WebCam openSuse12.2 System Crash

ws1964 · 27 Okt. 2012

Hallo,

Habe einen HP dv7 Notebook und openSuse 12.2 installiert.
Starte ich die Webcam mit Skype oder einer anderen Anwendung die die Webcam benutzt friert das sytem ein.
Also keine Tastatur oder Mauseingabe mehr möglich. Nur noch Hauptschalter Aus und wieder Ein.

dann habe ich im Internet etwas von UVC-Treibern gelesen und die Anwendung GUVCView aus den Repositories installiert.
Nach dem Start ging die Maus noch und ich konnte zur Konsole wechseln, welche eingefroren war. Das war's.
Auf der Konsole waren etliche Meldungen zu lesen wie:

Code:

GUVCView
Kernel Panic
PID 3762, comm: guvcview ...
kernel panic - switch to text konsole

Mehr bekomme ich nicht raus.
Hinweis: Auf dem gleichen Rechner ist noch openSuse 12.1 installiert. Da läuft die Web Cam.

Hat jemand einen Hinweis?

spoensche · 27 Okt. 2012

Poste mal die Ausgabe von

Code:

dmesg | egrep -i "warn|err|crit|fail"

und von

Code:

lspci -v

.

ws1964 · 28 Okt. 2012

Ausgabe von dmesg:

Code:

[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.002999] Marking TSC unstable due to check_tsc_sync_source failed
[    0.085082] ACPI: Using IOAPIC for interrupt routing
[    0.219423] \_SB_.PCI0:_OSC request failed
[    0.228205] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.228348] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.228404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[    0.228461] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[    0.228542] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP6._PRT]
[    0.228599] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT]
[    0.228696] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.228832] \_SB_.PCI0:_OSC request failed
[    0.228880] \_SB_.PCI0:_OSC request failed
[    0.228886]  pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[    0.241135] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241190] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241244] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241297] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241350] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241404] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241457] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.241511] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    1.875065] ata4: softreset failed (device not ready)
[    1.876927] ata2: softreset failed (device not ready)
[    1.879525] ata1: softreset failed (device not ready)
[   14.053032] sdhci: Copyright(c) Pierre Ossman

und lspci -v

Code:

00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 0
	Capabilities: [c4] HyperTransport: Slave or Primary Interface
	Capabilities: [54] HyperTransport: UnitID Clumping
	Capabilities: [40] HyperTransport: Retry Mode
	Capabilities: [9c] HyperTransport: #1a
	Capabilities: [f8] HyperTransport: #1c

00:01.0 PCI bridge: Hewlett-Packard Company Device 9602 (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, medium devsel, latency 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00007000-00007fff
	Memory behind bridge: d2300000-d24fffff
	Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
	Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc

00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=07, sec-latency=0
	I/O behind bridge: 00003000-00006fff
	Memory behind bridge: d1300000-d22fffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000d0ffffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
	Memory behind bridge: d1200000-d12fffff
	Prefetchable memory behind bridge: 00000000d2600000-00000000d26fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
	Memory behind bridge: d1100000-d11fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d2700000-d27fffff
	Prefetchable memory behind bridge: 00000000d1000000-00000000d10fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (prog-if 01 [AHCI 1.0])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 22
	I/O ports at 8038 [size=8]
	I/O ports at 804c [size=4]
	I/O ports at 8030 [size=8]
	I/O ports at 8048 [size=4]
	I/O ports at 8010 [size=16]
	Memory at d2508000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [60] Power Management version 2
	Capabilities: [70] SATA HBA v1.0
	Kernel driver in use: ahci

00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	Memory at d2507000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:12.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	Memory at d2506000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 17
	Memory at d2508500 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd

00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
	Memory at d2505000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
	Memory at d2504000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
	Memory at d2508400 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd

00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 3a)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: 66MHz, medium devsel
	Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
	Kernel driver in use: piix4_smbus

00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller (prog-if 8a [Master SecP PriP])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	I/O ports at 01f0 [size=8]
	I/O ports at 03f4 [size=1]
	I/O ports at 0170 [size=8]
	I/O ports at 0374 [size=1]
	I/O ports at 8000 [size=16]
	Capabilities: [70] MSI: Enable- Count=1/1 Maskable- 64bit-
	Kernel driver in use: pata_atiixp

00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, slow devsel, latency 64, IRQ 16
	Memory at d2500000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: snd_hda_intel

00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive decode])
	Flags: bus master, 66MHz, medium devsel, latency 64
	Bus: primary=00, secondary=80, subordinate=8f, sec-latency=64
	I/O behind bridge: 00001000-00001fff

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration (rev 40)
	Flags: fast devsel
	Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor Address Map
	Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller
	Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control
	Flags: fast devsel
	Capabilities: [f0] Secure device <?>
	Kernel driver in use: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor Link Control
	Flags: fast devsel

01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 18
	Memory at c0000000 (32-bit, prefetchable) [size=256M]
	I/O ports at 7000 [size=256]
	Memory at d2400000 (32-bit, non-prefetchable) [size=64K]
	Memory at d2300000 (32-bit, non-prefetchable) [size=1M]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [50] Power Management version 3
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: radeon

01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS780 HDMI Audio [Radeon HD 3000-3300 Series]
	Subsystem: Advanced Micro Devices [AMD] nee ATI RS780 HDMI Audio [Radeon HD 3000-3300 Series]
	Flags: bus master, fast devsel, latency 0, IRQ 19
	Memory at d2410000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 3
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: snd_hda_intel

08:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 17
	Memory at d1200300 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at d2600000 [disabled] [size=64K]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
	Kernel driver in use: sdhci-pci

08:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (prog-if 01)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: fast devsel, IRQ 17
	Memory at d1200200 (32-bit, non-prefetchable) [size=256]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-

08:00.3 System peripheral: JMicron Technology Corp. MS Host Controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 17
	Memory at d1200100 (32-bit, non-prefetchable) [size=256]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
	Kernel driver in use: jmb38x_ms

08:00.4 System peripheral: JMicron Technology Corp. xD Host Controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 5
	Memory at d1200000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-

09:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
	Subsystem: Hewlett-Packard Company Device 1381
	Flags: bus master, fast devsel, latency 0, IRQ 18
	Memory at d1100000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] Power Management version 2
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [60] Express Legacy Endpoint, MSI 00
	Capabilities: [90] MSI-X: Enable- Count=1 Masked-
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
	Kernel driver in use: ath9k

0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 44
	I/O ports at 2000 [size=256]
	Memory at d1010000 (64-bit, prefetchable) [size=4K]
	Memory at d1000000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at d1020000 [disabled] [size=128K]
	Capabilities: [40] Power Management version 3
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Capabilities: [70] Express Endpoint, MSI 01
	Capabilities: [ac] MSI-X: Enable- Count=2 Masked-
	Capabilities: [cc] Vital Product Data
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 01-00-00-00-00-00-00-00
	Kernel driver in use: r8169

Danke fuer Deine Bemuehungen.

spoensche · 29 Okt. 2012

Code:

[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.002999] Marking TSC unstable due to check_tsc_sync_source failed
[    0.085082] ACPI: Using IOAPIC for interrupt routing
[    1.875065] ata4: softreset failed (device not ready)
[    1.876927] ata2: softreset failed (device not ready)
[    1.879525] ata1: softreset failed (device not ready)

Da stimmt etwas vorne und hinten nicht.
Boote mal mit dem Bootparameter

Code:

noioapicreroute

und poste anschließend die Ausgabe des selben Befehls.

ws1964 · 30 Okt. 2012

spoensche schrieb:
Boote mal mit dem Bootparameter

Code:

noioapicreroute

und poste anschließend die Ausgabe des selben Befehls.

Das wuerde ich gern tun aber:

Laut: http://doc.opensuse.org/documentation/html/openSUSE/opensuse-reference/grub2.html

Code:

In the graphical boot menu, select the operating system to boot with the arrow keys. If you select a Linux system, you can enter additional boot parameters at the boot prompt.

Bei mir nicht! Ich kann keinen Parameter eingeben. Ich habe nur das Menu.
Ich kann [E] druecken, da bekomme ich auf Grund des transparenten und gruen gefaerbten Hintergrundes ein edit Fenster zu sehen in dem ich fast nichts erkennen kann, aber Bootoptionen wie beim Vorgaenger von Grub2 kann ich nirgends eingeben.

Ach so, im Fall ich finde es inzwischen, dein

Code:

noioapicreroute

ist da ein dreher drin?

Code:

noioapcireroute

ist das eher OK? Also APCI

Nur zur Info...

Danke fuer Deine schnelle Antwort

josef-wien · 30 Okt. 2012

ws1964 schrieb:
ist da ein dreher drin?

Nein (wie Du auch der Dokumentation entnehmen kannst).

Informationen zu ACPI und APIC findest Du in der Wikipedia,

ws1964 schrieb:
APCI

hat nichts mit EDV zu tun.

P. S. Zu Deinem GRUB2-Problem kann ich nichts beitragen, im Notfall kannst Du den Parameter auch mit YaST fest eintragen, die beim aktuellen Boot-Vorgang verwendeten Parameter sieht Du mit:

Code:

cat /proc/cmdline

ws1964 · 30 Okt. 2012

josef-wien schrieb:
ws1964 schrieb:

ist da ein dreher drin?

Zum Vergrößern anklicken....

Nein (wie Du auch der Dokumentation entnehmen kannst).

Danke Dir für die Info und auch die Doku.

@spoensche
Auch Danke fuer Deine Antwort.
Boot parameter Eingabe gefunden. Leider ziemlich versteckt, aber gut.
Hier die Ausgaben von:
dmesg | egrep -i "warn|err|crit|fail"

Code:

[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.001999] Marking TSC unstable due to check_tsc_sync_source failed
[    0.092129] ACPI: Using IOAPIC for interrupt routing
[    0.226419] \_SB_.PCI0:_OSC request failed
[    0.235203] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.235347] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.235403] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[    0.235459] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[    0.235540] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP6._PRT]
[    0.235597] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT]
[    0.235694] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.235830] \_SB_.PCI0:_OSC request failed
[    0.235878] \_SB_.PCI0:_OSC request failed
[    0.235884]  pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[    0.248238] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248293] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248347] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248401] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248454] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248507] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248561] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.248614] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    1.398059] ata4: softreset failed (device not ready)
[    1.398122] ata2: softreset failed (device not ready)
[    1.398186] ata1: softreset failed (device not ready)
[   12.251119] microcode: failed to load file amd-ucode/microcode_amd.bin
[   12.889156] WARNING! power/level is deprecated; use power/control instead
[   13.410941] sdhci: Copyright(c) Pierre Ossman

und von lspci -v

Code:

00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 0
	Capabilities: [c4] HyperTransport: Slave or Primary Interface
	Capabilities: [54] HyperTransport: UnitID Clumping
	Capabilities: [40] HyperTransport: Retry Mode
	Capabilities: [9c] HyperTransport: #1a
	Capabilities: [f8] HyperTransport: #1c

00:01.0 PCI bridge: Hewlett-Packard Company Device 9602 (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, medium devsel, latency 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00007000-00007fff
	Memory behind bridge: d2300000-d24fffff
	Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
	Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc

00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=07, sec-latency=0
	I/O behind bridge: 00003000-00006fff
	Memory behind bridge: d1300000-d22fffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000d0ffffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
	Memory behind bridge: d1200000-d12fffff
	Prefetchable memory behind bridge: 00000000d2600000-00000000d26fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
	Memory behind bridge: d1100000-d11fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d2700000-d27fffff
	Prefetchable memory behind bridge: 00000000d1000000-00000000d10fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: Hewlett-Packard Company Device 30fc
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [110] Virtual Channel
	Kernel driver in use: pcieport

00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (prog-if 01 [AHCI 1.0])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 22
	I/O ports at 8038 [size=8]
	I/O ports at 804c [size=4]
	I/O ports at 8030 [size=8]
	I/O ports at 8048 [size=4]
	I/O ports at 8010 [size=16]
	Memory at d2508000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [60] Power Management version 2
	Capabilities: [70] SATA HBA v1.0
	Kernel driver in use: ahci

00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	Memory at d2507000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:12.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	Memory at d2506000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 17
	Memory at d2508500 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd

00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
	Memory at d2505000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
	Memory at d2504000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
	Memory at d2508400 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd

00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 3a)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: 66MHz, medium devsel
	Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
	Kernel driver in use: piix4_smbus

00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller (prog-if 8a [Master SecP PriP])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	I/O ports at 01f0 [size=8]
	I/O ports at 03f4 [size=1]
	I/O ports at 0170 [size=8]
	I/O ports at 0374 [size=1]
	I/O ports at 8000 [size=16]
	Capabilities: [70] MSI: Enable- Count=1/1 Maskable- 64bit-
	Kernel driver in use: pata_atiixp

00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, slow devsel, latency 64, IRQ 16
	Memory at d2500000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: snd_hda_intel

00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive decode])
	Flags: bus master, 66MHz, medium devsel, latency 64
	Bus: primary=00, secondary=80, subordinate=8f, sec-latency=64
	I/O behind bridge: 00001000-00001fff

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration (rev 40)
	Flags: fast devsel
	Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor Address Map
	Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller
	Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control
	Flags: fast devsel
	Capabilities: [f0] Secure device <?>
	Kernel driver in use: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 11h Processor Link Control
	Flags: fast devsel

01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 18
	Memory at c0000000 (32-bit, prefetchable) [size=256M]
	I/O ports at 7000 [size=256]
	Memory at d2400000 (32-bit, non-prefetchable) [size=64K]
	Memory at d2300000 (32-bit, non-prefetchable) [size=1M]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [50] Power Management version 3
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: radeon

01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS780 HDMI Audio [Radeon HD 3000-3300 Series]
	Subsystem: Advanced Micro Devices [AMD] nee ATI RS780 HDMI Audio [Radeon HD 3000-3300 Series]
	Flags: bus master, fast devsel, latency 0, IRQ 19
	Memory at d2410000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 3
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: snd_hda_intel

08:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 17
	Memory at d1200300 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at d2600000 [disabled] [size=64K]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
	Kernel driver in use: sdhci-pci

08:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (prog-if 01)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: fast devsel, IRQ 17
	Memory at d1200200 (32-bit, non-prefetchable) [size=256]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-

08:00.3 System peripheral: JMicron Technology Corp. MS Host Controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 17
	Memory at d1200100 (32-bit, non-prefetchable) [size=256]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
	Kernel driver in use: jmb38x_ms

08:00.4 System peripheral: JMicron Technology Corp. xD Host Controller
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 5
	Memory at d1200000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [a4] Power Management version 3
	Capabilities: [80] Express Endpoint, MSI 00
	Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-

09:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
	Subsystem: Hewlett-Packard Company Device 1381
	Flags: bus master, fast devsel, latency 0, IRQ 18
	Memory at d1100000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] Power Management version 2
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [60] Express Legacy Endpoint, MSI 00
	Capabilities: [90] MSI-X: Enable- Count=1 Masked-
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
	Kernel driver in use: ath9k

0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
	Subsystem: Hewlett-Packard Company Device 30fc
	Flags: bus master, fast devsel, latency 0, IRQ 44
	I/O ports at 2000 [size=256]
	Memory at d1010000 (64-bit, prefetchable) [size=4K]
	Memory at d1000000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at d1020000 [disabled] [size=128K]
	Capabilities: [40] Power Management version 3
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Capabilities: [70] Express Endpoint, MSI 01
	Capabilities: [ac] MSI-X: Enable- Count=2 Masked-
	Capabilities: [cc] Vital Product Data
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 01-00-00-00-00-00-00-00
	Kernel driver in use: r8169

Hoffe das hilft zur Diagnose des Patienten.
Danke nochmals.

josef-wien · 30 Okt. 2012

Zum softreset (der harmlos sein könnte) bitte noch:

Code:

dmesg | egrep "ata[0-4]|line:"

spoensche · 30 Okt. 2012

Code:

ata4: softreset failed (device not ready)
[    1.398122] ata2: softreset failed (device not ready)
[    1.398186] ata1: softreset failed (device not ready)
[   12.251119] microcode: failed to load file amd-ucode/microcode_amd.bin

beunruhigt mich etwas.

Deine Festolatte und DVD- Laufwerk funktionieren ordnungsgemäß? Installier mal das Paket microcode_ctl. Tritt die microcode Meldung danach immer noch auf?

josef-wien · 31 Okt. 2012

ws1964 schrieb:
Boot parameter Eingabe gefunden. Leider ziemlich versteckt, aber gut.

Falls es noch niemand getan hat, stell bitte Dein Wissen bei diesem Thema zur Verfügung.

muck19 · 31 Okt. 2012

ws1964 schrieb:
Ich kann [E] druecken, da bekomme ich auf Grund des transparenten und gruen gefaerbten Hintergrundes ein edit Fenster zu sehen in dem ich fast nichts erkennen kann,

Yast - Bootloader - Optionen - use graphical console <- Haken wegnehmen. Neu booten. (manchmal muss man 2x booten bis das greift)
Jetzt sieht das gleich ganz anders aus :roll:

Gruss
Michael

ws1964 · 31 Okt. 2012

josef-wien schrieb:
ws1964 schrieb:

Boot parameter Eingabe gefunden. Leider ziemlich versteckt, aber gut.

Zum Vergrößern anklicken....

Falls es noch niemand getan hat, stell bitte Dein Wissen bei diesem Thema zur Verfügung.

Hallo Josef,

Hier im Forum gibt es diesen Hinweis:
http://www.linux-club.de/viewtopic.php?f=4&t=116584&p=735092&hilit=bootoptionen+Grub2#p735092
unter dem ich die genaue Anleitung fand.

ws1964 · 31 Okt. 2012

spoensche schrieb:
Code:

ata4: softreset failed (device not ready) [ 1.398122] ata2: softreset failed (device not ready) [ 1.398186] ata1: softreset failed (device not ready) [ 12.251119] microcode: failed to load file amd-ucode/microcode_amd.bin

beunruhigt mich etwas.

Deine Festolatte und DVD- Laufwerk funktionieren ordnungsgemäß? Installier mal das Paket microcode_ctl. Tritt die microcode Meldung danach immer noch auf?

Zu Frage 1) Ja alles funktioniert vom Feinsten.
Zu Frage 2) Paket ist bereits installiert. Somit tritt die Fehlermeldung also auch mit installiertem microcode_ctl auf.

Frage Meinerseits.
Wo liegt der gravierende Unterschied zwischen openSuse 12.1 und 12.2?
Denn auf diesem Rechner existiert noch openSuse 12.1. und da läuft die web-cam. Wo haben die openSuse-ler denn da herum-geschraubt?

spoensche · 31 Okt. 2012

Die Ursache für die Systemfreezer bei Verwendung der Webcam könnte mit dem Problem https://bugzilla.novell.com/show_bug.cgi?id=780088aahttps://bugzilla.novell.com/show_bug.cgi?id=780088aa zusammenhängen, muss aber nicht.

Du solltest den dortigen Workaround, Bootparam nomodeset und verwendung des FGLRX Treibers mal ausprobieren. Vorher postest du bitte aber noch die Ausgaben folgender Befehle:

Code:

dmesg | grep -i ata
hwinfo --cpu
hwinfo --gfxcard

ws1964 · 1 Nov. 2012

spoensche schrieb:
Die Ursache für die Systemfreezer bei Verwendung der Webcam könnte mit dem Problem https://bugzilla.novell.com/show_bug.cgi?id=780088aahttps://bugzilla.novell.com/show_bug.cgi?id=780088aa zusammenhängen, muss aber nicht.

Du solltest den dortigen Workaround, Bootparam nomodeset und verwendung des FGLRX Treibers mal ausprobieren. Vorher postest du bitte aber noch die Ausgaben folgender Befehle:

Code:

dmesg | grep -i ata hwinfo --cpu hwinfo --gfxcard

Hallo,

Also erst einmal Danke fuer Deinen Einsatz.
Den Link habe ich schon mal angeklickt, kommt aber:

Code:

780088aahttps://bugzilla.novell.com/show_bug.cgi?id=780088aa' is not a valid bug number nor an alias to a bug.

Please press Back and try again.

OK, aber hier die postings, die Du angeregt hast:

1.) dmesg | grep -i ata

Code:

[    0.000000]  BIOS-e820: 00000000afeec000 - 00000000afeff000 (ACPI data)
[    0.000000]   NODE_DATA [0000000033400000 - 0000000033401fff] (remapped)
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.4.6-2.10-desktop root=UUID=80ee9dfd-aff9-4980-a1ab-f0be0e263763 video=1440x900 resume=/dev/disk/by-id/ata-ST9500325AS_5VE2V1Z5-part1 splash=silent quiet showopts
[    0.000000] Memory: 3805696k/5242880k available (5129k kernel code, 81176k reserved, 3693k data, 496k init, 2984164k highmem)
[    0.000000]       .data : 0xc0702762 - 0xc0a9de40   (3693 kB)
[    0.222474] ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62
[    0.223388] _OSC request data:1 8 1f 
[    0.232832] _OSC request data:1 1f 1f 
[    0.232880] _OSC request data:1 0 1d 
[    0.245997] libata version 3.00 loaded.
[    0.932148] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[    0.934531] ata1: SATA max UDMA/133 abar m1024@0xd2508000 port 0xd2508100 irq 22
[    0.934535] ata2: SATA max UDMA/133 abar m1024@0xd2508000 port 0xd2508180 irq 22
[    0.934539] ata3: SATA max UDMA/133 abar m1024@0xd2508000 port 0xd2508200 irq 22
[    0.934543] ata4: SATA max UDMA/133 abar m1024@0xd2508000 port 0xd2508280 irq 22
[    0.934547] ata5: SATA max UDMA/133 abar m1024@0xd2508000 port 0xd2508300 irq 22
[    0.934551] ata6: SATA max UDMA/133 abar m1024@0xd2508000 port 0xd2508380 irq 22
[    1.204381] PM: Checking hibernation image partition /dev/disk/by-id/ata-ST9500325AS_5VE2V1Z5-part1
[    1.241101] ata3: SATA link down (SStatus 0 SControl 300)
[    1.244359] ata6: SATA link down (SStatus 0 SControl 300)
[    1.244424] ata5: SATA link down (SStatus 0 SControl 300)
[    1.400065] ata1: softreset failed (device not ready)
[    1.400111] ata1: applying PMP SRST workaround and retrying
[    1.400129] ata2: softreset failed (device not ready)
[    1.400176] ata2: applying PMP SRST workaround and retrying
[    1.402066] ata4: softreset failed (device not ready)
[    1.402111] ata4: applying PMP SRST workaround and retrying
[    1.555073] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.555102] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.556217] ata1.00: ATA-8: ST9500325AS, 0003HPM1, max UDMA/100
[    1.556220] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.557061] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.557577] ata1.00: configured for UDMA/100
[    1.557817] scsi 0:0:0:0: Direct-Access     ATA      ST9500325AS      0003 PQ: 0 ANSI: 5
[    1.560704] ata4.00: ATAPI: hp      DVDRAM GT31L, MR52, max UDMA/100
[    1.564767] ata4.00: configured for UDMA/100
[    1.602244] ata2.00: ATA-8: WDC WD10JPVT-00A1YT0, 01.01A01, max UDMA/133
[    1.602247] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.603642] ata2.00: configured for UDMA/133
[    1.603790] scsi 1:0:0:0: Direct-Access     ATA      WDC WD10JPVT-00A 01.0 PQ: 0 ANSI: 5
[    2.772130] Write protecting the kernel read-only data: 3340k
[    2.772133] NX-protecting the kernel data: 5108k
[    2.819418] pata_atiixp 0000:00:14.1: setting latency timer to 64
[    2.819764] scsi6 : pata_atiixp
[    2.819922] scsi7 : pata_atiixp
[    2.820715] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8000 irq 14
[    2.820718] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8008 irq 15
[    6.429690] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: acl,user_xattr
[   18.216513] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)

2.) hwinfo --cpu

Code:

01: None 00.0: 10103 CPU
  [Created at cpu.374]
  Unique ID: rdCR.j8NaKXDZtZ6
  Hardware Class: cpu
  Arch: Intel
  Vendor: "AuthenticAMD"
  Model: 17.3.1 "AMD Turion(tm) X2 Ultra Dual-Core Mobile ZM-82"
  Features: fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,mmx,fxsr,sse,sse2,ht,syscall,nx,mmxext,fxsr_opt,rdtscp,lm,3dnowext,3dnow,constant_tsc,nonstop_tsc,extd_apicid,pni,cx16,lahf_lm,cmp_legacy,svm,extapic,cr8_legacy,3dnowprefetch,osvw,skinit,hw_pstate,lbrv,svm_lock,nrip_save
  Clock: 2200 MHz
  BogoMips: 4400.24
  Cache: 1024 kb
  Units/Processor: 2
  Config Status: cfg=no, avail=yes, need=no, active=unknown

02: None 01.0: 10103 CPU
  [Created at cpu.374]
  Unique ID: wkFv.j8NaKXDZtZ6
  Hardware Class: cpu
  Arch: Intel
  Vendor: "AuthenticAMD"
  Model: 17.3.1 "AMD Turion(tm) X2 Ultra Dual-Core Mobile ZM-82"
  Features: fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,mmx,fxsr,sse,sse2,ht,syscall,nx,mmxext,fxsr_opt,rdtscp,lm,3dnowext,3dnow,constant_tsc,nonstop_tsc,extd_apicid,pni,cx16,lahf_lm,cmp_legacy,svm,extapic,cr8_legacy,3dnowprefetch,osvw,skinit,hw_pstate,lbrv,svm_lock,nrip_save
  Clock: 2200 MHz
  BogoMips: 4400.24
  Cache: 1024 kb
  Units/Processor: 2
  Config Status: cfg=no, avail=yes, need=no, active=unknown

3.) hwinfo --gfxcard

Code:

31: PCI 105.0: 0300 VGA compatible controller (VGA)
  [Created at pci.319]
  Unique ID: ul7N.fqdkMh7f9M7
  Parent ID: vSkL.QA_hbVWU301
  SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:05.0
  SysFS BusID: 0000:01:05.0
  Hardware Class: graphics card
  Model: "ATI Radeon HD 3200 Graphics"
  Vendor: pci 0x1002 "ATI Technologies Inc"
  Device: pci 0x9612 "ATI Radeon HD 3200 Graphics"
  SubVendor: pci 0x103c "Hewlett-Packard Company"
  SubDevice: pci 0x30fc 
  Driver: "radeon"
  Driver Modules: "drm"
  Memory Range: 0xc0000000-0xcfffffff (ro,non-prefetchable)
  I/O Ports: 0x7000-0x7fff (rw)
  Memory Range: 0xd2400000-0xd240ffff (rw,non-prefetchable)
  Memory Range: 0xd2300000-0xd23fffff (rw,non-prefetchable)
  IRQ: 18 (268551 events)
  I/O Ports: 0x3c0-0x3df (rw)
  Module Alias: "pci:v00001002d00009612sv0000103Csd000030FCbc03sc00i00"
  Driver Info #0:
    XFree86 v4 Server Module: radeonhd
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #9 (PCI bridge)

Primary display adapter: #31

tomm.fa · 1 Nov. 2012

ws1964 schrieb:
Den Link habe ich schon mal angeklickt, kommt aber:

Code:

780088aahttps://bugzilla.novell.com/show_bug.cgi?id=780088aa' is not a valid bug number nor an alias to a bug. Please press Back and try again.

Geht es eventuell um diesen Link: https://bugzilla.novell.com/show_bug.cgi?id=780088?

josef-wien · 1 Nov. 2012

ws1964 schrieb:

Code:

[    1.400065] ata1: softreset failed (device not ready)
[    1.400111] ata1: applying PMP SRST workaround and retrying
[    1.400129] ata2: softreset failed (device not ready)
[    1.400176] ata2: applying PMP SRST workaround and retrying
[    1.402066] ata4: softreset failed (device not ready)
[    1.402111] ata4: applying PMP SRST workaround and retrying

Gemäß

drivers/ata/libahci.c schrieb:
* Soft reset fails with IPMS set when PMP is enabled but
* SATA HDD/ODD is connected to SATA port, do soft reset
* again to port 0.

paßt das, da nach dem workaround

ws1964 schrieb:

Code:

[    1.555073] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.555102] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.557061] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

kommt.

spoensche schrieb:
verwendung des FGLRX Treibers mal ausprobieren

Die letzte Deine Grafikkarte unterstützende fglrx-Version ist 12.6. Falls wirklich radeon vom Kernel 3.4 das Problem sein sollte, würde ich vor dem Versuch mit fglrx zusätzlich den aktuellen Kernel 3.6 von http://download.opensuse.org/repositories/Kernel:/stable/standard/ oder http://download.opensuse.org/repositories/openSUSE:/Tumbleweed/standard/ installieren und schauen, ob das Problem weiterhin besteht.

P. S. Kommt bei

Code:

rpm -V microcode_ctl

etwas heraus?

comer352l · 5 Nov. 2012

Hi,

ich nehme mal an, das es sich um eine UVC-webcam handelt ?
Welche Kernel-Version hast du laufen ? Aktuell (openSUSE) ist 3.4.11, falls du noch eine ältere Version hast, bitte per YaST updaten !
In kernel 3.4.11 wurde ein Bug im UVC-System behoben, dessen Auswirkungen zu deiner Schilderung passt:

commit 190d60406f1e111bd212e271076bdab9e104ebe6
Author: Jayakrishnan Memana <jayakrishnan.memana@maxim-ic.com>
Date: Sun Jul 15 10:54:03 2012 -0300

uvcvideo: Reset the bytesused field when recycling an erroneous buffer

commit 8a3f0ede2b3f5477122060af1a816c6bbf09fcd2 upstream.

Buffers marked as erroneous are recycled immediately by the driver if
the nodrop module parameter isn't set. The buffer payload size is reset
to 0, but the buffer bytesused field isn't. This results in the buffer
being immediately considered as complete, leading to an infinite loop in
interrupt context.

Fix the problem by resetting the bytesused field when recycling the
buffer.

Signed-off-by: Jayakrishnan Memana <jayakrishnan.memana@maxim-ic.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ws1964 · 12 Nov. 2012

comer352l schrieb:
Hi,

ich nehme mal an, das es sich um eine UVC-webcam handelt ?

Keine Ahnung....

Meine Kernel Version ist:

Code:

Linux linux-3bfa.site 3.4.11-2.16-desktop #1 SMP PREEMPT Wed Sep 26 17:05:00 UTC 2012 (259fc87) i686 athlon i386 GNU/Linux

Aber...
Ich habe heute am 12.11.2012 (Einen Tag nach Karneval...

)
Ein update laufen lassen und... die Camera funktioniert. Erst einmal....

Das Problem: Brennen einer DVD habe ich erst jetzt entdeckt.Geht nicht. Ist keine exakte Fehler-Beschreibung. Ich Weiss.... Aber ich sehe Fortschritte.

Somit brennei ch DVD's mit openSuse 12.1 und den Rest kann ich nun mit openSuse 12.2 tun.

Es gibt immer eine Loesung.

Danke fuer Eure Hilfe!

WebCam openSuse12.2 System Crash

ws1964

Hacker

spoensche

Moderator

ws1964

Hacker

spoensche

Moderator

ws1964

Hacker

josef-wien

Ultimate Guru

ws1964

Hacker

josef-wien

Ultimate Guru

spoensche

Moderator

josef-wien

Ultimate Guru

muck19

Hacker

ws1964

Hacker

ws1964

Hacker

spoensche

Moderator

ws1964

Hacker

tomm.fa

Administrator

josef-wien

Ultimate Guru

comer352l

Newbie

ws1964

Hacker