• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[resolved] Privoxy-Startskript unter SUSE 10.0 geht nicht!

Hallo Leute, das unter [1] abgelegte Startskript von Privoxy führt zu den unter [2] beschriebenen Fehlermeldungen. Was läuft falsch, und wie muss das Skript geändert werden? Für mich sind das nur kryptische Zeilen ...

Die unter [2] genannten Zeilen sind hervorgehoben, damit ihr nicht zählen müsst ;-))

Vielen Danke,


Michael

[1]
Code:
PATH=/usr/local/sbin
P_NAME=Privoxy
# Path to executable.
P_DAEMON=privoxy
# Full path to location of Privoxy config file. 
P_CONF_FILE=/usr/local/etc/privoxy/config
# Full path to PID file location. Location must be writable by 
# whoever runs this script.
P_PIDFILE=/var/run/privoxy.pid
# If uncommented, this script will try to run as USER=privoxy, which
# may require special handling of config, *.action, trust, logfile, 
# jarfile, and pidfile.
P_USER=privoxy

# If a privoxy user is specified, lets try that. /bin/sh does not seem to 
# know about $UID.
if [ "$USER" = "root" ] && [ -n "$P_USER" ] && id $P_USER >/dev/null; then
  P_OWNER=$P_USER
else 
  P_OWNER=$USER
fi

if [ ! -f $P_CONF_FILE ]; then
  echo "Can't find $P_CONF_FILE, exiting."
  exit 1
fi

case "$1" in
 
 start)
     if [ -f $P_PIDFILE ]; then
[B]       if kill -0 `cat $P_PIDFILE`; then[/B]
         echo "Error: $P_NAME is already running, exiting."
         exit 1
       else
[B]         rm -f $P_PIDFILE[/B]
       fi
     fi

	$P_DAEMON --pidfile $P_PIDFILE --user $P_OWNER $P_CONF_FILE 2>/dev/null
     
     if [ $? -eq 0 ]; then
       echo "Starting $P_NAME, OK." 
     else
       echo "Starting $P_NAME, Failed."
[B]       rm -f $P_PIDFILE[/B]
     fi
     ;;
 
 restart)
     $0 stop
     $0 start
     ;;
 
 stop)
     test ! -f $P_PIDFILE && echo "No $P_PIDFILE file found, exiting." && exit 1
     kill `cat $P_PIDFILE` && rm -f $P_PIDFILE && \
     echo "Stopping $P_NAME, OK." || echo "Stopping $P_NAME, failed."
     ;;
 
 *)
     echo "Usage: $0 {start|stop|restart}"
     exit 1
     ;;

esac

exit 0
-----------------------------------------------------------------------------------------------------------------------------------
[2]
./privoxy: line 109: cat: command not found
kill: usage: kill [-s sigspec | -n signum | -sigspec] [pid | job]... or kill -l [sigspec]
./privoxy: line 113: rm: command not found
Starting Privoxy, Failed.
./privoxy: line 123: rm: command not found
 

framp

Moderator
Teammitglied
cat und rm werden nicht gefunden. 'which cat' bzw 'which rm' zeigt Dir wo die stehen. Dann den PATH entsprechend anpassen.
 

framp

Moderator
Teammitglied
Fein. Hast Du schon http://www.linux-club.de/ftopic66639.html gelesen? Nach der erfolgreichen Threadbeantwortung ist immer noch etwas Paperwork vom Autor notwendig :roll:
 
Oben