• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst]Ethernet Controller auf Asus Board kein Treiber?

J

jgoe1

Member
Hallo Forum,
in meinem Neuen Rechner befindet sich ein Onboard Netzwerkanschluss (Asus P5Q). Leider bekomme ich den nicht konfiguriert, Meldung: wahrscheinlich kein Treiber. Ich habe schon in Google nachgesehen und etliche Beiträge gefunden, leider verstehe ich davon nicht alles. Bisher habe ich mir mit einer Netzwerkkarte geholfen, die belegt aber unnötig einen PCI-Steckplatz.

Kann mir da jemand helfen?

Danke und Gruß

Josef :???:
 
OP
J

jgoe1

Member
Hallo spoensche,
Dank für Deine Antwort. Spoensch hört sich fast so an, als ob Du aus dem Rheinland kommst.

Hier die Ausgabe von "lscpi -v" bezogen auf Attasic:

Code: 
02:00.0 Ethernet controller: Attansic Technology Corp. Device 1026 (rev b0)
        Subsystem: ASUSTeK Computer Inc. Device 8226
        Flags: bus master, fast devsel, latency 0, IRQ 11
        Memory at fe9c0000 (64-bit, non-prefetchable) [size=256K]
        I/O ports at cc00 [size=128]
        Capabilities: [40] Power Management version 2
        Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
        Capabilities: [58] Express Endpoint, MSI 00

und die Ausgabe von "hwinfo --netcard" ebenfalls bezogen auf Attasic.

Code: 
11: PCI 200.0: 0200 Ethernet controller
  [Created at pci.310]
  UDI: /org/freedesktop/Hal/devices/pci_1969_1026
  Unique ID: B35A.1owu3FJlCU9
  Parent ID: HnsE.cl8tOgOWATC
  SysFS ID: /devices/pci0000:00/0000:00:1c.5/0000:02:00.0
  SysFS BusID: 0000:02:00.0
  Hardware Class: network
  Model: "Attansic Ethernet controller"
  Vendor: pci 0x1969 "Attansic Technology Corp."
  Device: pci 0x1026
  SubVendor: pci 0x1043 "ASUSTeK Computer Inc."
  SubDevice: pci 0x8226
  Revision: 0xb0
  Memory Range: 0xfe9c0000-0xfe9fffff (rw,non-prefetchable)
  I/O Ports: 0xcc00-0xcc7f (rw)
  IRQ: 11 (no events)
  Module Alias: "pci:v00001969d00001026sv00001043sd00008226bc02sc00i00"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #23 (PCI bridge)
Gruß Josef
 
S

spoensche

Moderator
Teammitglied
Erkannt wird die Karte. Bekommst du die Fehlermeldung (Womöglich kein Treiber), wenn du versuchts die Karte mit Yast zu konfigurieren?


Poste mal die Ausgabe von
Code: 
lsmod
( als root ausführen)

Das nächste mal bitte code Tags verwenden, um die Ausgaben zu kennzeichnen, dann ist es leesbarer.
 
OP
J

jgoe1

Member
Hallo spoensche,
ich hoffe, dass ich das mit den Code Tags richtig mache. Ja ich bekomme die Meldung: Wahrscheinlich kein Treiber.
Hier die Ausgabe von lsmod:

Code: 
josgoe@linux-hjs1:~> lsmod
Module                  Size  Used by
joydev                 15936  0
ip6t_LOG               11140  8
xt_tcpudp               7296  6
xt_pkttype              6016  3
ipt_LOG                10500  9
xt_limit                6788  17
af_packet              26368  0
ip6t_REJECT             9088  3
nf_conntrack_ipv6      21240  4
ipt_REJECT              8064  3
xt_state                6656  8
iptable_mangle          7424  0
iptable_nat            11400  0
nf_nat                 23448  1 iptable_nat
iptable_filter          7552  1
ip6table_mangle         7296  0
nf_conntrack_netbios_ns     6912  0
nf_conntrack_ipv4      15364  7 iptable_nat,nf_nat
nf_conntrack           66900  6 nf_conntrack_ipv6,xt_state,iptable_nat,nf_nat,nf_conntrack_netbios_ns,nf_conntrack_ipv4
ip_tables              17936  3 iptable_mangle,iptable_nat,iptable_filter
ip6table_filter         7424  1
ip6_tables             19088  3 ip6t_LOG,ip6table_mangle,ip6table_filter
x_tables               21380  11 ip6t_LOG,xt_tcpudp,xt_pkttype,ipt_LOG,xt_limit,ip6t_REJECT,ipt_REJECT,xt_state,iptable_nat,ip_tables,ip6_tables
ipv6                  269160  19 ip6t_REJECT,nf_conntrack_ipv6,ip6table_mangle
snd_pcm_oss            52096  0
snd_mixer_oss          21120  1 snd_pcm_oss
binfmt_misc            15752  1
microcode              15888  0
snd_seq                61376  0
snd_seq_device         12812  1 snd_seq
cpufreq_conservative    12168  0
cpufreq_userspace       8452  0
cpufreq_powersave       5888  0
acpi_cpufreq           13324  1
speedstep_lib           9220  0
fuse                   54044  1
loop                   23044  0
dm_mod                 66388  0
lnbp21                  6400  1
stv0299                14728  1
dvb_ttpci             105160  0
dvb_core               84072  2 stv0299,dvb_ttpci
firmware_class         13696  2 microcode,dvb_ttpci
snd_hda_intel         374300  1
saa7146_vv             52224  1 dvb_ttpci
saa7146                23304  2 dvb_ttpci,saa7146_vv
videobuf_dma_sg        18436  1 saa7146_vv
videobuf_core          23172  2 saa7146_vv,videobuf_dma_sg
videodev               35712  1 saa7146_vv
rtc_cmos               14752  0
snd_pcm                87812  2 snd_pcm_oss,snd_hda_intel
snd_timer              28424  2 snd_seq,snd_pcm
snd_page_alloc         14984  2 snd_hda_intel,snd_pcm
snd_hwdep              14084  1 snd_hda_intel
v4l1_compat            17284  2 saa7146_vv,videodev
ohci1394               35760  0
usblp                  18560  0
8139too                30592  0
rtc_core               24860  1 rtc_cmos
snd                    67256  10 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_pcm,snd_timer,snd_hwdep
ttpci_eeprom            6400  1 dvb_ttpci
usb_storage            88584  0
mii                     9600  1 8139too
ieee1394               94728  1 ohci1394
soundcore              11976  1 snd
i2c_i801               13840  0
sr_mod                 21032  1
button                 13072  0
rtc_lib                 7040  1 rtc_core
sg                     39732  0
nvidia               6900656  26
agpgart                38580  1 nvidia
i2c_core               28820  6 lnbp21,stv0299,dvb_ttpci,ttpci_eeprom,i2c_i801,nvidia
cdrom                  38300  1 sr_mod
uhci_hcd               28432  0
sd_mod                 32920  8
ehci_hcd               39436  0
usbcore               152268  5 usblp,usb_storage,uhci_hcd,ehci_hcd
edd                    14152  0
ext3                  143624  5
mbcache                13060  1 ext3
jbd                    61216  1 ext3
fan                    10372  0
ata_piix               26116  7
pata_marvell           10880  0
libata                164188  2 ata_piix,pata_marvell
scsi_mod              156020  5 usb_storage,sr_mod,sg,sd_mod,libata
dock                   15248  1 libata
thermal                28060  0
processor              53804  2 acpi_cpufreq,thermal
josgoe@linux-hjs1:~>


Gruß Josef
 
S

spoensche

Moderator
Teammitglied
Und das mit dem "Wahrscheinlich kein Treiber" ist die original Fehlermeldung von Yast? Das wäre mal ne ganz neue Fehlermeldung.

Poste mal die Ausgabe von
Code: 
ifconfig -a
und
Code: 
uname -r
und
Code: 
lspci -vv
 
OP
J

jgoe1

Member
Hallo spoenche,
hier die Gewünschten Daten:

Code: 
linux-hjs1:/home/josgoe # ifconfig -a
eth0      Link encap:Ethernet  Hardware Adresse 00:0D:88:3C:3A:6D
          inet Adresse:192.168.1.76  Bcast:192.168.1.255  Maske:255.255.255.0
          inet6 Adresse: fe80::20d:88ff:fe3c:3a6d/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:223715 errors:0 dropped:0 overruns:0 frame:0
          TX packets:134642 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000
          RX bytes:299538876 (285.6 Mb)  TX bytes:15201838 (14.4 Mb)
          Interrupt:17 Basisadresse:0xa800

lo        Link encap:Lokale Schleife
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:268 errors:0 dropped:0 overruns:0 frame:0
          TX packets:268 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0
          RX bytes:23190 (22.6 Kb)  TX bytes:23190 (22.6 K

Code: 
linux-hjs1:/home/josgoe # uname -r
2.6.25.16-0.1-default

Code: 
linux-hjs1:/home/josgoe # lspci -vv
00:00.0 Host bridge: Intel Corporation Eaglelake DRAM Controller (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 82d3
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information <?>

00:01.0 PCI bridge: Intel Corporation Eaglelake PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: fa000000-fe8fffff
        Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [88] Subsystem: ASUSTeK Computer Inc. Device 82d3
        Capabilities: [80] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
                Address: fee0300c  Data: 41b9
        Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot+
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  0, PowerLimit 75.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Kernel driver in use: pcieport-driver
        Kernel modules: shpchp

00:1a.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #4 (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at a800 [size=32]
        Capabilities: [50] Vendor Specific Information <?>
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1a.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #5 (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at a880 [size=32]
        Capabilities: [50] Vendor Specific Information <?>
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1a.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #6 (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at ac00 [size=32]
        Capabilities: [50] Vendor Specific Information <?>
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1a.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller #2 (prog-if 20 [EHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 0: Memory at f9fffc00 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port: BAR=1 offset=00a0
        Capabilities: [98] Vendor Specific Information <?>
        Kernel driver in use: ehci_hcd
        Kernel modules: ehci-hcd

00:1b.0 Audio device: Intel Corporation ICH10 HD Audio Controller
        Subsystem: ASUSTeK Computer Inc. Device 82fe
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at f9ff8000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE- FLReset+
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
        Kernel driver in use: HDA Intel
        Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation ICH10 PCI Express Port 1 (prog-if 00 [Normal decode])
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        Prefetchable memory behind bridge: 00000000f8f00000-00000000f8ffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot #  0, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
                Address: fee0300c  Data: 41c1
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d4
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport-driver
        Kernel modules: shpchp

00:1c.4 PCI bridge: Intel Corporation ICH10 PCI Express Port 5 (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: fea00000-feafffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot #  0, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
                Address: fee0300c  Data: 41c9
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d4
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport-driver
        Kernel modules: shpchp

00:1c.5 PCI bridge: Intel Corporation ICH10 PCI Express Port 6 (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: fe900000-fe9fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot #  0, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
                Address: fee0300c  Data: 41d1
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d4
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pcieport-driver
        Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #1 (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 23
        Region 4: I/O ports at a080 [size=32]
        Capabilities: [50] Vendor Specific Information <?>
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #2 (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 4: I/O ports at a400 [size=32]
        Capabilities: [50] Vendor Specific Information <?>
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #3 (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at a480 [size=32]
        Capabilities: [50] Vendor Specific Information <?>
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller #1 (prog-if 20 [EHCI])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at f9fff800 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port: BAR=1 offset=00a0
        Capabilities: [98] Vendor Specific Information <?>
        Kernel driver in use: ehci_hcd
        Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: feb00000-febfffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 82d4

00:1f.0 ISA bridge: Intel Corporation ICH10 LPC Interface Controller
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information <?>

00:1f.2 IDE interface: Intel Corporation ICH10 4 port SATA IDE Controller (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 0: I/O ports at 9000 [size=8]
        Region 1: I/O ports at 8c00 [size=4]
        Region 2: I/O ports at 8880 [size=8]
        Region 3: I/O ports at 8800 [size=4]
        Region 4: I/O ports at 8480 [size=16]
        Region 5: I/O ports at 8400 [size=16]
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [b0] Vendor Specific Information <?>
        Kernel driver in use: ata_piix
        Kernel modules: ata_piix

00:1f.3 SMBus: Intel Corporation ICH10 SMBus Controller
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin C routed to IRQ 18
        Region 0: Memory at f9fff400 (64-bit, non-prefetchable) [size=256]
        Region 4: I/O ports at 0400 [size=32]
        Kernel driver in use: i801_smbus
        Kernel modules: i2c-i801

00:1f.5 IDE interface: Intel Corporation ICH10 2 port SATA IDE Controller (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. Device 82d4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 0: I/O ports at a000 [size=8]
        Region 1: I/O ports at 9c00 [size=4]
        Region 2: I/O ports at 9880 [size=8]
        Region 3: I/O ports at 9800 [size=4]
        Region 4: I/O ports at 9480 [size=16]
        Region 5: I/O ports at 9400 [size=16]
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [b0] Vendor Specific Information <?>
        Kernel driver in use: ata_piix
        Kernel modules: ata_piix

01:00.0 VGA compatible controller: nVidia Corporation Device 0640 (rev a1) (prog-if 00 [VGA controller])
        Subsystem: ASUSTeK Computer Inc. Device 8299
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
        Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
        Region 5: I/O ports at bc00 [size=128]
        [virtual] Expansion ROM at fe880000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [78] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <1us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [b4] Vendor Specific Information <?>
        Kernel driver in use: nvidia
        Kernel modules: nvidiafb

02:00.0 Ethernet controller: Attansic Technology Corp. Device 1026 (rev b0)
        Subsystem: ASUSTeK Computer Inc. Device 8226
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at fe9c0000 (64-bit, non-prefetchable) [size=256K]
        Region 2: I/O ports at cc00 [size=128]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [58] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
                        ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

03:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II Controller (rev b2) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: ASUSTeK Computer Inc. Device 82e0
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at dc00 [size=8]
        Region 1: I/O ports at d880 [size=4]
        Region 2: I/O ports at d800 [size=8]
        Region 3: I/O ports at d480 [size=4]
        Region 4: I/O ports at d400 [size=16]
        Region 5: Memory at feaffc00 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 unlimited
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Kernel driver in use: pata_marvell
        Kernel modules: pata_marvell, ahci

05:00.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
        Subsystem: Technotrend Systemtechnik GmbH Device 000e
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64 (3750ns min, 9500ns max)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=512]
        Kernel driver in use: dvb
        Kernel modules: dvb-ttpci

05:01.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
        Subsystem: D-Link System Inc DFE-528TX 10/100 Fast Ethernet PCI Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at e800 [size=256]
        Region 1: Memory at febff800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: 8139too
        Kernel modules: 8139too

05:03.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70) (prog-if 10 [OHCI])
        Subsystem: ASUSTeK Computer Inc. Device 8294
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+
        Kernel driver in use: ohci1394
        Kernel modules: ohci1394

linux-hjs1:/home/josgoe #

So ich hoffe, das entspricht dem was Du mir aufgetragen hast.

Gruß

Josef
 
S

spoensche

Moderator
Teammitglied
Laut der Ausgabe von ifconfig funktioniert deine Karte doch. Sie hat vom Router eine IP bekommen, keine Fehler beim senden und empfangen.

Warum du die Karte mit Yast nicht konfigurieren kannst, ist mir schleierhaft. Was zeigt dir Yast den an, wenn du auf die Netzwerkgeräte gehst? In der Spalte "Name" sollte der Name deiner Karte stehen und in der Spalte "IP- Adresse" sollte DHCP oder bei fester IP- Vergabe die IP der Karte stehen.
 
OP
J

jgoe1

Member
Hallo Spoensche,
Damit wir uns richtig verstehehn, die Ethernetkarte ist konfiguriert und Funktioniert. Es geht um den Onboard "Attasic"-Controller und dazu kopiere ich Dir hier die Ausgabe von Yast.

Code: 
Attansic Ethernet controller (Nicht verbunden)
BusID : 0000:02:00.0

Konfiguration der Netzwerkkarte nicht möglich, weil das Kernel-Gerät (eth0, wlan0) nicht verfügbar ist. Dies wird zumeist durch fehlende Firmware (für WLAN-Geräte) verursacht. Zu Einzelheiten s. die dmesg-Ausgabe.

Die Ausgabe von "dmseg" ist Ellen lang, kann ich aber auch senden.

Danke und Gruß

Josef
 
OP
J

jgoe1

Member
Hallo Grothesk, Hallo Spoensche und allen die mich unterstützt haben sei Dank. Ich hatte selber schon nach Treibern gesucht und warum nicht gefunden? Es ist richtig spontan abgelaufen, installieren, konfigurieren, auf eth0 umfirmiert und alles läuft. Spitze! Jetzt habe ich wieder einen PCI-Steckplatz frei.

Danke und Gruß

Josef :up:
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben