genesys -T
scanimage: scanning image of size 2549x3500 pixels at 8 bits/pixel
scanimage: acquiring gray frame, 8 bits/sample
scanimage: reading one scanline, 2549 bytes... PASS
scanimage: reading one byte... PASS
scanimage: stepped read, 2 bytes... PASS
scanimage: stepped read, 4 bytes... PASS
scanimage: stepped read, 8 bytes... PASS
scanimage: stepped read, 16 bytes... PASS
scanimage: stepped read, 32 bytes... PASS
scanimage: stepped read, 64 bytes... PASS
scanimage: stepped read, 128 bytes... PASS
scanimage: stepped read, 256 bytes... PASS
scanimage: stepped read, 512 bytes... PASS
scanimage: stepped read, 1024 bytes... PASS
scanimage: stepped read, 2048 bytes... PASS
scanimage: stepped read, 4096 bytes... PASS
scanimage: stepped read, 4095 bytes... PASS
scanimage: stepped read, 2047 bytes... PASS
scanimage: stepped read, 1023 bytes... PASS
scanimage: stepped read, 511 bytes... PASS
scanimage: stepped read, 255 bytes... PASS
scanimage: stepped read, 127 bytes... PASS
scanimage: stepped read, 63 bytes... PASS
scanimage: stepped read, 31 bytes... PASS
scanimage: stepped read, 15 bytes... PASS
scanimage: stepped read, 7 bytes... PASS
scanimage: stepped read, 3 bytes... PASS
Laut SANE sollte das doch machbar sein:
genesys 1.0-8 Medion/Lifetec/Tevion/Cytron MD5345 USB good Has a Primax USB ID sane-genesys
sane-find-scanner :
found SB scanner (vendor=0x0461, product=0x0377, chip=GL646?) at libusb:001:003
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
sane-config --version 1.0.17
Diese dateien von der Sane-genesys seite befinden sich anderswo als ich erwartete: so fand ich genesys.conf in /etc/sane.d
Man Page:
FILES
/usr/local/etc/sane.d/genesys.conf
The backend configuration file (see also description of
SANE_CONFIG_DIR below).
/usr/local/lib/sane/libsane-genesys.a
The static library implementing this backend.
/usr/local/lib/sane/libsane-genesys.so
The shared library implementing this backend (present on systems
that support dynamic loading).
In dll.conf finde ich "genesys" nirgendwo, aber in /etc/sane.d/dll.conf.rpmnew: sehe ich "genesys" stehen :
# enable the next line if you want to allow access through the network:
net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
#canon_pp
coolscan
coolscan2
#dc25
#dc210
#dc240
dmc
epson
fujitsu
#gphoto2
genesys
etc.
# genesys.conf: Configuration file for Genesys Logic GL646 and GL841 based scanners
#
# scanners that are not yet supported
# uncomment them only for developpment purpose
#
# UMAX Astra 4500 and Avision iVina 1600
#usb 0x0638 0x0a10
# Hewlett Packard ScanJet 2400c
#usb 0x03f0 0x0a01
# Hewlett Packard ScanJet 3670c
#usb 0x03f0 0x1405
# Plustek OpticPro ST24
#usb 0x07b3 0x0601
#
# supported scanners
#
# Medion MD5345/MD6228/MD6471
usb 0x0461 0x0377
# Hewlett Packard ScanJet 2300c
usb 0x03f0 0x0901
# Canon LiDE 35/40/50
usb 0x04a9 0x2213
# Canon LiDE 60
usb 0x04a9 0x221c
Wie soll ich weiter machen?
Vielen Dank im Voraus!
mfG, Derk