• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

Einrichten von Sensors

JMKio

Newbie
Hallo zusammen,

ich wollte das Sensors einrichten um damit Temperatur Lüfter und andere Werte von der Hauptplatine angezeigt zu bekommen.
die Pakete sind dafür über yast installiert auf Suse 12.1.

habe ein ASUS M3a32-mvp deluxe Hauptplatine und eine ATI Radeon HD 3870 Grafikkarte

in der konsole mit su rechten
sensors-detect ausgeführt

sensors-detect
# sensors-detect revision 5984 (2011-07-10 21:22:53 +0200)
# Board: ASUSTeK Computer INC. M3A32-MVP DELUXE

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no):
WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
AMD Family 12h and 14h thermal sensors... No
AMD Family 15h thermal sensors... No
AMD Family 15h power sensors... No
Intel digital thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no):
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8716F Super IO Sensors' Success!
(address 0xe80, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no):
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO):

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no):
Using driver `i2c-piix4' for device 0000:00:14.0: ATI Technologies Inc SB600/SB700/SB800 SMBus
WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
Module i2c-dev loaded successfully.

Next adapter: Radeon i2c bit bus 0x90 (i2c-0)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)

Next adapter: Radeon i2c bit bus 0x91 (i2c-1)
Do you want to scan it? (YES/no/selectively):

Next adapter: Radeon i2c bit bus 0x92 (i2c-2)
Do you want to scan it? (YES/no/selectively):

Next adapter: Radeon i2c bit bus 0x93 (i2c-3)
Do you want to scan it? (YES/no/selectively):

Next adapter: Radeon i2c bit bus 0x14 (i2c-4)
Do you want to scan it? (YES/no/selectively):

Next adapter: SMBus PIIX4 adapter at 0b00 (i2c-5)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'... No
Client found at address 0x51
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `it87':
* ISA bus, address 0xe80
Chip `ITE IT8716F Super IO Sensors' (confidence: 9)

Do you want to overwrite /etc/sysconfig/lm_sensors? (YES/no):
Copy prog/init/lm_sensors.service to /lib/systemd/system
and run 'systemctl enable lm_sensors.service'
for initialization at boot time.
Unloading i2c-dev... OK
Unloading cpuid... OK

nur es wird nichts angezeigt.

muß ich noch irgendwas machen.

nur die radeon grafikarte mit der temperatur wird angezeigt und die festplatten temperatur.
leider wird die festplatte nicht in dem Programm ksensors nicht mit eingebunden.

was muß ich machen damit dies funktioniert?

Helft mir bitte weiter.

vielen herzlichen Dank

alles liebe

JMKio
 

tux93

Newbie
Hast du lm_sensors neu gestartet und das ausgeführt:
JMKio schrieb:
Copy prog/init/lm_sensors.service to /lib/systemd/system
and run 'systemctl enable lm_sensors.service'
for initialization at boot time.
?
 
OP
J

JMKio

Newbie
nein.
ich bin davon ausgegangen das es damit ausgeführt wurde einem damit gesagt wurde was es gemacht hat.
aber ich habe geschaut und das verzeichnis nicht gefunden prog/init/lm_sensors.service, genauso auch nicht /lib/systemd/system das es dort dieses lm_sensors.service hat.

wie dann?
 

tux93

Newbie
lm_sensors neustarten:
Code:
systemctl restart lm_sensors.service
lm_sensors mit YaST zum automatischen Start beim Systemstart festlegen:
YaST -> System -> Systemdienste -> lm_sensors -> Aktivieren -> OK
 
OP
J

JMKio

Newbie
nach dem ich dieses gemacht habe, hatte ich alle werte in ksensors angezeigt bekommen. von der grafikkarte und der hauptplatine.
nach einem neustart war die grafikkarte weg
und in dem ksensor wird die festplatte nicht angezeigt wie bei gkrellm über hddtemp.

was muß ich jetzt machen?
 

tux93

Newbie
Das verschwinden der Grafik-Temperatur kenne ich, habe aber auch noch keine Lösung/Ursache gefunden,
und da ich nur gkrellm und nicht ksensors nutze kann ich dir bei der fehlenden hddtemp-Anzeige leider auch nicht helfen,
aber da findet sich bestimmt auch noch jemand ;)

LG
 
OP
J

JMKio

Newbie
habe gerade gemerkt nach dem ich den suse ati radeon grafikkarten treiber wiede rbenutze und nicht mehr den von ati den properierten zeigt er auch wieder die temperatur von der grafikkarte mit an

einzig was fehlt ist die hdd temperatur in ksensors.

was mich nur etwas stutzig macht sind drei temperaturen von der hauptplatine. eine für cpu und einer für die ? und der ander ?
 
OP
J

JMKio

Newbie
sensors
radeon-pci-0100
Adapter: PCI adapter
temp1: +44.0°C

it8716-isa-0e80
Adapter: ISA adapter
in0: +1.20 V (min = +0.00 V, max = +4.08 V)
in1: +3.30 V (min = +0.00 V, max = +4.08 V)
in2: +0.00 V (min = +0.00 V, max = +4.08 V)
+5V: +3.02 V (min = +0.00 V, max = +4.08 V)
in4: +3.07 V (min = +0.00 V, max = +4.08 V)
in5: +0.00 V (min = +0.00 V, max = +4.08 V)
in6: +0.00 V (min = +0.00 V, max = +4.08 V)
in7: +4.08 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.25 V
fan1: 1923 RPM (min = 0 RPM)
fan2: 961 RPM (min = 0 RPM)
fan4: 1523 RPM (min = 0 RPM)
fan5: 613 RPM (min = 0 RPM)
temp1: +39.0°C (low = -1.0°C, high = +127.0°C) sensor = thermistor
temp2: +35.0°C (low = -1.0°C, high = +127.0°C) sensor = thermistor
temp3: +40.0°C (low = -1.0°C, high = +127.0°C) sensor = thermistor
cpu0_vid: +1.550 V
intrusion0: OK
 

josef-wien

Ultimate Guru
/etc/sensors.conf schrieb:
chip "it8716-*"
...
# The CPU sensor can be any of temp1, temp2 or temp3 - it's motherboard
# dependent. Same for the motherboard temperature.
Schau im Handbuch bzw. im BIOS unter "Hardware Monitor" nach, ob Du daraus klüger wirst. Ansonsten wirst Du ASUS fragen müssen.

P. S. http://www.linux-club.de/viewtopic.php?f=3&t=105750
 

TomcatMJ

Guru
Einer der gesuchten Sensoren dürfte der in der CPU selbst sein, einer der Sensor der unter(!) der CPU auf dem Board selbst sitzt und einer der fürs Systemboard, der afair in der southbridge sitzen dürfte. Welcher davon nun genau wel.cher Sensor ist dürfte wohl nur anhand einer etwas längeren Temperaturänderungsbeobachtung unter Last geschätzt werden oder durch anfrage beim Boardhersteller geklärt werden können.

Bis denne,
Tom
 
Oben