Solo Jonas
Newbie
Hallo zusammen,
hat jemand ne Ahnung von Thinstation und der zugehörigen
Build - Routine TS-O-Matic (http://thinstation.org/) ????
Ich müh mich jetzt schon seit Tagen damit ab und krieg's nicht
gescheit zum laufen .
Ich würde gerne eine Minimal - Konfiguration für meinen uralt
Laptop machen, um dann per VNCViewer meinen Win2000 -
Rechner fernzusteuern .
Der Laptop ist ein 1996'er Dell Latitude XPi (P90ST) mit 90 MHrz,
12 mB RAM, ner Cirrus Logic SVGA Graphikkarte mit 800x600 und
16 Bit High Color .
Verbunden mit dem Win2000-Rechner ist er über ne Dockingstation
mit ner EthernetKarte die mir als Dell Ethernet Advanced Port Replicator (91C94) angezeigt wird .
Ich hab nen bischen rumgegoogelt und gelesen das diese wohl
SMC 9000-9200 kompatibel ist, was die Treiber angeht .
Ich post euch hier mal meine build.conf und meine thinstation.conf.buildtime :
################################################
### --- Thinstation Build Config --- ###
################################################
#
# This is Thinstation's basic setup file. In this file you decide which
# hardware, programs and features to be included in the Thinstation boot image
# generated by running "./build".
#
# You can customize/limit the possibilities in the thinstation.conf files later.
#
# Anything after a "#" is a comment. You activate "things" by removing the #
# and remove "things" by putting a # in front of them.
#
# First we define which modules to include. Modules are hardware drivers.
# NEVER include more than necessary - the more modules the longer boot time
################################################
### --- Modules to include in boot image --- ###
################################################
# --- Bus Modules
module agpgart # AGP bus module for use with AGP video cards
module pcmcia # PCMCIA Cards
module apm # Advanced power management
# --- PCMCIA/CardBus bridges
# Only include what you really need!
#module yenta_socket # CardBus card and (Yenta) bridge support (Very common)
#module i82365 # Intel i82365 compatible ISA-bus bridge support
#module tcic # Databook TCIC host bridge support (old systems)
# --- Network cards modules
# Have as few as possible
# --- Ethernet 10-100 Mbit Modules
#module 3c501 # 3c501 "EtherLink" support
#module 3c503 # 3c503 "EtherLink II" support
#module 3c505 # 3c505 "EtherLink Plus" support
#module 3c507 # 3c507 "EtherLink 16" support
#module 3c509 # 3c509/3c529 (MCA)/3c579 "EtherLink III" support
#module 3c515 # 3c515 ISA "Fast EtherLink"
#module 3c59x # 3c590/3c900 series (592/595/597) "Vortex/Boomerang" support
#module 8139too # RealTek RTL-8139 PCI Fast Ethernet Adapter support
# # VERY common in no-name network cards. Covers also 8129
#module 8139cp # RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support
#module ac3200 # Ansel Communications EISA 3200 support
#module amd8111e # AMD 8111 (new PCI lance) support
#module at1700 # AT1700/1720 support
#module b44 # Broadcom 4400 ethernet support
#module cs89x0 # CS89x0 support
#module de4x5 # Generic DECchip & DIGITAL EtherWORKS PCI/EISA
#module depca # DEPCA, DE10x, DE200, DE201, DE202, DE422 support
#module dgrs # Digi Intl. RightSwitch SE-X support
#module dmfe # Davicom DM910x/DM980x support
#module hp100 # HP 10/100VG PCLAN (ISA, EISA, PCI) support
#module e100 # EtherExpressPro/100 support (e100, Alternate Intel driver)
#module e2100 # Cabletron E21xx support
#module eepro # EtherExpressPro support/EtherExpress 10 (i82595) support
#module eepro100 # EtherExpressPro/100 support (eepro100, original Becker driver)
#module eexpress # EtherExpress 16 support
module epic100 # SMC EtherPower II
#module eth16i # ICL EtherTeam 16i/32 support
#module ewrk3 # EtherWORKS 3 (DE203, DE204, DE205) support
#module fealnx # Myson MTD-8xx PCI Ethernet support
#module forcedeth # nForce Ethernet support
#module hp-plus # HP PCLAN+ (27247B and 27252A) support
#module hp # HP PCLAN (27245 and other 27xxx series) support
#module lp486e # LP486E on board Ethernet
#module lance # AMD LANCE and PCnet (AT1500 and NE2100) support
#module ne io=0x300 # NE2000/NE1000 support
#module ne2k-pci # PCI version of NE-2000
#module natsemi # National Semiconductor DP8381x series PCI Ethernet support
#module ni5010 # Racal-Interlan (Micom) NI cards
#module ni52 # Racal-Interlan (Micom) NI cards
#module ni65 # Racal-Interlan (Micom) NI cards
#module pcnet32 # AMD PCnet32 PCI support
#module sis900 # SiS 900/7016 PCI Fast Ethernet Adapter support
# # Common in integrated motherboards
module smc-ultra # SMC Ultra support
module smc9194 # SMC 9194 support
#module starfire # Adaptec Starfire/DuraLAN support
#module sundance # Sundance Alta support
#module tlan # TI ThunderLAN support, Compaq Neteligent 10/100
#module typhoon # 3cr990 series "Typhoon" support
#module tulip # DECchip Tulip (dc21x4x) PCI support
#module via-rhine # VIA Rhine support (both Rhine I and II). Common in integrated motherboards
#module wd # WD80*3 support
#module winbond-840 # Winbond W89c840 Ethernet support
# --- Ethernet 1000 Mbit Modules
#module acenic # Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support
#module dl2k # D-Link DL2000-based Gigabit Ethernet support
#module e1000 # Intel(R) PRO/1000 Gigabit Ethernet support
#module ns83820 # National Semiconductor DP83820 support
#module hamachi # Packet Engines Hamachi GNIC-II support
#module yellowfin # Packet Engines Yellowfin Gigabit-NIC support
#module r8169 # Realtek 8169 Gigabit Ethernet support
#module sk98lin # Marvell Yukon Chipset / SysKonnect SK-98xx Support
#module tg3 # Broadcom Tigon3 support
# --- Token Ring modules
#module 3c359 # 3Com 3C359 Token Link Velocity XL adapter support
#module abyss # Madge Smart 16/4 PCI Mk2 support
#module ibmtr # IBM Tropic chipset based adapter support
#module lanstreamer # IBM Lanstreamer chipset PCI adapter support
#module olympic # IBM Olympic chipset PCI adapter support
#module smctr # SMC ISA/MCA adapter support
#module tmsisa # Generic TMS380 ISA support
#module tmspci # Generic TMS380 PCI support
#module mtok # Madge Token Ring Linux Driver
# --- PCMCIA Network Modules
#module 3c574_cs # 3Com 3c574 PCMCIA support
#module 3c589_cs # 3Com 3c589 PCMCIA support
#module pcnet_cs # NE2000 compatible PCMCIA support
#module smc91c92_cs # SMC 91Cxx PCMCIA support
#module xircom_cb # Xircom CardBus supportupport
# --- Wireless Modules
#module orinoco_pci # Prism 2.5 PCI 802.11b adaptor support (EXPERIMENTAL)
#module orinoco_cs # Hermes PCMCIA card support
#module airo_cs # Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards
# --- Modem Modules
#module acm # USB Modem support (CDC ACM)
# -- USB Palm Devices
#module visor # USB Handspring Visor / Palm m50x / Sony Clie Driver
# -- Sound Modules
#module ad1816 # AD1816(A) based cards
# # ad1816=<io>,<irq>,<dma>,<dma2>
#module ad1848 # Microsoft Sound System support
# # ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]
#module cs4232 # Crystal CS4232 based (PnP) cards
#module cs4281 # Crystal Sound CS4281
#module cs46xx # Crystal SoundFusion
#module emu10k1 # Creative SBLive! (EMU10K1)
#module es1371 # Creative Ensoniq AudioPCI 97
#module es1370 # Ensoniq AudioPCI
#module esssolo1 # ESS Technology Solo1
#module gus # Gravis Ultrasound support
# # gus=<io>,<irq>,<dma>,<dma2>
#module i810_audio # Intel ICH (i8xx), SiS 7012, NVidia
# # nForce Audio or AMD 768/811x
#module mad16 # OPTi MAD16 and/or Mozart based cards
# # mad16=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
#module maestro # ESS Maestro, Maestro2, Maestro2E driver
#module maestro3 # ESS Maestro3/Allegro driver
#module nm256_audio # NM256AV/NM256ZX audio support
#module pas2 # ProAudioSpectrum 16 support
# # pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
#module pss # PSS (AD1848, ADSP-2115, ESC614) support
# # pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>
#module sb io=0x220 irq=5 dma=1 dma16=5 # 100% Sound Blaster compatibles
#module sb isapnp=1 # 100% Sound Blaster compatibles
#module sgalaxy # Aztech Sound Galaxy (non-PnP) cards
# # sgalaxy=<io>,<irq>,<dma>,<dma2>,<sgbase>
#module sonicvibes # S3 SonicVibes
#module sscape # Ensoniq SoundScape support
# # sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>
#module trident # Trident 4DWave DX/NX, SiS 7018 or
# # ALi 5451 PCI Audio Core
#module trix # MediaTrix AudioTrix Pro support
#module via82cxxx_audio # VIA 82C686 Audio Codec
#module ymfpci # Yamaha YMF7xx PCI audio (native mode)
# -- USB Devices
#module usb-hid # Needed for USB keyboards and mice
#module usb-storage # Needed for USB-Sticks
#module usb-printer # Needed for USB-Printers
# -- Storage Devices
module ide-floppy # LS-120, Iomega Zip
module floppy # Floppy Disk Drive Support
#module cdrom # CD-Rom Drive Support
# -- Filesystem Support
# -- Every mounted device needs a filesystem, choose which ones are supported below.
module isofs # ISO9960 file system support for CDRoms
module vfat # Fat and VFat file system support
#module ext2 # Ext2 file system support
#module ext3 # Ext3 file system support
#module supermount # Supermount support for auto unmounting of removable media
#module nfs # NFS file system support
#module smbfs # Samba client FS Support, allows you to mount smb filesystems
#################################################
### --- Packages to include in boot image --- ###
#################################################
# A package is a program or utility.
# Any packages may be added as "package" or "pkg".
# If defined as a "package" the program is included in the boot image.
# If defined as a "pkg" the program is added from outside the image.
# Normally use "package", and only "pkg" if the image approaches 16 MB or
# you know what you are doing.
# --- Packages to include in boot image
# --- Packages below may be "package" or "pkg"
#package hwclock # Utility to set system time from hardware clock
#package sound-esd # Enable one of these modules if you want to be able to control
#package sound-nasd # sound on your thinstation from another computer or
# your remote session.
# --- X related packages
#package xorg6-tinyx # TinyX Xvesa server (for low memory machines)
# works with ICA too, is slower, don't choose any X modules with
# this server, you don't need anything else.
# Otherwise choose from Xfree 3 or 4 (4 is recommended)
package xf3-svga # XF86_SVGA 3.3.6 server
#package xf3-s3 # XF86_S3 3.3.6 server
#package xf3-vmware # VMWare X server for development
#package xorg6vnc # Xorg VNC Server Module. With this package you can
# connect to the TS client's desktop from a java
# browser on "http://<TS ip>:5800
# --- Xorg6R7.0
# General Xorg6R7.0 video drivers:
# Only include what you really need!
#package xorg6-apm # Alliance ProMotion video driver
#package xorg6-ark # Ark Logic video driver
#package xorg6-ati # ATI video driver
#package xorg6-chips # Chips and Technologies video driver
package xorg6-cirrus # Cirrus Logic video driver
#package xorg6-cyrix # Cyrix video driver
#package xorg6-glint # GLINT/Permedia video driver
#package xorg6-i128 # Number 9 I128 video driver
#package xorg6-i740 # Intel i740 video driver
package xorg6-i810 # Intel 8xx integrated graphics chipsets
#package xorg6-mga # Matrox video driver
#package xorg6-neomagic # Neomagic video driver
#package xorg6-nsc # Nsc video driver
#package xorg6-nv # NVIDIA video driver
#package xorg6-r128 # ATI Rage 128 video driver
#package xorg6-radeon # ATI RADEON video driver
#package xorg6-rendition # Rendition video driver
#package xorg6-s3 # S3 video driver
#package xorg6-s3virge # S3 ViRGE video driver
#package xorg6-savage # S3 Savage video driver
#package xorg6-siliconmotion # Silicon Motion video driver
#package xorg6-sis # SiS video driver
#package xorg6-tdfx # 3Dfx video driver
#package xorg6-tga # DEC TGA video driver
#package xorg6-trident # Trident video driver
#package xorg6-tseng # Tseng Labs video driver
package xorg6-vesa # Generic VESA driver, use this if you don't know what to use
#package xorg6-vga # VGA 320x200 8 bit
#package xorg6-via # VIA video driver
#package xorg6-vmware # VMware SVGA video driver
# --- Keyboard layouts (Language/Country)
#package keymaps-ar # Arabic
#package keymaps-cs # Czech
#package keymaps-da # Danish
package keymaps-de # German
#package keymaps-de_ch # German-Switzerland
#package keymaps-en_gb # English-Great Britian
#package keymaps-en_in # English-United States International
#package keymaps-en_nz # English-New Zealand
package keymaps-en_us # English-United States
#package keymaps-es # Spanish
#package keymaps-et # Estonian
#package keymaps-fr_be # French-Belgium
#package keymaps-fr_ca # French-Canada
#package keymaps-fr_ch # French-Switzerland
#package keymaps-fr # French
#package keymaps-hr # Croatian
#package keymaps-hu # Hungarian
#package keymaps-it # Italian
#package keymaps-ja # Japanese
#package keymaps-la # Latin
#package keymaps-lt # Lithuanian
#package keymaps-lv # Latvian
#package keymaps-mk # Macedonian
#package keymaps-nl # Dutch
#package keymaps-no # Norwegian
#package keymaps-pl # Polish
#package keymaps-pt_br # Portuguise-Brazil
#package keymaps-pt # Portuguise
#package keymaps-ro # Romanian
#package keymaps-ru # Russian
#package keymaps-sv_fi # Swedish-Finland
#package keymaps-sv # Swedish
#package keymaps-sl # Slovenian
#package keymaps-th # Thai
#package keymaps-tr # Turkish
# --- Connection Package types
# Choose *at least* one!
#package rdesktop # X RDP client for Windows Terminal Services (ver 1.3.1)
#package rdesktop_svga # SVGA RDP client, This is Version 1.1 of rdesktop Only
# Use this for low memory machines
package vncviewer # VNC client (vncviewer)
#package ica # Citrix ICA client support
#package tarantella # Tarantella client support
#package ica_wfc # Citrix ICA manager
#package xnest # XDM in a window client
#package rxvt # Light Xterm Client (vt102)
#package xterm # Xterm Client (vt220)
#package ssh # Secure Shell client
#package tn5250 # 5250 terminal emulator
#package dillo # Dillo light web browser
#package nx # No Machine NX client
# --- Window Managers
# Choose no more than 1 window manager
# Not needed if you don't want to manage windows
package blackbox # "Blackbox" window manager. Makes TS a light workstation.
#package icewm # "ICEWM" window manager. Makes TS a light workstation.
# Is a little bigger than blackbox
# --- Window Manager Utils
#package xtdesk # Adds icons to desktop
# --- Other services
package www # Web access to client. From a browser: "http://<IP number>"
# The standard page is for general user settings, administrative access
# is on port 6800
#package lp_server # Remote printing daemon (LaserJet compatible)
#package lpr # LPR Print Server, for use with samba-server package
#package tftpd # TFTP, built in tftpd server
# Useful for making a tftpserver for thinstation on a WAN
# over a slow link
#package samba-server # Samba server FS Support, allows you to share
# local floppy/cdrom/hd/printer to other Windows
# PCs; Needs supermount for removeable media
# --- Miscellaneous
#package e3 # Basic vi like Editor
#package debug # Debug support, adds strace and other commands
# not recommended for normal use.
########################################
### --- Miscellaneous Parameters --- ###
########################################
param rootpasswd klar, setz ich noch ein # Do Change! Console/telnet password for Root
# If this is enabled, Telnetd will be enabled
param xorgvncpasswd klar, setz ich noch ein # VNC Access Password
#param storagepasswd pleasechangeme # Password for storage server
#param dialuppasswd pleasechangeme # Password for dialin account
#param sambapasswd pleasechangeme # Password for samba shares when using user mode security
param bootlogo false # Want a backgound picture during boot
param bootresolution 800x600
param defaultconfig thinstation.conf.buildtime # The file with default setup
# no other config file is found
# during boot
param basename thinstation # used for all config/tftp file names
param basepath . # used to determine path to tftp files
param localpkgs false # to determine is PKG files are to be loaded locally
param fulllocales false # Use full locale support for packages
param icaencryption false # Use ica encryption support, add 290k to image
param bootvebosity 3 # Increased vebosity when booting TS
# 0 no verbose messages
# 1 boot
# 2 network
# 4 init
# 8 kernel
# 16 modules
# 32 packages
# 64 email bootlog file to SMTP server & user set in
# thinstation.conf file. This will only work
# if networking is working.
#
# Combinations can be used, ie 12 does Kernel and Module Messages
#package emelfm
#package evilwm
#package links #Links web browser supporting HTML 4, SSL and Javascript
#package lprng # LPRng
#package mplayer # MPlayer - The Movie Player (www.mplayerhq.hu)
#package sylpheed # Sylpheed-claws E-mail client
#package xcalc # The X pocket calculator, TI or HP style
#package xpdf # Xpdf - http://www.foolabs.com/xpdf - PDF reader
#package firefox # Firefox web browser
#package flash # Flash, you must have also downloaded the firefox package
#package cdparanoia # "rips" cd audio tracks, converting them to audio files
#package libao # required audio library for playback
#package mpg321 # play and decode mp3 audio
#package vorbis-tools # encoding, decoding and playback for ogg format
#package sox # multi-format sound (mp3, wav, ogg, etc.) translator/player
#package xmms # winamp like mp3-player
#################################################
# --- Thinstation sample configuration file --- #
#################################################
#
# This file must be named "thinstation.conf<xxx>" where <xxx> can be:
# .buildtime Defines the defaults build into the image (note the leading .)
# .network Default config file loaded from the TFTP server.
# .user Config file on local storage.
# -<name> Specific config file on the TFTP server for the terminal
# "name" (e.g. thinstation.conf-paul). Requires thinstation.hosts.
# .group-<id> Config file for a group of terminals (e.g. with printer setup
# for those terminal with local printers. Requires thinstation.hosts.
# -<IP> Specific config file on the TFTP server for the terminal with
# the IP number <IP> specified.
# -<MAC> Specific config file on the TFTP server for the terminal with
# the MAC address specified.
# --- General Options
#
# AUDIO_LEVEL Audio Level for sound, 0-100
# KEYBOARD_MAP Keyboard layout
# TIME_ZONE Used to set time zone on TS client by entering the UTC offset.
# This can be set automatically if the appropriate dhcpc option is selected
# (Option 2, time offset in seconds)
# SYSLOG_SERVER Log server ip address or hostname.
# If the work "local" is used, then syslog starts logging locally
# If not specified syslogd is not loaded.
# USB_ENABLED Enable USB Drivers into memory if USB package is chosen
# DAILY_REBOOT Will reboot server if up over a day and one of the session
# types is closed
# AUTOPLAYCD If enabled this will autoplay music cds when inserted.
# CUSTOM_CONFIG Allows choosing custom boot config, On/Off
# RECONNECT_PROMPT This displays the reconnection/shutdown options for when a session is ended
#
# OFF No reconnect prompt
# ON Reconnect prompt will be displayed
# MENU Shows a menu with a shutdown and reconnection option
# MENUXX As MENU option, but the XX is a time period in minutes.
# After XX minutes shutdown will occur unless the reconnect option
# is choosen
AUDIO_LEVEL=0
KEYBOARD_MAP=de
TIME_ZONE="UTC-2:00"
SYSLOG_SERVER=local
USB_ENABLED=Off
DAILY_REBOOT=On
#AUTOPLAYCD=On
CUSTOM_CONFIG=Off
RECONNECT_PROMPT=On
# --- Default Settings for all sessions
#
# SCREEN Display number to run the X server on
# AUTOSTART ON Application will be executed immediately at startup
# OFF Application will appear in a menu to be started manually
# WORKSPACE Workspace in the window manager to run the application in
# ICONMODE MANUAL Default sessions are not created in window manager/desklaunch
# AUTO Default sessions types are created in window manager/desklaunch
SCREEN=0
WORKSPACE=1
AUTOSTART=On
ICONMODE=AUTO
# --- Citrix ICA Specific Options
#
# GLOBAL Settings
#ICA_USE_SERVER_KEYBOARD Use default server keyboard, otherwise use KEYBOARD_MAP
# variable
#ICA_BROWSER_PROTOCOL Broswer protocol, can be HTTPonTCP or UDP
#
# APPLICATION SET settings
#ICA_ENCRYPTION Encryption level for ICA
# Valid Settings Below
# "Basic"
# "RC5 (128 bit - Login Only)"
# "RC5 (40 bit)"
# "RC5 (128 bit)"
# "RC5 (56 bit)"
#ICA_COMPRESS Compression, On/Off
#ICA_AUDIO Audio, On/Off
#ICA_AUDIO_QUALITY Audio Quality, Low, Medium, High
#ICA_PRINTER This will turn on ICA autocreate printers, see printer section
# for details, On/Off
#
# NOTE: You must have the lpr package included for this option
# to work.
#
#ICA_APPLICATION_SET Published Application (Not needed if using
# ICA_SERVER)
#ICA_SERVER Server to Connect to (Not needed if using
# ICA_APPLICATION_SET, but needed if the ICA-Masterbrowser
# is not on the local network.)
#ICA_WFCLIENT_type_specific This allows you to specify specific config file details for global ica
# parameters any parameter can be changed with this setting. An example of this is
# ICA_WFCLIENT_CLIENTDRIVE="On"
# See your application manual for documentation on the settings which
# can be used.
#ICA_USE_SERVER_KEYBOARD=Off
#ICA_BROWSER_PROTOCOL=HTTPonTCP
#ICA_SERVER=
#ICA_ENCRYPTION=Basic
#ICA_COMPRESS=On
#ICA_AUDIO=On
#ICA_AUDIO_QUALITY=Low
#ICA_PRINTER=Off
#ICA_SEAMLESS_WINDOW=Off
# --- Session Options
#
# Note: # is a number equal to or greater than 0
#
# SESSION_#_TITLE Title description for SESSION. Needed for replimenu.
# SESSION_#_TYPE Package type, choose beetwen:
# - vncviewer Start vncviewer in X
# - rdesktop Start rdesktop in X
# - rdesktop_svga Start svga rdesktop, based on rdesktop 1.1 code
# for low memory machines
# - x Start x-terminal session (xdm)
# - xnest Start x-terminal session (xdm) from within blackbox
# - ssh Start ssh client in linux console
# - telnet Start telnet client in linux console
# - ica Start Citrix ICA client in X
# - ica_wfc Start ICA Manager
# - blackbox Start blackbox window manager session
# - icewm Start icewm window manager session
# - dillo Start Web Browser in X
# - tftpd Start tftp daemon
# - tarantella Start tarantella client
# - rxvt Start light xterm client
# - xterm Start xterm client
# - tn5250 Start AS400 client in linux console
# - nx Start NX Client Session
# SESSION_#_SCREEN Display number to run the X server on
# SESSION_#_AUTOSTART ON Application will be executed immediately at startup
# OFF Application will appear in a menu to be started manually
# SESSION_#_CUSTOM_CONFIG ON Allows choosing custom config for when session starts
# OFF Session boots normally
# SESSION_#_ICON ON Places Icon on Desktop if package Desklaunch is selected and
# in Window Manager Main Menu
# SUBMENU Places Icon on Desktop if package Desklaunch is selected and
# in a Submenu within the window manager
# SESSION_#_WORKSPACE Workspace to run program on in a window manager
# SESSION_#_type_SERVER IP address/hostname of the server
# SESSION_#_type_OPTIONS Command line options for the session type
#
# SESSION_#_type_specific This allows you to specify specific config file details for certain session
# types. Currently support is NX and ICA. Any configuration file setting
# can be changed with this setting. An example of this is
# SESSION_0_NX_GENERAL_DESKTOP="Gnome"
# SESSION_0_ICA_APPSRV_USEFULLSCREEN="Yes"
# See your application manual for documentation on the settings which
# can be used.
# Individual Session Settings, override defaults
#
# IMPORTANT: Make sure you minimum have a SESSION_0. Otherwise you will get an error
# on boot. You may have additional sessions: SESSION_1, SESSION_2 ...
# SESSION_0 is on ctrl-alt-F3
# SESSION_1 is on ctrl-alt-F4
# ... etc.
SESSION_0_TYPE=blackbox
#SESSION_1_TYPE=ica
#SESSION_1_ICA_APPLICATION_SET="Microsoft Word"
#SESSION_1_ICA_OPTIONS="-username donald -clearpassword qwak -domain disney"
#SESSION_1_ICON=ON
#SESSION_2_TYPE=ica
#SESSION_2_ICA_SERVER=ICA
#SESSION_3_TYPE=ica_wfc
# The -a option here specifies the color depth
# Note certain servers support certain color depths, wrong settings with this
# May cause your connection to fail.
#SESSION_4_TITLE="Big Bad Server Donald"
#SESSION_4_TYPE=rdesktop
#SESSION_4_SCREEN=1
#SESSION_4_SCREEN_POSITION=2
#SESSION_4_RDESKTOP_SERVER=192.168.1.1
#SESSION_4_RDESKTOP_OPTIONS="-u user -p password -a 16"
#SESSION_4_AUTOSTART=Off
#SESSION_#_TITLE="Big Bad Server Road Runner"
#SESSION_#_TYPE=rdesktop
#SESSION_#_SCREEN=1
#SESSION_#_RDESKTOP_SERVER=192.168.1.1
#SESSION_#_RDESKTOP_OPTIONS="-u 'fred' -a 8"
#SESSION_#_AUTOSTART=Off
#SESSION_#_TYPE=rxvt
#SESSION_#_SCREEN=1
#SESSION_#_RXVT_OPTIONS="-bg black -cr green -fg white -C -sl 500"
#SESSION_#_WORKSPACE=2
#SESSION_#_TYPE=blackbox
#SESSION_#_SCREEN=1
SESSION_1_TYPE=x
#SESSION_#_SCREEN=2
SESSION_1_X_SERVER=192.168.1.2
SESSION_1_X_OPTIONS="-indirect"
#SESSION_#_AUTOSTART=Off
#SESSION_#_TYPE=xnest
#SESSION_#_X_SERVER=192.168.1.3
#SESSION_#_X_OPTIONS="-query"
#SESSION_#_AUTOSTART=On
#SESSION_#_TYPE=telnet
#SESSION_#_TELNET_SERVER=192.168.1.2
#SESSION_#_TYPE=ssh
#SESSION_#_SSH_SERVER=192.168.1.2
SESSION_2_TYPE=vncviewer
SESSION_2_VNCVIEWER_SERVER=192.168.1.2 #zB. kommt hier die
# IP von meinem Win2000 hin ??
#SESSION_#_TYPE=tn5250
#SESSION_#_TN5250_SERVER=192.168.1.2
#SESSION_#_TYPE=nx
#SESSION_#_TITLE="Gnome"
#SESSION_#_NX_ADVANCED_ENABLE_SSL_ENCRYPTION="true"
#SESSION_#_NX_GENERAL_DESKTOP="Gnome"
#SESSION_#_NX_GENERAL_SERVER_HOST="nx-server-ip"
#SESSION_#_NX_GENERAL_REMEMBER_PASSWORD="true"
#SESSION_#_NX_GENERAL_RESOLUTION="fullscreen"
#SESSION_#_NX_GENERAL_SESSION="Unix"
#SESSION_#_TYPE=nx
#SESSION_#_TITLE="Firefox"
#SESSION_#_NX_ADVANCED_ENABLE_SSL_ENCRYPTION="true"
#SESSION_#_NX_GENERAL_DESKTOP="Console"
#SESSION_#_NX_GENERAL_SERVER_HOST="nx-server-ip"
#SESSION_#_NX_GENERAL_REMEMBER_PASSWORD="true"
#SESSION_#_NX_GENERAL_COMMAND_LINE="/usr/local/firefox/firefox"
#SESSION_#_NX_GENERAL_SESSION="Unix"
#SESSION_#_NX_GENERAL_ONLY_CONSOLE="false"
#SESSION_#_TYPE=nx
#SESSION_#_TITLE="Windows"
#SESSION_#_NX_ADVANCED_ENABLE_SSL_ENCRYPTION="true"
#SESSION_#_NX_GENERAL_DESKTOP="RDP"
#SESSION_#_NX_GENERAL_RESOLUTION_VALUE="fullscreen"
#SESSION_#_NX_GENERAL_SERVER_HOST="nx-server-ip"
#SESSION_#_NX_GENERAL_SESSION="Windows"
#SESSION_#_NX_WINDOWS_SESSION_SERVER="windows-server-ip"
#SESSION_#_NX_WINDOWS_SESSION_AUTHENTICATION="1"
#SESSION_#_TYPE=icewm
# --- PKG Options
#
# PKG_PACKAGES Choice of packages to download for PKG
# You can also use PKG_PACKAGES1-8 for additional package selections
# This is useful for using multiple network group files
# PKG_PREFIX Download PKGs from a subdir of /tftpboot or PKG Path if PKG_PATH
# is set in thinstation.conf
# PKG_PATH Path to PKG files if not using tftpboot
# Floppy: /mnt/floppy
# CD-ROM: /mnt/cdrom
# HD: /mnt/disc/disc0/part1 (first disc, first partition)
# MOD_PACKAGES Choice of modules to download for MPKG
# You can also use MOD_PACKAGES1-8 for additional package selections
# This is useful for using multiple network group files
# MOD_PREFIX Downloads and insmod's a module from a subdir of /tftpboot
# if MOD_PREFIX is set in thinstation.conf
#PKG_PACKAGES="blackbox rxvt"
#PKG_PREFIX=pkg
#PKG_PATH=/mnt/cdrom
#MOD_PACKAGES="usb-hid usb-storage"
#MOD_PREFIX=modules
# --- X Server Options
#
# SCREEN_RESOLUTION Screen resolutions available in the workstations
# SCREEN_COLOR_DEPTH Number of bits per pixel (8,16,24)
# SCREEN_HORIZSYNC Monitor horizontal sync frequency in Khz.
# If left blank Xorg will try to detect with DDC
# SCREEN_VERTREFRESH Monitor vertical refresh frecuency in Hz.
# If left blank Xorg will try to detect with DDC
# SCREEN_X_FONT_SERVER IP address or hostname of the font server for X
#
# Screen Saver Settings
# SCREEN_BLANK_TIME Minutes to X session goes blank
# SCREEN_STANDBY_TIME Minutes to X session goes into standby mode
# SCREEN_SUSPEND_TIME Minutes to X session goes into suspend mode
# SCREEN_OFF_TIME Minutes to X session turn off
#
# MOUSE_PROTOCOL Mouse protocol type (Microsoft, PS/2, etc.)
# (mouse is autodetected, use this only if it fails)
# MOUSE_DEVICE Mouse device: /dev/ttyS0 -> COM1
# /dev/ttyS1 -> COM2
# /dev/ttyS2 -> COM3
# /dev/ttyS3 -> COM4
# /dev/psaux -> PS/2 mouse port
# /dev/input/mice -> USB mouse (needs USB package)
# MOUSE_RESOLUTION Mouse resolution
# --- Advanced XServer Options - Experts Only
# X_DRIVER_NAME Driver for X, this will override the autodetection scripts
# X_DRIVER_BUSID Screen Card BusID
# X_DRIVER_OPTION1-4 Addditional options for driver
SCREEN_RESOLUTION="800x600 | 640x480 | *"
SCREEN_COLOR_DEPTH="16 | 8 | *"
#SCREEN_HORIZSYNC="30-64 | *"
#SCREEN_VERTREFRESH="56-87 | 60 | 56 | 70 | 72 | 75"
#SCREEN_X_FONT_SERVER=192.168.1.2:7100
SCREEN_BLANK_TIME=10
SCREEN_STANDBY_TIME=20
SCREEN_SUSPEND_TIME=30
SCREEN_OFF_TIME=60
#MOUSE_PROTOCOL=PS/2
#MOUSE_DEVICE=/dev/psaux
MOUSE_RESOLUTION=100
# --- Advanced Options - Experts Only
#X_DRIVER_NAME="mga"
#X_DRIVER_BUSID="PCI:1:0:0"
X_DRIVER_OPTION1="swcursor On"
#X_DRIVER_OPTION2="ActiveDevice CRT"
#X_DRIVER_OPTION3="noDDC Off"
#X_DRIVER_OPTION4="UseBios Off"
#X_DRIVER_OPTION5="ShadowFB Off"
# --- Printing Options
#
# PRINTER_0_NAME Workstation Printer Name, Can be Any Valid Name
# If you have turned ICA_PRINTER=ON then this is the
# name of the printer driver
# PRINTER_0_DEVICE Workstation printer device (if not specified devices
# are not loaded).
# /dev/printers/[0-2] for parallel ports
# /dev/ttyS[0-3] for serial ports
# /dev/usb/lp[0-2] for USB printers
#
# PRINTER_0_TYPE P for parallel, S for serial, U for USB printer
# PRINTER_0_OPTIONS Serial port options.
# PRINTER_1_* See PRINTER_0_*
# PRINTER_2_* See PRINTER_0_*
# PRINTER_3_* See PRINTER_0_*
#PRINTER_0_NAME="parallel"
#PRINTER_0_DEVICE=/dev/printers/0
#PRINTER_0_TYPE=P
#PRINTER_1_NAME="serial"
#PRINTER_1_DEVICE=/dev/ttyS1
#PRINTER_1_TYPE=S
#PRINTER_1_OPTIONS="speed 38400 -imaxbel"
#PRINTER_2_NAME="usb"
#PRINTER_2_DEVICE=/dev/usb/lp0
#PRINTER_2_TYPE=U
#PRINTER_3_NAME="usb"
#PRINTER_3_DEVICE=/dev/usb/lp0
#PRINTER_3_TYPE=U
#ICA Autocreate Printer Example
#PRINTER_0_NAME="HP LaserJet Series II"
#PRINTER_0_DEVICE=/dev/printers/0
#PRINTER_0_TYPE=P
# --- Permanent Storage Options
#
# STORAGE_PATH Path to where storage device is mounted to save
# profile settings. This should be one of
# /mnt/usbdevice/busX.targetX.lunX/partX or disc
# /mnt/floppy
# /mnt/disc/discX/partX
# /mnt/nfs
# /mnt/smb
#
# Note that the profile settings are stored under
# a subfolder for this path. So the path to the
# stored settings would be something like
# /mnt/floppy/thinstation.profile
# See the FAQ on the website for more details on this
#
# Also checkout README.IMPORTANT for the valid
# config files which you can place here
# a typical file to store config file settings is
# /mnt/floppy/thinstation.profile/thinstation.user
#
# Also note that the .profile can be changed by using
# the below STORAGE_PREFIX
# STORAGE_SERVER This is the path to the SMB or NFS server, ie
# server:/path/to/profile
# STORAGE_USER This is the username for SMB mounts, password is
# defined at build time in build.conf
# STORAGE_PREFIX This is prefex for the folder name to store settings
# in on the storage device. You can also use one of the
# special characters below.
#
# M = Mac Address
# H = Hostname
# I = Ip Address
#
# Note default prefix for storing the profile is
# .profile
# STORAGE_CONFIG1-8 This is the path for any user defined settings
# which will always override the profile path above
# The files are tried on order on each device specified
#STORAGE_PATH=/mnt/nfs
#STORAGE_SERVER=bigserver:/opt/thinstation
#STORAGE_USER=duck
#STORAGE_PREFIX=H
#STORAGE_CONFIG1=/mnt/floppy
#STORAGE_CONFIG2=/mnt/cdrom
#STORAGE_CONFIG3=/mnt/disc/disc1/part1
#STORAGE_CONFIG4=/mnt/usbdevice/busX.targetX.lunX/partX or disc
# --- Samba Options
#
# SAMBA_SERVER_ENABLED Enable Samba Server Daemons, On/Off
# SAMBA_SECURITY Type of security, USER, DOMAIN, SERVER
# SAMBA_SERVER Server for security
# SAMBA_WINS Server Name to Enable Samba to be a WINS Client
# SAMBA_HARDDISK Enable Harddrive support, On/Off
# SAMBA_CDROM Enable CDRom Support, On/Off
# SAMBA_FLOPPY Enable Floppy Support, On/Off
# SAMBA_PRINTER Enable Printer Support, On/Off
# SAMBA_USB Enable USB Support, On/Off
#SAMBA_SERVER_ENABLED=Off
#SAMBA_WORKGROUP=BigPeople
#SAMBA_SECURITY=Server
#SAMBA_SERVER=BadMan
#SAMBA_WINS=BadMan
#SAMBA_HARDDISK=Off
#SAMBA_CDROM=On
#SAMBA_FLOPPY=On
#SAMBA_PRINTER=On
#SAMBA_USB=Off
# --- Networking Options
#
# NET_HOSTNAME Hostname to use if not using a thinstation.hosts file, note
# that the machine MAC address will replace any * if used.
# NET_REMOTE_ACCESS_FROM List of hostnames/ip address accepted by the server
# for remote control, used by telnetd and www packages
# NET_SMTP_SERVER Email server address for error logs
# NET_SMTP_EMAIL Email address of administrator
# NET_TELNETD Enables built-in telnetd server package
#
#NET_HOSTNAME=donald
#NET_HOSTNAME=ts_*
#NET_SMTP_SERVER=donald
#NET_SMTP_EMAIL=donald@duck.org.nz
#NET_TIME_SERVER=mickey
#NET_TELNETD_ENABLED=On
#NET_REMOTE_ACCESS_FROM="duck.quak.org.au 192.168.0.0 .disney.us"
# --- For use in thinstation.conf.buildtime only:
#
# NET_USE_DHCP Enable DHCP Resolution, On/Off
# NET_IP_ADDRESS IP Address of client
# NET_MASK Network mask of client
# NET_GATEWAY IP Address of gateway
# NET_USE_TFTP Use tftp server for config file, On/Off
# NET_DNS1 DNS Server 1
# NET_DNS2 DNS Server 2
# NET_DNS_SEARCH Default DNS domain to search
# NET_ALTERNATE_TFTP Alternate tftp server for vmware or non-standard dhcp servers
#NET_USE_DHCP=Off
#NET_IP_ADDRESS=192.168.0.1
#NET_MASK=255.255.255.0
#NET_GATEWAY=192.168.0.254
#NET_USE_TFTP=Off
#NET_DNS1=192.168.0.2
#NET_DNS2=192.168.0.3
#NET_DNS_SEARCH=cartoons.org.nz
#NET_ALTERNATE_TFTP=192.168.0.4
# --- Wireless support (DHCP only!)
#
#WIRELESS_ESSID # ESSID (extended network name) : My Network, any
#WIRELESS_NWID # NWID/Domain (cell identifier) : 89AB, 100, off
#WIRELESS_MODE # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
#WIRELESS_FREQ # 2.422G, 2.46G (frequency)
#WIRELESS_CHANNEL # 1, 2, 3 (channel)
#WIRELESS_SENS # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
#WIRELESS_RATE # Bit rate : auto, 1M, 11M
#WIRELESS_RTS # RTS threshold : off, 500
#WIRELESS_FRAG # Fragmentation threshold : off, 1000
#WIRELESS_IWCONFIG # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
#WIRELESS_IWSPY # iwspy parameters : + 01:23:45:67:89:AB
#WIRELESS_IWPRIV # iwpriv parameters : set_port 2, set_histo 50 60
#WIRELESS_KEY # Encryption key : 4567-89AB-CD, s
assword
#WIRELESS_ESSID="ssid"
#WIRELESS_NWID=""
#WIRELESS_MODE="managed"
#WIRELESS_FREQ=""
#WIRELESS_CHANNEL=""
#WIRELESS_SENS=""
#WIRELESS_RATE=""
#WIRELESS_RTS=""
#WIRELESS_FRAG=""
#WIRELESS_IWCONFIG=""
#WIRELESS_IWSPY=""
#WIRELESS_IWPRIV=""
#WIRELESS_KEY="abcdef"
# --- HD Update options
#
# HDUPDATE_ENABLED=Y Enable Update
# HDUPDATE_WS_VERSION Version of files on workstation (set in thinstation.buildtime only)
# HDUPDATE_SERVER_VERSION Version of files on server (set in both buildtime and network)
# This should be set in buildtime to match the WS_VERSION to prevent
# unintended upgrades
#
# HDUPDATE_SERVER tftp server name
# HDUPDATE_PATH Path to files /ts/update
# HDUPDATE_FORCE Force install even if not needed
# HDUPDATE_FILES List of files to upgrade
# HDUPDATE_DELETE List of files to delete (no sanity checks, use with caution)
#HDUPDATE_WS_VERSION=1
#HDUPDATE_ENABLED=Y
#HDUPDATE_SERVER_VERSION=CO.29
#HDUPDATE_SERVER=roadrunner
#HDUPDATE_PATH=/ts/update
#HDUPDATE_FORCE=N
# Set the list of files to download
#HDUPDATE_FILES="vmlinuz hires lowres syslinux.cfg thin.txt firefox.pkg flash.pkg"
#HDUPDATE_FILES="hires lowres"
#HDUPDATE_FILES="lowres"
#HDUPDATE_FILES="hires"
#HDUPDATE_FILES="syslinux.cfg thin.txt"
#**** EXPERIMENTAL ****
# Dual Head Support
#
# This allows two seperate X sessions to be started with seperate input devices. This allows
# effectively two seperate machines within the same PC. You will need seperate screen cards
# to enable this. It is best to use with 1 AGP card and 1 PCI card.
# Check out http://www.ltn.lv/~aivils/eng-video.html for a list of known compatable screen cards
# Input Device support should be:
#
# Primary mouse and keyboard PS/2
# Secondary mouse and keyboard USB
#
# There is some basic detection scripts for this, but these will need to be improved in TS 3.0.
# If thinstation doesn't detect both a USB keyboard and mouse it will default back to dual
# screen support, not dual head.
#
# This is not considered stable. If you exit the session, or try to change to a console screen
# with Alt-F1 etc... it will probably crash the machine. If it doesn't work with your hardware
# there is nothing that can be done about it.
# The kernel Advanced Power Management module is disabled when using dual screen as it causes the
# second screen to crash.
# Note the below option only supports 1-2, anything more than two won't work. This is provided
# for future development, to create a machine with more than two seperate sessions.
# SESSION_#_SCREEN_POSITION 1-X When using dual screen support you can specify the position
# of each session. This allows to seperate sessions to be on
# seperate screens. If only 1 session is in use, this option will
# make no differnece. You can specify between 1+ positions
# Sylpheed settings
#SYLPHEED_USENFS=N # store/get settings on NFS. If set to 'N' the
# files are created at package initialization,
# using settings below, which are then placed
# in $HOME/.sylpheed
# If set to 'Y' the user is asked to enter his/her
# account settings at first time startup and the
# settings are stored in $HOME/.sylpheed , which
# is symlinked to /mnt/nfs/$CLIENT_MAC/.sylpheed
#SYLPHEED_ACCOUNTNAME="Account1" # account description
#SYLPHEED_FULLNAME="Joe Sixpack" # full user name
#SYLPHEED_MAILADDRESS="joe@mycompany.com" # email address
#SYLPHEED_ORGANIZATION="Thinstation User" # organization
#SYLPHEED_PROTOCOL=3 # 0 = POP3
# 1 = POP3 w/ APOP
# 2 = ???
# 3 = IMAP4
# 4 = NNTP
# 5 = local mailbox
# 6 = SMTP only
#SYLPHEED_RECEIVESERVER=my.pop3-or-imap4.server # IMAP4/POP3 servername
#SYLPHEED_SMTPSERVER=my.smtp.server # SMTP servername
#SYLPHEED_NNTPSERVER=my.nntp.server # NNTP servername
#SYLPHEED_USERID="joe" # IMAP4/POP3 username
#SYLPHEED_PASSWD=secret # IMAP4/POP3 password - will be encrypted at
# first-time start
#SYLPHEED_PLUGINS="dillo" # specify which plugins should be auto-loaded
# valid options (case sensitive) are:
# - dillo
# - imageviewer
# - trayicon
# separate plugins with a space ("dillo trayicon")
#SYLPHEED_BROWSER="your-browser %s" # define which browser should be used to edit/view
# HTML documents. Note that %s will be substituted
# for the URL/filename
#SYLPHEED_EDITOR="your-editor %s" # define which editor should be used to compose
# new mail messages. Note that %s will be substituted
# for the filename
# Example configuration for MPlayer
#SESSION_0_TITLE="MPlayer"
#SESSION_0_TYPE=mplayer
# Optional variables
# NFS support
#MPLAYER_NFS="server:/path/to/movies"
# SMB support
#MPLAYER_SMB="//server/path/to/movies"
#MPLAYER_SMB_OPTIONS="username=mplayer,password=mplayer"
# Language MPlayer should use (defaults to 'en' if not declared)
#MPLAYER_LANG=en
# hdparm
#
# !! WARNING !! WARNING !! WARNING !! WARNING !! WARNING !!
# hdparm provides a command line interface to various hard
# disk ioctls supported by the stock Linux IDE/ST-506 device
# driver. Use this utility with CAUTION, and at YOUR OWN RISK
# as it can PERMANENTLY DAMAGE YOUR SYSTEM!! Read up on the
# manual pages for more information.
#
# MPLAYER_HDPARM="-d1 -a8 -u1 -c1"
# CD/DVD device
#MPLAYER_CD_DVD="/dev/ide/host0/bus0/target0/lun0/cd"
# Video driver (defaults to 'x11' if not declared)
#MPLAYER_DRIVER="xv"
Ich weiss, iss jetzt n riessen Ding das ich hier hinmache, aber ich
weiss mir echt nicht mehr zu helfen .
Vielleicht gibts ja doch jemanden unter euch der das mal durchschauen könnt, und mir dann meine Fehler sagen kann .
Ich hab echt keine Ahnung .
Ich denk s hängt irgendwie mit der Einstellung von XFree und den
Sessions zusammen, aber da ich mich mit Linux, bis jetzt, überhaupt so schlecht auskenne, weiss ich einfach nicht was ich falsch mache .
Jo denne,
ich setz echt grosse Hoffnung in euch,
ihr seit wie's aussieht nämlich meine letzte Hoffnung .
Mit freundlichen Grüssen
euer Jonas
hat jemand ne Ahnung von Thinstation und der zugehörigen
Build - Routine TS-O-Matic (http://thinstation.org/) ????
Ich müh mich jetzt schon seit Tagen damit ab und krieg's nicht
gescheit zum laufen .
Ich würde gerne eine Minimal - Konfiguration für meinen uralt
Laptop machen, um dann per VNCViewer meinen Win2000 -
Rechner fernzusteuern .
Der Laptop ist ein 1996'er Dell Latitude XPi (P90ST) mit 90 MHrz,
12 mB RAM, ner Cirrus Logic SVGA Graphikkarte mit 800x600 und
16 Bit High Color .
Verbunden mit dem Win2000-Rechner ist er über ne Dockingstation
mit ner EthernetKarte die mir als Dell Ethernet Advanced Port Replicator (91C94) angezeigt wird .
Ich hab nen bischen rumgegoogelt und gelesen das diese wohl
SMC 9000-9200 kompatibel ist, was die Treiber angeht .
Ich post euch hier mal meine build.conf und meine thinstation.conf.buildtime :
################################################
### --- Thinstation Build Config --- ###
################################################
#
# This is Thinstation's basic setup file. In this file you decide which
# hardware, programs and features to be included in the Thinstation boot image
# generated by running "./build".
#
# You can customize/limit the possibilities in the thinstation.conf files later.
#
# Anything after a "#" is a comment. You activate "things" by removing the #
# and remove "things" by putting a # in front of them.
#
# First we define which modules to include. Modules are hardware drivers.
# NEVER include more than necessary - the more modules the longer boot time
################################################
### --- Modules to include in boot image --- ###
################################################
# --- Bus Modules
module agpgart # AGP bus module for use with AGP video cards
module pcmcia # PCMCIA Cards
module apm # Advanced power management
# --- PCMCIA/CardBus bridges
# Only include what you really need!
#module yenta_socket # CardBus card and (Yenta) bridge support (Very common)
#module i82365 # Intel i82365 compatible ISA-bus bridge support
#module tcic # Databook TCIC host bridge support (old systems)
# --- Network cards modules
# Have as few as possible
# --- Ethernet 10-100 Mbit Modules
#module 3c501 # 3c501 "EtherLink" support
#module 3c503 # 3c503 "EtherLink II" support
#module 3c505 # 3c505 "EtherLink Plus" support
#module 3c507 # 3c507 "EtherLink 16" support
#module 3c509 # 3c509/3c529 (MCA)/3c579 "EtherLink III" support
#module 3c515 # 3c515 ISA "Fast EtherLink"
#module 3c59x # 3c590/3c900 series (592/595/597) "Vortex/Boomerang" support
#module 8139too # RealTek RTL-8139 PCI Fast Ethernet Adapter support
# # VERY common in no-name network cards. Covers also 8129
#module 8139cp # RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support
#module ac3200 # Ansel Communications EISA 3200 support
#module amd8111e # AMD 8111 (new PCI lance) support
#module at1700 # AT1700/1720 support
#module b44 # Broadcom 4400 ethernet support
#module cs89x0 # CS89x0 support
#module de4x5 # Generic DECchip & DIGITAL EtherWORKS PCI/EISA
#module depca # DEPCA, DE10x, DE200, DE201, DE202, DE422 support
#module dgrs # Digi Intl. RightSwitch SE-X support
#module dmfe # Davicom DM910x/DM980x support
#module hp100 # HP 10/100VG PCLAN (ISA, EISA, PCI) support
#module e100 # EtherExpressPro/100 support (e100, Alternate Intel driver)
#module e2100 # Cabletron E21xx support
#module eepro # EtherExpressPro support/EtherExpress 10 (i82595) support
#module eepro100 # EtherExpressPro/100 support (eepro100, original Becker driver)
#module eexpress # EtherExpress 16 support
module epic100 # SMC EtherPower II
#module eth16i # ICL EtherTeam 16i/32 support
#module ewrk3 # EtherWORKS 3 (DE203, DE204, DE205) support
#module fealnx # Myson MTD-8xx PCI Ethernet support
#module forcedeth # nForce Ethernet support
#module hp-plus # HP PCLAN+ (27247B and 27252A) support
#module hp # HP PCLAN (27245 and other 27xxx series) support
#module lp486e # LP486E on board Ethernet
#module lance # AMD LANCE and PCnet (AT1500 and NE2100) support
#module ne io=0x300 # NE2000/NE1000 support
#module ne2k-pci # PCI version of NE-2000
#module natsemi # National Semiconductor DP8381x series PCI Ethernet support
#module ni5010 # Racal-Interlan (Micom) NI cards
#module ni52 # Racal-Interlan (Micom) NI cards
#module ni65 # Racal-Interlan (Micom) NI cards
#module pcnet32 # AMD PCnet32 PCI support
#module sis900 # SiS 900/7016 PCI Fast Ethernet Adapter support
# # Common in integrated motherboards
module smc-ultra # SMC Ultra support
module smc9194 # SMC 9194 support
#module starfire # Adaptec Starfire/DuraLAN support
#module sundance # Sundance Alta support
#module tlan # TI ThunderLAN support, Compaq Neteligent 10/100
#module typhoon # 3cr990 series "Typhoon" support
#module tulip # DECchip Tulip (dc21x4x) PCI support
#module via-rhine # VIA Rhine support (both Rhine I and II). Common in integrated motherboards
#module wd # WD80*3 support
#module winbond-840 # Winbond W89c840 Ethernet support
# --- Ethernet 1000 Mbit Modules
#module acenic # Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support
#module dl2k # D-Link DL2000-based Gigabit Ethernet support
#module e1000 # Intel(R) PRO/1000 Gigabit Ethernet support
#module ns83820 # National Semiconductor DP83820 support
#module hamachi # Packet Engines Hamachi GNIC-II support
#module yellowfin # Packet Engines Yellowfin Gigabit-NIC support
#module r8169 # Realtek 8169 Gigabit Ethernet support
#module sk98lin # Marvell Yukon Chipset / SysKonnect SK-98xx Support
#module tg3 # Broadcom Tigon3 support
# --- Token Ring modules
#module 3c359 # 3Com 3C359 Token Link Velocity XL adapter support
#module abyss # Madge Smart 16/4 PCI Mk2 support
#module ibmtr # IBM Tropic chipset based adapter support
#module lanstreamer # IBM Lanstreamer chipset PCI adapter support
#module olympic # IBM Olympic chipset PCI adapter support
#module smctr # SMC ISA/MCA adapter support
#module tmsisa # Generic TMS380 ISA support
#module tmspci # Generic TMS380 PCI support
#module mtok # Madge Token Ring Linux Driver
# --- PCMCIA Network Modules
#module 3c574_cs # 3Com 3c574 PCMCIA support
#module 3c589_cs # 3Com 3c589 PCMCIA support
#module pcnet_cs # NE2000 compatible PCMCIA support
#module smc91c92_cs # SMC 91Cxx PCMCIA support
#module xircom_cb # Xircom CardBus supportupport
# --- Wireless Modules
#module orinoco_pci # Prism 2.5 PCI 802.11b adaptor support (EXPERIMENTAL)
#module orinoco_cs # Hermes PCMCIA card support
#module airo_cs # Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards
# --- Modem Modules
#module acm # USB Modem support (CDC ACM)
# -- USB Palm Devices
#module visor # USB Handspring Visor / Palm m50x / Sony Clie Driver
# -- Sound Modules
#module ad1816 # AD1816(A) based cards
# # ad1816=<io>,<irq>,<dma>,<dma2>
#module ad1848 # Microsoft Sound System support
# # ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]
#module cs4232 # Crystal CS4232 based (PnP) cards
#module cs4281 # Crystal Sound CS4281
#module cs46xx # Crystal SoundFusion
#module emu10k1 # Creative SBLive! (EMU10K1)
#module es1371 # Creative Ensoniq AudioPCI 97
#module es1370 # Ensoniq AudioPCI
#module esssolo1 # ESS Technology Solo1
#module gus # Gravis Ultrasound support
# # gus=<io>,<irq>,<dma>,<dma2>
#module i810_audio # Intel ICH (i8xx), SiS 7012, NVidia
# # nForce Audio or AMD 768/811x
#module mad16 # OPTi MAD16 and/or Mozart based cards
# # mad16=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
#module maestro # ESS Maestro, Maestro2, Maestro2E driver
#module maestro3 # ESS Maestro3/Allegro driver
#module nm256_audio # NM256AV/NM256ZX audio support
#module pas2 # ProAudioSpectrum 16 support
# # pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
#module pss # PSS (AD1848, ADSP-2115, ESC614) support
# # pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>
#module sb io=0x220 irq=5 dma=1 dma16=5 # 100% Sound Blaster compatibles
#module sb isapnp=1 # 100% Sound Blaster compatibles
#module sgalaxy # Aztech Sound Galaxy (non-PnP) cards
# # sgalaxy=<io>,<irq>,<dma>,<dma2>,<sgbase>
#module sonicvibes # S3 SonicVibes
#module sscape # Ensoniq SoundScape support
# # sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>
#module trident # Trident 4DWave DX/NX, SiS 7018 or
# # ALi 5451 PCI Audio Core
#module trix # MediaTrix AudioTrix Pro support
#module via82cxxx_audio # VIA 82C686 Audio Codec
#module ymfpci # Yamaha YMF7xx PCI audio (native mode)
# -- USB Devices
#module usb-hid # Needed for USB keyboards and mice
#module usb-storage # Needed for USB-Sticks
#module usb-printer # Needed for USB-Printers
# -- Storage Devices
module ide-floppy # LS-120, Iomega Zip
module floppy # Floppy Disk Drive Support
#module cdrom # CD-Rom Drive Support
# -- Filesystem Support
# -- Every mounted device needs a filesystem, choose which ones are supported below.
module isofs # ISO9960 file system support for CDRoms
module vfat # Fat and VFat file system support
#module ext2 # Ext2 file system support
#module ext3 # Ext3 file system support
#module supermount # Supermount support for auto unmounting of removable media
#module nfs # NFS file system support
#module smbfs # Samba client FS Support, allows you to mount smb filesystems
#################################################
### --- Packages to include in boot image --- ###
#################################################
# A package is a program or utility.
# Any packages may be added as "package" or "pkg".
# If defined as a "package" the program is included in the boot image.
# If defined as a "pkg" the program is added from outside the image.
# Normally use "package", and only "pkg" if the image approaches 16 MB or
# you know what you are doing.
# --- Packages to include in boot image
# --- Packages below may be "package" or "pkg"
#package hwclock # Utility to set system time from hardware clock
#package sound-esd # Enable one of these modules if you want to be able to control
#package sound-nasd # sound on your thinstation from another computer or
# your remote session.
# --- X related packages
#package xorg6-tinyx # TinyX Xvesa server (for low memory machines)
# works with ICA too, is slower, don't choose any X modules with
# this server, you don't need anything else.
# Otherwise choose from Xfree 3 or 4 (4 is recommended)
package xf3-svga # XF86_SVGA 3.3.6 server
#package xf3-s3 # XF86_S3 3.3.6 server
#package xf3-vmware # VMWare X server for development
#package xorg6vnc # Xorg VNC Server Module. With this package you can
# connect to the TS client's desktop from a java
# browser on "http://<TS ip>:5800
# --- Xorg6R7.0
# General Xorg6R7.0 video drivers:
# Only include what you really need!
#package xorg6-apm # Alliance ProMotion video driver
#package xorg6-ark # Ark Logic video driver
#package xorg6-ati # ATI video driver
#package xorg6-chips # Chips and Technologies video driver
package xorg6-cirrus # Cirrus Logic video driver
#package xorg6-cyrix # Cyrix video driver
#package xorg6-glint # GLINT/Permedia video driver
#package xorg6-i128 # Number 9 I128 video driver
#package xorg6-i740 # Intel i740 video driver
package xorg6-i810 # Intel 8xx integrated graphics chipsets
#package xorg6-mga # Matrox video driver
#package xorg6-neomagic # Neomagic video driver
#package xorg6-nsc # Nsc video driver
#package xorg6-nv # NVIDIA video driver
#package xorg6-r128 # ATI Rage 128 video driver
#package xorg6-radeon # ATI RADEON video driver
#package xorg6-rendition # Rendition video driver
#package xorg6-s3 # S3 video driver
#package xorg6-s3virge # S3 ViRGE video driver
#package xorg6-savage # S3 Savage video driver
#package xorg6-siliconmotion # Silicon Motion video driver
#package xorg6-sis # SiS video driver
#package xorg6-tdfx # 3Dfx video driver
#package xorg6-tga # DEC TGA video driver
#package xorg6-trident # Trident video driver
#package xorg6-tseng # Tseng Labs video driver
package xorg6-vesa # Generic VESA driver, use this if you don't know what to use
#package xorg6-vga # VGA 320x200 8 bit
#package xorg6-via # VIA video driver
#package xorg6-vmware # VMware SVGA video driver
# --- Keyboard layouts (Language/Country)
#package keymaps-ar # Arabic
#package keymaps-cs # Czech
#package keymaps-da # Danish
package keymaps-de # German
#package keymaps-de_ch # German-Switzerland
#package keymaps-en_gb # English-Great Britian
#package keymaps-en_in # English-United States International
#package keymaps-en_nz # English-New Zealand
package keymaps-en_us # English-United States
#package keymaps-es # Spanish
#package keymaps-et # Estonian
#package keymaps-fr_be # French-Belgium
#package keymaps-fr_ca # French-Canada
#package keymaps-fr_ch # French-Switzerland
#package keymaps-fr # French
#package keymaps-hr # Croatian
#package keymaps-hu # Hungarian
#package keymaps-it # Italian
#package keymaps-ja # Japanese
#package keymaps-la # Latin
#package keymaps-lt # Lithuanian
#package keymaps-lv # Latvian
#package keymaps-mk # Macedonian
#package keymaps-nl # Dutch
#package keymaps-no # Norwegian
#package keymaps-pl # Polish
#package keymaps-pt_br # Portuguise-Brazil
#package keymaps-pt # Portuguise
#package keymaps-ro # Romanian
#package keymaps-ru # Russian
#package keymaps-sv_fi # Swedish-Finland
#package keymaps-sv # Swedish
#package keymaps-sl # Slovenian
#package keymaps-th # Thai
#package keymaps-tr # Turkish
# --- Connection Package types
# Choose *at least* one!
#package rdesktop # X RDP client for Windows Terminal Services (ver 1.3.1)
#package rdesktop_svga # SVGA RDP client, This is Version 1.1 of rdesktop Only
# Use this for low memory machines
package vncviewer # VNC client (vncviewer)
#package ica # Citrix ICA client support
#package tarantella # Tarantella client support
#package ica_wfc # Citrix ICA manager
#package xnest # XDM in a window client
#package rxvt # Light Xterm Client (vt102)
#package xterm # Xterm Client (vt220)
#package ssh # Secure Shell client
#package tn5250 # 5250 terminal emulator
#package dillo # Dillo light web browser
#package nx # No Machine NX client
# --- Window Managers
# Choose no more than 1 window manager
# Not needed if you don't want to manage windows
package blackbox # "Blackbox" window manager. Makes TS a light workstation.
#package icewm # "ICEWM" window manager. Makes TS a light workstation.
# Is a little bigger than blackbox
# --- Window Manager Utils
#package xtdesk # Adds icons to desktop
# --- Other services
package www # Web access to client. From a browser: "http://<IP number>"
# The standard page is for general user settings, administrative access
# is on port 6800
#package lp_server # Remote printing daemon (LaserJet compatible)
#package lpr # LPR Print Server, for use with samba-server package
#package tftpd # TFTP, built in tftpd server
# Useful for making a tftpserver for thinstation on a WAN
# over a slow link
#package samba-server # Samba server FS Support, allows you to share
# local floppy/cdrom/hd/printer to other Windows
# PCs; Needs supermount for removeable media
# --- Miscellaneous
#package e3 # Basic vi like Editor
#package debug # Debug support, adds strace and other commands
# not recommended for normal use.
########################################
### --- Miscellaneous Parameters --- ###
########################################
param rootpasswd klar, setz ich noch ein # Do Change! Console/telnet password for Root
# If this is enabled, Telnetd will be enabled
param xorgvncpasswd klar, setz ich noch ein # VNC Access Password
#param storagepasswd pleasechangeme # Password for storage server
#param dialuppasswd pleasechangeme # Password for dialin account
#param sambapasswd pleasechangeme # Password for samba shares when using user mode security
param bootlogo false # Want a backgound picture during boot
param bootresolution 800x600
param defaultconfig thinstation.conf.buildtime # The file with default setup
# no other config file is found
# during boot
param basename thinstation # used for all config/tftp file names
param basepath . # used to determine path to tftp files
param localpkgs false # to determine is PKG files are to be loaded locally
param fulllocales false # Use full locale support for packages
param icaencryption false # Use ica encryption support, add 290k to image
param bootvebosity 3 # Increased vebosity when booting TS
# 0 no verbose messages
# 1 boot
# 2 network
# 4 init
# 8 kernel
# 16 modules
# 32 packages
# 64 email bootlog file to SMTP server & user set in
# thinstation.conf file. This will only work
# if networking is working.
#
# Combinations can be used, ie 12 does Kernel and Module Messages
#package emelfm
#package evilwm
#package links #Links web browser supporting HTML 4, SSL and Javascript
#package lprng # LPRng
#package mplayer # MPlayer - The Movie Player (www.mplayerhq.hu)
#package sylpheed # Sylpheed-claws E-mail client
#package xcalc # The X pocket calculator, TI or HP style
#package xpdf # Xpdf - http://www.foolabs.com/xpdf - PDF reader
#package firefox # Firefox web browser
#package flash # Flash, you must have also downloaded the firefox package
#package cdparanoia # "rips" cd audio tracks, converting them to audio files
#package libao # required audio library for playback
#package mpg321 # play and decode mp3 audio
#package vorbis-tools # encoding, decoding and playback for ogg format
#package sox # multi-format sound (mp3, wav, ogg, etc.) translator/player
#package xmms # winamp like mp3-player
#################################################
# --- Thinstation sample configuration file --- #
#################################################
#
# This file must be named "thinstation.conf<xxx>" where <xxx> can be:
# .buildtime Defines the defaults build into the image (note the leading .)
# .network Default config file loaded from the TFTP server.
# .user Config file on local storage.
# -<name> Specific config file on the TFTP server for the terminal
# "name" (e.g. thinstation.conf-paul). Requires thinstation.hosts.
# .group-<id> Config file for a group of terminals (e.g. with printer setup
# for those terminal with local printers. Requires thinstation.hosts.
# -<IP> Specific config file on the TFTP server for the terminal with
# the IP number <IP> specified.
# -<MAC> Specific config file on the TFTP server for the terminal with
# the MAC address specified.
# --- General Options
#
# AUDIO_LEVEL Audio Level for sound, 0-100
# KEYBOARD_MAP Keyboard layout
# TIME_ZONE Used to set time zone on TS client by entering the UTC offset.
# This can be set automatically if the appropriate dhcpc option is selected
# (Option 2, time offset in seconds)
# SYSLOG_SERVER Log server ip address or hostname.
# If the work "local" is used, then syslog starts logging locally
# If not specified syslogd is not loaded.
# USB_ENABLED Enable USB Drivers into memory if USB package is chosen
# DAILY_REBOOT Will reboot server if up over a day and one of the session
# types is closed
# AUTOPLAYCD If enabled this will autoplay music cds when inserted.
# CUSTOM_CONFIG Allows choosing custom boot config, On/Off
# RECONNECT_PROMPT This displays the reconnection/shutdown options for when a session is ended
#
# OFF No reconnect prompt
# ON Reconnect prompt will be displayed
# MENU Shows a menu with a shutdown and reconnection option
# MENUXX As MENU option, but the XX is a time period in minutes.
# After XX minutes shutdown will occur unless the reconnect option
# is choosen
AUDIO_LEVEL=0
KEYBOARD_MAP=de
TIME_ZONE="UTC-2:00"
SYSLOG_SERVER=local
USB_ENABLED=Off
DAILY_REBOOT=On
#AUTOPLAYCD=On
CUSTOM_CONFIG=Off
RECONNECT_PROMPT=On
# --- Default Settings for all sessions
#
# SCREEN Display number to run the X server on
# AUTOSTART ON Application will be executed immediately at startup
# OFF Application will appear in a menu to be started manually
# WORKSPACE Workspace in the window manager to run the application in
# ICONMODE MANUAL Default sessions are not created in window manager/desklaunch
# AUTO Default sessions types are created in window manager/desklaunch
SCREEN=0
WORKSPACE=1
AUTOSTART=On
ICONMODE=AUTO
# --- Citrix ICA Specific Options
#
# GLOBAL Settings
#ICA_USE_SERVER_KEYBOARD Use default server keyboard, otherwise use KEYBOARD_MAP
# variable
#ICA_BROWSER_PROTOCOL Broswer protocol, can be HTTPonTCP or UDP
#
# APPLICATION SET settings
#ICA_ENCRYPTION Encryption level for ICA
# Valid Settings Below
# "Basic"
# "RC5 (128 bit - Login Only)"
# "RC5 (40 bit)"
# "RC5 (128 bit)"
# "RC5 (56 bit)"
#ICA_COMPRESS Compression, On/Off
#ICA_AUDIO Audio, On/Off
#ICA_AUDIO_QUALITY Audio Quality, Low, Medium, High
#ICA_PRINTER This will turn on ICA autocreate printers, see printer section
# for details, On/Off
#
# NOTE: You must have the lpr package included for this option
# to work.
#
#ICA_APPLICATION_SET Published Application (Not needed if using
# ICA_SERVER)
#ICA_SERVER Server to Connect to (Not needed if using
# ICA_APPLICATION_SET, but needed if the ICA-Masterbrowser
# is not on the local network.)
#ICA_WFCLIENT_type_specific This allows you to specify specific config file details for global ica
# parameters any parameter can be changed with this setting. An example of this is
# ICA_WFCLIENT_CLIENTDRIVE="On"
# See your application manual for documentation on the settings which
# can be used.
#ICA_USE_SERVER_KEYBOARD=Off
#ICA_BROWSER_PROTOCOL=HTTPonTCP
#ICA_SERVER=
#ICA_ENCRYPTION=Basic
#ICA_COMPRESS=On
#ICA_AUDIO=On
#ICA_AUDIO_QUALITY=Low
#ICA_PRINTER=Off
#ICA_SEAMLESS_WINDOW=Off
# --- Session Options
#
# Note: # is a number equal to or greater than 0
#
# SESSION_#_TITLE Title description for SESSION. Needed for replimenu.
# SESSION_#_TYPE Package type, choose beetwen:
# - vncviewer Start vncviewer in X
# - rdesktop Start rdesktop in X
# - rdesktop_svga Start svga rdesktop, based on rdesktop 1.1 code
# for low memory machines
# - x Start x-terminal session (xdm)
# - xnest Start x-terminal session (xdm) from within blackbox
# - ssh Start ssh client in linux console
# - telnet Start telnet client in linux console
# - ica Start Citrix ICA client in X
# - ica_wfc Start ICA Manager
# - blackbox Start blackbox window manager session
# - icewm Start icewm window manager session
# - dillo Start Web Browser in X
# - tftpd Start tftp daemon
# - tarantella Start tarantella client
# - rxvt Start light xterm client
# - xterm Start xterm client
# - tn5250 Start AS400 client in linux console
# - nx Start NX Client Session
# SESSION_#_SCREEN Display number to run the X server on
# SESSION_#_AUTOSTART ON Application will be executed immediately at startup
# OFF Application will appear in a menu to be started manually
# SESSION_#_CUSTOM_CONFIG ON Allows choosing custom config for when session starts
# OFF Session boots normally
# SESSION_#_ICON ON Places Icon on Desktop if package Desklaunch is selected and
# in Window Manager Main Menu
# SUBMENU Places Icon on Desktop if package Desklaunch is selected and
# in a Submenu within the window manager
# SESSION_#_WORKSPACE Workspace to run program on in a window manager
# SESSION_#_type_SERVER IP address/hostname of the server
# SESSION_#_type_OPTIONS Command line options for the session type
#
# SESSION_#_type_specific This allows you to specify specific config file details for certain session
# types. Currently support is NX and ICA. Any configuration file setting
# can be changed with this setting. An example of this is
# SESSION_0_NX_GENERAL_DESKTOP="Gnome"
# SESSION_0_ICA_APPSRV_USEFULLSCREEN="Yes"
# See your application manual for documentation on the settings which
# can be used.
# Individual Session Settings, override defaults
#
# IMPORTANT: Make sure you minimum have a SESSION_0. Otherwise you will get an error
# on boot. You may have additional sessions: SESSION_1, SESSION_2 ...
# SESSION_0 is on ctrl-alt-F3
# SESSION_1 is on ctrl-alt-F4
# ... etc.
SESSION_0_TYPE=blackbox
#SESSION_1_TYPE=ica
#SESSION_1_ICA_APPLICATION_SET="Microsoft Word"
#SESSION_1_ICA_OPTIONS="-username donald -clearpassword qwak -domain disney"
#SESSION_1_ICON=ON
#SESSION_2_TYPE=ica
#SESSION_2_ICA_SERVER=ICA
#SESSION_3_TYPE=ica_wfc
# The -a option here specifies the color depth
# Note certain servers support certain color depths, wrong settings with this
# May cause your connection to fail.
#SESSION_4_TITLE="Big Bad Server Donald"
#SESSION_4_TYPE=rdesktop
#SESSION_4_SCREEN=1
#SESSION_4_SCREEN_POSITION=2
#SESSION_4_RDESKTOP_SERVER=192.168.1.1
#SESSION_4_RDESKTOP_OPTIONS="-u user -p password -a 16"
#SESSION_4_AUTOSTART=Off
#SESSION_#_TITLE="Big Bad Server Road Runner"
#SESSION_#_TYPE=rdesktop
#SESSION_#_SCREEN=1
#SESSION_#_RDESKTOP_SERVER=192.168.1.1
#SESSION_#_RDESKTOP_OPTIONS="-u 'fred' -a 8"
#SESSION_#_AUTOSTART=Off
#SESSION_#_TYPE=rxvt
#SESSION_#_SCREEN=1
#SESSION_#_RXVT_OPTIONS="-bg black -cr green -fg white -C -sl 500"
#SESSION_#_WORKSPACE=2
#SESSION_#_TYPE=blackbox
#SESSION_#_SCREEN=1
SESSION_1_TYPE=x
#SESSION_#_SCREEN=2
SESSION_1_X_SERVER=192.168.1.2
SESSION_1_X_OPTIONS="-indirect"
#SESSION_#_AUTOSTART=Off
#SESSION_#_TYPE=xnest
#SESSION_#_X_SERVER=192.168.1.3
#SESSION_#_X_OPTIONS="-query"
#SESSION_#_AUTOSTART=On
#SESSION_#_TYPE=telnet
#SESSION_#_TELNET_SERVER=192.168.1.2
#SESSION_#_TYPE=ssh
#SESSION_#_SSH_SERVER=192.168.1.2
SESSION_2_TYPE=vncviewer
SESSION_2_VNCVIEWER_SERVER=192.168.1.2 #zB. kommt hier die
# IP von meinem Win2000 hin ??
#SESSION_#_TYPE=tn5250
#SESSION_#_TN5250_SERVER=192.168.1.2
#SESSION_#_TYPE=nx
#SESSION_#_TITLE="Gnome"
#SESSION_#_NX_ADVANCED_ENABLE_SSL_ENCRYPTION="true"
#SESSION_#_NX_GENERAL_DESKTOP="Gnome"
#SESSION_#_NX_GENERAL_SERVER_HOST="nx-server-ip"
#SESSION_#_NX_GENERAL_REMEMBER_PASSWORD="true"
#SESSION_#_NX_GENERAL_RESOLUTION="fullscreen"
#SESSION_#_NX_GENERAL_SESSION="Unix"
#SESSION_#_TYPE=nx
#SESSION_#_TITLE="Firefox"
#SESSION_#_NX_ADVANCED_ENABLE_SSL_ENCRYPTION="true"
#SESSION_#_NX_GENERAL_DESKTOP="Console"
#SESSION_#_NX_GENERAL_SERVER_HOST="nx-server-ip"
#SESSION_#_NX_GENERAL_REMEMBER_PASSWORD="true"
#SESSION_#_NX_GENERAL_COMMAND_LINE="/usr/local/firefox/firefox"
#SESSION_#_NX_GENERAL_SESSION="Unix"
#SESSION_#_NX_GENERAL_ONLY_CONSOLE="false"
#SESSION_#_TYPE=nx
#SESSION_#_TITLE="Windows"
#SESSION_#_NX_ADVANCED_ENABLE_SSL_ENCRYPTION="true"
#SESSION_#_NX_GENERAL_DESKTOP="RDP"
#SESSION_#_NX_GENERAL_RESOLUTION_VALUE="fullscreen"
#SESSION_#_NX_GENERAL_SERVER_HOST="nx-server-ip"
#SESSION_#_NX_GENERAL_SESSION="Windows"
#SESSION_#_NX_WINDOWS_SESSION_SERVER="windows-server-ip"
#SESSION_#_NX_WINDOWS_SESSION_AUTHENTICATION="1"
#SESSION_#_TYPE=icewm
# --- PKG Options
#
# PKG_PACKAGES Choice of packages to download for PKG
# You can also use PKG_PACKAGES1-8 for additional package selections
# This is useful for using multiple network group files
# PKG_PREFIX Download PKGs from a subdir of /tftpboot or PKG Path if PKG_PATH
# is set in thinstation.conf
# PKG_PATH Path to PKG files if not using tftpboot
# Floppy: /mnt/floppy
# CD-ROM: /mnt/cdrom
# HD: /mnt/disc/disc0/part1 (first disc, first partition)
# MOD_PACKAGES Choice of modules to download for MPKG
# You can also use MOD_PACKAGES1-8 for additional package selections
# This is useful for using multiple network group files
# MOD_PREFIX Downloads and insmod's a module from a subdir of /tftpboot
# if MOD_PREFIX is set in thinstation.conf
#PKG_PACKAGES="blackbox rxvt"
#PKG_PREFIX=pkg
#PKG_PATH=/mnt/cdrom
#MOD_PACKAGES="usb-hid usb-storage"
#MOD_PREFIX=modules
# --- X Server Options
#
# SCREEN_RESOLUTION Screen resolutions available in the workstations
# SCREEN_COLOR_DEPTH Number of bits per pixel (8,16,24)
# SCREEN_HORIZSYNC Monitor horizontal sync frequency in Khz.
# If left blank Xorg will try to detect with DDC
# SCREEN_VERTREFRESH Monitor vertical refresh frecuency in Hz.
# If left blank Xorg will try to detect with DDC
# SCREEN_X_FONT_SERVER IP address or hostname of the font server for X
#
# Screen Saver Settings
# SCREEN_BLANK_TIME Minutes to X session goes blank
# SCREEN_STANDBY_TIME Minutes to X session goes into standby mode
# SCREEN_SUSPEND_TIME Minutes to X session goes into suspend mode
# SCREEN_OFF_TIME Minutes to X session turn off
#
# MOUSE_PROTOCOL Mouse protocol type (Microsoft, PS/2, etc.)
# (mouse is autodetected, use this only if it fails)
# MOUSE_DEVICE Mouse device: /dev/ttyS0 -> COM1
# /dev/ttyS1 -> COM2
# /dev/ttyS2 -> COM3
# /dev/ttyS3 -> COM4
# /dev/psaux -> PS/2 mouse port
# /dev/input/mice -> USB mouse (needs USB package)
# MOUSE_RESOLUTION Mouse resolution
# --- Advanced XServer Options - Experts Only
# X_DRIVER_NAME Driver for X, this will override the autodetection scripts
# X_DRIVER_BUSID Screen Card BusID
# X_DRIVER_OPTION1-4 Addditional options for driver
SCREEN_RESOLUTION="800x600 | 640x480 | *"
SCREEN_COLOR_DEPTH="16 | 8 | *"
#SCREEN_HORIZSYNC="30-64 | *"
#SCREEN_VERTREFRESH="56-87 | 60 | 56 | 70 | 72 | 75"
#SCREEN_X_FONT_SERVER=192.168.1.2:7100
SCREEN_BLANK_TIME=10
SCREEN_STANDBY_TIME=20
SCREEN_SUSPEND_TIME=30
SCREEN_OFF_TIME=60
#MOUSE_PROTOCOL=PS/2
#MOUSE_DEVICE=/dev/psaux
MOUSE_RESOLUTION=100
# --- Advanced Options - Experts Only
#X_DRIVER_NAME="mga"
#X_DRIVER_BUSID="PCI:1:0:0"
X_DRIVER_OPTION1="swcursor On"
#X_DRIVER_OPTION2="ActiveDevice CRT"
#X_DRIVER_OPTION3="noDDC Off"
#X_DRIVER_OPTION4="UseBios Off"
#X_DRIVER_OPTION5="ShadowFB Off"
# --- Printing Options
#
# PRINTER_0_NAME Workstation Printer Name, Can be Any Valid Name
# If you have turned ICA_PRINTER=ON then this is the
# name of the printer driver
# PRINTER_0_DEVICE Workstation printer device (if not specified devices
# are not loaded).
# /dev/printers/[0-2] for parallel ports
# /dev/ttyS[0-3] for serial ports
# /dev/usb/lp[0-2] for USB printers
#
# PRINTER_0_TYPE P for parallel, S for serial, U for USB printer
# PRINTER_0_OPTIONS Serial port options.
# PRINTER_1_* See PRINTER_0_*
# PRINTER_2_* See PRINTER_0_*
# PRINTER_3_* See PRINTER_0_*
#PRINTER_0_NAME="parallel"
#PRINTER_0_DEVICE=/dev/printers/0
#PRINTER_0_TYPE=P
#PRINTER_1_NAME="serial"
#PRINTER_1_DEVICE=/dev/ttyS1
#PRINTER_1_TYPE=S
#PRINTER_1_OPTIONS="speed 38400 -imaxbel"
#PRINTER_2_NAME="usb"
#PRINTER_2_DEVICE=/dev/usb/lp0
#PRINTER_2_TYPE=U
#PRINTER_3_NAME="usb"
#PRINTER_3_DEVICE=/dev/usb/lp0
#PRINTER_3_TYPE=U
#ICA Autocreate Printer Example
#PRINTER_0_NAME="HP LaserJet Series II"
#PRINTER_0_DEVICE=/dev/printers/0
#PRINTER_0_TYPE=P
# --- Permanent Storage Options
#
# STORAGE_PATH Path to where storage device is mounted to save
# profile settings. This should be one of
# /mnt/usbdevice/busX.targetX.lunX/partX or disc
# /mnt/floppy
# /mnt/disc/discX/partX
# /mnt/nfs
# /mnt/smb
#
# Note that the profile settings are stored under
# a subfolder for this path. So the path to the
# stored settings would be something like
# /mnt/floppy/thinstation.profile
# See the FAQ on the website for more details on this
#
# Also checkout README.IMPORTANT for the valid
# config files which you can place here
# a typical file to store config file settings is
# /mnt/floppy/thinstation.profile/thinstation.user
#
# Also note that the .profile can be changed by using
# the below STORAGE_PREFIX
# STORAGE_SERVER This is the path to the SMB or NFS server, ie
# server:/path/to/profile
# STORAGE_USER This is the username for SMB mounts, password is
# defined at build time in build.conf
# STORAGE_PREFIX This is prefex for the folder name to store settings
# in on the storage device. You can also use one of the
# special characters below.
#
# M = Mac Address
# H = Hostname
# I = Ip Address
#
# Note default prefix for storing the profile is
# .profile
# STORAGE_CONFIG1-8 This is the path for any user defined settings
# which will always override the profile path above
# The files are tried on order on each device specified
#STORAGE_PATH=/mnt/nfs
#STORAGE_SERVER=bigserver:/opt/thinstation
#STORAGE_USER=duck
#STORAGE_PREFIX=H
#STORAGE_CONFIG1=/mnt/floppy
#STORAGE_CONFIG2=/mnt/cdrom
#STORAGE_CONFIG3=/mnt/disc/disc1/part1
#STORAGE_CONFIG4=/mnt/usbdevice/busX.targetX.lunX/partX or disc
# --- Samba Options
#
# SAMBA_SERVER_ENABLED Enable Samba Server Daemons, On/Off
# SAMBA_SECURITY Type of security, USER, DOMAIN, SERVER
# SAMBA_SERVER Server for security
# SAMBA_WINS Server Name to Enable Samba to be a WINS Client
# SAMBA_HARDDISK Enable Harddrive support, On/Off
# SAMBA_CDROM Enable CDRom Support, On/Off
# SAMBA_FLOPPY Enable Floppy Support, On/Off
# SAMBA_PRINTER Enable Printer Support, On/Off
# SAMBA_USB Enable USB Support, On/Off
#SAMBA_SERVER_ENABLED=Off
#SAMBA_WORKGROUP=BigPeople
#SAMBA_SECURITY=Server
#SAMBA_SERVER=BadMan
#SAMBA_WINS=BadMan
#SAMBA_HARDDISK=Off
#SAMBA_CDROM=On
#SAMBA_FLOPPY=On
#SAMBA_PRINTER=On
#SAMBA_USB=Off
# --- Networking Options
#
# NET_HOSTNAME Hostname to use if not using a thinstation.hosts file, note
# that the machine MAC address will replace any * if used.
# NET_REMOTE_ACCESS_FROM List of hostnames/ip address accepted by the server
# for remote control, used by telnetd and www packages
# NET_SMTP_SERVER Email server address for error logs
# NET_SMTP_EMAIL Email address of administrator
# NET_TELNETD Enables built-in telnetd server package
#
#NET_HOSTNAME=donald
#NET_HOSTNAME=ts_*
#NET_SMTP_SERVER=donald
#NET_SMTP_EMAIL=donald@duck.org.nz
#NET_TIME_SERVER=mickey
#NET_TELNETD_ENABLED=On
#NET_REMOTE_ACCESS_FROM="duck.quak.org.au 192.168.0.0 .disney.us"
# --- For use in thinstation.conf.buildtime only:
#
# NET_USE_DHCP Enable DHCP Resolution, On/Off
# NET_IP_ADDRESS IP Address of client
# NET_MASK Network mask of client
# NET_GATEWAY IP Address of gateway
# NET_USE_TFTP Use tftp server for config file, On/Off
# NET_DNS1 DNS Server 1
# NET_DNS2 DNS Server 2
# NET_DNS_SEARCH Default DNS domain to search
# NET_ALTERNATE_TFTP Alternate tftp server for vmware or non-standard dhcp servers
#NET_USE_DHCP=Off
#NET_IP_ADDRESS=192.168.0.1
#NET_MASK=255.255.255.0
#NET_GATEWAY=192.168.0.254
#NET_USE_TFTP=Off
#NET_DNS1=192.168.0.2
#NET_DNS2=192.168.0.3
#NET_DNS_SEARCH=cartoons.org.nz
#NET_ALTERNATE_TFTP=192.168.0.4
# --- Wireless support (DHCP only!)
#
#WIRELESS_ESSID # ESSID (extended network name) : My Network, any
#WIRELESS_NWID # NWID/Domain (cell identifier) : 89AB, 100, off
#WIRELESS_MODE # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
#WIRELESS_FREQ # 2.422G, 2.46G (frequency)
#WIRELESS_CHANNEL # 1, 2, 3 (channel)
#WIRELESS_SENS # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
#WIRELESS_RATE # Bit rate : auto, 1M, 11M
#WIRELESS_RTS # RTS threshold : off, 500
#WIRELESS_FRAG # Fragmentation threshold : off, 1000
#WIRELESS_IWCONFIG # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
#WIRELESS_IWSPY # iwspy parameters : + 01:23:45:67:89:AB
#WIRELESS_IWPRIV # iwpriv parameters : set_port 2, set_histo 50 60
#WIRELESS_KEY # Encryption key : 4567-89AB-CD, s
assword#WIRELESS_ESSID="ssid"
#WIRELESS_NWID=""
#WIRELESS_MODE="managed"
#WIRELESS_FREQ=""
#WIRELESS_CHANNEL=""
#WIRELESS_SENS=""
#WIRELESS_RATE=""
#WIRELESS_RTS=""
#WIRELESS_FRAG=""
#WIRELESS_IWCONFIG=""
#WIRELESS_IWSPY=""
#WIRELESS_IWPRIV=""
#WIRELESS_KEY="abcdef"
# --- HD Update options
#
# HDUPDATE_ENABLED=Y Enable Update
# HDUPDATE_WS_VERSION Version of files on workstation (set in thinstation.buildtime only)
# HDUPDATE_SERVER_VERSION Version of files on server (set in both buildtime and network)
# This should be set in buildtime to match the WS_VERSION to prevent
# unintended upgrades
#
# HDUPDATE_SERVER tftp server name
# HDUPDATE_PATH Path to files /ts/update
# HDUPDATE_FORCE Force install even if not needed
# HDUPDATE_FILES List of files to upgrade
# HDUPDATE_DELETE List of files to delete (no sanity checks, use with caution)
#HDUPDATE_WS_VERSION=1
#HDUPDATE_ENABLED=Y
#HDUPDATE_SERVER_VERSION=CO.29
#HDUPDATE_SERVER=roadrunner
#HDUPDATE_PATH=/ts/update
#HDUPDATE_FORCE=N
# Set the list of files to download
#HDUPDATE_FILES="vmlinuz hires lowres syslinux.cfg thin.txt firefox.pkg flash.pkg"
#HDUPDATE_FILES="hires lowres"
#HDUPDATE_FILES="lowres"
#HDUPDATE_FILES="hires"
#HDUPDATE_FILES="syslinux.cfg thin.txt"
#**** EXPERIMENTAL ****
# Dual Head Support
#
# This allows two seperate X sessions to be started with seperate input devices. This allows
# effectively two seperate machines within the same PC. You will need seperate screen cards
# to enable this. It is best to use with 1 AGP card and 1 PCI card.
# Check out http://www.ltn.lv/~aivils/eng-video.html for a list of known compatable screen cards
# Input Device support should be:
#
# Primary mouse and keyboard PS/2
# Secondary mouse and keyboard USB
#
# There is some basic detection scripts for this, but these will need to be improved in TS 3.0.
# If thinstation doesn't detect both a USB keyboard and mouse it will default back to dual
# screen support, not dual head.
#
# This is not considered stable. If you exit the session, or try to change to a console screen
# with Alt-F1 etc... it will probably crash the machine. If it doesn't work with your hardware
# there is nothing that can be done about it.
# The kernel Advanced Power Management module is disabled when using dual screen as it causes the
# second screen to crash.
# Note the below option only supports 1-2, anything more than two won't work. This is provided
# for future development, to create a machine with more than two seperate sessions.
# SESSION_#_SCREEN_POSITION 1-X When using dual screen support you can specify the position
# of each session. This allows to seperate sessions to be on
# seperate screens. If only 1 session is in use, this option will
# make no differnece. You can specify between 1+ positions
# Sylpheed settings
#SYLPHEED_USENFS=N # store/get settings on NFS. If set to 'N' the
# files are created at package initialization,
# using settings below, which are then placed
# in $HOME/.sylpheed
# If set to 'Y' the user is asked to enter his/her
# account settings at first time startup and the
# settings are stored in $HOME/.sylpheed , which
# is symlinked to /mnt/nfs/$CLIENT_MAC/.sylpheed
#SYLPHEED_ACCOUNTNAME="Account1" # account description
#SYLPHEED_FULLNAME="Joe Sixpack" # full user name
#SYLPHEED_MAILADDRESS="joe@mycompany.com" # email address
#SYLPHEED_ORGANIZATION="Thinstation User" # organization
#SYLPHEED_PROTOCOL=3 # 0 = POP3
# 1 = POP3 w/ APOP
# 2 = ???
# 3 = IMAP4
# 4 = NNTP
# 5 = local mailbox
# 6 = SMTP only
#SYLPHEED_RECEIVESERVER=my.pop3-or-imap4.server # IMAP4/POP3 servername
#SYLPHEED_SMTPSERVER=my.smtp.server # SMTP servername
#SYLPHEED_NNTPSERVER=my.nntp.server # NNTP servername
#SYLPHEED_USERID="joe" # IMAP4/POP3 username
#SYLPHEED_PASSWD=secret # IMAP4/POP3 password - will be encrypted at
# first-time start
#SYLPHEED_PLUGINS="dillo" # specify which plugins should be auto-loaded
# valid options (case sensitive) are:
# - dillo
# - imageviewer
# - trayicon
# separate plugins with a space ("dillo trayicon")
#SYLPHEED_BROWSER="your-browser %s" # define which browser should be used to edit/view
# HTML documents. Note that %s will be substituted
# for the URL/filename
#SYLPHEED_EDITOR="your-editor %s" # define which editor should be used to compose
# new mail messages. Note that %s will be substituted
# for the filename
# Example configuration for MPlayer
#SESSION_0_TITLE="MPlayer"
#SESSION_0_TYPE=mplayer
# Optional variables
# NFS support
#MPLAYER_NFS="server:/path/to/movies"
# SMB support
#MPLAYER_SMB="//server/path/to/movies"
#MPLAYER_SMB_OPTIONS="username=mplayer,password=mplayer"
# Language MPlayer should use (defaults to 'en' if not declared)
#MPLAYER_LANG=en
# hdparm
#
# !! WARNING !! WARNING !! WARNING !! WARNING !! WARNING !!
# hdparm provides a command line interface to various hard
# disk ioctls supported by the stock Linux IDE/ST-506 device
# driver. Use this utility with CAUTION, and at YOUR OWN RISK
# as it can PERMANENTLY DAMAGE YOUR SYSTEM!! Read up on the
# manual pages for more information.
#
# MPLAYER_HDPARM="-d1 -a8 -u1 -c1"
# CD/DVD device
#MPLAYER_CD_DVD="/dev/ide/host0/bus0/target0/lun0/cd"
# Video driver (defaults to 'x11' if not declared)
#MPLAYER_DRIVER="xv"
Ich weiss, iss jetzt n riessen Ding das ich hier hinmache, aber ich
weiss mir echt nicht mehr zu helfen .
Vielleicht gibts ja doch jemanden unter euch der das mal durchschauen könnt, und mir dann meine Fehler sagen kann .
Ich hab echt keine Ahnung .
Ich denk s hängt irgendwie mit der Einstellung von XFree und den
Sessions zusammen, aber da ich mich mit Linux, bis jetzt, überhaupt so schlecht auskenne, weiss ich einfach nicht was ich falsch mache .
Jo denne,
ich setz echt grosse Hoffnung in euch,
ihr seit wie's aussieht nämlich meine letzte Hoffnung .
Mit freundlichen Grüssen
euer Jonas
