Diese Website existiert nur weil wir Werbung mit AdSense ausliefern.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.

Suse 10.3 merkwürdiges /dev/sdb -> Fehlermeldungen beim b

Alles rund um die Systemverwaltung, die Administration und Konfiguration Eures Linuxsystems

Moderator: Moderatoren

Antworten
micha_b
Newbie
Newbie
Beiträge: 35
Registriert: 7. Okt 2006, 15:22

Suse 10.3 merkwürdiges /dev/sdb -> Fehlermeldungen beim b

Beitrag von micha_b » 29. Okt 2007, 23:07

Hallo,

seit Suse 10.3 (vorher 10.2) habe ich ein Problem beim booten. Es wird ein Laufwerk sdb angezeigt und beim Zugriff darauf hagelt es Fehlermeldungen (siehe Auszug aus /var/log/boot.msg). Ich habe aber nur eine SATA Platte (sda) und einen ATA Brenner (sr0) im System. Unter /sys/block/sdb/device/model steht "Config Disk".
Was ist das? Wie werde ich es wieder los?

Gruß
Michael

Core2Duo
2GB RAM
ASUS P5W-DH (Intel 975 Chipsatz)
Seagate SATA Platte am Intel ICH7R
DVD Brenner auch am ICH7R

Code: Alles auswählen

<6>scsi0 : ata_piix
<6>scsi1 : ata_piix
<6>ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001ffa0 irq 14
<6>ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001ffa8 irq 15
<6>ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-H10N, JJ11, max UDMA/66
<6>ata1.00: configured for UDMA/66
<5>scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-H10N  JJ11 PQ: 0 ANSI: 5
<6>ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
<6>ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>scsi2 : ata_piix
<6>scsi3 : ata_piix
<6>ata3: SATA max UDMA/133 cmd 0x000000000001e400 ctl 0x000000000001e082 bmdma 0x000000000001d880 irq 23
<6>ata4: SATA max UDMA/133 cmd 0x000000000001e000 ctl 0x000000000001dc02 bmdma 0x000000000001d888 irq 23
<6>ata3.00: HPA unlocked: 625140335 -> 625142448, native 625142448
<6>ata3.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
<6>ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
<6>ata3.00: configured for UDMA/133
<6>ata4.00: ATA-6: Config  Disk, RGL10364, max UDMA/133
<6>ata4.00: 640 sectors, multi 1: LBA 
<4>ata4.00: Drive reports diagnostics failure. This may indicate a drive
<4>ata4.00: fault or invalid emulation. Contact drive vendor for information.
<4>ata4.00: device is on DMA blacklist, disabling DMA
<6>ata4.00: configured for PIO4
<5>scsi 2:0:0:0: Direct-Access     ATA      ST3320620AS      3.AA PQ: 0 ANSI: 5
<5>scsi 3:0:0:0: Direct-Access     ATA      Config  Disk     RGL1 PQ: 0 ANSI: 5
<6>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>USB Universal Host Controller Interface driver v3.0
<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
<7>PCI: Setting latency timer of device 0000:00:1d.0 to 64
<6>uhci_hcd 0000:00:1d.0: UHCI Host Controller
<5>sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 2:0:0:0: [sda] Write Protect is off
<7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
<5>sd 2:0:0:0: [sda] Write Protect is off
<7>sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1 sda2 < sda5 sda6<6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
<4> sda7<6>uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
<6>usb usb1: new device found, idVendor=0000, idProduct=0000
<4> sda8<6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<4> sda9<6>usb usb1: Product: UHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<4> sda10 >
<6>usb usb1: SerialNumber: 0000:00:1d.0
<5>sd 2:0:0:0: [sda] Attached SCSI disk
<5>sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
<5>sd 3:0:0:0: [sdb] Write Protect is off
<7>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
<5>sd 3:0:0:0: [sdb] Write Protect is off
<7>sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
<6> sdb:<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
<7>PCI: Setting latency timer of device 0000:00:1d.1 to 64
<6>uhci_hcd 0000:00:1d.1: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
<6>uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
<6>usb usb2: new device found, idVendor=0000, idProduct=0000
<6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: UHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<6>usb usb2: SerialNumber: 0000:00:1d.1
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
<7>PCI: Setting latency timer of device 0000:00:1d.2 to 64
<6>uhci_hcd 0000:00:1d.2: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
<6>uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
<6>usb 1-2: new low speed USB device using uhci_hcd and address 2
<6>usb usb3: new device found, idVendor=0000, idProduct=0000
<6>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: UHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<6>usb usb3: SerialNumber: 0000:00:1d.2
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>usb 1-2: new device found, idVendor=046d, idProduct=c046
<6>usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2: Product: USB Optical Mouse
<6>usb 1-2: Manufacturer: Logitech
<6>usb 1-2: configuration #1 chosen from 1 choice
<6>ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
<7>PCI: Setting latency timer of device 0000:00:1d.3 to 64
<6>uhci_hcd 0000:00:1d.3: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
<6>uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ec00
<6>usb usb4: new device found, idVendor=0000, idProduct=0000
<6>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb4: Product: UHCI Host Controller
<6>usb usb4: Manufacturer: Linux 2.6.22.9-0.4-default uhci_hcd
<6>usb usb4: SerialNumber: 0000:00:1d.3
<6>usb usb4: configuration #1 chosen from 1 choice
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
<6>usb 3-2: new full speed USB device using uhci_hcd and address 2
<7>PCI: Setting latency timer of device 0000:00:1d.7 to 64
<6>ehci_hcd 0000:00:1d.7: EHCI Host Controller
<6>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
<6>ehci_hcd 0000:00:1d.7: debug port 1
<7>PCI: cache line size of 32 is not supported by device 0000:00:1d.7
<6>ehci_hcd 0000:00:1d.7: irq 20, io mem 0xffafbc00
<6>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb5: new device found, idVendor=0000, idProduct=0000
<6>usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb5: Product: EHCI Host Controller
<6>usb usb5: Manufacturer: Linux 2.6.22.9-0.4-default ehci_hcd
<6>usb usb5: SerialNumber: 0000:00:1d.7
<6>usb usb5: configuration #1 chosen from 1 choice
<6>hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 8 ports detected
<6>usb 5-7: new high speed USB device using ehci_hcd and address 4
<6>usb 5-7: new device found, idVendor=05e3, idProduct=0606
<6>usb 5-7: new device strings: Mfr=0, Product=1, SerialNumber=0
<6>usb 5-7: Product: USB2.0 Hub
<6>usb 5-7: configuration #1 chosen from 1 choice
<6>hub 5-7:1.0: USB hub found
<6>hub 5-7:1.0: 4 ports detected
<6>usb 1-2: USB disconnect, address 2
<6>usbcore: registered new interface driver hiddev
<6>usb 1-2: new low speed USB device using uhci_hcd and address 3
<6>usb 1-2: new device found, idVendor=046d, idProduct=c046
<6>usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2: Product: USB Optical Mouse
<6>usb 1-2: Manufacturer: Logitech
<6>usb 1-2: configuration #1 chosen from 1 choice
<6>usb 3-2: new full speed USB device using uhci_hcd and address 3
<6>usb 3-2: new device found, idVendor=067b, idProduct=2305
<6>usb 3-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 3-2: Product: IEEE-1284 Controller
<6>usb 3-2: Manufacturer: Prolific Technology Inc.
<6>usb 3-2: configuration #1 chosen from 1 choice
<6>input: Logitech USB Optical Mouse as /class/input/input2
<6>input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-2
<6>usbcore: registered new interface driver usbhid
<6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<3>ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
<3>ata4.00: cmd c4/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
<4>         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
<6>ata4: soft resetting link
<4>ata4: port is slow to respond, please be patient (Status 0xd0)
<3>ata4: SRST failed (errno=-16)
<6>ata4: soft resetting link
<4>ata4: port is slow to respond, please be patient (Status 0xd0)
<3>ata4: SRST failed (errno=-16)
<6>ata4: soft resetting link
<4>ata4: port is slow to respond, please be patient (Status 0xd0)
<3>ata4: SRST failed (errno=-16)
<6>ata4: soft resetting link
<3>ata4: SRST failed (errno=-16)
<3>ata4: reset failed, giving up
<4>ata4.00: disabled
<6>ata4: EH complete
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<2>ldm_validate_partition_table(): Disk read failed.
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<3>Buffer I/O error on device sdb, logical block 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 24
<3>Buffer I/O error on device sdb, logical block 3
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 24
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<4> unable to read partition table
<5>sd 3:0:0:0: [sdb] Attached SCSI disk
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<4>Attempting manual resume
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on sda7, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
<4>end_request: I/O error, dev sdb, sector 0
<6>Floppy drive(s): fd0 is 1.44M
<5>scsi 0:0:0:0: Attached scsi generic sg0 type 5
<5>sd 2:0:0:0: Attached scsi generic sg1 type 0
<6>FDC 0 is a post-1991 82077
<5>sd 3:0:0:0: Attached scsi generic sg2 type 0
<3>intel_rng: FWH not detected
<6>ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 19
<7>PCI: Setting latency timer of device 0000:03:00.0 to 64
<6>sky2 0000:03:00.0: v1.14 addr 0xff8fc000 irq 19 Yukon-EC (0xb6) rev 2
<6>sky2 eth0: addr 00:18:f3:93:d3:ab
<6>ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
<7>PCI: Setting latency timer of device 0000:02:00.0 to 64
<6>sky2 0000:02:00.0: v1.14 addr 0xff7fc000 irq 16 Yukon-EC (0xb6) rev 2
<6>sky2 eth1: addr 00:18:f3:93:be:fb
<6>ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
<7>PCI: Setting latency timer of device 0000:00:1b.0 to 64
<4>sr0: scsi3-mmc drive: 102x/102x writer dvd-ram cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<7>sr 0:0:0:0: Attached scsi CD-ROM sr0
<6>iTCO_vendor_support: vendor-support=0
<6>rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
<4>rtc_cmos: probe of 00:03 failed with error -16
<6>input: Power Button (FF) as /class/input/input3
<6>ACPI: Power Button (FF) [PWRF]
<6>input: Power Button (CM) as /class/input/input4
<6>ACPI: Power Button (CM) [PWRB]
<6>ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 23
<4>fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
<6>[fglrx] Maximum main memory to use for locked dma buffers: 1887 MBytes.
<6>[fglrx] ASYNCIO init succeed!
<6>[fglrx] PAT is enabled successfully!
<6>[fglrx] module loaded - fglrx 8.42.3 [Oct 19 2007] on minor 0
<6>ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 21
<6>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]  MMIO=[ff6ff800-ff6fffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
<6>drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305
<6>usbcore: registered new interface driver usblp
<6>drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
<6>iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
<6>iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
<6>iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
<6>Adding 4192924k swap on /dev/sda6.  Priority:-1 extents:1 across:4192924k
<6>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
<7>ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d80000ee9fb9]
<6>loop: module loaded
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on sda10, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on sda9, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS on dm-0, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.


Werbung:
micha_b
Newbie
Newbie
Beiträge: 35
Registriert: 7. Okt 2006, 15:22

Beitrag von micha_b » 30. Okt 2007, 17:06

Über Google habe ich das Gleiche Problem (soweit ich das Italienisch verstehe ;-) in anderen Foren gefunden.

Laut linux-ide Mailingliste hat diese "Config Disk" irgendwas mit PMP zu tun und zumindest das lange Warten und Resetten des Geräts beim Booten ist mit einem vanilla-Kernel verschwunden.
Also warte ich wohl auf ein Suse 10.3-Kernelupdate.
http://www.mail-archive.com/linux-ide@v ... 09934.html

Edit: Es scheint wirklich spezifisch für mein ASUS P5W-DH Board zu sein:
http://www.mail-archive.com/linux-ide@v ... 11208.html

Gab es da nicht eine Bootoption, um bestimmte SATA-Ports nicht zu scannen? Vielleicht könnte ich den Kernel so von /dev/sdb fernhalten.

jengelh
Guru
Guru
Beiträge: 4039
Registriert: 20. Nov 2004, 17:42
Kontaktdaten:

Beitrag von jengelh » 30. Okt 2007, 23:05

Das ganze gebackporte nervt manchmal echt (pata_ali das ich verwende, wurde dabei auch negativ touchiert...) :x
Insofern, ja, ein Vanilla-Kernel macht's erstmal :? - oder vielleicht tut's auch ein SUSE-basierter 2.6.23.1 nun?

Benutzeravatar
misiu
Moderator
Moderator
Beiträge: 3986
Registriert: 8. Mär 2004, 11:27
Wohnort: bei Schweinfurt

Beitrag von misiu » 31. Okt 2007, 21:02

Kann es sein, dass in:
/boot/grub/device.map
(hd1) /dev/sdb
steht , obwohl
du kein sdb hast?
Kannst du vielleicht im BIOS die SATA, die nicht gebraucht werden abschalten?

MfG
misiu

Antworten

Wer ist online?

Mitglieder in diesem Forum: Baidu [Spider] und 3 Gäste