Hallo,
seit Suse 10.3 (vorher 10.2) habe ich ein Problem beim booten. Es wird ein Laufwerk sdb angezeigt und beim Zugriff darauf hagelt es Fehlermeldungen (siehe Auszug aus /var/log/boot.msg). Ich habe aber nur eine SATA Platte (sda) und einen ATA Brenner (sr0) im System. Unter /sys/block/sdb/device/model steht "Config Disk".
Was ist das? Wie werde ich es wieder los?
Gruß
Michael
Core2Duo
2GB RAM
ASUS P5W-DH (Intel 975 Chipsatz)
Seagate SATA Platte am Intel ICH7R
DVD Brenner auch am ICH7R
seit Suse 10.3 (vorher 10.2) habe ich ein Problem beim booten. Es wird ein Laufwerk sdb angezeigt und beim Zugriff darauf hagelt es Fehlermeldungen (siehe Auszug aus /var/log/boot.msg). Ich habe aber nur eine SATA Platte (sda) und einen ATA Brenner (sr0) im System. Unter /sys/block/sdb/device/model steht "Config Disk".
Was ist das? Wie werde ich es wieder los?
Gruß
Michael
Core2Duo
2GB RAM
ASUS P5W-DH (Intel 975 Chipsatz)
Seagate SATA Platte am Intel ICH7R
DVD Brenner auch am ICH7R
Code:
<6>scsi0 : ata_piix
<6>scsi1 : ata_piix
<6>ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001ffa0 irq 14
<6>ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001ffa8 irq 15
<6>ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-H10N, JJ11, max UDMA/66
<6>ata1.00: configured for UDMA/66
<5>scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H10N JJ11 PQ: 0 ANSI: 5
<6>ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
<6>ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>scsi2 : ata_piix
<6>scsi3 : ata_piix
<6>ata3: SATA max UDMA/133 cmd 0x000000000001e400 ctl 0x000000000001e082 bmdma 0x000000000001d880 irq 23
<6>ata4: SATA max UDMA/133 cmd 0x000000000001e000 ctl 0x000000000001dc02 bmdma 0x000000000001d888 irq 23
<6>ata3.00: HPA unlocked: 625140335 -> 625142448, native 625142448
<6>ata3.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
<6>ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
<6>ata3.00: configured for UDMA/133
<6>ata4.00: ATA-6: Config Disk, RGL10364, max UDMA/133
<6>ata4.00: 640 sectors, multi 1: LBA
<4>ata4.00: Drive reports diagnostics failure. This may indicate a drive
<4>ata4.00: fault or invalid emulation. Contact drive vendor for information.
<4>ata4.00: device is on DMA blacklist, disabling DMA
<6>ata4.00: configured for PIO4
<5>scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
<5>scsi 3:0:0:0: Direct-Access ATA Config Disk RGL1 PQ: 0 ANSI: 5
<6>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>USB Universal Host Controller Interface driver v3.0
<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
<7>PCI: Setting latency timer of device 0000:00:1d.0 to 64
<6>uhci_hcd 0000:00:1d.0: UHCI Host Controller
<5>sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 2:0:0:0: [sda] Write Protect is off
<7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 2:0:0:0: [sda] Write Protect is off
<7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1 sda2 < sda5 sda6<6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
<4> sda7<6>uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
<6>usb usb1: new device found, idVendor=0000, idProduct=0000
<4> sda8<6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<4> sda9<6>usb usb1: Product: UHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<4> sda10 >
<6>usb usb1: SerialNumber: 0000:00:1d.0
<5>sd 2:0:0:0: [sda] Attached SCSI disk
<5>sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
<5>sd 3:0:0:0: [sdb] Write Protect is off
<7>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
<5>sd 3:0:0:0: [sdb] Write Protect is off
<7>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
<6> sdb:<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
<7>PCI: Setting latency timer of device 0000:00:1d.1 to 64
<6>uhci_hcd 0000:00:1d.1: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
<6>uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
<6>usb usb2: new device found, idVendor=0000, idProduct=0000
<6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: UHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<6>usb usb2: SerialNumber: 0000:00:1d.1
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
<7>PCI: Setting latency timer of device 0000:00:1d.2 to 64
<6>uhci_hcd 0000:00:1d.2: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
<6>uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
<6>usb 1-2: new low speed USB device using uhci_hcd and address 2
<6>usb usb3: new device found, idVendor=0000, idProduct=0000
<6>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: UHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<6>usb usb3: SerialNumber: 0000:00:1d.2
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>usb 1-2: new device found, idVendor=046d, idProduct=c046
<6>usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2: Product: USB Optical Mouse
<6>usb 1-2: Manufacturer: Logitech
<6>usb 1-2: configuration #1 chosen from 1 choice
<6>ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
<7>PCI: Setting latency timer of device 0000:00:1d.3 to 64
<6>uhci_hcd 0000:00:1d.3: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
<6>uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ec00
<6>usb usb4: new device found, idVendor=0000, idProduct=0000
<6>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb4: Product: UHCI Host Controller
<6>usb usb4: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<6>usb usb4: SerialNumber: 0000:00:1d.3
<6>usb usb4: configuration #1 chosen from 1 choice
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
<6>usb 3-2: new full speed USB device using uhci_hcd and address 2
<7>PCI: Setting latency timer of device 0000:00:1d.7 to 64
<6>ehci_hcd 0000:00:1d.7: EHCI Host Controller
<6>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
<6>ehci_hcd 0000:00:1d.7: debug port 1
<7>PCI: cache line size of 32 is not supported by device 0000:00:1d.7
<6>ehci_hcd 0000:00:1d.7: irq 20, io mem 0xffafbc00
<6>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb5: new device found, idVendor=0000, idProduct=0000
<6>usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb5: Product: EHCI Host Controller
<6>usb usb5: Manufacturer: Linux 2.6.22.9-0.4-default ehci_hcd
<6>usb usb5: SerialNumber: 0000:00:1d.7
<6>usb usb5: configuration #1 chosen from 1 choice
<6>hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 8 ports detected
<6>usb 5-7: new high speed USB device using ehci_hcd and address 4
<6>usb 5-7: new device found, idVendor=05e3, idProduct=0606
<6>usb 5-7: new device strings: Mfr=0, Product=1, SerialNumber=0
<6>usb 5-7: Product: USB2.0 Hub
<6>usb 5-7: configuration #1 chosen from 1 choice
<6>hub 5-7:1.0: USB hub found
<6>hub 5-7:1.0: 4 ports detected
<6>usb 1-2: USB disconnect, address 2
<6>usbcore: registered new interface driver hiddev
<6>usb 1-2: new low speed USB device using uhci_hcd and address 3
<6>usb 1-2: new device found, idVendor=046d, idProduct=c046
<6>usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2: Product: USB Optical Mouse
<6>usb 1-2: Manufacturer: Logitech
<6>usb 1-2: configuration #1 chosen from 1 choice
<6>usb 3-2: new full speed USB device using uhci_hcd and address 3
<6>usb 3-2: new device found, idVendor=067b, idProduct=2305
<6>usb 3-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 3-2: Product: IEEE-1284 Controller
<6>usb 3-2: Manufacturer: Prolific Technology Inc.
<6>usb 3-2: configuration #1 chosen from 1 choice
<6>input: Logitech USB Optical Mouse as /class/input/input2
<6>input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-2
<6>usbcore: registered new interface driver usbhid
<6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<3>ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata4.00: cmd c4/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
<4> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
<6>ata4: soft resetting link
<4>ata4: port is slow to respond, please be patient (Status 0xd0)
<3>ata4: SRST failed (errno=-16)
<6>ata4: soft resetting link
<4>ata4: port is slow to respond, please be patient (Status 0xd0)
<3>ata4: SRST failed (errno=-16)
<6>ata4: soft resetting link
<4>ata4: port is slow to respond, please be patient (Status 0xd0)
<3>ata4: SRST failed (errno=-16)
<6>ata4: soft resetting link
<3>ata4: SRST failed (errno=-16)
<3>ata4: reset failed, giving up
<4>ata4.00: disabled
<6>ata4: EH complete
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<2>ldm_validate_partition_table(): Disk read failed.
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 24
<3>Buffer I/O error on device sdb, logical block 3
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 24
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<4> unable to read partition table
<5>sd 3:0:0:0: [sdb] Attached SCSI disk
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<4>Attempting manual resume
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda7, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>Floppy drive(s): fd0 is 1.44M
<5>scsi 0:0:0:0: Attached scsi generic sg0 type 5
<5>sd 2:0:0:0: Attached scsi generic sg1 type 0
<6>FDC 0 is a post-1991 82077
<5>sd 3:0:0:0: Attached scsi generic sg2 type 0
<3>intel_rng: FWH not detected
<6>ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 19
<7>PCI: Setting latency timer of device 0000:03:00.0 to 64
<6>sky2 0000:03:00.0: v1.14 addr 0xff8fc000 irq 19 Yukon-EC (0xb6) rev 2
<6>sky2 eth0: addr 00:18:f3:93:d3:ab
<6>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:02:00.0 to 64
<6>sky2 0000:02:00.0: v1.14 addr 0xff7fc000 irq 16 Yukon-EC (0xb6) rev 2
<6>sky2 eth1: addr 00:18:f3:93:be:fb
<6>ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
<7>PCI: Setting latency timer of device 0000:00:1b.0 to 64
<4>sr0: scsi3-mmc drive: 102x/102x writer dvd-ram cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<7>sr 0:0:0:0: Attached scsi CD-ROM sr0
<6>iTCO_vendor_support: vendor-support=0
<6>rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
<4>rtc_cmos: probe of 00:03 failed with error -16
<6>input: Power Button (FF) as /class/input/input3
<6>ACPI: Power Button (FF) [PWRF]
<6>input: Power Button (CM) as /class/input/input4
<6>ACPI: Power Button (CM) [PWRB]
<6>ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 23
<4>fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
<6>[fglrx] Maximum main memory to use for locked dma buffers: 1887 MBytes.
<6>[fglrx] ASYNCIO init succeed!
<6>[fglrx] PAT is enabled successfully!
<6>[fglrx] module loaded - fglrx 8.42.3 [Oct 19 2007] on minor 0
<6>ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 21
<6>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[ff6ff800-ff6fffff] Max Packet=[2048] IR/IT contexts=[4/8]
<6>drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305
<6>usbcore: registered new interface driver usblp
<6>drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
<6>iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
<6>iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
<6>iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
<6>Adding 4192924k swap on /dev/sda6. Priority:-1 extents:1 across:4192924k
<6>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
<7>ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000ee9fb9]
<6>loop: module loaded
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda10, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda9, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on dm-0, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.