OpenSuse 11 Fehler beim Lesen von Sektor 2

OpenSuse 11 Installation bricht ab mit
Fehler beim Lesen von Sektor 2
Diese DVD ist fehlerhaft.

OpenSuse 11 lässt sich nicht auf meinem Heim PC installieren
auf dem bereits OpenSuse 10.2 installiert ist
und hervorragend läuft. Auf meinem notebook hingegen habe ich keinerlei
Fehlermeldungen.

Ich versuche Euch zu beschreiben was meine Diagnose ergeben hat.

Vielleicht kann mir jemand helfen da ich gerne von 10.2 -> 11 Updaten würde.
Es erübrigt sich zu sagen dass ich dies alles sehr seltsam finde.
Da OpenSuse 10.2 auf dem Rechner super läuft. Wieso also diese Schwierigkeiten
bei der Installation von OpenSuse 11 ?

Unter OpenSuse 10.2 habe ich folgende Dateien geprüft
# md5sum openSUSE-11.0-DVD-i386.iso
ed6a5b3feb668866df812b1c2aed9d7f openSUSE-11.0-DVD-i386.iso

# md5sum openSUSE-11.0-KDE4-LiveCD-i386.iso
83b1a04f18d6782cfe0407edadac377f openSUSE-11.0-KDE4-LiveCD-i386.iso

Der MEDIACHECK von ergab openSUSE-11.0-KDE4-LiveCD-i386.iso
nach Booten des OpenSuse 11 System folgendes :

app: GENISOIMAGE ISO 9660/HFS FILESYSTEM CREATOR (C) 1993 E.YOUNGDALE (C) 1997-2006 J
media: CD1
size: 659678 kB
pad: 0 kB
check: 99%
err: sector 329837
check: md5sum wrong
md5: f2e3f602a68197659cab6d001b16beae

Auf meinem Notebook hingegen habe ich ebenfalls den Mediacheck von openSUSE-11.0-KDE4-LiveCD-i386.iso
durchgeführt die Berechnung ergab folgendes :

app: GENISOIMAGE ISO 9660/HFS FILESYSTEM CREATOR (C) 1993 E.YOUNGDALE (C) 1997-2006 J
media: CD1
size: 659678 kB
pad: 0 kB
check: 100%
check: md5Sum OK
md5: 83b1a04f18d6782cfe0407edadac377f

Auf meinem Heim PC ergab sich beim booten von openSUSE-11.0-DVD-i386.iso
und der option Prüfe Installationsmedium

folgende Fehlermeldung

Fehler beim Lesen von Sektor 2
Diese DVD ist fehlerhaft.

Ich habe auf meinem notebook und auf einem weiteren Rechner diese Fehlermeldung nicht erhalten.
Hier läuft die Prüfung durch bis zur Installationsauswahl.

Kann ich nun davon ausgehen das die openSUSE-11.0-DVD-i386.iso nicht fehlerhaft ist ?
Ich habe schon einige DVD Rohlinge gebrannt, immer das gleiche Heim PC Fehler andere PC OK...

Entweder die Hardware meines Heim PC ist nicht kompatibel mit openSUSE-11.0-DVD-i386.iso
und openSUSE-11.0-KDE4-LiveCD-i386.iso oder ich habe etwas übersehen ?

Das meine Laufwerke oder mein PC defekt ist möchte ich erstmal ausschließen, schließlich
läuft hier die Opensuse 10.2 super.

Für jeden sachdienlichen Hinweis bin ich Dankbar.

Bin mal gespannt wie wir gemeinsam dieses Problem in den Griff bekommen.

Für Eure Hilfe möchte ich mich schon jetzt bedanken.

http://wiki.linux-club.de/opensuse/Open_SuSE_auf_DVD_brennen#Wenn_es_dennoch_Fehler_gibt
Laufwerk auf dem geschrieben wird in Kombination mit Fehlerquelle 1 2 3 5 oder 6 ?

robi

Hallo Robi,

vielen Dank für die schnelle Antwort, leider kann ich bis jetzt noch keinen
Erfolg vermelden.
Zu Deinem Tip nun folgendes ...

Wenn es dennoch Fehler gibt

Gibt es trotz korrekter md5sum und trotz (scheinbar) korrektem Brennen noch immer Fehler (z.B.: Suse installiert nicht, wirft Fehler aus, etc.) dann kann dies u.a. folgende Gründe haben:

1. Häufig treten Fehler auf, wenn ISO-Images auf RW-Medien gebrannt werden. Es wird daher dringend davon abgeraten, ISO-Images auf CD-RW oder DVD-RW Medien zu brennen!

Zu 1. Ich benutze hier DVD-R und DVD+R Medien die bis jetzt noch keine Fehler meldeten.


2. Vielleicht wurde die CD/DVD zu schnell gebrannt. Zu schnelles Brennen kann Schreibfehler verursachen. => Der Brennvorgang sollte mit deutlich langsamerer Geschwindigkeit wiederholt werden. (Kein Scherz!)

Zu 2. Ich habe mit Nero unter WinXP SP3 gebrannt die langsamste Schreibgeschwindigkeit gewählt
bei 2.4x(3.324 KB/S)

3. Billige Rohlinge verwendet? Auch billige Rohlinge können zu Fehlern neigen und hinterher die seltsamsten Probleme bereiten.
Zu 3. Die DVD+R und DVD-R sind von Tevion. Habe ich wohl beim ALDI gekauft. Was würdet Ihr empfehlen ?

4. CD/DVD verkratzt oder verdreckt? Kratzer oder Dreck auf einer CD/DVD können zu Lesefehlern führen.
Zu. 4 Sehen blitz blank und sauber aus.

5. Laufwerk ausgenudelt oder verdreckt? Auch ein ausgelutschtes oder verdrecktes Laufwerk kann zu Lesefehlern und Installationsproblemen führen. => Falls möglich, sollte in diesem Fall ein anderes Laufwerk getestet und verwendet werden.

Zu.5 Ich habe es noch nicht geöffnet. Ich denke nicht das es ausgenudelt und verdreckt ist.
Es wird nachfolgend so unter OpenSuse 10.2 erkannt

7: udi = '/org/freedesktop/Hal/devices/storage_model_SONY_DVD_ROM_DDU1615'
block.minor = 0 (0x0)
storage.requires_eject = true
info.capabilities = { 'storage', 'block', 'storage.cdrom' }
storage.bus = 'ide'
storage.cdrom.support_media_changed = true
storage.removable.media_available = false
storage.cdrom.hddvdr = false
org.freedesktop.Hal.Device.resmgr.method_names = { 'Grant', 'Revoke' }
info.category = 'storage'
info.product = 'SONY DVD-ROM DDU1615'
storage.drive_type = 'cdrom'
storage.hotpluggable = false
storage.physical_device = '/org/freedesktop/Hal/devices/pci_1106_571_ide_1_0'
storage.vendor = ''
storage.media_check_enabled = true
storage.cdrom.read_speed = 7056 (0x1b90)
org.freedesktop.Hal.Device.Storage.method_names = { 'Eject', 'CloseTray' }
storage.cdrom.dvd = true
block.is_volume = false
storage.firmware_version = 'GYS1'
storage.cdrom.bdre = false
block.storage_device = '/org/freedesktop/Hal/devices/storage_model_SONY_DVD_ROM_DDU1615'
info.addons = { 'hald-addon-storage' }
info.parent = '/org/freedesktop/Hal/devices/pci_1106_571_ide_1_0'
storage.cdrom.dvdplusr = false
org.freedesktop.Hal.Device.resmgr.method_signatures = { '', '' }
storage.size = 0ull (0x0ull)
storage.cdrom.write_speed = 0 (0x0)
org.freedesktop.Hal.Device.Storage.method_signatures = { 'as', 'as' }
block.device = '/dev/hdc'
info.callouts.add = { 'hal-resmgr' }
org.freedesktop.Hal.Device.Storage.method_argnames = { 'extra_options', 'extra_options' }
storage.cdrom.cdr = false
storage.no_partitions_hint = true
storage.cdrom.bdr = false
storage.removable = true
storage.cdrom.dvdram = false
storage.cdrom.dvdplusrwdl = false
storage.cdrom.write_speeds = { }
storage.cdrom.dvdr = false
info.interfaces = { 'org.freedesktop.Hal.Device.Storage', 'org.freedesktop.Hal.Device.Storage', 'org.freedesktop.Hal.Device.resmgr' }
org.freedesktop.Hal.Device.Storage.method_execpaths = { 'hal-storage-eject', 'hal-storage-closetray' }
storage.model = 'SONY DVD-ROM DDU1615'
info.udi = '/org/freedesktop/Hal/devices/storage_model_SONY_DVD_ROM_DDU1615'
info.callouts.remove = { 'hal-resmgr' }
storage.cdrom.dvdplusrdl = false
storage.cdrom.bd = false
storage.cdrom.hddvdrw = false
block.major = 22 (0x16)
resmgr.class = 'cdrom'
linux.hotplug_type = 3 (0x3)
storage.cdrom.dvdplusrw = false
storage.cdrom.cdrw = false
org.freedesktop.Hal.Device.resmgr.method_argnames = { '', '' }
linux.sysfs_path = '/sys/block/hdc'
storage.cdrom.dvdrw = false
storage.automount_enabled_hint = true
linux.sysfs_path_device = '/sys/block/hdc'
storage.cdrom.hddvd = false
org.freedesktop.Hal.Device.resmgr.method_execpaths = { 'hal-resmgr-grant', 'hal-resmgr-revoke' }

Ich hoffe das war jetzt nicht zuviel Hardware Informationen.
Wichtiger Hinweis !!! Wenn ich bei der Installation von OpenSuse 11 auf die Option Installation
gehe, meldet Yast ich solle die CDROM 1 einlegen. Wird etwa mein DVD Laufwerk als
CDROM Laufwerk bei der Installation von OpenSuse 11 erkannt ? Wie kann man das ändern ?

6. Das Laufwerk benötigt eventuell eine neue Firmware. Unter http://www.cdrinfo.com/Sections/Firmware/Home.aspx gibt es die neuste Firmware für fast alle CD/DVD Laufwerke zum Herunterladen. Zum Updaten der Firmware ist allerdings Windows erforderlich, da es sich meist um .exe Files handelt.

Ja würde ich machen, wenn es absolut erforderlich ist und ich eine Quelle finde und empfohlen bekomme.

Also so schnell gibt das orchkatzl nicht auf ! ;-)

Vielleicht fällt hier im Forum von dem ich schon viel über Linux erfahren habe noch etwas sachdienliches ein.

Nochmal meine Frage. Kann es sein das mein DVD Laufwerk bei eingelegter Installations DVD
Opensuse 11 als CD Laufwerk erkannt wird ? Warum ist das so ? Wie kann ich das ändern ?

Übrigens DVDISASTER ergab keine Fehler. Obwohl ich mir nicht sicher bin ob ich das
absolut richtig bediene.

Gruss Orchkatzl

Eben habe ich mein System nochmal gebootet und die
Installations Option ausgewählt. Es kommt die Meldung.
*************************************************
Opensuse

Linuxrc v.3.1.34 (kernel 2.6.25.5-1.1-default)

Stellen Sie sicher, dass sich die CD1 in Ihrem Laufwerk befindet.

OK Zurück
*************************************************

Aber ich habe doch die OpenSuse 11 DVD eingelegt ?
Gruss Orchkatzl

Hi

Irgendwie schnalle ich das nicht.
Mit Suse 10.2 kannst du booten ebenso mit der Suse 11 DVD auf anderen Rechnern?
Irgendwie unlogisch. :?
Keine Ahnung was bei dir schief geht.

cu

Bei mir weigerte sich auch ein Laufwerk, die 11.0 zu booten. Im anderen Laufwerk ging es (md5sum und Mediencheck OK).
=> Ausgenudeltes/verdrecktes Laufwerk am Ende seiner Zeit. => Shit happens.
Da wird wohl bei mir demnächst ein neues Laufwerk oder aufgrund des Rechneralters gleich ein neuer Rechner fällig.

Ich tippe bei dir auf einen der Fehler aus der Liste im Wiki. Vermutlich auch das Laufwerk.

Hallo Whois,
Deine Worte gelassen ausgesprochen,
Irgendwie Unlogisch :?

Da gebe ich Dir recht. Früher haben wir mehr Worte gebraucht
Was nicht sein kann, darf auch nicht sein !

Deshalb wende ich mich ja an Euch, sowas so seltsames hatte ich noch nie.
Ich habe einige DVD gebrannt nur mit diesem Rechner läuft es einfach nicht.

Wäre es denn logisch das bei der OpenSuse 11 Installation eine Einstellung weggefallen ist die auf meinen PC eine Installation nicht möglich macht ?

Wie kann man das überprüfen ?

Zu Griffin das würde ja bedeuten, kauf Dir neue Hardware um OpenSuse 11 zu installieren. Dann versuch ich es lieber
nochmal mit der Netzwerkinstallation ! :idea:

Gruss Orchkatzl

Ich würde an deiner Stelle 10.2 starten, von der DVD ein Image erstellen und dann die md5sum Prüfsumme generieren. Geht z.B. einfach mit K3b, Menü Extras -> DVD kopieren -> Nur Abbild-Datei erzeugen. Ist die Prüfsumme ok liegt das Problem bei 11.0, sollte sie aber Fehlerhaft seien würde ich auf Hardwarefehler tippen.

orchkatzl schrieb:

Zu Griffin das würde ja bedeuten, kauf Dir neue Hardware um OpenSuse 11 zu installieren. Dann versuch ich es lieber nochmal mit der Netzwerkinstallation ! :idea:

Zum Vergrößern anklicken....

Ich würde es eher so formulieren: "Kauf dir neue Hardware, weil die alte langsam seltsam und unzuverlässig wird."
Fehler bei der Suse Installation sind immerhin nur ein Symptom des Problems, nicht dessen Ursache.

Mein Laufwerk funktioniert in vielen Bereichen durchaus noch ganz gut. In anderen bereichen treten aber langsam Fehler auf. Klar könnte ich diese Fehler jetzt ignorieren, bis der endgültige Exitus eintritt. (Das mache ich ja auch bereits seit einiger Zeit; immerhin habe ich ja zwei Laufwerke im Rechner.) Wenn ich das Problem jedoch an der Wurzel packen und lösen möchte, wird irgendwann mal ein neues Laufwerk fällig.
Wann man das macht, ob man mit den Problemen leben kann und ob man alternativen hat, muss dann jeder selber für sich beurteilen.

Ob dein Laufwerk wirklich ausgenudelt oder verdreckt ist, kann ich nicht sagen. Es ist nur eine sich mir aufdrängende Vermutung, wenn du alle anderen Fehlerquellen aus dem oben genannten Wiki Artikel ausgeschlossen hast.

Hallo !
Vielen Dank für Eure Antworten. An meiner Hardware hat wirklich etwas nicht gestimmt. Anscheinend
ist das Verbindungskabel vom Motherboard zum DVD Laufwerk defekt gewesen. Nehme ich jedenfalls an.
OpenSuse 11 ist bereits installiert. Merkwürdig ist das OpenSuse 10.2 der Kabeldefekt nicht gestört hat.

Das Booten von OpenSuse 11 dauert mir noch etwas zu lange.
Aber wenn das System dann endlich hochgefahren ist, dann läuft alles Super.

Wie ist der Boot Prozeß zu optimieren ? Die Ausgaben verstehe ich nur teilweise.
Nochmal vielen Dank für den Tip meine Hardware zu überprüfen.
Das folgende ist das OpenSuse 11 Startprotokoll mit deren Hilfe ich gerne die Startzeit meines Linux
System optimieren möchte.
Die Stellen die etwas länger dauern habe ich Rot markiert.
Deuten diese Fehler etwa auch auf Hardwarefehler meines PC hin ?

Wie gehe ich da am besten vor ?
Für sachdienliche Hinweise ...

Vielen Dank und Gruss Orchkatzl

Inspecting /boot/System.map-2.6.25.9-0.2-pae
Loaded 28179 symbols from /boot/System.map-2.6.25.9-0.2-pae.
Symbols match kernel version 2.6.25.
No module symbols loaded - kernel modules not enabled.

klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.25.9-0.2-pae (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-06-28 00:00:07 +0200
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
<4> BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
<4> BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<5>0MB HIGHMEM available.
<5>511MB LOWMEM available.
<6>Scan SMP from c0000000 for 1024 bytes.
<6>Scan SMP from c009fc00 for 1024 bytes.
<6>Scan SMP from c00f0000 for 65536 bytes.
<6>Scan SMP from c009fc00 for 1024 bytes.
<7>Entering add_active_range(0, 0, 131056) 0 entries of 256 used
<4>Zone PFN ranges:
<4> DMA 0 -> 4096
<4> Normal 4096 -> 131056
<4> HighMem 131056 -> 131056
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4> 0: 0 -> 131056
<7>On node 0 totalpages: 131056
<7> DMA zone: 32 pages used for memmap
<7> DMA zone: 0 pages reserved
<7> DMA zone: 4064 pages, LIFO batch:0
<7> Normal zone: 991 pages used for memmap
<7> Normal zone: 125969 pages, LIFO batch:31
<7> HighMem zone: 0 pages used for memmap
<7> Movable zone: 0 pages used for memmap
<6>DMI not present or invalid.
<6>Using APIC driver default
<4>ACPI: RSDP 000F7A30, 0014 (r0 AWARD )
<4>ACPI: RSDT 1FFF3000, 0028 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<4>ACPI: FACP 1FFF3040, 0074 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<4>ACPI: DSDT 1FFF30C0, 25CB (r1 AWARD AWRDACPI 1000 MSFT 100000C)
<4>ACPI: FACS 1FFF0000, 0040
<3>ACPI: no DMI BIOS year, acpi=force is required to enable ACPI
<4>ACPI: Disabling ACPI support
<4>Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
<6>PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
<6>PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
<6>PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130033
<5>Kernel command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 resume=/dev/sda1 splash=silent vga=0x317
<6>bootsplash: silent mode.
<6>Local APIC disabled by BIOS -- you can enable it with "lapic"
<7>mapped APIC to ffffb000 (0140c000)
<6>Enabling fast FPU save and restore... done.
<6>Initializing CPU#0
<4>PID hash table entries: 2048 (order: 11, 8192 bytes)
<4>Detected 697.670 MHz processor.
<4>Console: colour dummy device 80x25
<6>console [tty0] enabled
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 509424k/524224k available (1953k kernel code, 14276k reserved, 1676k data, 264k init, 0k highmem)
<6>virtual kernel memory layout:
<4> fixmap : 0xff8b2000 - 0xfffff000 (7476 kB)
<4> pkmap : 0xff400000 - 0xff600000 (2048 kB)
<4> vmalloc : 0xe0800000 - 0xff3fe000 ( 491 MB)
<4> lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
<4> .init : 0xc0493000 - 0xc04d5000 ( 264 kB)
<4> .data : 0xc02e858a - 0xc048b784 (1676 kB)
<4> .text : 0xc0100000 - 0xc02e858a (1953 kB)
<6>Checking if this processor honours the WP bit even in supervisor mode...Ok.
<7>CPA: page pool initialized 1 of 1 pages preallocated
<4>Calibrating delay using timer specific routine.. 1397.46 BogoMIPS (lpj=2794926)
<6>Security Framework initialized
<6>AppArmor: AppArmor initialized <NULL>
<6>AppArmor: Registered secondary security module capability
<6>Capability LSM initialized as secondary
<4>Mount-cache hash table entries: 512
<6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
<6>CPU: L2 Cache: 64K (64 bytes/line)
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<4>Compat vDSO mapped to ffffe000.
<6>Checking 'hlt' instruction... OK.
<6>SMP alternatives: switching to UP code
<6>Freeing SMP alternatives: 18k freed
<4>CPU0: AMD Duron(tm) processor stepping 00
<5>SMP motherboard not detected.
<5>Local APIC not detected. Using dummy APIC emulation.
<6>Brought up 1 CPUs
<7>CPU0 attaching sched-domain:
<7> domain 0: span 00000000,00000000,00000000,00000001
<7> groups: 00000000,00000000,00000000,00000001
<6>net_namespace: 548 bytes
<6>Booting paravirtualized kernel on bare hardware
<6>NET: Registered protocol family 16
<6>PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1
<6>PCI: Using configuration type 1
<6>Setting up standard PCI resources
<6>ACPI: Interpreter disabled.
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI: disabled
<6>PnPBIOS: Scanning system for PnP BIOS support...
<6>PnPBIOS: Found PnP BIOS installation structure at 0xc00fbe10
<6>PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbe40, dseg 0xf0000
<6>PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
<4>PCI: Probing PCI hardware
<7>PCI: Probing PCI hardware (bus 00)
<6>pci 0000:00:07.4: quirk: region 4000-40ff claimed by vt82c586 ACPI
<6>pci 0000:00:07.4: quirk: region 6000-607f claimed by vt82c686 HW-mon
<6>pci 0000:00:07.4: quirk: region 5000-500f claimed by vt82c686 SMB
<6>PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
<6>AppArmor: AppArmor Filesystem Enabled
<4>ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread DF41E020 could not acquire Mutex [3] [20070126]
<6>system 00:07: iomem range 0x0-0x9ffff could not be reserved
<6>system 00:07: iomem range 0xfffe0000-0xffffffff could not be reserved
<6>system 00:07: iomem range 0xfee00000-0xfee0ffff has been reserved
<6>system 00:07: iomem range 0x100000-0x1fffffff could not be reserved
<6>system 00:08: iomem range 0xf0000-0xf3fff could not be reserved
<6>system 00:08: iomem range 0xf4000-0xf7fff could not be reserved
<6>system 00:08: iomem range 0xf8000-0xfbfff could not be reserved
<6>system 00:08: iomem range 0xfc000-0xfffff could not be reserved
<6>system 00:0b: ioport range 0x208-0x20f has been reserved
<6>PCI: Bridge: 0000:00:01.0
<6> IO window: 9000-9fff
<6> MEM window: 0xd4000000-0xd5ffffff
<6> PREFETCH window: 0x00000000d0000000-0x00000000d3ffffff
<7>PCI: Setting latency timer of device 0000:00:01.0 to 64
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>TCP reno registered
<6>Unpacking initramfs... done
<6>Freeing initrd memory: 5238k freed
<6>Machine check exception polling timer started.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(1215858350.724:1): initialized
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>PCI: VIA PCI bridge detected. Disabling DAC.
<6>pci 0000:00:07.0: Disabling VIA external APIC routing
<7>pci 0000:01:00.0: Boot video device
<6>vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 6144k, total 32768k
<6>vesafb: mode is 1024x768x16, linelength=2048, pages=20
<6>vesafb: protected mode interface info at c000:441b
<6>vesafb: pmi: set display start = c00c4489, set palette = c00c44c3
<6>vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
<6>vesafb: scrolling: redraw
<6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<6>bootsplash 3.1.6-2004/03/31: looking for picture...
<6>bootsplash: silentjpeg size 166113 bytes
<6>bootsplash: ...found (1024x768, 154167 bytes, v3).
<4>Console: switching to colour frame buffer device 124x44
<6>fb0: VESA VGA frame buffer device
<6>isapnp: Scanning for PnP cards...
<6>pnp: SB audio device quirk - increasing port range
<6>pnp: AWE32 quirk - adding two ports
<6>isapnp: Card 'Creative SB32 PnP'
<6>isapnp: 1 Plug & Play card detected total
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>serio: i8042 AUX port at 0x60,0x64 irq 12
<6>mice: PS/2 mouse device common for all mice
<6>input: PC Speaker as /devices/platform/pcspkr/input/input0
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<4>registered taskstats version 1
<6>Freeing unused kernel memory: 264k freed
<6>Write protecting the kernel read-only data: 1432k
<6>input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
<4>Clocksource tsc unstable (delta = 63978296 ns)
<4>ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread DF9730A0 could not acquire Mutex [1] [20070126]
<6>No dock devices found.
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<7>pata_via 0000:00:07.1: version 0.3.3
<7>PCI: Setting latency timer of device 0000:00:07.1 to 64
<6>scsi0 : pata_via
<6>scsi1 : pata_via
<6>ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xa000 irq 14
<6>ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xa008 irq 15
<6>input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input2
<6>ata1.00: ATAPI: SONY DVD-ROM DDU1615, GYS1, max UDMA/66
<6>ata1.01: ATAPI: HL-DT-ST GCE-8400B, 1.02, max MWDMA2
<6>ata1.00: configured for UDMA/66
<6>ata1.01: configured for MWDMA2
<6>ata2.00: ATA-4: SAMSUNG SV2044D, MM100-45, max UDMA/66
<6>ata2.00: 39862368 sectors, multi 16: LBA
<6>ata2.00: configured for UDMA/66
<5>scsi 0:0:0:0: CD-ROM SONY DVD-ROM DDU1615 GYS1 PQ: 0 ANSI: 5
<5>scsi 0:0:1:0: CD-ROM HL-DT-ST CD-RW GCE-8400B 1.02 PQ: 0 ANSI: 5
<5>scsi 1:0:0:0: Direct-Access ATA SAMSUNG SV2044D MM10 PQ: 0 ANSI: 5
<4>thermal: Unknown symbol acpi_processor_set_thermal_limit
<6>BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
<4>Driver 'sd' needs updating - please use bus_type methods
<5>sd 1:0:0:0: [sda] 39862368 512-byte hardware sectors (20410 MB)
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>sd 1:0:0:0: [sda] 39862368 512-byte hardware sectors (20410 MB)
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6> sda: sda1 sda2 sda3
<5>sd 1:0:0:0: [sda] Attached SCSI disk
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>USB Universal Host Controller Interface driver v3.0
<7>PCI: setting IRQ 3 as level-triggered
<6>PCI: Found IRQ 3 for device 0000:00:09.0
<7>PCI: Setting latency timer of device 0000:00:09.0 to 64
<6>uhci_hcd 0000:00:09.0: UHCI Host Controller
<6>uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
<6>uhci_hcd 0000:00:09.0: irq 3, io base 0x0000bc00
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: UHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.25.9-0.2-pae uhci_hcd
<6>usb usb1: SerialNumber: 0000
<7>PCI: setting IRQ 11 as level-triggered
<6>PCI: Found IRQ 11 for device 0000:00:09.1
<6>PCI: Sharing IRQ 11 with 0000:00:0a.0
<7>PCI: Setting latency timer of device 0000:00:09.1 to 64
<6>uhci_hcd 0000:00:09.1: UHCI Host Controller
<6>uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 2
<6>uhci_hcd 0000:00:09.1: irq 11, io base 0x0000c000
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
<6>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: UHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.25.9-0.2-pae uhci_hcd
<6>usb usb2: SerialNumber: 0000
<7>PCI: setting IRQ 5 as level-triggered
<6>PCI: Found IRQ 5 for device 0000:00:09.2
<6>PCI: Sharing IRQ 5 with 0000:00:0b.0
<7>PCI: Setting latency timer of device 0000:00:09.2 to 64
<6>ehci_hcd 0000:00:09.2: EHCI Host Controller
<6>ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 3
<6>ehci_hcd 0000:00:09.2: irq 5, io mem 0xd7410000
<6>ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 4 ports detected
<6>usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: EHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.25.9-0.2-pae ehci_hcd
<6>usb usb3: SerialNumber: 0000
<6>usb 3-3: new high speed USB device using ehci_hcd and address 2
<6>usb 3-3: configuration #1 chosen from 1 choice
<6>usb 3-3: New USB device found, idVendor=059f, idProduct=1010
<6>usb 3-3: New USB device strings: Mfr=2, Product=3, SerialNumber=1
<6>usb 3-3: Product: LaCie Desktop Hard Drive
<6>usb 3-3: Manufacturer: LaCie
<6>usb 3-3: SerialNumber: SAMSUNG H
<6>PM: Starting manual resume from disk
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda2, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<5>scsi 0:0:0:0: Attached scsi generic sg0 type 5
<5>scsi 0:0:1:0: Attached scsi generic sg1 type 5
<5>sd 1:0:0:0: Attached scsi generic sg2 type 0
<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>Initializing USB Mass Storage driver...
<6>natsemi dp8381x driver, version 2.1, Sept 11, 2006
<6> originally by Donald Becker <becker@scyld.com>
<6> 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
<6>PCI: Found IRQ 11 for device 0000:00:0a.0
<6>PCI: Sharing IRQ 11 with 0000:00:09.1
<7>PCI: Setting latency timer of device 0000:00:0a.0 to 64
<6>natsemi eth0: NatSemi DP8381[56] at ########## (###########), ##############, IRQ 11, port TP.
<6>scsi2 : SCSI emulation for USB Mass Storage devices
<6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<7>usb-storage: device found at 2
<7>usb-storage: waiting for device to settle before scanning
<6>Linux agpgart interface v0.103
<6>agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
<6>agpgart: AGP aperture is 4M @ 0xd7000000
<6>8139too Fast Ethernet driver 0.9.28
<6>PCI: Found IRQ 5 for device 0000:00:0b.0
<6>PCI: Sharing IRQ 5 with 0000:00:09.2
<7>PCI: Setting latency timer of device 0000:00:0b.0 to 64
<6>eth1: RealTek RTL8139 at ##############, ##############, IRQ 5
<7>eth1: Identified 8139 chip type 'RTL-8100B/8139D'
<7>parport_pc: VIA 686A/8231 detected
<7>parport_pc: probing current configuration
<7>parport_pc: Current parallel port base: 0x0
<6>parport_pc: VIA parallel port disabled in BIOS
<5>scsi 2:0:0:0: Direct-Access SAMSUNG HD500LJ PQ: 0 ANSI: 2
<5>sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
<5>sd 2:0:0:0: [sdb] Write Protect is off
<7>sd 2:0:0:0: [sdb] Mode Sense: 38 00 00 00
<3>sd 2:0:0:0: [sdb] Assuming drive cache: write through
<4>Driver 'sr' needs updating - please use bus_type methods
<5>sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
<5>sd 2:0:0:0: [sdb] Write Protect is off
<7>sd 2:0:0:0: [sdb] Mode Sense: 38 00 00 00
<3>sd 2:0:0:0: [sdb] Assuming drive cache: write through
<6> sdb:sr0: scsi3-mmc drive: 78x/125x cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.20
<4> sdb1
<5>sd 2:0:0:0: [sdb] Attached SCSI disk
<5>sd 2:0:0:0: Attached scsi generic sg3 type 0
<7>usb-storage: device scan complete
<7>sr 0:0:0:0: Attached scsi CD-ROM sr0
<4>sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
<7>sr 0:0:1:0: Attached scsi CD-ROM sr1
<6>b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
<3>ata2.00: BMDMA stat 0x24
<3>ata2.00: cmd ca/00:00:61:f3:17/00:00:00:00:00/e0 tag 0 dma 131072 out
<4> res 51/84:00:60:f4:17/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
<3>ata2.00: status: { DRDY ERR }
<3>ata2.00: error: { ICRC ABRT }
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/66
<6>ata2: EH complete
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
<3>ata2.00: BMDMA stat 0x24
<3>ata2.00: cmd ca/00:00:61:f3:17/00:00:00:00:00/e0 tag 0 dma 131072 out
<4> res 51/84:01:60:f4:17/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
<3>ata2.00: status: { DRDY ERR }
<3>ata2.00: error: { ICRC ABRT }
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/66
<6>ata2: EH complete
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
<3>ata2.00: BMDMA stat 0x24
<3>ata2.00: cmd ca/00:00:61:f3:17/00:00:00:00:00/e0 tag 0 dma 131072 out
<4> res 51/84:01:60:f4:17/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
<3>ata2.00: status: { DRDY ERR }
<3>ata2.00: error: { ICRC ABRT }
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/66
<6>ata2: EH complete
<4>ata2.00: limiting speed to UDMA/44IO4
<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
<3>ata2.00: BMDMA stat 0x24
<3>ata2.00: cmd ca/00:00:61:f3:17/00:00:00:00:00/e0 tag 0 dma 131072 out
<4> res 51/84:01:60:f4:17/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
<3>ata2.00: status: { DRDY ERR }
<3>ata2.00: error: { ICRC ABRT }
<6>ata2: soft resetting link
<6>ata2.00: configured for UDMA/44
<6>ata2: EH complete
<5>sd 1:0:0:0: [sda] 39862368 512-byte hardware sectors (20410 MB)
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
<6>ns558 01:01.01: activated
<6>gameport: NS558 PnP Gameport is pnp01:01.01/gameport0, io 0x200, speed 523kHz
<5>sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
<5>sd 1:0:0:0: [sda] 39862368 512-byte hardware sectors (20410 MB)
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>flexcop-pci: will use the HW PID filter.
<6>flexcop-pci: card revision 2
<7>PCI: setting IRQ 7 as level-triggered
<6>PCI: Found IRQ 7 for device 0000:00:0c.0
<7>PCI: Setting latency timer of device 0000:00:0c.0 to 64
<6>pata_isapnp 01:01.03: activated
<6>DVB: registering new adapter (FlexCop Digital TV device)
<6>b2c2-flexcop: MAC address = 00:#################
<6>rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
<6>rtc0: alarms up to one year, y3k
<6>scsi3 : pata_isapnp
<6>ata3: PATA max PIO0 cmd 0x168 ctl 0x36e irq 10
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci(+) rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10892fc>] ata_bmdma_drive_eh+0x91/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci(+) rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e1081869>] ata_std_postreset+0x4f/0x80 [libata]
<4> [<e108a28e>] ata_eh_reset+0x5e0/0x6f2 [libata]
<4> [<e108bb68>] ata_eh_recover+0x3c8/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci(+) rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e1081879>] ata_std_postreset+0x5f/0x80 [libata]
<4> [<e108a28e>] ata_eh_reset+0x5e0/0x6f2 [libata]
<4> [<e108bb68>] ata_eh_recover+0x3c8/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci(+) rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e107fb08>] ata_dev_select+0x63/0xb4 [libata]
<4> [<e1082b3e>] ata_dev_read_id+0x61/0x39a [libata]
<4> [<e108bd85>] ata_eh_recover+0x5e5/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci(+) rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e107fb08>] ata_dev_select+0x63/0xb4 [libata]
<4> [<e107fcc5>] ata_qc_issue_prot+0x52/0x1cb [libata]
<4> [<e1080a2b>] ata_qc_issue+0x2b7/0x2e6 [libata]
<4> [<e1082609>] ata_exec_internal_sg+0x269/0x40b [libata]
<4> [<e1082809>] ata_exec_internal+0x5e/0x66 [libata]
<4> [<e1082bc3>] ata_dev_read_id+0xe6/0x39a [libata]
<4> [<e108bd85>] ata_eh_recover+0x5e5/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci(+) rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e1089572>] ata_exec_command+0x1b/0x28 [libata]
<4> [<e107fd6c>] ata_qc_issue_prot+0xf9/0x1cb [libata]
<4> [<e1080a2b>] ata_qc_issue+0x2b7/0x2e6 [libata]
<4> [<e1082609>] ata_exec_internal_sg+0x269/0x40b [libata]
<4> [<e1082809>] ata_exec_internal+0x5e/0x66 [libata]
<4> [<e1082bc3>] ata_dev_read_id+0xe6/0x39a [libata]
<4> [<e108bd85>] ata_eh_recover+0x5e5/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<6>ppdev: user-space parallel port driver
<6>b2c2-flexcop: found the stv0299 at i2c address: 0x68
<4>DVB: registering frontend 0 (ST STV0299 DVB-S)...
<6>b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
<4>ata3.01: qc timeout (cmd 0xec)
<4>ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
<4>ata3: failed to recover some devices, retrying in 5 secs
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: stv0299 ppdev rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e1081869>] ata_std_postreset+0x4f/0x80 [libata]
<4> [<e108a28e>] ata_eh_reset+0x5e0/0x6f2 [libata]
<4> [<e108bb68>] ata_eh_recover+0x3c8/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: stv0299 ppdev rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e1081879>] ata_std_postreset+0x5f/0x80 [libata]
<4> [<e108a28e>] ata_eh_reset+0x5e0/0x6f2 [libata]
<4> [<e108bb68>] ata_eh_recover+0x3c8/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: stv0299 ppdev rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e107fb08>] ata_dev_select+0x63/0xb4 [libata]
<4> [<e1082b3e>] ata_dev_read_id+0x61/0x39a [libata]
<4> [<e108bd85>] ata_eh_recover+0x5e5/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<3>Bad IO access at port 0x0 (return inb(port))
<4>------------[ cut here ]------------
<4>WARNING: at lib/iomap.c:44 bad_io_access+0x2f/0x34()
<4>Modules linked in: stv0299 ppdev rtc_cmos(+) pata_isapnp(+) b2c2_flexcop_pci rtc_core 8139cp ns558 b2c2_flexcop gameport rtc_lib sr_mod dvb_core parport_pc 8139too firmware_class i2c_viapro cdrom via_agp mii parport agpgart i2c_core shpchp natsemi usb_storage via686a pci_hotplug sg ehci_hcd uhci_hcd usbcore sd_mod edd ext3 mbcache jbd pata_via libata scsi_mod dock
<4>Pid: 903, comm: scsi_eh_3 Tainted: G N 2.6.25.9-0.2-pae #1
<4> [dump_trace+99/551] dump_trace+0x63/0x227
<4> [show_trace+21/41] show_trace+0x15/0x29
<4> [dump_stack+91/101] _etext+0x5b/0x65
<4> [warn_on_slowpath+65/103] warn_on_slowpath+0x41/0x67
<4> [bad_io_access+47/52] bad_io_access+0x2f/0x34
<4> [ioread8+40/47] ioread8+0x28/0x2f
<4> [<e1089246>] ata_altstatus+0x1d/0x1f [libata]
<4> [<e10818bd>] ata_std_dev_select+0x23/0x30 [libata]
<4> [<e107fb08>] ata_dev_select+0x63/0xb4 [libata]
<4> [<e107fcc5>] ata_qc_issue_prot+0x52/0x1cb [libata]
<4> [<e1080a2b>] ata_qc_issue+0x2b7/0x2e6 [libata]
<4> [<e1082609>] ata_exec_internal_sg+0x269/0x40b [libata]
<4> [<e1082809>] ata_exec_internal+0x5e/0x66 [libata]
<4> [<e1082bc3>] ata_dev_read_id+0xe6/0x39a [libata]
<4> [<e108bd85>] ata_eh_recover+0x5e5/0x972 [libata]
<4> [<e108c288>] ata_do_eh+0x31/0x7f [libata]
<4> [<e1089335>] ata_bmdma_drive_eh+0xca/0xd4 [libata]
<4> [<e108937d>] ata_bmdma_error_handler+0x3e/0x47 [libata]
<4> [<e108c9e2>] ata_scsi_error+0x2b8/0x507 [libata]
<4> [<e1056af3>] scsi_error_handler+0xab/0x434 [scsi_mod]
<4> [kthread+59/97] kthread+0x3b/0x61
<4> [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
<4> =======================
<4>---[ end trace 80e9e1c932d32e9f ]---
<4>ata3.01: qc timeout (cmd 0xec)
<4>ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
<4>ata3: failed to recover some devices, retrying in 5 secs
<4>ata3.01: qc timeout (cmd 0xec)
<4>ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
<4>ata3: failed to recover some devices, retrying in 5 secs
<4>ata3.00: qc timeout (cmd 0xec)
<4>ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
<4>ata3: failed to recover some devices, retrying in 5 secs
<4>ata3.00: qc timeout (cmd 0xec)
<4>ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
<4>ata3: failed to recover some devices, retrying in 5 secs
<4>ata3.00: qc timeout (cmd 0xec)
<4>ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
<4>ata3: failed to recover some devices, retrying in 5 secs
<6>sbawe 01:01.00: activated
<6>sbawe 01:01.02: activated
<6>Adding 779112k swap on /dev/sda1. Priority:-1 extents:1 across:779112k
<6>device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
<6>loop: module loaded
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on sda3, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<5>type=1505 audit(1215858589.295:2): operation="profile_load" name="/bin/ping" name2="default" pid=1211
<5>type=1505 audit(1215858589.475:3): operation="profile_load" name="/sbin/klogd" name2="default" pid=1231
<4>fuse init (API version 7.9)
<5>type=1505 audit(1215858589.823:4): operation="profile_load" name="/sbin/syslog-ng" name2="default" pid=1246
<5>type=1505 audit(1215858590.171:5): operation="profile_load" name="/sbin/syslogd" name2="default" pid=1262
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Sat Jul 12 10:25:51 2008

FATAL: Error inserting processor (/lib/modules/2.6.25.9-0.2-pae/kernel/drivers/acpi/processor.ko): No such device
WARNING: Error inserting processor (/lib/modules/2.6.25.9-0.2-pae/kernel/drivers/acpi/processor.ko): No such device
FATAL: Error inserting thermal (/lib/modules/2.6.25.9-0.2-pae/kernel/drivers/acpi/thermal.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error inserting fan (/lib/modules/2.6.25.9-0.2-pae/kernel/drivers/acpi/fan.ko): No such device
Creating device nodes with udev
Trying manual resume from /dev/sda1
Invoking userspace resume from /dev/sda1
resume: libgcrypt version: 1.4.0
Trying manual resume from /dev/sda1
Invoking in-kernel resume from /dev/sda1
Waiting for device /dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 to appear: ok
fsck 1.40.8 (13-Mar-2008)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2
/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2: clean, 98108/905760 files, 727998/3620649 blocks
fsck succeeded. Mounting root device read-write.
Mounting root /dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2

Boot logging started on /dev/tty1(/dev/console (deleted)) at Sat Jul 12 12:25:58 2008

done
Starting udevd: done
Loading required kernel modules
doneActivating swap-devices in /etc/fstab...
donemount: according to mtab, /dev/sda2 is already mounted on /

Setting up the hardware clockdone
Activating device mapper...
done
Checking file systems...
fsck 1.40.8 (13-Mar-2008)
/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part3: clean, 222/292032 files, 53651/1166720 blocks
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda3 on /home type ext3 (rw,acl,user_xattr)
doneMounting securityfs on /sys/kernel/security done
Loading AppArmor profiles Loading fuse module done
Mounting fuse control filesystemdone
<notice>killproc: kill(477,29)
Creating /var/log/boot.msg
donedone
Activating remaining swap-devices in /etc/fstab...
doneSetting up hostname 'linux-9ak3'done
Setting up loopback interface lo
lo IP address: 127.0.0.1/8
IP address: 127.0.0.2/8
done
Retry device configuration: done
Configuring serial ports...
Configured serial ports
doneSetting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
fs.inotify.max_user_watches = 65536
net.ipv4.conf.default.promote_secondaries = 1
net.ipv4.conf.all.promote_secondaries = 1
done
Enabling syn flood protectiondone
Disabling IP forwardingdone
done
System Boot Control: The system has been set up
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(477,3)

INIT:
Boot logging started on /dev/tty1(/dev/console) at Sat Jul 12 12:29:54 2008

Master Resource Control: previous runlevel: N, switching to runlevel: 5
Entering runlevel: 5


<notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
Starting resource managerdone
Starting D-Bus daemonacpid: no ACPI support in kernelskipped
<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng -a /var/lib/named/dev/log ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PWD=/ PREVLEVEL=N LINES=44 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PWD=/ PREVLEVEL=N LINES=44 SHLVL=2 HOME=/ SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/sbin/klogd ]
Starting syslog servicesdone
done
Starting ConsoleKit<notice>startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ]
done
Loading CPUFreq modulesChecking/updating CPU microcode unused
Initializing random number generatordone
Starting Firewall Initialization (phase 1 of 2) done
(CPUFreq not supported)
Starting HAL daemondone
Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8
IP address: 127.0.0.2/8
done eth0 device: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
No configuration found for eth0
unused eth1 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
<notice>startproc: execve (/usr/bin/kdm) [ /usr/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PWD=/ LANG=de_DE.UTF-8 PREVLEVEL=N LINES=44 QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ XCURSOR_THEME=DMZ WINDOWMANAGER=/usr/bin/startkde4 SPLASH=yes splash=silent ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/bin/kdm ]
eth1 (DHCP) . . . <notice>pidofproc: dhcpcd 2170
. <notice>killproc: kill(1530,20)
IP/Netmask: '192.168.178.20'<notice>killproc: kill(1527,1)
<notice>killproc: kill(1530,18)
/ '255.255.255.0'<notice>killproc: kill(1530,12)

doneSetting up service network . . . . . . . . . . . . . . . .done
Starting service kdmdone
Starting RPC portmap daemon<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/sbin/portmap ]
done
Mount CIFS File Systems unused
Loading keymap i386/qwertz/de-latin1-nodeadkeys.map.gz
doneLoading compose table latin1.adddone
Start Unicode mode
doneLoading console font lat9w-16.psfu -m trivial G0:loadable
<notice>checkproc: /usr/bin/kdm 2193
done<notice>checkproc: /usr/bin/kdm 2193
<notice>killproc: kill(2179,15)
Starting auditd <notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/sbin/auditd ]
done
Starting Avahi daemon<notice>startproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ]
.<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ]
Starting cupsddone
Starting java.binfmt_misc done
done
Starting Avahi DNS Configuration daemon<notice>startproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ]
done
Starting Name Service Cache Daemon<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
done
Starting mail service (Postfix)<notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ]
Starting powersaved: done
done
Starting CRON daemon<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
done
Starting SSH daemon<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/openSUSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV-part2 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
done
Starting Firewall Initialization (phase 2 of 2) done
done
Master Resource Control: runlevel 5 has been reached
Skipped services in runlevel 5: acpid microcode.ctl smbfs
<notice>killproc: kill(1481,3)

Da stimmt immer noch irgendwas mit den Laufwerken nicht.
Teste die mal mit einem der Testtools der Hersteller.
Findet man z. B. auf der www.ultimatebootcd.com