• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst]Installation scheitert an nicht erkannter Festplatte

H

halo44

Hacker
Alle Recherchen im Forum haben mich bei der Lösung meines neuesten Problems nicht weitergebracht. Vielleicht könnt Ihr mir ein paar Hilfen geben.

Ich versuche vergeblich auf dem Rechner (Fujitsu Siemens Esprimo P2530) meiner Frau openSuse zusätzlich zum einwandfrei laufenden Windows 7 zu installieren. Ich habe die Versionen 12.1 und 12.2 in 64 und 32 Bit von CD und DVD, sogar von einer NetInstallCD, versucht. Auch die Installation von Kubuntu 12.04 gelang nicht.

Allerdings verlief die Installation von Debian 6.0.5 (Kernel 2.6.32) völlig problemlos. Ich habe also neben Windows auch ein laufendes Linuxsystem auf dem Rechner und kann damit mit Eurer Anleitung Informationen zum Rechner liefern. Vielleicht bekommen wir openSuse doch noch installiert.

Nun zu den Symptomen:

a.) openSUSE 12.2-64 KDE Live-CD

Nach der Sprachauswahl wird der Linux-Kernel geladen, der Monitor wird für fast eine Minute schwarz. Dann erscheint eine Zeile
Code: 
ata-1 COMRESET failed errno=-16
Der Monitor wird wieder kurz dunkel, dann erscheint das Chamäleon und der Schriftzug openSUSE auf dem grünen Hintergrund, wobei das untere Viertel des Monitors schwarz bleibt. Danach erscheint auf schwarzem Hintergrund
Code: 
... Pointer to flat panel table invalid
... failed to find MBR identifier
... reboot in 120 seconds
Weiter gehts nicht.

b.) openSUSE NetInstallCD 12.2

Nach Sprachauswahl und der Installationsoption wird der Linux-Kernel geladen. Danach erscheint das Chamäleon auf grünem Hintergrund (ohne Schriftzug openSUSE), dafür ein Laufbalken, der sich allerdings nicht bewegt. Nach fast einer Minute kommt das Chamäleon, jetzt mit dem Schriftzug und nach wieder fast einer Minute laufen sehr schnell einige Kommandozeilen durch.

Danach werden in dem normalen grafischen Bild die deutschen Lizenzbestimmungen zur Zustimmung gezeigt und danach die Systemanalyse gestartet.

Ergebnis: Es wurden keine Festplatten für die Installation gefunden. Bitte überprüfen Sie Ihre Hardware.

Nach Betätigung von OK läuft die Installation weiter über Zeitzone etc., scheitert dann aber, weil mangels Festplatten keine Partitionierung möglich ist.

c.) Kubuntu 12.04-64 Live CD

Nach der Sprachauswahl und Start der Installation wird der Monitor für etwa eine Minute dunkel, bevor das KDE-Symbol mit den fünf laufenden Punkten wieder für eine Minute erscheint.

Danach wird auf schwarzem Hintergrund gemeldet
Code: 
... BusyBox v1.18.5 ...
(initramfs) Unable to find a medium containing a live system
Dann gehts nicht weiter.

d.) Interessant sind vielleicht auch noch folgende Infos: wenn ich den Rechner von einer externen
Festplatte (auf der ich ein Kubuntu istalliert habe) boote, so fährt dieses System hoch, erkennt
aber die Festplatten des Rechners nicht. Fdisk zeigt nur die Partitionen auf der externen Platte.
Das gleiche Verhalten zeigt sich beim Booten eines Systems von einem USB-Stick.

Des Pudels Kern scheint wohl irgendwo bei der Erkennung von Festplatte/CD/DVD zu liegen.

Ich würde trotz laufendem Debian gerne die Suse auf den Rechner bringen und hoffe hier auf Eure
Unterstützung.

Gruss H.
 
RME

RME

Advanced Hacker
Hallo,
d.) Interessant sind vielleicht auch noch folgende Infos: wenn ich den Rechner von einer externen
Festplatte (auf der ich ein Kubuntu istalliert habe) boote, so fährt dieses System hoch, erkennt
aber die Festplatten des Rechners nicht. Fdisk zeigt nur die Partitionen auf der externen Platte.
Das gleiche Verhalten zeigt sich beim Booten eines Systems von einem USB-Stick.
Zum Vergrößern anklicken....
Ich wage eine Vermutung: die Partitionstabelle der Festplatte ist defekt (z.B. überlappende Partitionen).

Da Du mit "fdisk -l" nichts siehst:

Lade von hier:

http://sourceforge.net/projects/bootinfoscript/

das Paket bootinfoscript-061.tar.gz herunter; dann entpacken, ergibt:

bootinfoscript VERSION='0.61' RELEASE_DATE='1 April 2012'; (oder neuer)

(lese die README Datei)

Lass es laufen (entweder vom installierten Debian oder von einem Live-Linux):
Code: 
su -
./bootinfoscript <outputfile>
und poste die Resultat-Datei.

Gruss,
Roland
 
OP
H

halo44

Hacker
Guten Morgen Roland,

hier die Ausgabe des Scripts (unter debian):
Code: 
                  Boot Info Script 0.61      [1 April 2012]


============================= Boot Info Summary: ===============================

 => Grub2 (v1.97-1.98) is installed in the MBR of /dev/sda and looks at sector 
    1 of the same hard drive for core.img. core.img is at this location and 
    looks in partition 5 for (,msdos5)/boot/grub.

sda1: __________________________________________________________________________

    File system:       ntfs
    Boot sector type:  Windows Vista/7: NTFS
    Boot sector info:  No errors found in the Boot Parameter Block.
    Operating System:  
    Boot files:        /bootmgr /Boot/BCD

sda2: __________________________________________________________________________

    File system:       ntfs
    Boot sector type:  Windows Vista/7: NTFS
    Boot sector info:  No errors found in the Boot Parameter Block.
    Operating System:  Windows 7
    Boot files:        /Windows/System32/winload.exe

sda3: __________________________________________________________________________

    File system:       ntfs
    Boot sector type:  Windows Vista/7: NTFS
    Boot sector info:  No errors found in the Boot Parameter Block.
    Operating System:  
    Boot files:        

sda4: __________________________________________________________________________

    File system:       Extended Partition
    Boot sector type:  -
    Boot sector info: 

sda5: __________________________________________________________________________

    File system:       ext4
    Boot sector type:  -
    Boot sector info: 
    Operating System:  Debian GNU/Linux 6.0
    Boot files:        /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img

sda6: __________________________________________________________________________

    File system:       ext4
    Boot sector type:  -
    Boot sector info: 
    Operating System:  
    Boot files:        

sda7: __________________________________________________________________________

    File system:       swap
    Boot sector type:  -
    Boot sector info: 

============================ Drive/Partition Info: =============================

Drive: sda _____________________________________________________________________

Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes

Partition  Boot  Start Sector    End Sector  # of Sectors  Id System

/dev/sda1    *          2,048       206,847       204,800   7 NTFS / exFAT / HPFS
/dev/sda2             206,848    97,731,687    97,524,840   7 NTFS / exFAT / HPFS
/dev/sda3          97,734,656   241,091,877   143,357,222   7 NTFS / exFAT / HPFS
/dev/sda4         241,092,606   274,292,735    33,200,130   5 Extended
/dev/sda5         241,092,608   260,622,335    19,529,728  83 Linux
/dev/sda6         260,624,384   270,387,199     9,762,816  83 Linux
/dev/sda7         270,389,248   274,292,735     3,903,488  82 Linux swap / Solaris


"blkid" output: ________________________________________________________________

Device           UUID                                   TYPE       LABEL

/dev/sda1        1084EF1984EF0058                       ntfs       System-reserviert
/dev/sda2        06C8F2E3C8F2D043                       ntfs       Systemplatte
/dev/sda3        8CCA3698CA367E90                       ntfs       Datenplatte
/dev/sda5        befea64b-6785-4e21-971c-2a1efa20af24   ext4       root-debian
/dev/sda6        47db9c6f-5215-4c73-92c1-4d1f04ecba85   ext4       home-debian
/dev/sda7        da5d371c-0bbc-4b34-a626-5d2127777982   swap       

================================ Mount points: =================================

Device           Mount_Point              Type       Options

/dev/sda5        /                        ext4       (rw,errors=remount-ro)
/dev/sda6        /home                    ext4       (rw)


=========================== sda5/boot/grub/grub.cfg: ===========================

--------------------------------------------------------------------------------
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#

### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
  load_env
fi
set default="2"
if [ "${prev_saved_entry}" ]; then
  set saved_entry="${prev_saved_entry}"
  save_env saved_entry
  set prev_saved_entry=
  save_env prev_saved_entry
  set boot_once=true
fi

function savedefault {
  if [ -z "${boot_once}" ]; then
    saved_entry="${chosen}"
    save_env saved_entry
  fi
}

function load_video {
  insmod vbe
  insmod vga
  insmod video_bochs
  insmod video_cirrus
}

insmod part_msdos
insmod ext2
set root='(hd0,msdos5)'
search --no-floppy --fs-uuid --set befea64b-6785-4e21-971c-2a1efa20af24
if loadfont /usr/share/grub/unicode.pf2 ; then
  set gfxmode=640x480
  load_video
  insmod gfxterm
fi
terminal_output gfxterm
insmod part_msdos
insmod ext2
set root='(hd0,msdos5)'
search --no-floppy --fs-uuid --set befea64b-6785-4e21-971c-2a1efa20af24
set locale_dir=($root)/boot/grub/locale
set lang=de
insmod gettext
set timeout=2
### END /etc/grub.d/00_header ###

### BEGIN /etc/grub.d/05_debian_theme ###
insmod part_msdos
insmod ext2
set root='(hd0,msdos5)'
search --no-floppy --fs-uuid --set befea64b-6785-4e21-971c-2a1efa20af24
insmod png
if background_image /usr/share/images/desktop-base/spacefun-grub.png; then
  set color_normal=light-gray/black
  set color_highlight=white/black
else
  set menu_color_normal=cyan/blue
  set menu_color_highlight=white/blue
fi
### END /etc/grub.d/05_debian_theme ###

### BEGIN /etc/grub.d/10_linux ###
menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os {
	insmod part_msdos
	insmod ext2
	set root='(hd0,msdos5)'
	search --no-floppy --fs-uuid --set befea64b-6785-4e21-971c-2a1efa20af24
	echo	'Loading Linux 2.6.32-5-amd64 ...'
	linux	/boot/vmlinuz-2.6.32-5-amd64 root=UUID=befea64b-6785-4e21-971c-2a1efa20af24 ro  quiet
	echo	'Loading initial ramdisk ...'
	initrd	/boot/initrd.img-2.6.32-5-amd64
}
menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64 (recovery mode)' --class debian --class gnu-linux --class gnu --class os {
	insmod part_msdos
	insmod ext2
	set root='(hd0,msdos5)'
	search --no-floppy --fs-uuid --set befea64b-6785-4e21-971c-2a1efa20af24
	echo	'Loading Linux 2.6.32-5-amd64 ...'
	linux	/boot/vmlinuz-2.6.32-5-amd64 root=UUID=befea64b-6785-4e21-971c-2a1efa20af24 ro single 
	echo	'Loading initial ramdisk ...'
	initrd	/boot/initrd.img-2.6.32-5-amd64
}
### END /etc/grub.d/10_linux ###

### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###

### BEGIN /etc/grub.d/30_os-prober ###
menuentry "Windows 7 (loader) (on /dev/sda1)" {
	insmod part_msdos
	insmod ntfs
	set root='(hd0,msdos1)'
	search --no-floppy --fs-uuid --set 1084ef1984ef0058
	chainloader +1
}
### END /etc/grub.d/30_os-prober ###

### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries.  Simply type the
# menu entries you want to add after this comment.  Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###

### BEGIN /etc/grub.d/41_custom ###
if [ -f  $prefix/custom.cfg ]; then
  source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
--------------------------------------------------------------------------------

=============================== sda5/etc/fstab: ================================

--------------------------------------------------------------------------------
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
proc            /proc           proc    defaults        0       0
# / was on /dev/sda5 during installation
UUID=befea64b-6785-4e21-971c-2a1efa20af24 /               ext4    errors=remount-ro 0       1
# /home was on /dev/sda6 during installation
UUID=47db9c6f-5215-4c73-92c1-4d1f04ecba85 /home           ext4    defaults        0       2
# swap was on /dev/sda7 during installation
UUID=da5d371c-0bbc-4b34-a626-5d2127777982 none            swap    sw              0       0
/dev/scd0       /media/cdrom0   udf,iso9660 user,noauto     0       0
--------------------------------------------------------------------------------

=================== sda5: Location of files loaded by Grub: ====================

           GiB - GB             File                                 Fragment(s)

            ?? = ??             boot/grub/core.img                             1
            ?? = ??             boot/grub/grub.cfg                             1
            ?? = ??             boot/initrd.img-2.6.32-5-amd64                 2
            ?? = ??             boot/vmlinuz-2.6.32-5-amd64                    1
            ?? = ??             initrd.img                                     2
            ?? = ??             vmlinuz                                        1
Sieht - zumindest für mich - ganz normal aus.

Beim Ablauf wurden allerdings folgende Hinweise ausgegeben :
Code: 
"gawk" could not be found, using "busybox awk" instead.
This may lead to unreliable results.

Danke für den Tip. Vielleicht sagt Dir der Output ja was.

Gruss H.
 
OP
H

halo44

Hacker
Guten Morgen Josef,

hier die gewünschten Ausgaben :
Code: 
fdisk -lu

Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x46f349d8

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *        2048      206847      102400    7  HPFS/NTFS
Partition 1 does not end on cylinder boundary.
/dev/sda2          206848    97731687    48762420    7  HPFS/NTFS
/dev/sda3        97734656   241091877    71678611    7  HPFS/NTFS
/dev/sda4       241092606   274292735    16600065    5  Extended
/dev/sda5       241092608   260622335     9764864   83  Linux
/dev/sda6       260624384   270387199     4881408   83  Linux
/dev/sda7       270389248   274292735     1951744   82  Linux swap / Solaris
Code: 
hwinfo --disk
26: IDE 00.0: 10600 Disk                                        
  [Created at block.243]
  UDI: /org/freedesktop/Hal/devices/storage_serial_ST3160815AS_6RX7435N
  Unique ID: 3OOL.ZTJinm5Ajh8
  Parent ID: vuMS.yBUmbKcHF17
  SysFS ID: /class/block/sda
  SysFS BusID: 0:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:0e.0/host0/target0:0:0/0:0:0:0
  Hardware Class: disk
  Model: "ST3160815AS"
  Device: "ST3160815AS"
  Revision: "4.AA"
  Serial ID: "6RX7435N"
  Driver: "ahci", "sd"
  Driver Modules: "ahci"
  Device File: /dev/sda
  Device Files: /dev/sda, /dev/block/8:0, /dev/disk/by-id/scsi-SATA_ST3160815AS_6RX7435N, /dev/disk/by-id/ata-ST3160815AS_6RX7435N, /dev/disk/by-path/pci-0000:00:0e.0-scsi-0:0:0:0
  Device Number: block 8:0-8:15
  BIOS id: 0x80
  Geometry (Logical): CHS 19457/255/63
  Size: 312581808 sectors a 512 bytes
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #22 (IDE interface)
Code: 
hwinfo --storage-ctrl
29: PCI 0e.0: 0101 IDE interface                                
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_10de_7f0
  Unique ID: vuMS.yBUmbKcHF17
  SysFS ID: /devices/pci0000:00/0000:00:0e.0
  SysFS BusID: 0000:00:0e.0
  Hardware Class: storage
  Model: "nVidia IDE interface"
  Vendor: pci 0x10de "nVidia Corporation"
  Device: pci 0x07f0 
  SubVendor: pci 0x1734 "Fujitsu Siemens Computers"
  SubDevice: pci 0x115b 
  Revision: 0xa2
  Driver: "ahci"
  Driver Modules: "ahci"
  I/O Ports: 0x1f0-0x1f7 (rw)
  I/O Port: 0x3f6 (rw)
  I/O Ports: 0x170-0x177 (rw)
  I/O Port: 0x376 (rw)
  I/O Ports: 0x30c0-0x30cf (rw)
  Memory Range: 0xfe384000-0xfe385fff (rw,non-prefetchable)
  IRQ: 27 (37355 events)
  Module Alias: "pci:v000010DEd000007F0sv00001734sd0000115Bbc01sc01i80"
  Driver Info #0:
    Driver Status: ahci is active
    Driver Activation Cmd: "modprobe ahci"
  Driver Info #1:
    Driver Status: ata_generic is active
    Driver Activation Cmd: "modprobe ata_generic"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
Danke für Dein Engagement.

Gruss H.

Nachtrag: ich sollte vielleicht noch erwähnen, daß vor der Installation von Debian die Partitionen 5 -7 für openSuse vorgesehen waren, d.h. sie standen zur Verfügung.
 
RME

RME

Advanced Hacker
...ich sehe auch nichts auffälliges aber ich denke noch immer dass etwas mit der Partitionstabelle nicht linux-conform ist. (was ist die "Geschichte" der Festplatte vor der aktuellen Windows-Installation?)

Anyway:

Missing Partitions in GParted schrieb:
Unfortunately, although libparted has many very useful features, it also has some bugs and limitations. Some of these motivated me to write my own partitioning tool for GUID Partition Table (GPT) disks, GPT fdisk. Another issue motivates this Web page: GParted sometimes claims that disks have no partitions, even though other tools, such as the Linux kernel and the fdisk utility, clearly see partitions on the disk. This problem has been cropping up a lot lately on Web forums.
Zum Vergrößern anklicken....
http://rodsbooks.com/missing-parts/

Damit solltest Du das Problem lösen können.

Gruss,
Roland
 
Jägerschlürfer

Jägerschlürfer

Moderator
Teammitglied
halo44 schrieb:
Code: 
fdisk -lu

Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x46f349d8

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *        2048      206847      102400    7  HPFS/NTFS
Partition 1 does not end on cylinder boundary.
/dev/sda2          206848    97731687    48762420    7  HPFS/NTFS
/dev/sda3        97734656   241091877    71678611    7  HPFS/NTFS
/dev/sda4       241092606   274292735    16600065    5  Extended
/dev/sda5       241092608   260622335     9764864   83  Linux
/dev/sda6       260624384   270387199     4881408   83  Linux
/dev/sda7       270389248   274292735     1951744   82  Linux swap / Solaris
Zum Vergrößern anklicken....
das stört mich etwas,...
Partition 1 does not end on cylinder boundary.
 
J

josef-wien

Ultimate Guru
Gib bei der Installation den Boot-Parameter noapic ein bzw. versuche eine der Möglichkeiten bei der Funktionstaste für "Kernel Default".

Ich denke, daß die Partitionentabelle nicht das Problem ist, schließlich läuft Debian (mit dem schon relativ alten Kernel) problemlos.

Jägerschlürfer schrieb:
das stört mich etwas
Zum Vergrößern anklicken....
Mich nicht, das "Anlehnen" an Zylindergrenzen ist Schnee von gestern.
 
OP
H

halo44

Hacker
josef-wien schrieb:
... Ich denke, daß die Partitionentabelle nicht das Problem ist, schließlich läuft Debian (mit dem schon relativ alten Kernel) problemlos ...
Zum Vergrößern anklicken....

Das glaube ich auch nicht, da CD/DVD und Festplatte nicht erkannt werden. Wobei die versuchte Installation ja zunächst von der CD/DVD anläuft.

Es muß etwas mit S ATA, womit ja beide Geräte arbeiten, zu tun haben. Aber da begebe ich mich auf glattes Eis.

josef-wien schrieb:
... Gib bei der Installation den Boot-Parameter noapic ein bzw. versuche eine der Möglichkeiten bei der Funktionstaste für "Kernel Default" ...
Zum Vergrößern anklicken....

Obwohl ich sicher bin, daß ich noapic und auch sichere Einstellungen schon versucht habe, werde ich dies morgen nochmal tun. Nolapic kenne ich von meinem Desktoprechner, wo ich diese Option immer wählen muß. Die benötigt aber der Rechner meiner Frau nicht.

Auch dem Tip von Roland werde ich auf jeden Fall noch mal nachgehen.

Gruss H.
 
RME

RME

Advanced Hacker
josef-wien schrieb:
... Ich denke, daß die Partitionentabelle nicht das Problem ist, schließlich läuft Debian (mit dem schon relativ alten Kernel) problemlos ...
Zum Vergrößern anklicken....
Das glaube ich auch nicht, da CD/DVD und Festplatte nicht erkannt werden. Wobei die versuchte Installation ja zunächst von der CD/DVD anläuft.
Zum Vergrößern anklicken....
...scheint logisch.

Kannst Du mal nachschauen wie im BIOS SATA konfiguriert ist?

Bei mir:
Code: 
BIOS >>> Main
Storage configuration
SATA configuration         [Enhanced]
  Configure SATA as        [IDE]
Wenn bei Dir "Configure SATA as [AHCI]" dann mal [IDE] testen.

Refs.:

SATA disks as AHCI
http://fedoraforum.org/forum/showthread.php?t=202286

Advanced Host Controller Interface
http://de.wikipedia.org/wiki/Advanced_Host_Controller_Interface
http://en.wikipedia.org/wiki/Advanced_Host_Controller_Interface
 
OP
H

halo44

Hacker
Guten Morgen Roland,

zunächst ein Nachtrag, da ich vergessen habe Dir Deine Frage zu beantworten :

was ist die "Geschichte" der Festplatte vor der aktuellen Windows-Installation?
Zum Vergrößern anklicken....

Der Rechner wurde im Januar 2009 mit installiertem Windows XP Professional gekauft und im Dezember 2009 auf Windows 7 Home Premium umgestellt.

Jetzt zum BIOS :

Unter Advanced / Peripheral Configuration / SATA Controller Mode ist eingestellt Compatible.

Compatible mode: Sata and pata drives are auto-detected and placed in Legacy mode
Zum Vergrößern anklicken....

Alternative Einstellung wäre Enhanced :

Enhanced (none-AHCI) mode: Sata and pata drives are auto-detected and placed in Native IDE mode
Zum Vergrößern anklicken....

Ein Wechsel kann (auch laut Deinen beigefügten Links) für Windows ordentlich "in die Hose gehen". Bevor ich diese Maßnahme ergreife, bräuchte ich noch etwas Zuspruch :/

Gruss H.
 
J

josef-wien

Ultimate Guru
halo44 schrieb:
Enhanced (none-AHCI) mode
Zum Vergrößern anklicken....
Von der reinen Lehre her ist das die schlechtere Lösung, aber solange Du Windows nicht mit dieser Einstellung startest, kann nichts passieren.

halo44 schrieb:
Nach dem Start von Debian und/oder dem Start eines OS von externer Festplatte bzw. USB-Stick?
Zum Vergrößern anklicken....
Vor allem letzteres ist interessant, da hier ja der Controller nicht korrekt erkannt wird.
 
RME

RME

Advanced Hacker
Ein Wechsel kann (auch laut Deinen beigefügten Links) für Windows ordentlich "in die Hose gehen". Bevor ich diese Maßnahme ergreife, bräuchte ich noch etwas Zuspruch
Zum Vergrößern anklicken....
...ich würde dies vorerst (testweise) nur für die openSUSE Installation so setzen, nachher wieder so wie's war.
 
OP
H

halo44

Hacker
Hier zunächst einmal die Ausgabe von dmesg nach Booten von einer externen Festplatte :
Code: 
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.0-15-generic (buildd@crested) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #26-Ubuntu SMP Fri Jan 20 17:23:00 UTC 2012 (Ubuntu 3.0.0-15.26-generic 3.0.13)
[    0.000000] Command line: root=UUID=f1f4562c-32fb-466a-951f-114c5bddf6df ro quiet splash 
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[    0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bffe0000 (usable)
[    0.000000]  BIOS-e820: 00000000bffe0000 - 00000000bffe4000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bffe4000 - 00000000bffe5000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bffe5000 - 00000000d0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000d0000000 - 00000000dff00000 (usable)
[    0.000000]  BIOS-e820: 00000000dff00000 - 00000000e0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI present.
[    0.000000] DMI: FUJITSU SIEMENS ESPRIMO EDITION P2530         /D2740-A2, BIOS 6.00 R1.02.2740.A2               05/09/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x120000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-through
[    0.000000]   C8000-DFFFF uncachable
[    0.000000]   E0000-FFFFF write-through
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0E0000000 mask FE0000000 uncachable
[    0.000000]   1 base 000000000 mask F00000000 write-back
[    0.000000]   2 base 100000000 mask FE0000000 write-back
[    0.000000]   3 base 0C0000000 mask FFFF00000 uncachable
[    0.000000]   4 base 0C0000000 mask FF0000000 uncachable
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] original variable MTRRs
[    0.000000] reg 0, base: 3584MB, range: 512MB, type UC
[    0.000000] reg 1, base: 0GB, range: 4GB, type WB
[    0.000000] reg 2, base: 4GB, range: 512MB, type WB
[    0.000000] reg 3, base: 3GB, range: 1MB, type UC
[    0.000000] reg 4, base: 3GB, range: 256MB, type UC
[    0.000000] total RAM covered: 3840M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K 	chunk_size: 64K 	num_reg: 4  	lose cover RAM: 0G
[    0.000000] New variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2GB, range: 1GB, type WB
[    0.000000] reg 2, base: 3328MB, range: 256MB, type WB
[    0.000000] reg 3, base: 4GB, range: 512MB, type WB
[    0.000000] e820 update range: 00000000c0000000 - 00000000d0000000 (usable) ==> (reserved)
[    0.000000] e820 update range: 00000000e0000000 - 0000000100000000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0xdff00 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000f8340] f8340
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000dff00000
[    0.000000]  0000000000 - 00dfe00000 page 2M
[    0.000000]  00dfe00000 - 00dff00000 page 4k
[    0.000000] kernel direct mapping tables up to dff00000 @ 1fffa000-20000000
[    0.000000] init_memory_mapping: 0000000100000000-0000000120000000
[    0.000000]  0100000000 - 0120000000 page 2M
[    0.000000] kernel direct mapping tables up to 120000000 @ dfefa000-dff00000
[    0.000000] RAMDISK: 36ce9000 - 37ff0000
[    0.000000] ACPI: RSDP 00000000000f8310 00014 (v00 PTLTD )
[    0.000000] ACPI: RSDT 00000000bffe19c1 0004C (v01 FSC    PC       00060000  LTP 00000000)
[    0.000000] ACPI: FACP 00000000bffe3a66 00074 (v01 FSC             00060000      000F4240)
[    0.000000] ACPI: DSDT 00000000bffe1a0d 02059 (v01 FSC    D2740/A1 00060000 MSFT 03000001)
[    0.000000] ACPI: FACS 00000000bffe4fc0 00040
[    0.000000] ACPI: SSDT 00000000bffe3ada 0007A (v01 FSC    CST_CPU0 00060000  CSF 00000001)
[    0.000000] ACPI: SSDT 00000000bffe3b54 0007A (v01 FSC    CST_CPU1 00060000  CSF 00000001)
[    0.000000] ACPI: SSDT 00000000bffe3bce 000D7 (v01 FSC    PST_CPU0 00060000  CSF 00000001)
[    0.000000] ACPI: SSDT 00000000bffe3ca5 000D7 (v01 FSC    PST_CPU1 00060000  CSF 00000001)
[    0.000000] ACPI: SLIC 00000000bffe3d7c 00176 (v01 FSC    PC       00060000  LTP 00000000)
[    0.000000] ACPI: MCFG 00000000bffe3ef2 0003C (v01 PTLTD    MCFG   00060000  LTP 00000000)
[    0.000000] ACPI: HPET 00000000bffe3f2e 00038 (v01 PTLTD  HPETTBL  00060000  LTP 00000001)
[    0.000000] ACPI: APIC 00000000bffe3f66 00072 (v01 PTLTD  ? APIC   00060000  LTP 00000000)
[    0.000000] ACPI: BOOT 00000000bffe3fd8 00028 (v01 PTLTD  $SBFTBL$ 00060000  LTP 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000120000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000120000000
[    0.000000]   NODE_DATA [000000011fffb000 - 000000011fffffff]
[    0.000000]  [ffffea0000000000-ffffea0003ffffff] PMD -> [ffff88011ba00000-ffff88011f1fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00120000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009d
[    0.000000]     0: 0x00000100 -> 0x000bffe0
[    0.000000]     0: 0x000d0000 -> 0x000dff00
[    0.000000]     0: 0x00100000 -> 0x00120000
[    0.000000] On node 0 totalpages: 982637
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3920 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 833304 pages, LIFO batch:31
[    0.000000]   Normal zone: 1792 pages used for memmap
[    0.000000]   Normal zone: 129280 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[    0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bffe0000 - 00000000bffe4000
[    0.000000] PM: Registered nosave memory: 00000000bffe4000 - 00000000bffe5000
[    0.000000] PM: Registered nosave memory: 00000000bffe5000 - 00000000d0000000
[    0.000000] PM: Registered nosave memory: 00000000dff00000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f8000000
[    0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[    0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[    0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000fff00000
[    0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88011fc00000 s79616 r8192 d22784 u1048576
[    0.000000] pcpu-alloc: s79616 r8192 d22784 u1048576 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 966504
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=UUID=f1f4562c-32fb-466a-951f-114c5bddf6df ro quiet splash 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3771908k/4718592k available (6136k kernel code, 788044k absent, 158640k reserved, 6898k data, 988k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:16640 nr_irqs:512 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 31457280 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2199.674 MHz processor.
[    0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4399.34 BogoMIPS (lpj=8798696)
[    0.004010] pid_max: default: 32768 minimum: 301
[    0.004044] Security Framework initialized
[    0.004065] AppArmor: AppArmor initialized
[    0.004067] Yama: becoming mindful.
[    0.004564] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.009193] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.010402] Mount-cache hash table entries: 256
[    0.010590] Initializing cgroup subsys cpuacct
[    0.010598] Initializing cgroup subsys memory
[    0.010609] Initializing cgroup subsys devices
[    0.010612] Initializing cgroup subsys freezer
[    0.010614] Initializing cgroup subsys net_cls
[    0.010616] Initializing cgroup subsys blkio
[    0.010624] Initializing cgroup subsys perf_event
[    0.010659] CPU: Physical Processor ID: 0
[    0.010661] CPU: Processor Core ID: 0
[    0.010664] mce: CPU supports 6 MCE banks
[    0.010674] CPU0: Thermal monitoring enabled (TM2)
[    0.010679] using mwait in idle threads.
[    0.013221] ACPI: Core revision 20110413
[    0.016047] ftrace: allocating 25728 entries in 101 pages
[    0.020543] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.061905] CPU0: Intel(R) Pentium(R) Dual  CPU  E2200  @ 2.20GHz stepping 0d
[    0.064003] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[    0.064003] PEBS disabled due to CPU errata.
[    0.064003] ... version:                2
[    0.064003] ... bit width:              40
[    0.064003] ... generic registers:      2
[    0.064003] ... value mask:             000000ffffffffff
[    0.064003] ... max period:             000000007fffffff
[    0.064003] ... fixed-purpose events:   3
[    0.064003] ... event mask:             0000000700000003
[    0.064003] Booting Node   0, Processors  #1 Ok.
[    0.064003] smpboot cpu 1: start_ip = 98000
[    0.152029] Brought up 2 CPUs
[    0.152032] Total of 2 processors activated (8799.22 BogoMIPS).
[    0.152730] devtmpfs: initialized
[    0.152730] PM: Registering ACPI NVS region at bffe4000 (4096 bytes)
[    0.153415] print_constraints: dummy: 
[    0.153450] Time: 16:54:59  Date: 10/25/12
[    0.153490] NET: Registered protocol family 16
[    0.153532] Trying to unpack rootfs image as initramfs...
[    0.153649] ACPI: bus type pci registered
[    0.153718] PCI: MMCONFIG for domain 0000 [bus 00-04] at [mem 0xf8000000-0xf84fffff] (base 0xf8000000)
[    0.153721] PCI: MMCONFIG at [mem 0xf8000000-0xf84fffff] reserved in E820
[    0.154775] PCI: Using configuration type 1 for base access
[    0.156771] bio: create slab <bio-0> at 0
[    0.157500] ACPI: EC: Look up EC in DSDT
[    0.159285] ACPI: Interpreter enabled
[    0.159289] ACPI: (supports S0 S1 S3 S4 S5)
[    0.159308] ACPI: Using IOAPIC for interrupt routing
[    0.162333] ACPI: No dock devices found.
[    0.162340] HEST: Table not found.
[    0.162344] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.162398] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.162486] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.162489] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.162492] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.162494] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff]
[    0.162497] pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xfebfffff]
[    0.162500] pci_root PNP0A08:00: host bridge window [mem 0xfed00000-0xfedfffff]
[    0.162521] pci 0000:00:00.0: [10de:07c1] type 0 class 0x000600
[    0.162623] pci 0000:00:00.1: [10de:07cb] type 0 class 0x000500
[    0.162772] pci 0000:00:01.0: [10de:07cd] type 0 class 0x000500
[    0.162916] pci 0000:00:01.1: [10de:07ce] type 0 class 0x000500
[    0.163057] pci 0000:00:01.2: [10de:07cf] type 0 class 0x000500
[    0.163200] pci 0000:00:01.3: [10de:07d0] type 0 class 0x000500
[    0.163343] pci 0000:00:01.4: [10de:07d1] type 0 class 0x000500
[    0.163485] pci 0000:00:01.5: [10de:07d2] type 0 class 0x000500
[    0.163638] pci 0000:00:01.6: [10de:07d3] type 0 class 0x000500
[    0.163781] pci 0000:00:02.0: [10de:07d6] type 0 class 0x000500
[    0.163927] pci 0000:00:03.0: [10de:07d7] type 0 class 0x000601
[    0.163985] pci 0000:00:03.1: [10de:07d8] type 0 class 0x000c05
[    0.164023] pci 0000:00:03.1: reg 10: [io  0x3080-0x30bf]
[    0.164048] pci 0000:00:03.1: reg 20: [io  0x3040-0x307f]
[    0.164056] pci 0000:00:03.1: reg 24: [io  0x3000-0x303f]
[    0.164083] pci 0000:00:03.1: PME# supported from D3hot D3cold
[    0.164089] pci 0000:00:03.1: PME# disabled
[    0.164125] pci 0000:00:03.4: [10de:07c8] type 0 class 0x000500
[    0.164271] pci 0000:00:04.0: [10de:07fe] type 0 class 0x000c03
[    0.164284] pci 0000:00:04.0: reg 10: [mem 0xfe306000-0xfe306fff]
[    0.164331] pci 0000:00:04.0: supports D1 D2
[    0.164333] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.164337] pci 0000:00:04.0: PME# disabled
[    0.164353] pci 0000:00:04.1: [10de:056a] type 0 class 0x000c03
[    0.164368] pci 0000:00:04.1: reg 10: [mem 0xfe308000-0xfe3080ff]
[    0.164422] pci 0000:00:04.1: supports D1 D2
[    0.164424] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.164428] pci 0000:00:04.1: PME# disabled
[    0.164461] pci 0000:00:09.0: [10de:07fc] type 0 class 0x000403
[    0.164475] pci 0000:00:09.0: reg 10: [mem 0xfe300000-0xfe303fff]
[    0.164525] pci 0000:00:09.0: PME# supported from D3hot D3cold
[    0.164529] pci 0000:00:09.0: PME# disabled
[    0.164548] pci 0000:00:0a.0: [10de:056d] type 1 class 0x000604
[    0.164596] pci 0000:00:0b.0: [10de:056e] type 1 class 0x000604
[    0.164631] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.164635] pci 0000:00:0b.0: PME# disabled
[    0.164653] pci 0000:00:0c.0: [10de:056f] type 1 class 0x000604
[    0.164692] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.164695] pci 0000:00:0c.0: PME# disabled
[    0.164716] pci 0000:00:0d.0: [10de:056f] type 1 class 0x000604
[    0.164751] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.164754] pci 0000:00:0d.0: PME# disabled
[    0.164772] pci 0000:00:0e.0: [10de:07f0] type 0 class 0x000101
[    0.164803] pci 0000:00:0e.0: reg 20: [io  0x30c0-0x30cf]
[    0.164810] pci 0000:00:0e.0: reg 24: [mem 0xfe304000-0xfe305fff]
[    0.164847] pci 0000:00:0f.0: [10de:07dc] type 0 class 0x000200
[    0.164859] pci 0000:00:0f.0: reg 10: [mem 0xfe307000-0xfe307fff]
[    0.164866] pci 0000:00:0f.0: reg 14: [io  0x30d0-0x30d7]
[    0.164873] pci 0000:00:0f.0: reg 18: [mem 0xfe308800-0xfe3088ff]
[    0.164880] pci 0000:00:0f.0: reg 1c: [mem 0xfe308400-0xfe30840f]
[    0.164913] pci 0000:00:0f.0: supports D1 D2
[    0.164915] pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.164920] pci 0000:00:0f.0: PME# disabled
[    0.164935] pci 0000:00:10.0: [10de:07e1] type 0 class 0x000300
[    0.164946] pci 0000:00:10.0: reg 10: [mem 0xfd000000-0xfdffffff]
[    0.164956] pci 0000:00:10.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.164965] pci 0000:00:10.0: reg 1c: [mem 0xfc000000-0xfcffffff 64bit]
[    0.164976] pci 0000:00:10.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.165049] pci 0000:01:07.0: [1244:0e00] type 0 class 0x000280
[    0.165066] pci 0000:01:07.0: reg 10: [mem 0xfe000000-0xfe00001f]
[    0.165075] pci 0000:01:07.0: reg 14: [io  0x4000-0x401f]
[    0.165131] pci 0000:01:07.0: supports D2
[    0.165133] pci 0000:01:07.0: PME# supported from D2 D3hot D3cold
[    0.165138] pci 0000:01:07.0: PME# disabled
[    0.165174] pci 0000:00:0a.0: PCI bridge to [bus 01-01] (subtractive decode)
[    0.165179] pci 0000:00:0a.0:   bridge window [io  0x4000-0x4fff]
[    0.165183] pci 0000:00:0a.0:   bridge window [mem 0xfe000000-0xfe0fffff]
[    0.165187] pci 0000:00:0a.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.165191] pci 0000:00:0a.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.165194] pci 0000:00:0a.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.165197] pci 0000:00:0a.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.165200] pci 0000:00:0a.0:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.165203] pci 0000:00:0a.0:   bridge window [mem 0xe0000000-0xfebfffff] (subtractive decode)
[    0.165206] pci 0000:00:0a.0:   bridge window [mem 0xfed00000-0xfedfffff] (subtractive decode)
[    0.165238] pci 0000:00:0b.0: PCI bridge to [bus 02-02]
[    0.165242] pci 0000:00:0b.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.165246] pci 0000:00:0b.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.165251] pci 0000:00:0b.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.165283] pci 0000:00:0c.0: PCI bridge to [bus 03-03]
[    0.165288] pci 0000:00:0c.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.165292] pci 0000:00:0c.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.165297] pci 0000:00:0c.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.165328] pci 0000:00:0d.0: PCI bridge to [bus 04-04]
[    0.165332] pci 0000:00:0d.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.165336] pci 0000:00:0d.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.165341] pci 0000:00:0d.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.165358] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.165402] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXA._PRT]
[    0.165422] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.165478]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.165481]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.165483] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.168529] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 10 *11 14 15)
[    0.168604] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.168674] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.168743] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.168813] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.168882] ACPI: PCI Interrupt Link [LNKF] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.168952] ACPI: PCI Interrupt Link [LNKG] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.169022] ACPI: PCI Interrupt Link [LNKH] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.169092] ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *5
[    0.169181] ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *10
[    0.169259] ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *11
[    0.169328] ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11
[    0.169397] ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *11
[    0.169467] ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.169541] ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.169611] ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[    0.169681] ACPI: PCI Interrupt Link [LNKQ] (IRQs 16 17 18 19 20 21 22 23) *11
[    0.169759] ACPI: PCI Interrupt Link [LNKR] (IRQs 16 17 18 19 20 21 22 23) *0
[    0.169917] vgaarb: device added: PCI:0000:00:10.0,decodes=io+mem,owns=io+mem,locks=none
[    0.169920] vgaarb: loaded
[    0.169922] vgaarb: bridge control possible 0000:00:10.0
[    0.170132] SCSI subsystem initialized
[    0.170229] libata version 3.00 loaded.
[    0.170278] usbcore: registered new interface driver usbfs
[    0.170289] usbcore: registered new interface driver hub
[    0.170319] usbcore: registered new device driver usb
[    0.170424] PCI: Using ACPI for IRQ routing
[    0.170431] PCI: pci_cache_line_size set to 64 bytes
[    0.170549] reserve RAM buffer: 000000000009dc00 - 000000000009ffff 
[    0.170552] reserve RAM buffer: 00000000bffe0000 - 00000000bfffffff 
[    0.170555] reserve RAM buffer: 00000000dff00000 - 00000000dfffffff 
[    0.170663] NetLabel: Initializing
[    0.170665] NetLabel:  domain hash size = 128
[    0.170666] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.170679] NetLabel:  unlabeled traffic allowed by default
[    0.170725] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.170732] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    0.170737] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    0.176359] Switching to clocksource hpet
[    0.179322] Switched to NOHz mode on CPU #0
[    0.179373] Switched to NOHz mode on CPU #1
[    0.184349] AppArmor: AppArmor Filesystem Enabled
[    0.184392] pnp: PnP ACPI init
[    0.184415] ACPI: bus type pnp registered
[    0.184512] pnp 00:00: [bus 00-ff]
[    0.184516] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.184518] pnp 00:00: [io  0x0d00-0xffff window]
[    0.184520] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.184523] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.184525] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[    0.184527] pnp 00:00: [mem 0xe0000000-0xfebfffff window]
[    0.184529] pnp 00:00: [mem 0xfed00000-0xfedfffff window]
[    0.184588] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.184820] pnp 00:01: [io  0x0010-0x001f]
[    0.184822] pnp 00:01: [io  0x0022-0x002d]
[    0.184824] pnp 00:01: [io  0x0030-0x003f]
[    0.184826] pnp 00:01: [io  0x0050-0x0053]
[    0.184828] pnp 00:01: [io  0x0060]
[    0.184830] pnp 00:01: [io  0x0062-0x0063]
[    0.184832] pnp 00:01: [io  0x0064]
[    0.184838] pnp 00:01: [io  0x0065-0x006f]
[    0.184840] pnp 00:01: [io  0x0074-0x007f]
[    0.184842] pnp 00:01: [io  0x0090-0x009f]
[    0.184844] pnp 00:01: [io  0x00a2-0x00b1]
[    0.184846] pnp 00:01: [io  0x00b2-0x00b3]
[    0.184847] pnp 00:01: [io  0x00b4-0x00bf]
[    0.184849] pnp 00:01: [io  0x00ec-0x00ef]
[    0.184851] pnp 00:01: [io  0x0072-0x0073]
[    0.184853] pnp 00:01: [io  0x004e-0x004f]
[    0.184855] pnp 00:01: [io  0x04d0-0x04d1]
[    0.184856] pnp 00:01: [io  0x0810]
[    0.184858] pnp 00:01: [io  0x1000-0x10e7]
[    0.184860] pnp 00:01: [io  0x1400-0x14fe]
[    0.184862] pnp 00:01: [io  0x1800-0x18fe]
[    0.184864] pnp 00:01: [io  0x1900-0x19fe]
[    0.184866] pnp 00:01: [io  0x1a00-0x1afe]
[    0.184867] pnp 00:01: [io  0x1b00-0x1b0e]
[    0.184869] pnp 00:01: [io  0x1c00-0x1cfe]
[    0.184871] pnp 00:01: [io  0xfe00]
[    0.184873] pnp 00:01: [io  0xff00]
[    0.184875] pnp 00:01: [mem 0xf8000000-0xfbffffff]
[    0.184877] pnp 00:01: [mem 0xfec00000-0xfecfffff]
[    0.184879] pnp 00:01: [mem 0xfee00000-0xfeefffff]
[    0.184881] pnp 00:01: [mem 0xfef80000-0xfef80fff]
[    0.184982] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.184985] system 00:01: [io  0x0810] has been reserved
[    0.184988] system 00:01: [io  0x1000-0x10e7] has been reserved
[    0.184991] system 00:01: [io  0x1400-0x14fe] has been reserved
[    0.184993] system 00:01: [io  0x1800-0x18fe] has been reserved
[    0.184996] system 00:01: [io  0x1900-0x19fe] has been reserved
[    0.184998] system 00:01: [io  0x1a00-0x1afe] has been reserved
[    0.185001] system 00:01: [io  0x1b00-0x1b0e] has been reserved
[    0.185003] system 00:01: [io  0x1c00-0x1cfe] has been reserved
[    0.185006] system 00:01: [io  0xfe00] has been reserved
[    0.185009] system 00:01: [io  0xff00] has been reserved
[    0.185012] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.185015] system 00:01: [mem 0xfec00000-0xfecfffff] could not be reserved
[    0.185018] system 00:01: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.185021] system 00:01: [mem 0xfef80000-0xfef80fff] has been reserved
[    0.185024] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.185036] pnp 00:02: [io  0x0000-0x000f]
[    0.185037] pnp 00:02: [io  0x0080-0x008f]
[    0.185039] pnp 00:02: [io  0x00c0-0x00df]
[    0.185042] pnp 00:02: [dma 4]
[    0.185077] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.185091] pnp 00:03: [io  0x0070-0x0071]
[    0.185113] pnp 00:03: [irq 8]
[    0.185147] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.185161] pnp 00:04: [io  0x00f0-0x00fe]
[    0.185167] pnp 00:04: [irq 13]
[    0.185201] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.185214] pnp 00:05: [io  0x0061]
[    0.185250] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.185299] pnp 00:06: [mem 0xfed00000-0xfed00fff]
[    0.185335] pnp 00:06: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.185399] pnp 00:07: [io  0x03f0-0x03f5]
[    0.185402] pnp 00:07: [io  0x03f7]
[    0.185404] pnp 00:07: [dma 2]
[    0.185410] pnp 00:07: [irq 6]
[    0.185464] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.185605] pnp 00:08: [io  0x03f8-0x03ff]
[    0.185611] pnp 00:08: [irq 4]
[    0.185671] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.185677] pnp: PnP ACPI: found 9 devices
[    0.185678] ACPI: ACPI bus type pnp unregistered
[    0.191767] PCI: max bus depth: 1 pci_try_num: 2
[    0.191812] pci 0000:00:10.0: BAR 6: assigned [mem 0xf0000000-0xf001ffff pref]
[    0.191816] pci 0000:00:0a.0: PCI bridge to [bus 01-01]
[    0.191819] pci 0000:00:0a.0:   bridge window [io  0x4000-0x4fff]
[    0.191824] pci 0000:00:0a.0:   bridge window [mem 0xfe000000-0xfe0fffff]
[    0.191827] pci 0000:00:0a.0:   bridge window [mem pref disabled]
[    0.191833] pci 0000:00:0b.0: PCI bridge to [bus 02-02]
[    0.191835] pci 0000:00:0b.0:   bridge window [io  disabled]
[    0.191839] pci 0000:00:0b.0:   bridge window [mem disabled]
[    0.191842] pci 0000:00:0b.0:   bridge window [mem pref disabled]
[    0.191846] pci 0000:00:0c.0: PCI bridge to [bus 03-03]
[    0.191848] pci 0000:00:0c.0:   bridge window [io  disabled]
[    0.191852] pci 0000:00:0c.0:   bridge window [mem disabled]
[    0.191855] pci 0000:00:0c.0:   bridge window [mem pref disabled]
[    0.191860] pci 0000:00:0d.0: PCI bridge to [bus 04-04]
[    0.191862] pci 0000:00:0d.0:   bridge window [io  disabled]
[    0.191866] pci 0000:00:0d.0:   bridge window [mem disabled]
[    0.191869] pci 0000:00:0d.0:   bridge window [mem pref disabled]
[    0.191881] pci 0000:00:0a.0: setting latency timer to 64
[    0.191887] pci 0000:00:0b.0: setting latency timer to 64
[    0.191893] pci 0000:00:0c.0: setting latency timer to 64
[    0.191898] pci 0000:00:0d.0: setting latency timer to 64
[    0.191902] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.191904] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.191906] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.191909] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.191911] pci_bus 0000:00: resource 8 [mem 0xe0000000-0xfebfffff]
[    0.191913] pci_bus 0000:00: resource 9 [mem 0xfed00000-0xfedfffff]
[    0.191916] pci_bus 0000:01: resource 0 [io  0x4000-0x4fff]
[    0.191918] pci_bus 0000:01: resource 1 [mem 0xfe000000-0xfe0fffff]
[    0.191921] pci_bus 0000:01: resource 4 [io  0x0000-0x0cf7]
[    0.191923] pci_bus 0000:01: resource 5 [io  0x0d00-0xffff]
[    0.191925] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[    0.191927] pci_bus 0000:01: resource 7 [mem 0x000c0000-0x000dffff]
[    0.191930] pci_bus 0000:01: resource 8 [mem 0xe0000000-0xfebfffff]
[    0.191932] pci_bus 0000:01: resource 9 [mem 0xfed00000-0xfedfffff]
[    0.191995] NET: Registered protocol family 2
[    0.192213] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.194059] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.200052] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.200791] TCP: Hash tables configured (established 524288 bind 65536)
[    0.200798] TCP reno registered
[    0.200829] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.200878] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.201070] NET: Registered protocol family 1
[    0.256161] pci 0000:00:10.0: Boot video device
[    0.256168] PCI: CLS 64 bytes, default 64
[    0.256172] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.256175] Placing 64MB software IO TLB between ffff8800dbefa000 - ffff8800dfefa000
[    0.256177] software IO TLB at phys 0xdbefa000 - 0xdfefa000
[    0.256204] Simple Boot Flag at 0x3b set to 0x1
[    0.256573] audit: initializing netlink socket (disabled)
[    0.256586] type=2000 audit(1351184098.252:1): initialized
[    0.292882] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.325836] VFS: Disk quotas dquot_6.5.2
[    0.325902] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.326538] fuse init (API version 7.16)
[    0.326632] msgmni has been set to 7367
[    0.327033] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.327070] io scheduler noop registered
[    0.327072] io scheduler deadline registered
[    0.327117] io scheduler cfq registered (default)
[    0.327260] pcieport 0000:00:0b.0: setting latency timer to 64
[    0.327301] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
[    0.327355] pcieport 0000:00:0c.0: setting latency timer to 64
[    0.327386] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
[    0.327433] pcieport 0000:00:0d.0: setting latency timer to 64
[    0.327465] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
[    0.327533] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.327556] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.327607] intel_idle: MWAIT substates: 0x220
[    0.327609] intel_idle: does not run on family 6 model 15
[    0.327691] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.327699] ACPI: Power Button [PWRB]
[    0.327758] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.327762] ACPI: Power Button [PWRF]
[    0.327792] ACPI: acpi_idle registered with cpuidle
[    0.327829] Marking TSC unstable due to TSC halts in idle
[    0.328754] ERST: Table is not found!
[    0.328860] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.349260] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.564077] Freeing initrd memory: 19484k freed
[    0.644643] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.644984] Linux agpgart interface v0.103
[    0.646083] brd: module loaded
[    0.646595] loop: module loaded
[    0.646827] pata_acpi 0000:00:0e.0: setting latency timer to 64
[    0.647116] Fixed MDIO Bus: probed
[    0.647138] PPP generic driver version 2.4.2
[    0.647188] tun: Universal TUN/TAP device driver, 1.6
[    0.647189] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.647269] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.647429] ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 23
[    0.647447] ehci_hcd 0000:00:04.1: PCI INT B -> Link[LNKI] -> GSI 23 (level, high) -> IRQ 23
[    0.647474] ehci_hcd 0000:00:04.1: setting latency timer to 64
[    0.647478] ehci_hcd 0000:00:04.1: EHCI Host Controller
[    0.647518] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[    0.647548] ehci_hcd 0000:00:04.1: debug port 1
[    0.647557] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[    0.647577] ehci_hcd 0000:00:04.1: irq 23, io mem 0xfe308000
[    0.656032] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[    0.656185] hub 1-0:1.0: USB hub found
[    0.656190] hub 1-0:1.0: 10 ports detected
[    0.656272] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.656405] ACPI: PCI Interrupt Link [LNKJ] enabled at IRQ 22
[    0.656417] ohci_hcd 0000:00:04.0: PCI INT A -> Link[LNKJ] -> GSI 22 (level, high) -> IRQ 22
[    0.656431] ohci_hcd 0000:00:04.0: setting latency timer to 64
[    0.656434] ohci_hcd 0000:00:04.0: OHCI Host Controller
[    0.656477] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[    0.656502] ohci_hcd 0000:00:04.0: irq 22, io mem 0xfe306000
[    0.714110] hub 2-0:1.0: USB hub found
[    0.714115] hub 2-0:1.0: 10 ports detected
[    0.714187] uhci_hcd: USB Universal Host Controller Interface driver
[    0.714260] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.717158] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.717166] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.717286] mousedev: PS/2 mouse device common for all mice
[    0.717407] rtc_cmos 00:03: RTC can wake from S4
[    0.717530] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.717564] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.717667] device-mapper: uevent: version 1.0.3
[    0.717745] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    0.717795] cpuidle: using governor ladder
[    0.717862] cpuidle: using governor menu
[    0.717865] EFI Variables Facility v0.08 2004-May-17
[    0.718116] TCP cubic registered
[    0.718238] NET: Registered protocol family 10
[    0.718708] NET: Registered protocol family 17
[    0.718730] Registering the dns_resolver key type
[    0.718828] PM: Hibernation image not present or could not be loaded.
[    0.718844] registered taskstats version 1
[    0.738607]   Magic number: 0:492:945
[    0.738655] tty tty2: hash matches
[    0.738726] rtc_cmos 00:03: setting system clock to 2012-10-25 16:55:00 UTC (1351184100)
[    0.738770] P-state transition latency capped at 20 uS
[    0.738851] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.738853] EDD information not available.
[    0.740720] Freeing unused kernel memory: 988k freed
[    0.741094] Write protecting the kernel read-only data: 12288k
[    0.748323] Freeing unused kernel memory: 2036k freed
[    0.754730] Freeing unused kernel memory: 1388k freed
[    0.778912] udevd[81]: starting version 173
[    0.854905] ahci 0000:00:0e.0: version 3.0
[    0.854951] ahci 0000:00:0e.0: controller can do NCQ, turning on CAP_NCQ
[    0.854953] ahci 0000:00:0e.0: controller can't do PMP, turning off CAP_PMP
[    0.855024] ahci 0000:00:0e.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[    0.855028] ahci 0000:00:0e.0: flags: 64bit ncq sntf led clo pio 
[    0.855035] ahci 0000:00:0e.0: setting latency timer to 64
[    0.855677] ------------[ cut here ]------------
[    0.855689] WARNING: at /build/buildd/linux-3.0.0/drivers/ata/libata-core.c:6087 ata_host_activate+0x109/0x110()
[    0.855692] Hardware name: ESPRIMO EDITION P2530         
[    0.855694] Modules linked in: ahci(+) libahci
[    0.855700] Pid: 166, comm: modprobe Not tainted 3.0.0-15-generic #26-Ubuntu
[    0.855702] Call Trace:
[    0.855709]  [<ffffffff8105e7ef>] warn_slowpath_common+0x7f/0xc0
[    0.855719]  [<ffffffffa0001f40>] ? ahci_port_intr+0x1d0/0x1d0 [libahci]
[    0.855722]  [<ffffffff8105e84a>] warn_slowpath_null+0x1a/0x20
[    0.855725]  [<ffffffff8141b109>] ata_host_activate+0x109/0x110
[    0.855730]  [<ffffffff814c3daa>] ? pcibios_set_master+0x7a/0xa0
[    0.855739]  [<ffffffffa000ccc8>] ahci_init_one+0x4e8/0x770 [ahci]
[    0.855746]  [<ffffffff811d8eb8>] ? sysfs_new_dirent+0x58/0x140
[    0.855752]  [<ffffffff8131036c>] local_pci_probe+0x5c/0xd0
[    0.855757]  [<ffffffff81311b79>] __pci_device_probe+0xf9/0x100
[    0.855762]  [<ffffffff812eac4a>] ? kobject_get+0x1a/0x30
[    0.855765]  [<ffffffff81311bba>] pci_device_probe+0x3a/0x60
[    0.855770]  [<ffffffff813cfcd8>] really_probe+0x68/0x190
[    0.855773]  [<ffffffff813cff65>] driver_probe_device+0x45/0x70
[    0.855776]  [<ffffffff813d003b>] __driver_attach+0xab/0xb0
[    0.855779]  [<ffffffff813cff90>] ? driver_probe_device+0x70/0x70
[    0.855782]  [<ffffffff813cff90>] ? driver_probe_device+0x70/0x70
[    0.855786]  [<ffffffff813cedcc>] bus_for_each_dev+0x5c/0x90
[    0.855789]  [<ffffffff813cfa9e>] driver_attach+0x1e/0x20
[    0.855792]  [<ffffffff813cf6f0>] bus_add_driver+0x1a0/0x270
[    0.855794]  [<ffffffffa0014000>] ? 0xffffffffa0013fff
[    0.855798]  [<ffffffff813d05a6>] driver_register+0x76/0x140
[    0.855801]  [<ffffffffa0014000>] ? 0xffffffffa0013fff
[    0.855804]  [<ffffffff81311856>] __pci_register_driver+0x56/0xd0
[    0.855812]  [<ffffffff8103b0f3>] ? set_memory_nx+0x43/0x50
[    0.855816]  [<ffffffffa001401e>] ahci_init+0x1e/0x1000 [ahci]
[    0.855823]  [<ffffffff81002042>] do_one_initcall+0x42/0x180
[    0.855829]  [<ffffffff8109fede>] sys_init_module+0xbe/0x230
[    0.855835]  [<ffffffff815fa1c2>] system_call_fastpath+0x16/0x1b
[    0.855837] ---[ end trace a1464e7698a8b855 ]---
[    0.856811] scsi0 : ahci
[    0.857258] scsi1 : ahci
[    0.860751] scsi2 : ahci
[    0.862691] wmi: Mapper loaded
[    0.864965] scsi3 : ahci
[    0.865151] ata1: SATA max UDMA/133 abar m8192@0xfe304000 port 0xfe304100
[    0.865155] ata2: SATA max UDMA/133 abar m8192@0xfe304000 port 0xfe304180
[    0.865158] ata3: SATA max UDMA/133 abar m8192@0xfe304000 port 0xfe304200
[    0.865161] ata4: SATA max UDMA/133 abar m8192@0xfe304000 port 0xfe304280
[    0.865258] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[    0.865444] ACPI: PCI Interrupt Link [LNKL] enabled at IRQ 21
[    0.865463] forcedeth 0000:00:0f.0: PCI INT A -> Link[LNKL] -> GSI 21 (level, high) -> IRQ 21
[    0.865470] forcedeth 0000:00:0f.0: setting latency timer to 64
[    0.871228] [drm] Initialized drm 1.1.0 20060810
[    0.899444] reset set in interrupt, calling generic_failure
[    0.899474] floppy0: no floppy controllers found
[    1.080053] usb 1-7: new high speed USB device number 4 using ehci_hcd
[    1.184042] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.184062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.188037] ata4: SATA link down (SStatus 0 SControl 300)
[    1.188064] ata3: SATA link down (SStatus 0 SControl 300)
[    1.218122] usbcore: registered new interface driver uas
[    1.389061] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:19:99:53:69:e7
[    1.389066] forcedeth 0000:00:0f.0: highdma pwrctl mgmt gbit lnktim msi desc-v3
[    1.516030] usb 2-4: new low speed USB device number 2 using ohci_hcd
[    2.044055] usb 2-6: new low speed USB device number 3 using ohci_hcd
[    2.296638] input: Microsoft Microsoft Wireless Optical Mouse® 1.0A as /devices/pci0000:00/0000:00:04.0/usb2/2-4/2-4:1.0/input/input2
[    2.296781] generic-usb 0003:045E:006A.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.0A] on usb-0000:00:04.0-4/input0
[    2.310355] input:   USB Keyboard as /devices/pci0000:00/0000:00:04.0/usb2/2-6/2-6:1.0/input/input3
[    2.310468] generic-usb 0003:04D9:1603.0002: input,hidraw1: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:04.0-6/input0
[    2.334160] input:   USB Keyboard as /devices/pci0000:00/0000:00:04.0/usb2/2-6/2-6:1.1/input/input4
[    2.334287] generic-usb 0003:04D9:1603.0003: input,hidraw2: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:04.0-6/input1
[    2.334310] usbcore: registered new interface driver usbhid
[    2.334312] usbhid: USB HID core driver
[    6.184045] ata1.00: qc timeout (cmd 0xec)
[    6.184054] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[    6.184073] ata2.00: qc timeout (cmd 0xa1)
[    6.184079] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[    6.504038] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    6.504055] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   16.504151] ata2.00: qc timeout (cmd 0xa1)
[   16.504158] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   16.504163] ata2: limiting SATA link speed to 1.5 Gbps
[   16.504175] ata1.00: qc timeout (cmd 0xec)
[   16.504180] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   16.504184] ata1: limiting SATA link speed to 1.5 Gbps
[   16.824040] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   21.864044] ata1: link is slow to respond, please be patient (ready=0)
[   26.512033] ata1: COMRESET failed (errno=-16)
[   26.832049] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   46.824064] ata2.00: qc timeout (cmd 0xa1)
[   46.824070] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   47.144043] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   56.832055] ata1.00: qc timeout (cmd 0xec)
[   56.832061] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   57.152042] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   57.153515] Initializing USB Mass Storage driver...
[   57.164093] scsi4 : usb-storage 1-7:1.0
[   57.164188] ACPI: PCI Interrupt Link [LNKQ] enabled at IRQ 20
[   57.164215] nouveau 0000:00:10.0: PCI INT A -> Link[LNKQ] -> GSI 20 (level, high) -> IRQ 20
[   57.164223] nouveau 0000:00:10.0: setting latency timer to 64
[   57.166679] [drm] nouveau 0000:00:10.0: Detected an NV40 generation card (0x063000a2)
[   57.170297] usbcore: registered new interface driver usb-storage
[   57.170300] USB Mass Storage support registered.
[   57.171093] [drm] nouveau 0000:00:10.0: Attempting to load BIOS image from PRAMIN
[   57.210792] [drm] nouveau 0000:00:10.0: ... appears to be valid
[   57.210796] [drm] nouveau 0000:00:10.0: BIT BIOS found
[   57.210799] [drm] nouveau 0000:00:10.0: Bios version 05.73.32.11
[   57.210803] [drm] nouveau 0000:00:10.0: TMDS table version 1.1
[   57.210804] [drm] nouveau 0000:00:10.0: TMDS table script pointers not stubbed
[   57.210807] [drm] nouveau 0000:00:10.0: BIT table 'd' not found
[   57.210809] [drm] nouveau 0000:00:10.0: Found Display Configuration Block version 3.0
[   57.210813] [drm] nouveau 0000:00:10.0: Raw DCB entry 0: 01000310 00000023
[   57.210815] [drm] nouveau 0000:00:10.0: Raw DCB entry 1: 01031322 00000080
[   57.210819] [drm] nouveau 0000:00:10.0: DCB connector table: VHER 0x30 5 10 2
[   57.210822] [drm] nouveau 0000:00:10.0:   0: 0x00000000: type 0x00 idx 0 tag 0xff
[   57.210825] [drm] nouveau 0000:00:10.0:   1: 0x00001161: type 0x61 idx 1 tag 0x07
[   57.210831] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 0 at offset 0xCE1D
[   57.210852] [drm] nouveau 0000:00:10.0: ======= misaligned reg 0x001020FB =======
[   57.210857] [drm] nouveau 0000:00:10.0: ======= misaligned reg 0x001020FB =======
[   57.210880] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 1 at offset 0xCF69
[   57.210883] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 2 at offset 0xCF6A
[   57.210905] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 3 at offset 0xD0EC
[   57.210910] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 4 at offset 0xD182
[   57.210913] [drm] nouveau 0000:00:10.0: Pointer to flat panel table invalid
[   57.210918] [drm] nouveau 0000:00:10.0: timingset 255 does not exist
[   57.230778] [drm] nouveau 0000:00:10.0: 1 available performance level(s)
[   57.230783] [drm] nouveau 0000:00:10.0: 0: memory 0MHz core 600MHz fanspeed 100%
[   57.230792] [drm] nouveau 0000:00:10.0: c: memory 0MHz core 348MHz
[   57.230912] [TTM] Zone  kernel: Available graphics memory: 1897902 kiB.
[   57.230914] [TTM] Initializing pool allocator.
[   57.230937] [drm] nouveau 0000:00:10.0: Detected 256MiB VRAM
[   57.231917] [drm] nouveau 0000:00:10.0: 64 MiB GART (aperture)
[   57.330574] [drm] nouveau 0000:00:10.0: Saving VGA fonts
[   57.366291] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   57.366293] [drm] No driver support for vblank timestamp query.
[   57.366654] [drm] nouveau 0000:00:10.0: Setting dpms mode 3 on vga encoder (output 0)
[   57.366658] [drm] nouveau 0000:00:10.0: Setting dpms mode 3 on tmds encoder (output 1)
[   57.496311] [drm] nouveau 0000:00:10.0: allocated 1024x768 fb: 0x49000, bo ffff8801147bcc00
[   57.496387] fbcon: nouveaufb (fb0) is primary device
[   57.509546] [drm] nouveau 0000:00:10.0: Setting dpms mode 0 on vga encoder (output 0)
[   57.509550] [drm] nouveau 0000:00:10.0: Output VGA-1 is running on CRTC 0 using output A
[   57.511505] Console: switching to colour frame buffer device 128x48
[   57.515444] fb0: nouveaufb frame buffer device
[   57.515446] drm: registered panic notifier
[   57.515455] [drm] Initialized nouveau 0.0.16 20090420 for 0000:00:10.0 on minor 0
[   58.169908] scsi 4:0:0:0: Direct-Access     Hitachi  HDT721010SLA360       PQ: 0 ANSI: 2 CCS
[   58.188588] sd 4:0:0:0: Attached scsi generic sg0 type 0
[   58.190395] sd 4:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[   58.193759] sd 4:0:0:0: [sda] Write Protect is off
[   58.193766] sd 4:0:0:0: [sda] Mode Sense: 00 38 00 00
[   58.195754] sd 4:0:0:0: [sda] Asking for cache data failed
[   58.195759] sd 4:0:0:0: [sda] Assuming drive cache: write through
[   58.200761] sd 4:0:0:0: [sda] Asking for cache data failed
[   58.200767] sd 4:0:0:0: [sda] Assuming drive cache: write through
[   70.182018]  sda: sda1 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
[   70.189762] sd 4:0:0:0: [sda] Asking for cache data failed
[   70.189766] sd 4:0:0:0: [sda] Assuming drive cache: write through
[   70.189770] sd 4:0:0:0: [sda] Attached SCSI disk
[   76.031323] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   95.042694] udevd[348]: starting version 173
[   95.087444] lp: driver loaded but no devices found
[   95.159281] Adding 1060252k swap on /dev/sda8.  Priority:-1 extents:1 across:1060252k 
[   95.223941] i2c i2c-2: nForce2 SMBus adapter at 0x3040
[   95.225820] i2c i2c-3: nForce2 SMBus adapter at 0x3000
[   95.260164] reset set in interrupt, calling generic_failure
[   95.260196] floppy0: no floppy controllers found
[   95.344845] Modular ISDN core version 1.1.21
[   95.344984] NET: Registered protocol family 34
[   95.352853] mISDNipac module version 2.0
[   95.355108] AVM Fritz PCI driver Rev. 2.1
[   95.355341] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[   95.355360] fcpci 0000:01:07.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, high) -> IRQ 11
[   95.355364] mISDN: found adapter Fritz!Card PCI v2 at 0000:01:07.0
[   95.355372] AVM.1: AVM Fritz!CARD PCIv2 config irq:11 base:0x4000
[   95.380051] AVM 1 cards installed DEBUG
[   95.485868] ACPI: PCI Interrupt Link [LNKM] enabled at IRQ 19
[   95.485896] HDA Intel 0000:00:09.0: PCI INT A -> Link[LNKM] -> GSI 19 (level, high) -> IRQ 19
[   95.485900] hda_intel: Disabling MSI
[   95.485956] HDA Intel 0000:00:09.0: setting latency timer to 64
[   95.514377] udevd[359]: renamed network interface eth0 to eth1
[   95.601872] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[   95.669998] HiSax: Linux Driver for passive ISDN cards
[   95.670003] HiSax: Version 3.5 (module)
[   95.670006] HiSax: Layer1 Revision 2.46.2.5
[   95.670008] HiSax: Layer2 Revision 2.30.2.4
[   95.670009] HiSax: TeiMgr Revision 2.20.2.3
[   95.670011] HiSax: Layer3 Revision 2.22.2.3
[   95.670013] HiSax: LinkLayer Revision 2.59.2.4
[   95.737623] hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0
[   95.758369] hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1
[   95.758380] Error: Driver 'fcpci' is already registered, aborting...
[   96.084060] hda_codec: ALC262: BIOS auto-probing.
[   96.376330] input: HDA NVidia Headphone as /devices/pci0000:00/0000:00:09.0/sound/card0/input5
[   97.117146] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[   97.248865] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[   97.639839] ppdev: user-space parallel port driver
[   98.262091] init: failsafe main process (704) killed by TERM signal
[  108.480042] eth1: no IPv6 routers present
[  108.631376] Bluetooth: Core ver 2.16
[  108.631413] NET: Registered protocol family 31
[  108.631415] Bluetooth: HCI device and connection manager initialized
[  108.631418] Bluetooth: HCI socket layer initialized
[  108.631420] Bluetooth: L2CAP socket layer initialized
[  108.633604] Bluetooth: SCO socket layer initialized
[  108.635909] Bluetooth: RFCOMM TTY layer initialized
[  108.635916] Bluetooth: RFCOMM socket layer initialized
[  108.635918] Bluetooth: RFCOMM ver 1.11
[  108.737506] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[  108.737511] Bluetooth: BNEP filters: protocol multicast
[  109.353664] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro,commit=0
[  109.440413] EXT4-fs (sda7): re-mounted. Opts: commit=0
[  109.523858] init: plymouth-stop pre-start process (1415) terminated with status 1
[  112.656054] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro,commit=0
[  112.687823] EXT4-fs (sda7): re-mounted. Opts: commit=0
Ist natürlich recht umfangreich.
Die Festplatte des Rechners, auf dem Windows und Debian installiert ist, wurde nicht erkannt.

Gruss H.
 
OP
H

halo44

Hacker
RME schrieb:
... Wenn bei Dir "Configure SATA as [AHCI]" dann mal [IDE] testen ...
Zum Vergrößern anklicken....

Hab ich jetzt gewagt : und es läuft, d.h. meine Suse-Installation habe ich soweit laufen lassen bis die Partitionen auf der Festplatte erkannt wurden und ein Partitionierungsvorschlag gemacht wurde.

Hier habe ich allerdings erstmal abgebrochen, neu gebootet und hierbei wieder auf AHCI umgestellt. Danach habe ich Windows getestet, welches auch läuft.

Damit ist also die Fehlerursache gefunden. Es ergibt sich jedoch die Frage, wie ich weiter vorgehen soll. Keinesfalls darf ich meiner Frau das Windowssystem beschädigen - das gibt Ärger :roll:

Wer hat einen Vorschlag?

Gruss H.
 
S

spoensche

Moderator
Teammitglied
Deine Platte wird im AHCI Modus nicht gefunden, weil der Kernel beim ATA Treiber Crashed. Die Platte wird erkannt, aber kann nicht angesprochen werden. (Siehe dmesg Ausgabe beim Ubuntu)

Du könntest mal testen, ob die Platte im AHCI Mode erkannt wird, wenn du den Bootparameter
Code: 
noapic
verwendest.
Ansonsten müsstest du mal testen, ob das Windows auch IDE Mode funktioniert.
 
OP
H

halo44

Hacker
spoensche schrieb:
... Du könntest mal testen, ob die Platte im AHCI Mode erkannt wird, wenn du den Bootparameter
Code: 
noapic
verwendest.
Ansonsten müsstest du mal testen, ob das Windows auch IDE Mode funktioniert.
Zum Vergrößern anklicken....

Den Test mit noapic habe ich schon erfolglos versucht.

Ich werde mal prüfen, was Windows zum IDE Mode sagt und dann berichten.

Gruss H.
 
RME

RME

Advanced Hacker
Von den geposteten Links:
Bei Microsoft Windows Vista, Windows 7 sowie Windows 8 Consumer Preview muss, falls das System im IDE-Modus installiert wurde, dazu erst ein Schlüssel in der Windows Registry geändert werden,[1] da sonst ein Blue Screen auftritt...
Zum Vergrößern anklicken....
Some operating systems, notably Windows Vista and Windows 7, do not configure themselves to load the AHCI driver upon boot if the SATA-drive controller was not in AHCI mode at the time of installation. This can cause failure to boot with an error message if the SATA controller is later switched to AHCI mode...
Zum Vergrößern anklicken....
Probleme gibts wenn Windows mit BIOS SATA = IDE installiert wurde und dann (nach der Installation) auf AHCI umkonfiguriert wird.

Vom Umgekehrten Fall (der bei Dir zutrifft) ist nicht die Rede. und sollte keine Probleme geben.
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben