Hallo
Was muss in faxaddmodem oder wo auch immer eingestellt werden, das man mehrere Faxe ( Seiten ) auf einmal versenden kann ?
Hintergrund :
Wenn ich eine Datei Kwrite oder Andere mit mehreren Seiten über KDE Druckeraufträge versende, kommt nur eine Seite an.
Die Datei wird korrekt in eine PDF Datei umgewandelt und auf den ankommenden Fax steht zum Beispiel 1-36 .
Irgend wo habe ich mal gelesen ( wenn ich mich nicht täusche ) das man in Versenden 1 Blatt bei faxaddmodem eintragen soll was ich auch Damals gemacht habe.
Leider finde ich die Einstellung nicht mehr.
Hier meine Einstellung in/var/spool/hylafax/etc/config.ttyS0 :
# $Id: topic,v 1.4 2003/07/25 16:23:26 lhoward Exp $
#
# prototype config for Topic modems and other similarly broken firmwares
#
#
CountryCode: 49
AreaCode: xxx
FAXNumber: +xx.xxx.xxxxxx
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Johannes Hierl"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Absender %%l|%c|Seite %%P von %%T"
MaxRecvPages: 25
LockDataCalls: yes
LockVoiceCalls: yes
#
ModemType: Class1 # use this to supply a hint
# as of v1.20, +FTS is not supported, which will cause "Stop and wait"
# failures unless we use software pauses instead...
Class1PPMWaitCmd: "<delay\0727>" # \072 == : to avoid awk problem
Class1TCFWaitCmd: "<delay\0727>"
Class1EOPWaitCmd: "<delay\0729>"
Class1SwitchingCmd: "<delay\0727>" # assumption: +FRS not supported
für Hilfe Danke
Hannes
Was muss in faxaddmodem oder wo auch immer eingestellt werden, das man mehrere Faxe ( Seiten ) auf einmal versenden kann ?
Hintergrund :
Wenn ich eine Datei Kwrite oder Andere mit mehreren Seiten über KDE Druckeraufträge versende, kommt nur eine Seite an.
Die Datei wird korrekt in eine PDF Datei umgewandelt und auf den ankommenden Fax steht zum Beispiel 1-36 .
Irgend wo habe ich mal gelesen ( wenn ich mich nicht täusche ) das man in Versenden 1 Blatt bei faxaddmodem eintragen soll was ich auch Damals gemacht habe.
Leider finde ich die Einstellung nicht mehr.
Hier meine Einstellung in/var/spool/hylafax/etc/config.ttyS0 :
# $Id: topic,v 1.4 2003/07/25 16:23:26 lhoward Exp $
#
# prototype config for Topic modems and other similarly broken firmwares
#
#
CountryCode: 49
AreaCode: xxx
FAXNumber: +xx.xxx.xxxxxx
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Johannes Hierl"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Absender %%l|%c|Seite %%P von %%T"
MaxRecvPages: 25
LockDataCalls: yes
LockVoiceCalls: yes
#
ModemType: Class1 # use this to supply a hint
# as of v1.20, +FTS is not supported, which will cause "Stop and wait"
# failures unless we use software pauses instead...
Class1PPMWaitCmd: "<delay\0727>" # \072 == : to avoid awk problem
Class1TCFWaitCmd: "<delay\0727>"
Class1EOPWaitCmd: "<delay\0729>"
Class1SwitchingCmd: "<delay\0727>" # assumption: +FRS not supported
für Hilfe Danke
Hannes