Diese Website existiert nur weil wir Werbung mit AdSense ausliefern.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.

[gelöst]Bios/Mainboard-Problem oder evtl. kaputt?

Alles rund um die Systemverwaltung, die Administration und Konfiguration Eures Linuxsystems

Moderator: Moderatoren

Antworten
bilimbi
Newbie
Newbie
Beiträge: 39
Registriert: 10. Feb 2007, 23:10

[gelöst]Bios/Mainboard-Problem oder evtl. kaputt?

Beitrag von bilimbi » 29. Apr 2009, 15:52

Hallo zusammen,

mir ist da was komisches passiert: während ich eine DVD kopiert habe mit Suse 11.0 und nebenbei ein bischen im Internet gesurft und e-mails abgerufen habe, fror der Bildschirm plötzlich ein. Es hat gar nichts mehr funktioniert. Irgendwann schob dann die CD-Lade auf und mir wurde die fertige Kopie gemeldet. Anders ging aber gar nüschts.

Normalerweise kann ich beim Start auswählen, ob ich Suse oder WindowsXP nutzen möchte. Jetzt aber wurde beim Neustart gemeldet "booting from local disc. Isolinux: Disk Error 01, AX=0201, drive 80. Boot failed: press any key to retry." Als ich das machte, startete er relativ normal, nur hielt er nach der ersten Zeile schon an mit "AutoDetecting PriMaster press F4 to abort" und als ich F4 drückte, kam "AutoDetecting PriSlave press F4 to abort" - Der Rest lief normal durch. Nur gestartet ist er nicht. Ich habe dann die Suse-Installations-CD eingeschoben und Repair installed system gewählt. Daraufhin sagte er mir, no hard disks were found. Check your hardware. Außerdem kam noch eine Meldung (rot hinterlegt) an error occurred during the installation. Ich konnte auch Windows nicht starten. Nach dem dritten Versuch fuhr Windows hoch und aktuell ist Linux gestartet, dem ich die untenstehenden Infos entlockt habe.

Ich vermute irgendeinen Konflikt zwischen Bios und Mainboard - das ist es aber auch schon. Mit meinen Vermutungen kann ich wenig anfangen, da ich nicht gerade DER Computer-Crack bin... :/ Hoffentlich hat die Festplatte keinen mitgekriegt. Hat jemand von Euch vielleicht noch einen Tip? Und sorry, wenn das da unten zuviel Input auf einmal sein sollte, bitte Bescheid geben, dann lösche ich, was unnötig ist (das müsste mir aber dann auch jemand genau sagen, was unnötig ist :ops: )

Viele Grüße, bilimbi

CPU-Informationen
Prozessor (CPU): AMD Athlon(tm) XP 2200+
Geschwindigkeit: 1 798,30 MHz
Speicherinformationen
Gesamtspeicher (RAM): 1,5 GB
Freier Speicher: 1 020,9 MB (+ 295,7 MB Zwischenspeicher)
Freier Swap: 2,0 GB
Betriebssystem
Betriebssystem: Linux 2.6.25.20-0.1-pae i686
Aktueller Benutzer: eltern@linux-1ill
System: openSUSE 11.0 (i586)
KDE: 3.5.9 "release 49.1"

Linux version 2.6.25.20-0.1-pae (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-12-12 20:30:38 +0100
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
BIOS-e820: 000000005fff0000 - 000000005fff8000 (ACPI data)
BIOS-e820: 000000005fff8000 - 0000000060000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
639MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Entering add_active_range(0, 0, 393200) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 393200
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 393200
On node 0 totalpages: 393200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 1279 pages used for memmap
HighMem zone: 162545 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000FA8B0, 0014 (r0 AMI )
ACPI: RSDT 5FFF0000, 002C (r1 AMIINT VIA_K7 10 MSFT 97)
ACPI: FACP 5FFF0030, 0081 (r1 AMIINT VIA_K7 11 MSFT 97)
ACPI: DSDT 5FFF0120, 3502 (r1 VIA K7VT4 1000 INTL 2002024)
ACPI: FACS 5FFF8000, 0040
ACPI: APIC 5FFF00C0, 0054 (r1 AMIINT VIA_K7 9 MSFT 97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390129
Kernel command line: root=/dev/disk/by-id/scsi-SATA_WDC_WD800BB-00CWD-WMA8E3057663-part6 resume=/dev/sda5 splash=silent vga=0x31a
bootsplash: silent mode.
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1798.301 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1548524k/1572800k available (1955k kernel code, 23004k reserved, 1682k data, 264k init, 655296k highmem)
virtual kernel memory layout:
fixmap : 0xff8b2000 - 0xfffff000 (7476 kB)
pkmap : 0xff400000 - 0xff600000 (2048 kB)
vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0495000 - 0xc04d7000 ( 264 kB)
.data : 0xc02e8e2a - 0xc048d784 (1682 kB)
.text : 0xc0100000 - 0xc02e8e2a (1955 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay using timer specific routine.. 3601.26 BogoMIPS (lpj=7202526)
Security Framework initialized
AppArmor: AppArmor initialized <NULL>
AppArmor: Registered secondary security module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 18k freed
ACPI: Core revision 20070126
ACPI: Checking initramfs for custom DSDT
Parsing all Control Methods:
Table [DSDT](id 0001) - 513 Objects with 47 Devices 149 Methods 32 Regions
tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
CPU0: AMD Athlon(tm) XP 2200+ stepping 00
Total of 1 processors activated (3601.26 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000001
groups: 00000000,00000000,00000000,00000001
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfda71, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 0 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package initialization:.........................................................................................
Initialized 27/32 Regions 9/9 Fields 44/44 Buffers 9/23 Packages (522 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 0 _STA executions (examined 50 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
AppArmor: AppArmor Filesystem Enabled
ACPI: RTC can wake from S4
system 00:05: ioport range 0x295-0x296 has been reserved
system 00:05: ioport range 0x3f0-0x3f1 has been reserved
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:05: ioport range 0x400-0x40f has been reserved
system 00:05: ioport range 0x800-0x87f has been reserved
system 00:05: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:05: iomem range 0xfee00000-0xfee00fff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: 0xdde00000-0xdfefffff
PREFETCH window: 0x00000000cdc00000-0x00000000ddcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 5357k freed
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
type=2000 audit(1241016337.652:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 10240k, total 65536k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:ea70
vesafb: pmi: set display start = c00ceab5, set palette = c00ceb3a
vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 208945 bytes
bootsplash: ...found (1280x1024, 220863 bytes, v3).
Console: switching to colour frame buffer device 156x60
Switched to high resolution mode on CPU 0
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
NET: Registered protocol family 1
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
Write protecting the kernel read-only data: 1440k
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
ACPI: ACPI0007:00 is registered as cooling_device0
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
pata_via 0000:00:0f.1: version 0.3.3
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
ata1.00: ATA-5: WDC WD800BB-00CAA1, 17.07W17, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: TOSHIBA DVD-ROM SD-M1612, 1004, max UDMA/33
ata2.01: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL10, max UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA WDC WD800BB-00CA 17.0 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-M1612 1004 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-4167B DL10 PQ: 0 ANSI: 5
sata_via 0000:00:0f.0: version 2.3
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 10
scsi2 : sata_via
scsi3 : sata_via
ata3: SATA max UDMA/133 cmd 0xec00 ctl 0xe800 bmdma 0xdc00 irq 20
ata4: SATA max UDMA/133 cmd 0xe400 ctl 0xe000 bmdma 0xdc08 irq 20
ata3: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ata4: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<6>usbcore: registered new interface driver usbfs
sda1 sda2 <<6>usbcore: registered new interface driver hub
sda5<6>usbcore: registered new device driver usb
sda6<6>USB Universal Host Controller Interface driver v3.0
sda7 >
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
sd 0:0:0:0: [sda] Attached SCSI disk
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000c800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25.20-0.1-pae uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:10.4: irq 21, io mem 0xdfffae00
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25.20-0.1-pae ehci_hcd
usb usb2: SerialNumber: 0000:00:10.4
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000cc00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25.20-0.1-pae uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25.20-0.1-pae uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
hub 2-0:1.0: unable to enumerate USB device on port 2
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.25.20-0.1-pae uhci_hcd
usb usb5: SerialNumber: 0000:00:10.3
PM: Starting manual resume from disk
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: New USB device found, idVendor=057c, idProduct=2000
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB ISDN-Connector
usb 1-1: Manufacturer: AVM Berlin
usb 1-2: new low speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: New USB device found, idVendor=045e, idProduct=0047
usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=0
usb 1-2: Product: Microsoft 5-Button Mouse with IntelliEye(TM)
usb 1-2: Manufacturer: Microsoft
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2:1.0/input/input2
input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:10.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
Linux agpgart interface v0.103
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
ACPI: Sleep Button (CM) [SLPB]
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
parport_pc 00:03: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
gameport: NS558 PnP Gameport is pnp00:04/gameport0, io 0x200, speed 1011kHz
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23
eth0: VIA Rhine II at 0x1c000, 00:13:8f:2b:a3:46, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
CAPI Subsystem Rev 1.1.2.8
ppdev: user-space parallel port driver
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[dfffb000-dfffb7ff] Max Packet=[2048] IR/IT contexts=[8/8]
capifs: Rev 1.1.2.3
capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
ALSA sound/pci/via82xx.c:1925: Using DXS as PCM Playback
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000199000002885b]
capidrv: Rev 1.1.2.2: loaded
Adding 2104504k swap on /dev/sda5. Priority:-1 extents:1 across:2104504k
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
type=1505 audit(1241009176.756:2): operation="profile_load" name="/bin/ping" name2="default" pid=1431
type=1505 audit(1241009176.884:3): operation="profile_load" name="/sbin/klogd" name2="default" pid=1487
type=1505 audit(1241009176.956:4): operation="profile_load" name="/sbin/syslog-ng" name2="default" pid=1494
type=1505 audit(1241009177.020:5): operation="profile_load" name="/sbin/syslogd" name2="default" pid=1502
type=1505 audit(1241009177.100:6): operation="profile_load" name="/usr/sbin/avahi-daemon" name2="default" pid=1505
type=1505 audit(1241009177.164:7): operation="profile_load" name="/usr/sbin/identd" name2="default" pid=1512
type=1505 audit(1241009177.228:8): operation="profile_load" name="/usr/sbin/mdnsd" name2="default" pid=1516
type=1505 audit(1241009177.300:9): operation="profile_load" name="/usr/sbin/nscd" name2="default" pid=1521
type=1505 audit(1241009177.388:10): operation="profile_load" name="/usr/sbin/ntpd" name2="default" pid=1527
type=1505 audit(1241009177.452:11): operation="profile_load" name="/usr/sbin/traceroute" name2="default" pid=1533
powernow-k8: Processor cpuid 680 not supported
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 17
eth0: no IPv6 routers present
NET: Registered protocol family 4
NET: Registered protocol family 3
NET: Registered protocol family 5

Dateisystem Größe Benut Verf Ben% Eingehängt auf
/dev/sda6 14G 5,2G 7,9G 40% /
udev 760M 120K 760M 1% /dev
/dev/sda7 21G 3,7G 16G 20% /home
/dev/sda1 34G 15G 19G 44% /windows/C
Zuletzt geändert von bilimbi am 29. Apr 2009, 17:19, insgesamt 1-mal geändert.

Werbung:
Benutzeravatar
lOtz1009
Moderator
Moderator
Beiträge: 7147
Registriert: 23. Jan 2008, 09:51
Wohnort: Sulzbach/Ts.

Re: Bios/Mainboard-Problem oder evtl. kaputt?

Beitrag von lOtz1009 » 29. Apr 2009, 16:09

Im Log hab ich mal auf die Schnelle nix relevantes gefunden. Hast du nach dem "Hänger" einen Kaltstart gemacht? Ansonsten kann es sein, dass sich eins der Laufwerke kurzzeitig aufgehängt hat und den Bus überladen hat. Dann kann das BIOS beim Starten nicht auf die Laufwerke zugreifen.
Ist mir mal passiert als mein letzter Brenner den Geist aufgegeben hat. Der hörte einfach nicht mehr auf :D
Nach STRG+ALT+ENTF (allerdings unter Windows) hatte ich selbiges Problem beim POST. Nach einem Kaltstart gings wieder.
::: openSUSE Member :::
::: LXDE-Team :::
Linux-Club Wiki
vi is an editor with two modes: one which destroys your input and the other which beeps at you.
Für meine Beiträge gilt:
Bild

bilimbi
Newbie
Newbie
Beiträge: 39
Registriert: 10. Feb 2007, 23:10

Re: Bios/Mainboard-Problem oder evtl. kaputt?

Beitrag von bilimbi » 29. Apr 2009, 16:21

Hi IOtz,

ja genau, mit Kaltstart da raus und dann normal neu gestartet, was dann erst mal nicht funktionierte. Du meinst also, kaputt ist eher nichts?

Mich treibt zusätzlich noch folgende Frage um: bei Windows drückt man ja die berühmten drei Tasten STRG+ALT+ENTF, um abgestürzte Programme zu beenden und (hoffentlich) trotzdem mit dem Rest weiterarbeiten zu können. Hat Suse sowas eigentlich auch oder kommt man bei Suse nur mit einem Kaltstart raus, wenn sonst nix mehr geht?

Viele Grüße, bilimbi

Benutzeravatar
lOtz1009
Moderator
Moderator
Beiträge: 7147
Registriert: 23. Jan 2008, 09:51
Wohnort: Sulzbach/Ts.

Re: Bios/Mainboard-Problem oder evtl. kaputt?

Beitrag von lOtz1009 » 29. Apr 2009, 16:34

Naja wenn du nen kompletten Kaltstart gemacht hast ist mein "Szenario" eher unwahrscheinlich, denn dabei werden die Laufwerke idR kurzzeitig abgeschaltet.

Unter KDE gibts (oder gab? habs schon ewig nicht mehr gebraucht) mit STRG+ESC eine Art Taskmanager. Ansonsten kannste das auch fein über Konsole mittels ps oder top und anschließendem kill.
Man kann auch den kompletten X-Server mit STRG+ALT+Backspace neustarten. Bzw. muss man das mittlerweile zwei mal machen. Beim ersten Mal gibts nur einen Warnton (was auch Sinn macht).
::: openSUSE Member :::
::: LXDE-Team :::
Linux-Club Wiki
vi is an editor with two modes: one which destroys your input and the other which beeps at you.
Für meine Beiträge gilt:
Bild

bilimbi
Newbie
Newbie
Beiträge: 39
Registriert: 10. Feb 2007, 23:10

Re: Bios/Mainboard-Problem oder evtl. kaputt?

Beitrag von bilimbi » 29. Apr 2009, 17:19

Hi,

danke schön, das hab' ich mir gleich mal notiert. Ich markiere das Thema erst mal als gelöst, sollte der Fehler wieder auftreten, kann ich es ja wieder aufwärmen ;)

Viele Grüße, bilimbi

Antworten

Wer ist online?

Mitglieder in diesem Forum: Baidu [Spider], Bing [Bot] und 1 Gast