IRQ 9???! + Kernel-Update Probleme

Alles rund um die Systemverwaltung, die Administration und Konfiguration Eures Linuxsystems

Moderator: Moderatoren

Antworten
sn00p
Newbie
Newbie
Beiträge: 2
Registriert: 25. Dez 2004, 18:56

IRQ 9???! + Kernel-Update Probleme

Beitrag von sn00p » 28. Dez 2004, 12:08

Hallo,

ich habe neulich meinen Kernel upgedatet (über "Systemupdate" in SuSE 9.1), danach die Grafikkartentreiber in den Kernel kompiliert, wie hier im Forum beschrieben wurde (ATI Radeon Treiberproblematik). 3D-Unterstützung funktioniert nun.
Dann habe ich noch auch KDE 3.3.2 geupdatet.

PROBLEM 1:
Seit kurzen bekomme ich jedoch jedesmal wenn ich Linux start nach kurzer Zeit folgende Meldung:


Message from syslogd@sn00p at Tue Dec 28 10:59:54 2004 ...
linux kernel: Disabling IRQ #9

Kann sein, dass es mit meiner Soundkarte zusammenhängt? Die funktioniert nämlich noch nicht (Audigy LS)...

Alles läuft jedoch sonst problemlos.... außer, dass ich den Rechner nicht mehr herunterfahren kann. Lediglich mit dem root Kommando shutdown -h now gehts...

PROBLEM 2:
Um dieses Problem zu lösen, wollte ich den Kernel komplett updaten. Jedoch geht "Systemupdate" unter YAST auch nicht.
Unter Installationseinstellungen findet sich folgends:

Die Paketdaten konnten nicht vom Installationsmedium gelesen werden. Es liegt möglicherweise ein Fehler am Installationsmedium vor.
ERROR: No proposal

Manuelle Intervention ist erforderlich
Betroffene Pakete: 35


Kann mir bitte jemand helfen?


P.S. dmesg gibt folgendes aus (man beachte auch die fglrx Einträge):

Code: Alles auswählen

Linux version 2.6.5-7.111.19-smp (geeko@buildhost) (gcc version 3.3.3 (SuSE Linu
x)) #1 SMP Fri Dec 10 15:10:58 UTC 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
 BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
 BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
 BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable)
 BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
128MB vmalloc/ioremap area available.
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7170
On node 0 totalpages: 262016
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 32640 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 PTLTD                                     ) @ 0x000f7100
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x3fefcf28
ACPI: FADT (v001 AMD    TECATE   0x06040000 PTL  0x000f4240) @ 0x3fefef2e
ACPI: MADT (v001 PTLTD           APIC   0x06040000  LTP 0x00000000) @ 0x3fefefa2
ACPI: DSDT (v001    AMD  AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ES7000: did not find Unisys ACPI OEM table!
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
Processor #1 6:10 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda5 vga=0x314 desktop resume= splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
CKRM Initialization
...... Initializing ClassType<taskclass> ........
...... Initializing ClassType<socket_class> ........
CKRM Initialization done
Detected 2133.359 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Memory: 1032712k/1048064k available (2228k kernel code, 14384k reserved, 760k da
ta, 244k init, 130496k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4194.30 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux:  Disabled at boot.
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU:     After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:     After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU:     After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) MP 2800+ stepping 00
per-CPU timeslice cutoff: 1462.85 usecs.
task migration cache decay timeout: 2 msecs.
masked ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4259.84 BogoMIPS
CPU:     After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:     After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU:     After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) Processor stepping 00
Total of 2 processors activated (8454.14 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not co
nnected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2133.0242 MHz.
..... host bus clock speed is 266.0655 MHz.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Looking for DSDT in initrd ...No customized DSDT found in initrd!
Freeing initrd memory: 1206k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
Linux Plug and Play Support v0.97 (c) Adam Belay
00:00:08[A] -> 2-20 -> IRQ 20 level low
00:00:08[B] -> 2-21 -> IRQ 21 level low
00:00:08[C] -> 2-22 -> IRQ 22 level low
00:00:08[D] -> 2-23 -> IRQ 23 level low
00:01:05[A] -> 2-18 -> IRQ 18 level low
00:01:05[B] -> 2-19 -> IRQ 19 level low
00:02:04[A] -> 2-16 -> IRQ 16 level low
00:02:04[B] -> 2-17 -> IRQ 17 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 06000000
.......     : arbitration: 06
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 000 00  1    0    0   0   0    0    0    00
 01 0FF 0F  0    0    0   0   0    1    1    39
 02 0FF 0F  0    0    0   0   0    1    1    31
 03 0FF 0F  0    0    0   0   0    1    1    41
 04 0FF 0F  0    0    0   0   0    1    1    49
 05 0FF 0F  0    0    0   0   0    1    1    51
 06 0FF 0F  0    0    0   0   0    1    1    59
 07 0FF 0F  0    0    0   0   0    1    1    61
 08 0FF 0F  0    0    0   0   0    1    1    69
 09 0FF 0F  0    1    0   1   0    1    1    71
 0a 0FF 0F  0    0    0   0   0    1    1    79
 0b 0FF 0F  0    0    0   0   0    1    1    81
 0c 0FF 0F  0    0    0   0   0    1    1    89
 0d 0FF 0F  0    0    0   0   0    1    1    91
 0e 0FF 0F  0    0    0   0   0    1    1    99
 0f 0FF 0F  0    0    0   0   0    1    1    A1
 10 003 03  1    1    0   1   0    1    1    D9
 11 003 03  1    1    0   1   0    1    1    E1
 12 003 03  1    1    0   1   0    1    1    C9
 13 003 03  1    1    0   1   0    1    1    D1
 14 003 03  1    1    0   1   0    1    1    A9
 15 003 03  1    1    0   1   0    1    1    B1
 16 003 03  1    1    0   1   0    1    1    B9
 17 003 03  1    1    0   1   0    1    1    C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off
'
vesafb: framebuffer at 0xe0000000, mapped to 0xf8808000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:57b0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Starting balanced_irq
Initial HugeTLB pages allocated: 0
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Initializing Cryptographic API
BIOS failed to enable PCI standards compliance, fixing this error.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 27761 byt
es,<6>...found (800x600, 11810 bytes, v3).
Console: switching to colour frame buffer device 92x32
Real Time Clock Driver v1.12
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD7441: IDE controller at PCI slot 0000:00:07.1
AMD7441: chipset revision 4
AMD7441: not 100% native mode: will probe irqs later
AMD7441: 0000:00:07.1 (rev 04) UDMA100 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 6Y080P0, ATA DISK drive
hdb: Maxtor 91301U3, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SAMSUNG DVD-ROM SD-616Q, ATAPI CD/DVD-ROM drive
hdd: Maxtor 6Y200P0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
 hda: hda1 hda2 < hda5 hda6 >
hdb: max request size: 128KiB
hdb: 25410672 sectors (13010 MB) w/512KiB Cache, CHS=25209/16/63, UDMA(66)
 hdb: hdb1
hdd: max request size: 1024KiB
hdd: 398297088 sectors (203928 MB) w/7936KiB Cache, CHS=24792/255/63, UDMA(100)
 hdd: hdd1
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
reiserfs: using flush barriers
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 244k freed
reiserfs: enabling write barrier flush mode
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
subfs 0.9
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hdd1.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
sundance.c:v1.01+LK1.09a 10-Jul-2003  Written by Donald Becker
  http://www.scyld.com/network/sundance.html
eth0: D-Link DFE-550TX FAST Ethernet Adapter at 0x3000, 00:0d:88:6f:d4:58, IRQ 1
7.
eth0: MII PHY found at address 1, status 0x7829 advertising 01e1.
eth0: Link changed:
NET: Registered protocol family 17
eth0: Link changed: 100Mbps, full duplex
hw_random: AMD768 system management I/O registers at 0x8000.
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AMD 760MP chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 256M @ 0xd0000000
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:02:00.0: OHCI Host Controller
ohci_hcd 0000:02:00.0: irq 19, pci mem f9b08000
ohci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.5-7.111.19-smp ohci_hcd
usb usb1: SerialNumber: 0000:02:00.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:08.0: 3Com PCI 3c905C Tornado at 0x3080. Vers LK1.1.19
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: task_no_data_intr: error=0x04 { DriveStatusError }
Non-volatile memory driver v1.2
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
SCSI subsystem initialized
st: Version 20040318, fixed bufsize 32768, s/g segs 256
BIOS EDD facility v0.13 2004-Mar-09, 2 devices found
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
fglrx: no version for "struct_module" found: kernel tainted.
fglrx: unsupported module, tainting kernel.
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERM
ANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 928 MBytes.
[fglrx] module loaded - fglrx 3.14.1 [Sep 27 2004] on minor 0
mtrr: 0xe0000000,0x8000000 overlaps existing 0xe0000000,0x1000000
[fglrx:firegl_addmap] *ERROR* mtrr allocation failed (-22)
[fglrx] AGP detected, AgpState   = 0x0f000207 (hardware caps of chipset)
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:05.0 into 4x mode
[fglrx] AGP enabled,  AgpCommand = 0x0f000304 (selected caps)
[fglrx] free  AGP = 256126976
[fglrx] max   AGP = 256126976
[fglrx] free  LFB = 116387840
[fglrx] max   LFB = 116387840
[fglrx] free  Inv = 134217728
[fglrx] max   Inv = 134217728
[fglrx] total Inv = 134217728
[fglrx] total TIM = 0
[fglrx] total FB  = 0
[fglrx] total AGP = 65536
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
irq 9: nobody cared!
Call Trace:
 [<c010c064>] __report_bad_irq+0x24/0x90
 [<c010c384>] do_IRQ+0x184/0x1f0
 [<c010a168>] common_interrupt+0x18/0x20
 [<c01072a0>] default_idle+0x0/0x40
 [<c01072c9>] default_idle+0x29/0x40
 [<c0107f44>] cpu_idle+0x24/0x50
 [<c03ee70a>] start_kernel+0x34a/0x3d0
 [<c03ee100>] unknown_bootoption+0x0/0x190

handlers:
[<c020765b>] (acpi_irq+0x0/0x14)
Disabling IRQ #9

Werbung:
Antworten

Wer ist online?

Mitglieder in diesem Forum: Bing [Bot] und 2 Gäste