Probleme mit Energiesparmanagement bei Leap [gelöst]

shorn · 9 Jan. 2016

Hallo,
nach mehreren Jahren Abstinenz bin ich mit Leap wieder zu openSUSE zurück gekehrt. Die Installation mit Gnome-Desktop auf dem Laptop verlief ohne Probleme. Es gibt jedoch Probleme mit dem Energiesparmanagement. Der Laptop kann im Akku-Modus wesentlich kürzer benutzt werden als zum Beispiel mit Debian Wheezy und Jessy, die vorher auf dem Laptop liefen. tlp und powertop sind installiert.
Ich habe daraufhin mal nach Kernel-Fehlern im Journaleintrag geschaut und folgendes gefunden:

Code:

acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM

dmesg liefert:

Code:

stefan@acer2:~> dmesg | egrep -i"err|warn|fail|fault|acpi|apic"
[    0.000000] Linux version 4.1.13-5-default (geeko@buildhost) (gcc version 4.8.5 (SUSE Linux) ) #1 SMP PREEMPT Thu Nov 26 16:35:17 UTC 2015 (49475c3)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.1.13-5-default root=UUID=4ae63e1b-786a-40e5-b4a1-53f3c4b9be98 ro resume=/dev/disk/by-uuid/816f1de3-7e1b-42f2-9c02-ed06970cb97d splash=silent quiet showopts
[    0.000000] BIOS-e820: [mem 0x00000000a6ebf000-0x00000000a6fbefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000a6fbf000-0x00000000a6ffefff] ACPI data
[    0.000000] reserve setup_data: [mem 0x00000000a6ebf000-0x00000000a6fbefff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x00000000a6fbf000-0x00000000a6ffefff] ACPI data
[    0.000000] efi:  ACPI=0xa6ffe000  ACPI 2.0=0xa6ffe014  SMBIOS=0xa6ebef98 
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000] MTRR variable ranges enabled:
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000A6FFE014 000024 (v02 ACRSYS)
[    0.000000] ACPI: XSDT 0x00000000A6FFE210 0000A4 (v01 ACRSYS ACRPRDCT 00000001      01000013)
[    0.000000] ACPI: FACP 0x00000000A6FFB000 00010C (v05 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: DSDT 0x00000000A6FEC000 00B8D8 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.000000] ACPI: FACS 0x00000000A6FBA000 000040
[    0.000000] ACPI: UEFI 0x00000000A6FFD000 000236 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: ASF! 0x00000000A6FFC000 0000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: HPET 0x00000000A6FFA000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: APIC 0x00000000A6FF9000 00008C (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: MCFG 0x00000000A6FF8000 00003C (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: SLIC 0x00000000A6FEB000 000176 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000A6FEA000 0006FE (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.000000] ACPI: BOOT 0x00000000A6FE8000 000028 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: ASPT 0x00000000A6FE3000 000034 (v07 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: DBGP 0x00000000A6FE2000 000034 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: FPDT 0x00000000A6FE0000 000044 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: MSDM 0x00000000A6FDF000 000055 (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000A6FDE000 000968 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000A6FDD000 000A92 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: BGRT 0x00000000A6FDC000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.1.13-5-default root=UUID=4ae63e1b-786a-40e5-b4a1-53f3c4b9be98 ro resume=/dev/disk/by-uuid/816f1de3-7e1b-42f2-9c02-ed06970cb97d splash=silent quiet showopts
[    0.000039] pid_max: default: 32768 minimum: 301
[    0.000047] ACPI: Core revision 20150410
[    0.011924] ACPI: All ACPI Tables successfully acquired
[    0.058953] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.059402] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.193494] PM: Registering ACPI NVS region [mem 0xa6ebf000-0xa6fbefff] (1048576 bytes)
[    0.199376] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.199378] ACPI: bus type PCI registered
[    0.199380] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.199779] perf_event_intel: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.203716] ACPI: Added _OSI(Module Device)
[    0.203718] ACPI: Added _OSI(Processor Device)
[    0.203720] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.203721] ACPI: Added _OSI(Processor Aggregator Device)
[    0.207067] ACPI: Executed 1 blocks of module-level executable AML code
[    0.211633] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.212229] ACPI: Dynamic OEM Table Load:
[    0.212240] ACPI: SSDT 0xFFFF880149FBD000 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20120215)
[    0.213041] ACPI: Dynamic OEM Table Load:
[    0.213048] ACPI: SSDT 0xFFFF880149FBEC00 000303 (v01 PmRef  ApIst    00003000 INTL 20120215)
[    0.213704] ACPI: Dynamic OEM Table Load:
[    0.213711] ACPI: SSDT 0xFFFF880149FC0E00 000119 (v01 PmRef  ApCst    00003000 INTL 20120215)
[    0.215050] ACPI : EC: EC started
[    0.215183] ACPI: Interpreter enabled
[    0.215190] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150410/hwxface-580)
[    0.215197] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150410/hwxface-580)
[    0.215216] ACPI: (supports S0 S3 S4 S5)
[    0.215218] ACPI: Using IOAPIC for interrupt routing
[    0.215257] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.368112] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.368119] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.368237] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.369721] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.369937] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.370188] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.370444] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.370689] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.371763] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.382851] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.462700] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[    0.462787] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.462869] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.462952] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.463034] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.463116] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[    0.463203] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.463286] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.463385] ACPI: Enabled 6 GPEs in block 00 to 3F
[    0.463426] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.463889] PCI: Using ACPI for IRQ routing
[    0.465809] NetLabel:  unlabeled traffic allowed by default
[    0.474378] pnp: PnP ACPI init
[    0.474483] pnp 00:00: Plug and Play ACPI device, IDs MSF0001 PNP0303 (active)
[    0.474570] pnp 00:01: Plug and Play ACPI device, IDs ETD0500 PNP0f13 (active)
[    0.474811] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.474843] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.474910] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.544137] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.544448] system 00:06: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.544468] pnp: PnP ACPI: found 7 devices
[    0.551147] clocksource acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.584013] PCI: CLS 64 bytes, default 64
[    1.424829] Scanning for low memory corruption every 60 seconds
[    1.426483] io scheduler cfq registered (default)
[    1.432732] intel_idle: lapic_timer_reliable_states 0xffffffff
[    2.821772] ACPI: Power Button [PWRB]
[    2.822855] ACPI: Lid Switch [LID0]
[    2.823007] ACPI: Sleep Button [SLPB]
[    2.823300] ACPI: Power Button [PWRF]
[    2.848361] ACPI: bus type USB registered
[    2.852590] sdhci: Copyright(c) Pierre Ossman
[    2.876032] usb usb1: Manufacturer: Linux 4.1.13-5-default ehci_hcd
[    2.893423] usb usb2: Manufacturer: Linux 4.1.13-5-default ehci_hcd
[    2.945196] [drm] failed to retrieve link info, disabling eDP
[    2.951352] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    3.236195] [drm:ironlake_irq_handler [i915]] *ERROR* CPU pipe A FIFO underrun
[    3.236324] [drm:intel_set_pch_fifo_underrun_reporting [i915]] *ERROR* uncleared pch fifo underrun on pch transcoder A
[    3.236342] [drm:cpt_irq_handler [i915]] *ERROR* PCH transcoder A FIFO underrun
[   11.184182] ACPI: Battery Slot [BAT1] (battery present)
[   11.184356] ACPI: AC Adapter [ACAD] (off-line)
[   11.261661] ACPI Warning: SystemIO range 0x0000000000002040-0x000000000000205F conflicts with OpRegion 0x0000000000002040-0x000000000000204F (\_SB_.PCI0.SBUS.SMBI) (20150410/utaddress-254)
[   11.261669] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.319247] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20150410/utaddress-254)
[   11.319255] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.319259] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150410/utaddress-254)
[   11.319263] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.319265] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150410/utaddress-254)
[   11.319268] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.319269] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150410/utaddress-254)
[   11.319272] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.093617] acer_wmi: Acer Laptop ACPI-WMI Extras
[   12.093856] acer_wmi: Brightness must be controlled by acpi video driver
[   12.094594] acer_wmi: Enabling Launch Manager failed: 0xe2 - 0x0
[   12.097966] acer_wmi: Get 0x1 Device Status failed: 0xe2 - 0x0
[   12.103782] acer_wmi: Get Current Device Status failed: 0xe2 - 0x0
[   14.008468] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   22.448253] acer_wmi: Get Current Device Status failed: 0xe2 - 0x0

Das BIOS ist zwar schon älter, aber ACPI wird unterstützt.

Code:

acer2:/home/stefan #  dmidecode -t bios
# dmidecode 2.12
# SMBIOS entry point at 0xa6ebef98
SMBIOS 2.7 present.

Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
	Vendor: Acer
	Version: V2.02
	Release Date: 08/21/2012
	Address: 0xE0000
	Runtime Size: 128 kB
	ROM Size: 3584 kB
	Characteristics:
		PCI is supported
		BIOS is upgradeable
		BIOS shadowing is allowed
		Boot from CD is supported
		Selectable boot is supported
		EDD is supported
		Japanese floppy for NEC 9800 1.2 MB is supported (int 13h)
		Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
		5.25"/360 kB floppy services are supported (int 13h)
		5.25"/1.2 MB floppy services are supported (int 13h)
		3.5"/720 kB floppy services are supported (int 13h)
		3.5"/2.88 MB floppy services are supported (int 13h)
		8042 keyboard services are supported (int 9h)
		CGA/mono video services are supported (int 10h)
		ACPI is supported
		USB legacy is supported
		BIOS boot specification is supported
		Targeted content distribution is supported
		UEFI is supported
	BIOS Revision: 2.2
	Firmware Revision: 0.0

Was bedeutet die Kernel-Meldung genau und was kann ich machen, um die Akku-Laufzeit wieder deutlich zu erhöhen.
Stefan

spoensche · 10 Jan. 2016

Als erstes solltest du mal dein BIOS aktualisieren. Anschließend überprüfst du bitte die Energiespareinstellungen im BIOS und änderst sie ggf. Danach booten und postest die Ausgabe des von dir verwendeten dmesg Befehls.

shorn · 10 Feb. 2016

Hallo,
hat wegen anderer technischer Probleme etwas länger gedauert.
Bios ist jetzt aktualisiert:

Code:

acer2:/home/stefan # dmidecode -t bios
# dmidecode 2.12
# SMBIOS entry point at 0xaaebef98
SMBIOS 2.7 present.

Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
	Vendor: Acer
	Version: V2.21
	Release Date: 12/16/2013
	Address: 0xE0000
	Runtime Size: 128 kB
	ROM Size: 3584 kB
	Characteristics:
		PCI is supported
		BIOS is upgradeable
		BIOS shadowing is allowed
		Boot from CD is supported
		Selectable boot is supported
		EDD is supported
		Japanese floppy for NEC 9800 1.2 MB is supported (int 13h)
		Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
		5.25"/360 kB floppy services are supported (int 13h)
		5.25"/1.2 MB floppy services are supported (int 13h)
		3.5"/720 kB floppy services are supported (int 13h)
		3.5"/2.88 MB floppy services are supported (int 13h)
		8042 keyboard services are supported (int 9h)
		CGA/mono video services are supported (int 10h)
		ACPI is supported
		USB legacy is supported
		BIOS boot specification is supported
		Targeted content distribution is supported
		UEFI is supported
	BIOS Revision: 2.21
	Firmware Revision: 0.0

Und hier nach einmal die Ausgabe von dmesg:

Code:

acer2:/home/stefan # dmesg | egrep -i"err|warn|fail|fault|acpi|apic"
[    0.000000] Linux version 4.1.15-8-default (geeko@buildhost) (gcc version 4.8.5 (SUSE Linux) ) #1 SMP PREEMPT Wed Jan 20 16:41:00 UTC 2016 (0e3b3ab)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.1.15-8-default root=UUID=4ae63e1b-786a-40e5-b4a1-53f3c4b9be98 ro resume=/dev/disk/by-uuid/816f1de3-7e1b-42f2-9c02-ed06970cb97d splash=silent quiet showopts
[    0.000000] BIOS-e820: [mem 0x00000000aaebf000-0x00000000aafbefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000aafbf000-0x00000000aaffefff] ACPI data
[    0.000000] reserve setup_data: [mem 0x00000000aaebf000-0x00000000aafbefff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x00000000aafbf000-0x00000000aaffefff] ACPI data
[    0.000000] efi:  ACPI=0xaaffe000  ACPI 2.0=0xaaffe014  SMBIOS=0xaaebef98 
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000] MTRR variable ranges enabled:
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000AAFFE014 000024 (v02 ACRSYS)
[    0.000000] ACPI: XSDT 0x00000000AAFFE210 00009C (v01 ACRSYS ACRPRDCT 00000001      01000013)
[    0.000000] ACPI: FACP 0x00000000AAFFB000 00010C (v05 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: DSDT 0x00000000AAFEC000 00BC02 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.000000] ACPI: FACS 0x00000000AAFBA000 000040
[    0.000000] ACPI: UEFI 0x00000000AAFFD000 000236 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: ASF! 0x00000000AAFFC000 0000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: HPET 0x00000000AAFFA000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: APIC 0x00000000AAFF9000 00008C (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: MCFG 0x00000000AAFF8000 00003C (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000AAFEB000 0006FE (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.000000] ACPI: BOOT 0x00000000AAFE9000 000028 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: ASPT 0x00000000AAFE4000 000034 (v07 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: DBGP 0x00000000AAFE3000 000034 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: FPDT 0x00000000AAFE1000 000044 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: MSDM 0x00000000AAFE0000 000055 (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000AAFDF000 000968 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000AAFDE000 000A92 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: BGRT 0x00000000AAFDD000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.1.15-8-default root=UUID=4ae63e1b-786a-40e5-b4a1-53f3c4b9be98 ro resume=/dev/disk/by-uuid/816f1de3-7e1b-42f2-9c02-ed06970cb97d splash=silent quiet showopts
[    0.000039] pid_max: default: 32768 minimum: 301
[    0.000047] ACPI: Core revision 20150410
[    0.011811] ACPI: All ACPI Tables successfully acquired
[    0.057935] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.058383] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.191996] PM: Registering ACPI NVS region [mem 0xaaebf000-0xaafbefff] (1048576 bytes)
[    0.197850] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.197851] ACPI: bus type PCI registered
[    0.197853] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.198253] perf_event_intel: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.202194] ACPI: Added _OSI(Module Device)
[    0.202196] ACPI: Added _OSI(Processor Device)
[    0.202197] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.202198] ACPI: Added _OSI(Processor Aggregator Device)
[    0.205529] ACPI: Executed 1 blocks of module-level executable AML code
[    0.210118] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.210707] ACPI: Dynamic OEM Table Load:
[    0.210717] ACPI: SSDT 0xFFFF880149FBC000 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20120913)
[    0.211516] ACPI: Dynamic OEM Table Load:
[    0.211524] ACPI: SSDT 0xFFFF880149FB2800 000303 (v01 PmRef  ApIst    00003000 INTL 20120913)
[    0.212179] ACPI: Dynamic OEM Table Load:
[    0.212185] ACPI: SSDT 0xFFFF880149FBEE00 000119 (v01 PmRef  ApCst    00003000 INTL 20120913)
[    0.213513] ACPI : EC: EC started
[    0.213646] ACPI: Interpreter enabled
[    0.213652] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150410/hwxface-580)
[    0.213658] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150410/hwxface-580)
[    0.213674] ACPI: (supports S0 S3 S4 S5)
[    0.213677] ACPI: Using IOAPIC for interrupt routing
[    0.213718] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.366379] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.366386] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.366503] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.367776] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.367989] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.368243] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.368491] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.368735] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.369806] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.381342] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.461185] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461272] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461354] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461437] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461518] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461600] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461686] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461767] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.461867] ACPI: Enabled 6 GPEs in block 00 to 3F
[    0.461908] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.462357] PCI: Using ACPI for IRQ routing
[    0.464274] NetLabel:  unlabeled traffic allowed by default
[    0.472890] pnp: PnP ACPI init
[    0.472995] pnp 00:00: Plug and Play ACPI device, IDs MSF0001 PNP0303 (active)
[    0.473081] pnp 00:01: Plug and Play ACPI device, IDs ETD0500 PNP0f13 (active)
[    0.473282] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.473315] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.473382] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.542602] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.542914] system 00:06: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.542934] pnp: PnP ACPI: found 7 devices
[    0.549631] clocksource acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.582479] PCI: CLS 64 bytes, default 64
[    1.438636] Scanning for low memory corruption every 60 seconds
[    1.440320] io scheduler cfq registered (default)
[    1.446551] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.511980] acpi device:14: hash matches
[    2.963461] ACPI: Power Button [PWRB]
[    2.963676] ACPI: Lid Switch [LID0]
[    2.963795] ACPI: Sleep Button [SLPB]
[    2.963923] ACPI: Power Button [PWRF]
[    2.982834] ACPI: bus type USB registered
[    2.991282] sdhci: Copyright(c) Pierre Ossman
[    2.999878] usb usb1: Manufacturer: Linux 4.1.15-8-default ehci_hcd
[    3.015680] usb usb2: Manufacturer: Linux 4.1.15-8-default ehci_hcd
[    3.063512] [drm] failed to retrieve link info, disabling eDP
[    3.069911] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   11.237099] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20150410/utaddress-254)
[   11.237118] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.237127] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150410/utaddress-254)
[   11.237140] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.237146] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150410/utaddress-254)
[   11.237157] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.237162] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150410/utaddress-254)
[   11.237172] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.344161] ACPI: AC Adapter [ACAD] (on-line)
[   11.694156] ACPI: Battery Slot [BAT1] (battery present)
[   12.214481] ACPI Warning: SystemIO range 0x0000000000002040-0x000000000000205F conflicts with OpRegion 0x0000000000002040-0x000000000000204F (\_SB_.PCI0.SBUS.SMBI) (20150410/utaddress-254)
[   12.214501] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.780347] acer_wmi: Acer Laptop ACPI-WMI Extras
[   12.780660] acer_wmi: Brightness must be controlled by acpi video driver
[   12.782884] acer_wmi: Enabling Launch Manager failed: 0xe2 - 0x0
[   14.899908] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

Das Problem mit der Energieverwaltung besteht weiterhin. Gerade wurde mir vom System gesagt, dass ich mit 50 % Akku noch eine Viertelstunde Akku-Laufzeit habe. Das war vor dem Umstieg deutlich besser.
Hat jemand noch eine Idee?
Grüße, Stefan

revealed · 11 Feb. 2016

Zu ASPM:
http://linuxwireless.org/en/users/Documentation/ASPM/

Wie hast du denn TLP konfiguriert? Hilft dir eventuell mein beitrag zum T60 weiter? Siehe sig.

Ich würde ja TLP und powertop nicht gleichzeitig verwenden. Die booten sich gegenseitig aus. Wenn TLP schon eingesetzt wird, dann nur TLP (meiner Meinung nach).

Dann nochmal kurz:
laptopmode-tools, powertop, tuned und eigene scripte deaktivieren. Dafür ganz auf TLP setzen.

smartd und hddtemp deaktivieren.

Warum disabling ASPM gleich mit Error aussteigt, kann ich dir so nich sagen. und evtl mal schauen ob die Festplatte überhaupt schlafen geht:

Code:

watch -n1 "hdparm -C /dev/sda"

Wichtig ist auch, dass du schaust ob die Grafikkarte (runterfährt). Und das CPU trotteling funktioniert. (Das h vergessen fand ich grad lustig).

Was ich meine: Wenn du vorinstalliert latop-modetools hast und dann zusätzlich TLP installierst und beide gleichzeitig laufen, dann wirds nich klappen. Weil grad das sind 2 tools die sehr ähnliche knöpfe zum Stromsparen bedienen. Und einer sagt so, der andere so.

Gruß,

R

PS.: Und gib doch mal Modellnummer und Ausstattung von dem Gerät an. Vielleicht fällt direkt was auf.
PPS.: Und TLP eignet sich halt auch besonders für Thinkpads. Weiss nich, was du hast. Ich komm halt mir meiner konfiguration so auf ca. 2 Stunden bei mäßiger Verwendung das mit einem Akku aus einer Generation bei dem das schon ziemlich viel war, dessen gesamt Lebenszustand noch bei ca. 73 Prozent liegt. Mäßige Verwendung ist für mich. Bissl was surfen, und vielleicht im Libre Office was machen. Also so, dass CPU und Grafikkarte auch mal zur Ruhe kommen und die Festplatte mal 5 min. das Drehen aufhören kann.

shorn · 11 Feb. 2016

Danke für die vielen Informationen.

Fangen wir mal vorne an. laptopmode-tools sind nicht installiert, aber powertop und tuned. Auch TLP und TLP radio device wizard sind installiert. Wenn ich dich richtig verstanden habe, soll ich powertop und tuned deinstallieren.

Laut meinen Infos ist TLP "für alle Notebook-Fabrikate geeignet, das Einstellen der Akkuladeschwellen ist jedoch nur für IBM/Lenovo ThinkPads verfügbar" (http://thinkwiki.de).

Hier die Infos zu TLP, ich habe die Standardeinstellungen nicht geändert.

Code:

acer2:/home/stefan # tlp-stat
--- TLP 0.8 --------------------------------------------

+++ Configured Settings: /etc/default/tlp
TLP_ENABLE=1
TLP_DEFAULT_MODE=AC
DISK_IDLE_SECS_ON_AC=0
DISK_IDLE_SECS_ON_BAT=2
MAX_LOST_WORK_SECS_ON_AC=15
MAX_LOST_WORK_SECS_ON_BAT=60
SCHED_POWERSAVE_ON_AC=0
SCHED_POWERSAVE_ON_BAT=1
NMI_WATCHDOG=0
ENERGY_PERF_POLICY_ON_AC=performance
ENERGY_PERF_POLICY_ON_BAT=powersave
DISK_DEVICES="sda sdb"
DISK_APM_LEVEL_ON_AC="254 254"
DISK_APM_LEVEL_ON_BAT="128 128"
SATA_LINKPWR_ON_AC=max_performance
SATA_LINKPWR_ON_BAT=min_power
PCIE_ASPM_ON_AC=performance
PCIE_ASPM_ON_BAT=powersave
RADEON_POWER_PROFILE_ON_AC=high
RADEON_POWER_PROFILE_ON_BAT=low
RADEON_DPM_STATE_ON_AC=performance
RADEON_DPM_STATE_ON_BAT=battery
RADEON_DPM_PERF_LEVEL_ON_AC=auto
RADEON_DPM_PERF_LEVEL_ON_BAT=auto
WIFI_PWR_ON_AC=1
WIFI_PWR_ON_BAT=5
WOL_DISABLE=Y
SOUND_POWER_SAVE_ON_AC=0
SOUND_POWER_SAVE_ON_BAT=1
SOUND_POWER_SAVE_CONTROLLER=Y
BAY_POWEROFF_ON_BAT=0
BAY_DEVICE="sr0"
RUNTIME_PM_ON_AC=on
RUNTIME_PM_ON_BAT=auto
RUNTIME_PM_ALL=1
RUNTIME_PM_DRIVER_BLACKLIST="radeon nouveau"
USB_AUTOSUSPEND=1
USB_BLACKLIST_WWAN=1
RESTORE_DEVICE_STATE_ON_STARTUP=0

+++ System Info
System         = Acer V2.21 TravelMate P253
BIOS           = V2.21
Release        = "openSUSE Leap 42.1 (x86_64)"
Kernel         = 4.1.15-8-default #1 SMP PREEMPT Wed Jan 20 16:41:00 UTC 2016 (0e3b3ab) x86_64
/proc/cmdline  = BOOT_IMAGE=/boot/vmlinuz-4.1.15-8-default root=UUID=4ae63e1b-786a-40e5-b4a1-53f3c4b9be98 ro resume=/dev/disk/by-uuid/816f1de3-7e1b-42f2-9c02-ed06970cb97d splash=silent quiet showopts
Init system    = systemd

+++ System Status
TLP power save = enabled
power source   = AC

+++ Processor
CPU Model      = Intel(R) Core(TM) i3-2328M CPU @ 2.20GHz

/sys/devices/system/cpu/cpu0/cpufreq/scaling_driver    = intel_pstate
/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor  = powersave
/sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq  =   800000 [kHz]
/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq  =  2200000 [kHz]

/sys/devices/system/cpu/cpu1/cpufreq/scaling_driver    = intel_pstate
/sys/devices/system/cpu/cpu1/cpufreq/scaling_governor  = powersave
/sys/devices/system/cpu/cpu1/cpufreq/scaling_min_freq  =   800000 [kHz]
/sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq  =  2200000 [kHz]

/sys/devices/system/cpu/cpu2/cpufreq/scaling_driver    = intel_pstate
/sys/devices/system/cpu/cpu2/cpufreq/scaling_governor  = powersave
/sys/devices/system/cpu/cpu2/cpufreq/scaling_min_freq  =   800000 [kHz]
/sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq  =  2200000 [kHz]

/sys/devices/system/cpu/cpu3/cpufreq/scaling_driver    = intel_pstate
/sys/devices/system/cpu/cpu3/cpufreq/scaling_governor  = powersave
/sys/devices/system/cpu/cpu3/cpufreq/scaling_min_freq  =   800000 [kHz]
/sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq  =  2200000 [kHz]

/sys/devices/system/cpu/intel_pstate/min_perf_pct      = 36
/sys/devices/system/cpu/intel_pstate/max_perf_pct      = 100
/sys/devices/system/cpu/intel_pstate/no_turbo          = 1

x86_energy_perf_policy: program not installed.

/proc/sys/kernel/nmi_watchdog                          = 0

+++ Undervolting
PHC kernel not available.

+++ Temperatures
CPU temp               =    53 [°C]
Fan speed              = (not available)

+++ File System
/proc/sys/vm/laptop_mode               =     0
/proc/sys/vm/dirty_writeback_centisecs =  1500
/proc/sys/vm/dirty_expire_centisecs    =  1500
/proc/sys/vm/dirty_ratio               =    20
/proc/sys/vm/dirty_background_ratio    =    10
/proc/sys/fs/xfs/age_buffer_centisecs  = (not available)
/proc/sys/fs/xfs/xfssyncd_centisecs    = (not available)
/proc/sys/fs/xfs/xfsbufd_centisecs     = (not available)

+++ Storage Devices
/dev/sda:
          Model     = ST9500325AS                             
          Firmware  = 0001SDM1
          APM Level = 254
          Status    = active/idle
          Scheduler = cfq

        SMART info:
            4 Start_Stop_Count          =    15218 
            5 Reallocated_Sector_Ct     =        0 
            9 Power_On_Hours            =     4494 [h]
          190 Airflow_Temperature_Cel   =       34 [°C]
          193 Load_Cycle_Count          =   155470 
          194 Temperature_Celsius       =       34 (0 18 0 [°C]


+++ SATA Aggressive Link Power Management
/sys/class/scsi_host/host0/link_power_management_policy  = max_performance
/sys/class/scsi_host/host1/link_power_management_policy  = max_performance
/sys/class/scsi_host/host2/link_power_management_policy  = max_performance
/sys/class/scsi_host/host3/link_power_management_policy  = max_performance
/sys/class/scsi_host/host4/link_power_management_policy  = max_performance
/sys/class/scsi_host/host5/link_power_management_policy  = max_performance

+++ PCIe Active State Power Management
/sys/module/pcie_aspm/parameters/policy = default (using bios preferences)

+++ Intel Graphics
/sys/module/i915/parameters/powersave        = (not available)
/sys/module/i915/parameters/enable_rc6       =  1 (enabled)
/sys/module/i915/parameters/enable_fbc       = -1 (use per-chip default)
/sys/module/i915/parameters/lvds_downclock   =  0 (disabled)
/sys/module/i915/parameters/semaphores       = -1 (use per-chip default)

+++ Wireless
bluetooth = none (no device)
wifi      = on
wwan      = none (no device)

wlan0(ath9k)        : connected, power management = off

+++ Audio
/sys/module/snd_hda_intel/parameters/power_save            = 0
/sys/module/snd_hda_intel/parameters/power_save_controller = N

+++ Runtime Power Management
device classes   = all
device blacklist = (not configured)
driver blacklist = radeon nouveau

/sys/bus/pci/devices/0000:00:00.0/power/control = on   (0x060000, Host bridge, no driver)
/sys/bus/pci/devices/0000:00:02.0/power/control = on   (0x030000, VGA compatible controller, i915)
/sys/bus/pci/devices/0000:00:16.0/power/control = on   (0x078000, Communication controller, mei_me)
/sys/bus/pci/devices/0000:00:1a.0/power/control = on   (0x0c0320, USB controller, ehci-pci)
/sys/bus/pci/devices/0000:00:1b.0/power/control = on   (0x040300, Audio device, snd_hda_intel)
/sys/bus/pci/devices/0000:00:1c.0/power/control = on   (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:1c.1/power/control = on   (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:1d.0/power/control = on   (0x0c0320, USB controller, ehci-pci)
/sys/bus/pci/devices/0000:00:1f.0/power/control = on   (0x060100, ISA bridge, lpc_ich)
/sys/bus/pci/devices/0000:00:1f.2/power/control = on   (0x010601, SATA controller, ahci)
/sys/bus/pci/devices/0000:00:1f.3/power/control = on   (0x0c0500, SMBus, no driver)
/sys/bus/pci/devices/0000:02:00.0/power/control = on   (0x020000, Ethernet controller, tg3)
/sys/bus/pci/devices/0000:02:00.1/power/control = on   (0x080501, SD Host controller, sdhci-pci)
/sys/bus/pci/devices/0000:02:00.2/power/control = on   (0x088000, System peripheral, no driver)
/sys/bus/pci/devices/0000:02:00.3/power/control = on   (0x088000, System peripheral, no driver)
/sys/bus/pci/devices/0000:03:00.0/power/control = on   (0x028000, Network controller, ath9k)

+++ USB
autosuspend        = enabled
device whitelist   = (not configured)
device blacklist   = (not configured)
wwan blacklist     = enabled

Bus 002 Device 002 ID 8087:0024 control = auto, autosuspend_delay_ms =     0 -- Intel Corp. Integrated Rate Matching Hub (hub)
Bus 002 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms =     0 -- Linux Foundation 2.0 root hub (hub)
Bus 001 Device 003 ID 04f2:b337 control = auto, autosuspend_delay_ms =  2000 -- Chicony Electronics Co., Ltd  (uvcvideo)
Bus 001 Device 002 ID 8087:0024 control = auto, autosuspend_delay_ms =     0 -- Intel Corp. Integrated Rate Matching Hub (hub)
Bus 001 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms =     0 -- Linux Foundation 2.0 root hub (hub)

+++ Battery Status
/sys/class/power_supply/BAT1/manufacturer                   = PANASONIC 
/sys/class/power_supply/BAT1/model_name                     = Li_Ion_4000mA 
/sys/class/power_supply/BAT1/cycle_count                    = (not supported)
/sys/class/power_supply/BAT1/charge_full_design             =   4400 [mAh]
/sys/class/power_supply/BAT1/charge_full                    =    486 [mAh]
/sys/class/power_supply/BAT1/charge_now                     =    335 [mAh]
/sys/class/power_supply/BAT1/current_now                    =    568 [mA]
/sys/class/power_supply/BAT1/status                         = Charging

In der Hardware-Info fand ich folgende Zeile, was wohl ein Teil des Problems sein könnte:

Code:

<4>[  791.244039] [Firmware Bug]: battery: (dis)charge rate invalid.

Grüße, Stefan

revealed · 11 Feb. 2016

Fangen wir mal vorne an. laptopmode-tools sind nicht installiert, aber powertop und tuned. Auch TLP und TLP radio device wizard sind installiert. Wenn ich dich richtig verstanden habe, soll ich powertop und tuned deinstallieren.

Nein.

Ich würde versuchen:

Code:

systemctl disable tuned
systemctl stop tuned
systemctl disable 
systemctl stop laptop-modetools
systemctl disable laptop-modetools
systemctl stop smartd
systemctl disable smartd
systemctl stop hddtemp
systemctl disable hddtemp

....
Im KDE möchtest du eventuell auch die Indexing Dienste usw. abschalten.

Und bist du dir sicher dass TLP läuft?

Code:

systemctl status tlp

Freilig kannst du dir in Powertop ansehen was so alles eingestellt ist und welchem Modus es läuft. Du musst nichts löschen. Ich hab es auch noch installiert, weil man einfach mal schön nachschauen kann usw. Das hilft beim Tunen.

Was du mit Powertop nicht tun solltest ist -- da gibts diesen Autotuning Modus. (Klar der stellt dann evtl. was ungewollt um.)
Oder gar die Ausgaben in einen Script packen und via boot.local starten. (Schiesst auch quer).

Code:
Code:

<4>[ 791.244039] [Firmware Bug]: battery: (dis)charge rate invalid.

Da solltest mal nachsehen.

Was werkelt in der Kiste denn an Grafikkarte? Und Prozessor?
- Also bei der Intel HD grafik geh ich mal davon aus, dass die das Stromsparen beherrscht. Wie man bei der Einfluss nimmt kenne ich mich nicht aus.
- Core i3 sollte vom Betriebssystem anstandslos abgehandelt werden, ohne jegliches weiteres Zutun.

Was ich auf die Schnelle sehe, was mir nicht gefällt:

Code:

/sys/class/scsi_host/host0/link_power_management_policy  = max_performance

Dein Festplattencontroller läuft vollgas. (Das is warscheinlich weil grad am Kabel hängst?)

Code:

WIFI_PWR_ON_BAT=5

Nicht jede WIFI kann das, da müsstest evtl mal sehen ob sie kann.

Empfehlungsweise schaust du dir die TLP config nochmal an, da stimmt was nicht. Siehst ja. Ich kann nicht viel mehr tun als dir den Link hier hinknallen:
http://linrunner.de/en/tlp/docs/tlp-configuration.html

Und das mit den 2 Fehlermeldungen die do so schön hervorhebst, denen müsstest du eventuell auch nachgehen. Vorallem das mit dem Akku klingt sehr suspekt. Ich hab n bissl nachgelesen und gelange zu dem Schluss, dass in Verbindung mit deiner Hardware und sysfs es sein könnte, dass aufgrund der verwendung von veralteten sysfs strukturen da zu dieser Meldung kommt.

PS.: Auf das mit der Eignung gehe ich nicht weiter ein. Das ist ok so und kann man so stehen lassen. Das zwischen den Zeilen gelese nervt.
PPS.: Eventuell magst du auch doch noch mal beobachten ob CPU frequenz Skalierung funktioniert:

Code:

watch -n1 "cpupower frequency-info | grep momentan"

Viel viel mehr fällt mir nicht ein, außer mein Beweis Notebook und die Tipps. Und ich meine irgendwo herausgelesen zu haben dass bestimmte Entwickler bestimmter Pakete bestimmte Distris bevorzugt selber benutzen. Freilig kann es sein, dass die Unterstützung dort besser ist.

Gruß,

R

shorn · 14 Feb. 2016

Ich habe auch mal in Yast2 bei der Dienste-Verwaltung nachgesehen, ob ACPI überhaupt läuft, das ist aber nicht der Fall.

Code:

acpid.service - ACPI Event Daemon
   Loaded: loaded (/usr/lib/systemd/system/acpid.service; disabled)
   Active: inactive (dead)

TLP läuft:

Code:

tlp.service - TLP system startup/shutdown
   Loaded: loaded (/usr/lib/systemd/system/tlp.service; enabled)
   Active: active (exited) since Sun 2016-02-14 11:57:31 CET; 58min ago
  Process: 1245 ExecStart=/usr/sbin/tlp init start (code=exited, status=0/SUCCESS)
 Main PID: 1245 (code=exited, status=0/SUCCESS)
   CGroup: /system.slice/tlp.service

Feb 14 11:57:31 acer2 tlp[1245]: Loading kernel modules...done.
Feb 14 11:57:31 acer2 tlp[1245]: Applying power save settings...done.
Feb 14 11:57:31 acer2 tlp[1245]: Setting battery charge thresholds...done.

Soll ich also ACPI erst einmal starten bzw. aktivieren? Was ist eigentlich der Unterschied?
Grüße, Stefan

spoensche · 14 Feb. 2016

Der ACPI-Daemon empfängt Events, die von der Hardware bzw. vom BIOS/EFI an das Betriebssystem geschickt werden. Der TLP konfiguriert das System, wie es sich verhalten soll, wenn der Laptop am Netzteil hängt bzw. wenn er eben nicht am Netzteil hängt.

shorn · 14 Feb. 2016

Der ACPI-Daemon empfängt Events, die von der Hardware bzw. vom BIOS/EFI an das Betriebssystem geschickt werden.

Ja, ich weiß. Aber das geht doch nur, wenn er aktiv ist. Also doch manuell aktivieren, weil nicht automatisch geschehen?
Stefan

josef-wien · 14 Feb. 2016

shorn schrieb:
nicht automatisch geschehen?

Meint

Code:

ps -C acpid

das auch?

shorn · 15 Feb. 2016

Nachdem ACPI läuft, habe ich mit TLP den Akku-Status geprüft.

Code:

acer2:/home/stefan # tlp-stat -b
--- TLP 0.8 --------------------------------------------

+++ Battery Status
/sys/class/power_supply/BAT1/manufacturer                   = PANASONIC
/sys/class/power_supply/BAT1/model_name                     = Li_Ion_4000mA
/sys/class/power_supply/BAT1/cycle_count                    = (not supported)
/sys/class/power_supply/BAT1/charge_full_design             =   4400 [mAh]
/sys/class/power_supply/BAT1/charge_full                    =    485 [mAh]
/sys/class/power_supply/BAT1/charge_now                     =    485 [mAh]
/sys/class/power_supply/BAT1/current_now                    =      1 [mA]
/sys/class/power_supply/BAT1/status                         = Full

Wenn ich das richtig lese, liegt der Wert für charge_full bei etwa 10 % vom Ist-Wert (charge_full_design).
Das dürfte erklären, warum der Akku nicht voll geladen wird. Dieses Problem trat erst auf mit dem Wechsel von Debian zu openSUSE.
Kann ich den Wert für charge_full manuell ändern?
Grüße, Stefan

shorn · 17 März 2016

Ich habe den Akku jetzt ausgetauscht. Die Ausgabe von tlp-stat ist unten angehängt. Ich hatte angenommen, dass TLP Angaben wie charge_full aus einem config-file ausliest und der Wert falsch sei. Jetzt bin ich da auch schlauer. Warum die Akku-Kapazität so (gefühlt) eingebrochen ist, weiß ich auch nicht.
Danke und viele Grüße
Stefan

Code:

acer2:/home/stefan # tlp-stat -b
--- TLP 0.8 --------------------------------------------

+++ Battery Status
/sys/class/power_supply/BAT1/manufacturer                   = Simplo 
/sys/class/power_supply/BAT1/model_name                     = Li_Ion_4000mA 
/sys/class/power_supply/BAT1/cycle_count                    = (not supported)
/sys/class/power_supply/BAT1/charge_full_design             =   6600 [mAh]
/sys/class/power_supply/BAT1/charge_full                    =   6557 [mAh]
/sys/class/power_supply/BAT1/charge_now                     =   5835 [mAh]
/sys/class/power_supply/BAT1/current_now                    =    826 [mA]
/sys/class/power_supply/BAT1/status                         = Discharging

Probleme mit Energiesparmanagement bei Leap [gelöst]

shorn

Member

spoensche

Moderator

shorn

Member

revealed

Guru

shorn

Member

revealed

Guru

shorn

Member

spoensche

Moderator

shorn

Member

josef-wien

Ultimate Guru

shorn

Member

shorn

Member