• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

OpenSuse 11 und FritzStick

ExAzubi

Newbie
Hallo zusammen,

nach langer Zeit meiner Linux abstinenz habe mich nun zum 5 Versuch durchgerungen, meinen PC mit Linux ans fliegen zu kriegen.

Nun aber zu meinem Problem:

Ich habe per ndiswrapper meinen FritzStick installiert; soweit so gut.
Dieser wird auch erkannt, und mit iwlist wlan0 scan bekomme ich auch immer alle AP meiner Umgebung aufgelistet.
Auch mit ifconfig erscheint meine wlan Schnittstelle.

Nur Netzwerk ist noch immer nicht :(

Ich bin nur für Sekunden im Netzwerk und dann anschließend wieder für Minuten nicht. Anbei seht Ihr zwei iwconfig Auflistungen, die das Problem hoffentlich genug beschreiben.

Verbunden:

wlan0 IEEE 802.11g ESSID:"Heimat"
Mode:Managed Frequency:2.437 GHz Access Point: 00:1D:7E:18:E8:B7
Bit Rate=54 Mb/s Tx-Power:10 dBm Sensitivity=0/3
RTS thr:eek:ff Fragment thr:eek:ff
Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX
Security mode:restricted
Power Management:eek:ff
Link Quality:100/100 Signal level:-60 dBm Noise level:-96 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

Nicht verbunden:

wlan0 Auto Access Point: Not-Associated Bit Rate:0 kb/s
Link Quality:100/100 Signal level:-60 dBm Noise level:-96 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0


Wie gesagt, ich bin immer nur für wenige Sekunden im Netz (komme dann auch ins Internet) anschließend bin ich wieder raus.

Was kann ich machen, da ich immer im Netz bin?

WPA-TKIP Verschlüsselung, kein DHCP.

OpenSuse Version aus c't Spezial Ausgabe.

Danke an alle Helfenden.
 

lOtz1009

Moderator
Teammitglied
Sind die restlichen Chipsatztreiber auf der Blacklist?
Poste doch mal bitte die Ausgabe von http://www.linux-club.de/viewtopic.php?f=19&t=93338
 
OP
E

ExAzubi

Newbie
Hallo gesagt -> getan ;)

Folgend die Ausgabe:


In den ersten ca. 5 Minuten nach dem Booten habe ich eine Netzwerkverbindung, kann sogar surfen, erst danach bin ich wieder von der Außenwelt (Netzwerk) abgeschnitten.


Code:
collectNWData.sh V0.6d-3
--- Welcher Netzwerkverbindungtyp soll getestet werden?
--- (2) Kabellose Verbindung (WLAN)
--- Welche Netzwerktopologie liegt vor?
--- (2) WLAN HW router <---> LinuxClient
--- Auf welchem Rechner wird das Script ausgeführt?
--- (1) LinuxClient

==================================================================================================
==================================================================================================
*** uname -a 
Linux linux 2.6.25.5-1.1-pae #1 SMP 2008-06-07 01:55:22 +0200 i686 athlon i386 GNU/Linux
==================================================================================================
*** cat /etc/SuSE-release 
openSUSE 11.0 (i586)
VERSION = 11.0
==================================================================================================
*** cat /etc/resolv.conf | /usr/bin/grep -v "^#" | /usr/bin/grep -v "^$" 
nameserver 192.168.178.1
search site
==================================================================================================
*** cat /etc/hosts | grep -v "^#" | /usr/bin/grep -v "^$" | /usr/bin/grep -v "::" 
127.0.0.1       localhost
127.0.0.2       linux.site linux
192.168.178.20  Linux Linux
==================================================================================================
*** cat /proc/sys/net/ipv4/ip_forward 
0
==================================================================================================
*** /usr/sbin/iptables -t nat -L 
Chain PREROUTING (policy ACCEPT)
target     prot opt source               destination         

Chain POSTROUTING (policy ACCEPT)
target     prot opt source               destination         

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination         
==================================================================================================
*** /sbin/route -n 
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
192.168.178.0   0.0.0.0         255.255.255.0   U     0      0        0 wlan0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 wlan0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.178.1   0.0.0.0         UG    0      0        0 wlan0
==================================================================================================
*** /sbin/arp -n 
Address                  HWtype  HWaddress           Flags Mask            Iface
192.168.178.1                    (unvollsändig)                           wlan0
==================================================================================================
*** /sbin/ifconfig 
lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:123 errors:0 dropped:0 overruns:0 frame:0
          TX packets:123 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:8571 (8.3 Kb)  TX bytes:8571 (8.3 Kb)

wlan0     Link encap:Ethernet  Hardware Adresse 00:04:0E:C8:4A:E5  
          inet Adresse:192.168.178.20  Bcast:192.168.178.255  Maske:255.255.255.0
          inet6 Adresse: fe80::204:eff:fec8:4ae5/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5977 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4227 errors:0 dropped:18 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:7544551 (7.1 Mb)  TX bytes:354078 (345.7 Kb)

==================================================================================================
*** /sbin/lspci -nn | /usr/bin/egrep '(Ethernet|Network).*controller' 
==================================================================================================
*** /usr/bin/lsusb 
Bus 002 Device 002: ID 045e:008a Microsoft Corp. Wireless Keyboard and Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 005: ID 057c:6201 AVM GmbH WLAN USB v1.1
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
==================================================================================================
*** /sbin/lsmod | /usr/bin/sort 
ac97_bus               18304  1 snd_ac97_codec
acx                   161416  0 
af_packet              38656  2 
binfmt_misc            28040  1 
button                 25360  0 
cdrom                  50588  1 sr_mod
cpufreq_conservative    24456  0 
cpufreq_powersave      18176  0 
cpufreq_userspace      22660  0 
dm_mod                 78676  0 
dock                   27536  1 libata
edd                    26440  0 
ehci_hcd               52492  0 
ext3                  155784  2 
fan                    22660  0 
fat                    66720  1 vfat
ff_memless             21896  1 usbhid
firmware_class         25984  2 acx,snd_emu10k1
forcedeth              67340  0 
fuse                   66332  11 
hid                    53708  1 usbhid
i2c_core               41108  1 i2c_nforce2
i2c_nforce2            23296  0 
ieee1394              107016  1 ohci1394
ip6table_filter        19712  0 
ip6_tables             31376  1 ip6table_filter
iptable_filter         19840  0 
iptable_nat            23688  0 
ip_tables              30224  2 iptable_nat,iptable_filter
ipv6                  281064  12 
jbd                    73376  1 ext3
k8temp                 22016  0 
libata                176220  2 pata_amd,sata_nv
loop                   35332  0 
mbcache                25348  1 ext3
Module                  Size  Used by
ndiswrapper           214420  0 
nf_conntrack           79188  3 iptable_nat,nf_nat,nf_conntrack_ipv4
nf_conntrack_ipv4      27652  3 iptable_nat,nf_nat
nf_nat                 35736  1 iptable_nat
nls_cp437              22144  0 
nls_iso8859_1          20480  0 
ohci1394               48432  0 
ohci_hcd               39940  0 
parport                52948  2 ppdev,parport_pc
parport_pc             55100  0 
pata_amd               30084  0 
powernow_k8            31748  0 
ppdev                  25348  0 
processor              67504  2 powernow_k8,thermal
rtc_cmos               27168  0 
rtc_core               37148  1 rtc_cmos
rtc_lib                19328  1 rtc_core
sata_nv                42764  8 
scsi_mod              168308  5 usb_storage,sg,sr_mod,sd_mod,libata
sd_mod                 45208  10 
sg                     52020  0 
snd                    79544  18 snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_util_mem,snd_hwdep
snd_ac97_codec        120868  1 snd_emu10k1
snd_emu10k1           162948  2 snd_emu10k1_synth
snd_emu10k1_synth      24832  0 
snd_emux_synth         54272  1 snd_emu10k1_synth
snd_hwdep              26372  2 snd_emux_synth,snd_emu10k1
snd_mixer_oss          33408  1 snd_pcm_oss
snd_page_alloc         27400  2 snd_emu10k1,snd_pcm
snd_pcm               100100  3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_pcm_oss            64256  0 
snd_rawmidi            42496  3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1
snd_seq                73664  5 snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_event,snd_seq_midi_emul
snd_seq_device         25100  6 snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq,snd_emu10k1,snd_rawmidi
snd_seq_midi           26112  0 
snd_seq_midi_emul      22784  1 snd_emux_synth
snd_seq_midi_event     23936  2 snd_seq_midi,snd_seq_virmidi
snd_seq_virmidi        23680  1 snd_emux_synth
snd_timer              40712  3 snd_seq,snd_emu10k1,snd_pcm
snd_util_mem           21632  2 snd_emux_synth,snd_emu10k1
soundcore              24264  1 snd
sr_mod                 33320  0 
thermal                39452  0 
usbcore               164684  7 acx,usb_storage,ndiswrapper,usbhid,ohci_hcd,ehci_hcd
usbhid                 60260  0 
usb_storage           100744  0 
vfat                   28800  0 
x_tables               33668  3 iptable_nat,ip_tables,ip6_tables
==================================================================================================
*** catMyConfig 
==================================================================================================
*** cat /etc/sysconfig/network/ifcfg-wlan0
BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR='192.168.178.20/24'
MTU=''
NAME='WLAN USB Device'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='auto'
USERCONTROL='no'
WIRELESS_AP=''
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_CA_CERT=''
WIRELESS_CHANNEL=''
WIRELESS_CLIENT_CERT=''
WIRELESS_CLIENT_KEY=''
WIRELESS_CLIENT_KEY_PASSWORD=''
WIRELESS_DEFAULT_KEY='0'
WIRELESS_EAP_AUTH=''
WIRELESS_EAP_MODE=''
WIRELESS_ESSID='Heimat'
WIRELESS_FREQUENCY=''
WIRELESS_KEY=''
WIRELESS_KEY_0=''
WIRELESS_KEY_1=''
WIRELESS_KEY_2=''
WIRELESS_KEY_3=''
WIRELESS_KEY_LENGTH='128'
WIRELESS_MODE='Managed'
WIRELESS_NICK=''
WIRELESS_NWID=''
WIRELESS_PEAP_VERSION=''
WIRELESS_POWER='no'
WIRELESS_WPA_ANONID=''
WIRELESS_WPA_IDENTITY=''
WIRELESS_WPA_PASSWORD=''
WIRELESS_WPA_PSK='@@@@@@'
==================================================================================================
*** /usr/sbin/iwconfig | /usr/bin/sed "s/\(Encryption key:\)\([^o][^f][^f][^ ]*\)\(.*\)/\1@@ @@@-@@@@-@@@@-@@@@-@@@@-@@@@@@@\3/" 
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:"Heimat"  
          Mode:Managed  Frequency:2.437 GHz  Access Point: 00:1D:7E:18:E8:B7   
          Bit Rate=54 Mb/s   Tx-Power:10 dBm   Sensitivity=0/3  
          RTS thr:off   Fragment thr:off
          Encryption key:@@ @@@-@@@@-@@@@-@@@@-@@@@-@@@@@@@   Security mode:restricted
          Power Management:off
          Link Quality:51/100  Signal level:-63 dBm  Noise level:-96 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

==================================================================================================
*** /usr/bin/grep -i radio /var/log/boot.msg | /usr/bin/tail -n 5 
==================================================================================================
*** /usr/bin/grep -i firmware /var/log/messages* | /usr/bin/tail -n 5 
Jul 14 20:23:40 linux kernel: requesting firmware image 'tiacx111usbc1B'
Jul 14 20:23:40 linux kernel: acx: firmware image 'tiacx111usbc1B' was not provided. Check your hotplug scripts
Jul 14 20:23:41 linux firmware.sh[5062]: Cannot find  firmware file 'tiacx111usbc1B'
Jul 14 20:31:16 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
Jul 15 19:16:07 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
==================================================================================================
*** ls -ls /lib/firmware 
insgesamt 448
  4 -rw-r--r-- 1 root root  3408  6. Jun 22:18 aica_firmware.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 asihpi
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 digiface_firmware.bin
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 digiface_firmware_rev11.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 ea
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 emagic
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 emu
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 ess
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 korg
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 mixart
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 multiface_firmware.bin
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 multiface_firmware_rev11.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 pcxhr
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 sb16
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 vx
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 yamaha
==================================================================================================
*** ps aux | /usr/bin/grep wpa_supplicant | /usr/bin/grep -v grep 
root      3530  0.0  0.0   3856   840 ?        S<s  19:16   0:00 wpa_supplicant -iwlan0 -c/var/run/wpa_supplicant-wlan0.conf -Dwext -P/var/run/wpa_supplicant/wlan0.pid -B
==================================================================================================
*** /usr/bin/grep NETWORKMANAGER /etc/sysconfig/network/config | /usr/bin/grep -v "^#" 
NETWORKMANAGER=no
==================================================================================================
*** /usr/bin/grep -i persistent /etc/sysconfig/network/config | /usr/bin/grep -v "^#" | /usr/bin/grep -v "^$" 
==================================================================================================
*** /usr/bin/egrep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/70-persistent-net* | /usr/bin/grep -v ":#" | grep -v ":$" 
/usr/bin/egrep: /etc/udev/rules.d/*net_persistent*: Datei oder Verzeichnis nicht gefunden
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:04:0e:c8:4a:e5", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0f:ea:31:80:35", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
==================================================================================================
*** /usr/bin/egrep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*|/usr/bin/egrep -v '#|blacklist' 
/etc/modprobe.conf:install eth0             /bin/true
/etc/modprobe.conf:install eth1             /bin/true
/etc/modprobe.d/ndiswrapper:alias wlan0 ndiswrapper
==================================================================================================
*** detectFirmwareMessages 
Jul 15 19:16:07 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
Jul 15 19:16:07 linux kernel: acx: running on a little-endian CPU
Jul 15 19:16:07 linux kernel: acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe...
Jul 15 19:16:07 linux kernel: USB module v0.3.37 initialized, probing for devices...
Jul 15 19:16:07 linux kernel: usb 1-5: reset high speed USB device using ehci_hcd and address 5
---------------------------------------------------------------------------
==================================================================================================
*** detectAPs
 

lOtz1009

Moderator
Teammitglied
Also ndiswrapper oder AVM-Treiber?

Bei ersterem die acx-Pakete deinstallieren und acx auf die Blacklist setzen.
Code:
ndiswrapper -l
bei eingestecktem Stick sollte dir zeigen ob der Treiber auch installiert ist.
 
OP
E

ExAzubi

Newbie
Danke an alle Helfenden.

Wie setze ich den acx auf die Blacklist? Absoluter Anfänger:(

Anbei die Ausgabe, wenn ich im Netz bin, also den ersten 5 Minuten. Ich habe einen Unterschied im Bereich Firmware festgestellt.

Im Fehlerfall steht da was von
acx: firmware image 'tiacx111usbc1B' was not provided. Check your hotplug scripts

Hier nun der Text.

Code:
collectNWData.sh V0.6d-3
--- Welcher Netzwerkverbindungtyp soll getestet werden?
--- (2) Kabellose Verbindung (WLAN)
--- Welche Netzwerktopologie liegt vor?
--- (2) WLAN HW router <---> LinuxClient
--- Auf welchem Rechner wird das Script ausgeführt?
--- (1) LinuxClient

==================================================================================================
==================================================================================================
*** uname -a 
Linux linux 2.6.25.5-1.1-pae #1 SMP 2008-06-07 01:55:22 +0200 i686 athlon i386 GNU/Linux
==================================================================================================
*** cat /etc/SuSE-release 
openSUSE 11.0 (i586)
VERSION = 11.0
==================================================================================================
*** cat /etc/resolv.conf | /usr/bin/grep -v "^#" | /usr/bin/grep -v "^$" 
nameserver 192.168.178.1
search site
==================================================================================================
*** cat /etc/hosts | grep -v "^#" | /usr/bin/grep -v "^$" | /usr/bin/grep -v "::" 
127.0.0.1       localhost
127.0.0.2       linux.site linux
192.168.178.20  Linux Linux
==================================================================================================
*** cat /proc/sys/net/ipv4/ip_forward 
0
==================================================================================================
*** /usr/sbin/iptables -t nat -L 
Chain PREROUTING (policy ACCEPT)
target     prot opt source               destination         

Chain POSTROUTING (policy ACCEPT)
target     prot opt source               destination         

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination         
==================================================================================================
*** /sbin/route -n 
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
192.168.178.0   0.0.0.0         255.255.255.0   U     0      0        0 wlan0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 wlan0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.178.1   0.0.0.0         UG    0      0        0 wlan0
==================================================================================================
*** /sbin/arp -n 
Address                  HWtype  HWaddress           Flags Mask            Iface
192.168.178.1            ether   00:1D:7E:18:E8:B5   C                     wlan0
==================================================================================================
*** /sbin/ifconfig 
lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:42 errors:0 dropped:0 overruns:0 frame:0
          TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:2708 (2.6 Kb)  TX bytes:2708 (2.6 Kb)

wlan0     Link encap:Ethernet  Hardware Adresse 00:04:0E:C8:4A:E5  
          inet Adresse:192.168.178.20  Bcast:192.168.178.255  Maske:255.255.255.0
          inet6 Adresse: fe80::204:eff:fec8:4ae5/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:13 errors:0 dropped:0 overruns:0 frame:0
          TX packets:19 errors:0 dropped:13 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:1444 (1.4 Kb)  TX bytes:1883 (1.8 Kb)

==================================================================================================
*** /sbin/lspci -nn | /usr/bin/egrep '(Ethernet|Network).*controller' 
==================================================================================================
*** /usr/bin/lsusb 
Bus 002 Device 002: ID 057c:6201 AVM GmbH WLAN USB v1.1
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 045e:008a Microsoft Corp. Wireless Keyboard and Mouse
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
==================================================================================================
*** /sbin/lsmod | /usr/bin/sort 
ac97_bus               18304  1 snd_ac97_codec
acx                   161416  0 
af_packet              38656  2 
binfmt_misc            28040  1 
button                 25360  0 
cdrom                  50588  1 sr_mod
cpufreq_conservative    24456  0 
cpufreq_powersave      18176  0 
cpufreq_userspace      22660  0 
dm_mod                 78676  0 
dock                   27536  1 libata
edd                    26440  0 
ehci_hcd               52492  0 
ext3                  155784  2 
fan                    22660  0 
ff_memless             21896  1 usbhid
firmware_class         25984  2 snd_emu10k1,acx
forcedeth              67340  0 
fuse                   66332  11 
hid                    53708  1 usbhid
i2c_core               41108  1 i2c_nforce2
i2c_nforce2            23296  0 
ieee1394              107016  1 ohci1394
ip6table_filter        19712  0 
ip6_tables             31376  1 ip6table_filter
iptable_filter         19840  0 
iptable_nat            23688  0 
ip_tables              30224  2 iptable_nat,iptable_filter
ipv6                  281064  12 
jbd                    73376  1 ext3
k8temp                 22016  0 
libata                176220  2 pata_amd,sata_nv
loop                   35332  0 
mbcache                25348  1 ext3
Module                  Size  Used by
ndiswrapper           214420  0 
nf_conntrack           79188  3 iptable_nat,nf_nat,nf_conntrack_ipv4
nf_conntrack_ipv4      27652  3 iptable_nat,nf_nat
nf_nat                 35736  1 iptable_nat
ohci1394               48432  0 
ohci_hcd               39940  0 
parport                52948  2 ppdev,parport_pc
parport_pc             55100  0 
pata_amd               30084  0 
powernow_k8            31748  0 
ppdev                  25348  0 
processor              67504  2 powernow_k8,thermal
rtc_cmos               27168  0 
rtc_core               37148  1 rtc_cmos
rtc_lib                19328  1 rtc_core
sata_nv                42764  8 
scsi_mod              168308  5 sr_mod,usb_storage,sg,sd_mod,libata
sd_mod                 45208  10 
sg                     52020  0 
snd                    79544  18 snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_util_mem,snd_hwdep
snd_ac97_codec        120868  1 snd_emu10k1
snd_emu10k1           162948  2 snd_emu10k1_synth
snd_emu10k1_synth      24832  0 
snd_emux_synth         54272  1 snd_emu10k1_synth
snd_hwdep              26372  2 snd_emux_synth,snd_emu10k1
snd_mixer_oss          33408  1 snd_pcm_oss
snd_page_alloc         27400  2 snd_emu10k1,snd_pcm
snd_pcm               100100  3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_pcm_oss            64256  0 
snd_rawmidi            42496  3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1
snd_seq                73664  5 snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_event,snd_seq_midi_emul
snd_seq_device         25100  6 snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq,snd_emu10k1,snd_rawmidi
snd_seq_midi           26112  0 
snd_seq_midi_emul      22784  1 snd_emux_synth
snd_seq_midi_event     23936  2 snd_seq_midi,snd_seq_virmidi
snd_seq_virmidi        23680  1 snd_emux_synth
snd_timer              40712  3 snd_seq,snd_emu10k1,snd_pcm
snd_util_mem           21632  2 snd_emux_synth,snd_emu10k1
soundcore              24264  1 snd
sr_mod                 33320  0 
thermal                39452  0 
usbcore               164684  7 ndiswrapper,acx,usbhid,usb_storage,ehci_hcd,ohci_hcd
usbhid                 60260  0 
usb_storage           100744  0 
x_tables               33668  3 iptable_nat,ip_tables,ip6_tables
==================================================================================================
*** catMyConfig 
==================================================================================================
*** cat /etc/sysconfig/network/ifcfg-wlan0
BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR='192.168.178.20/24'
MTU=''
NAME='WLAN USB Device'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='auto'
USERCONTROL='no'
WIRELESS_AP=''
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_CA_CERT=''
WIRELESS_CHANNEL=''
WIRELESS_CLIENT_CERT=''
WIRELESS_CLIENT_KEY=''
WIRELESS_CLIENT_KEY_PASSWORD=''
WIRELESS_DEFAULT_KEY='0'
WIRELESS_EAP_AUTH=''
WIRELESS_EAP_MODE=''
WIRELESS_ESSID='Heimat'
WIRELESS_FREQUENCY=''
WIRELESS_KEY=''
WIRELESS_KEY_0=''
WIRELESS_KEY_1=''
WIRELESS_KEY_2=''
WIRELESS_KEY_3=''
WIRELESS_KEY_LENGTH='128'
WIRELESS_MODE='Managed'
WIRELESS_NICK=''
WIRELESS_NWID=''
WIRELESS_PEAP_VERSION=''
WIRELESS_POWER='no'
WIRELESS_WPA_ANONID=''
WIRELESS_WPA_IDENTITY=''
WIRELESS_WPA_PASSWORD=''
WIRELESS_WPA_PSK='@@@@@@'
==================================================================================================
*** /usr/sbin/iwconfig | /usr/bin/sed "s/\(Encryption key:\)\([^o][^f][^f][^ ]*\)\(.*\)/\1@@ @@@-@@@@-@@@@-@@@@-@@@@-@@@@@@@\3/" 
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:"Heimat"  
          Mode:Managed  Frequency:2.437 GHz  Access Point: 00:1D:7E:18:E8:B7   
          Bit Rate=54 Mb/s   Tx-Power:10 dBm   Sensitivity=0/3  
          RTS thr:off   Fragment thr:off
          Encryption key:@@ @@@-@@@@-@@@@-@@@@-@@@@-@@@@@@@   Security mode:restricted
          Power Management:off
          Link Quality:46/100  Signal level:-66 dBm  Noise level:-96 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

==================================================================================================
*** /usr/bin/grep -i radio /var/log/boot.msg | /usr/bin/tail -n 5 
==================================================================================================
*** /usr/bin/grep -i firmware /var/log/messages* | /usr/bin/tail -n 5 
Jul 14 20:23:40 linux kernel: requesting firmware image 'tiacx111usbc1B'
Jul 14 20:23:40 linux kernel: acx: firmware image 'tiacx111usbc1B' was not provided. Check your hotplug scripts
Jul 14 20:23:41 linux firmware.sh[5062]: Cannot find  firmware file 'tiacx111usbc1B'
Jul 14 20:31:16 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
Jul 15 19:16:07 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
==================================================================================================
*** ls -ls /lib/firmware 
insgesamt 448
  4 -rw-r--r-- 1 root root  3408  6. Jun 22:18 aica_firmware.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 asihpi
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 digiface_firmware.bin
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 digiface_firmware_rev11.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 ea
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 emagic
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 emu
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 ess
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 korg
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 mixart
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 multiface_firmware.bin
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 multiface_firmware_rev11.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 pcxhr
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 sb16
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 vx
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 yamaha
==================================================================================================
*** ps aux | /usr/bin/grep wpa_supplicant | /usr/bin/grep -v grep 
root      2585  0.0  0.0   3856   876 ?        Ss   20:00   0:00 wpa_supplicant -iwlan0 -c/var/run/wpa_supplicant-wlan0.conf -Dwext -P/var/run/wpa_supplicant/wlan0.pid -B
==================================================================================================
*** /usr/bin/grep NETWORKMANAGER /etc/sysconfig/network/config | /usr/bin/grep -v "^#" 
NETWORKMANAGER=no
==================================================================================================
*** /usr/bin/grep -i persistent /etc/sysconfig/network/config | /usr/bin/grep -v "^#" | /usr/bin/grep -v "^$" 
==================================================================================================
*** /usr/bin/egrep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/70-persistent-net* | /usr/bin/grep -v ":#" | grep -v ":$" 
/usr/bin/egrep: /etc/udev/rules.d/*net_persistent*: Datei oder Verzeichnis nicht gefunden
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:04:0e:c8:4a:e5", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0f:ea:31:80:35", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
==================================================================================================
*** /usr/bin/egrep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*|/usr/bin/egrep -v '#|blacklist' 
/etc/modprobe.conf:install eth0             /bin/true
/etc/modprobe.conf:install eth1             /bin/true
/etc/modprobe.d/ndiswrapper:alias wlan0 ndiswrapper
==================================================================================================
*** detectFirmwareMessages 
Jul 15 19:16:07 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
Jul 15 19:16:07 linux kernel: acx: running on a little-endian CPU
Jul 15 19:16:07 linux kernel: acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe...
Jul 15 19:16:07 linux kernel: USB module v0.3.37 initialized, probing for devices...
Jul 15 19:16:07 linux kernel: usb 1-5: reset high speed USB device using ehci_hcd and address 5
---------------------------------------------------------------------------
==================================================================================================
*** detectAPs
 
OP
E

ExAzubi

Newbie
Hallo gesagt getan,

aber leider immer noch keine Verbesserung, die ersten 5 Min nach dem booten bin ich im Netz, danach ist der Stick tot, nur noch die USB Leuchte leuchtet noch.

Was wäre denn dann der nächste Schritt.

Ich meine auch das Ihm der Blacklist Eintrag ziemlic egal war, da immer noch in den Messages die Nachricht auftaucht.

acx running on a little endian CPU.

Auch in der YAST Netzwerkconfig steht als Modulname noch acx .

Was kann es sein?
 

Grothesk

Ultimate Guru
Dann schmeiß den acx doch auch im yast raus.
Und wie sieht der Eintrag in welcher Datei nun genau aus?
Und bitte das skript jedesmal neu ausführen und nach http://phpfi.com kopieren.
Dann kann man genau sehen, was da z. B. geladen ist.
 
OP
E

ExAzubi

Newbie
Hallo,

habe die acx Komponenten in YAST deinstalliert, nun bootet aber mein System nicht :(

Dieser bleibt immer bei ETC/Init.d./boot.local hängen. Dort habe ich eigentlich nur den Eintrag "modprobe ndiswrapper" eingetragen. Werde heute mal im abgesicherten Modus booten und dann den Eintrag entfernen.
 

blacklips

Hacker
ndiswrapper muss dort nicht eingetragen werden. Für das laden von ndiswrapper gibt es die
ndiswrapper -m -mi -ma Optionen dann sollte ndiswrapper geladen werden.
P.S. Bei mir funktioniert der einwandfrei mit ndiswrapper unter einem 2.6.25-Kernel.
 
OP
E

ExAzubi

Newbie
Hallo zusammen,

was habe ich heute abend versucht, damit der Stick fliegt.

1. modprobe ndiswrapper aus der boot.local ausgetragen
2. ndiswrapper -r fwlan eingegeben
3. WLAN USB Device aus der YAST configuration gelöscht.
4. ndiswrapper -i fwlan.inf erneut installiert
5. WLAN USB Device im YAST konfiguriert
6. Reboot.

Dann war nach ca. 1 Minute der Stick zum surfen da! Aber leider wieder nur für gute 5 Minuten :(

CollectNWData laufen lassen, das Ergebnis seht ihr hier. Sollte ich vielleicht bis OpenSuse12 warten?

Code:
collectNWData.sh V0.6d-3
--- Welcher Netzwerkverbindungtyp soll getestet werden?
--- (2) Kabellose Verbindung (WLAN)
--- Welche Netzwerktopologie liegt vor?
--- (2) WLAN HW router <---> LinuxClient
--- Auf welchem Rechner wird das Script ausgeführt?
--- (1) LinuxClient

==================================================================================================
==================================================================================================
*** uname -a 
Linux linux 2.6.25.5-1.1-pae #1 SMP 2008-06-07 01:55:22 +0200 i686 athlon i386 GNU/Linux
==================================================================================================
*** cat /etc/SuSE-release 
openSUSE 11.0 (i586)
VERSION = 11.0
==================================================================================================
*** cat /etc/resolv.conf | /usr/bin/grep -v "^#" | /usr/bin/grep -v "^$" 
nameserver 192.168.178.1
search site
==================================================================================================
*** cat /etc/hosts | grep -v "^#" | /usr/bin/grep -v "^$" | /usr/bin/grep -v "::" 
127.0.0.1       localhost
127.0.0.2       linux.site linux
192.168.178.20  Linux Linux
192.168.178.20  Linux Linux
==================================================================================================
*** cat /proc/sys/net/ipv4/ip_forward 
0
==================================================================================================
*** /usr/sbin/iptables -t nat -L 
Chain PREROUTING (policy ACCEPT)
target     prot opt source               destination         

Chain POSTROUTING (policy ACCEPT)
target     prot opt source               destination         

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination         
==================================================================================================
*** /sbin/route -n 
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
192.168.178.0   0.0.0.0         255.255.255.0   U     0      0        0 wlan0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 wlan0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.178.1   0.0.0.0         UG    0      0        0 wlan0
==================================================================================================
*** /sbin/arp -n 
Address                  HWtype  HWaddress           Flags Mask            Iface
192.168.178.1                    (unvollsändig)                           wlan0
==================================================================================================
*** /sbin/ifconfig 
lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:83 errors:0 dropped:0 overruns:0 frame:0
          TX packets:83 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:6512 (6.3 Kb)  TX bytes:6512 (6.3 Kb)

wlan0     Link encap:Ethernet  Hardware Adresse 00:04:0E:C8:4A:E5  
          inet Adresse:192.168.178.20  Bcast:192.168.178.255  Maske:255.255.255.0
          inet6 Adresse: fe80::204:eff:fec8:4ae5/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8639 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5298 errors:0 dropped:25 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:12198331 (11.6 Mb)  TX bytes:368031 (359.4 Kb)

==================================================================================================
*** /sbin/lspci -nn | /usr/bin/egrep '(Ethernet|Network).*controller' 
==================================================================================================
*** /usr/bin/lsusb 
Bus 002 Device 002: ID 057c:6201 AVM GmbH WLAN USB v1.1
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 045e:008a Microsoft Corp. Wireless Keyboard and Mouse
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
==================================================================================================
*** /sbin/lsmod | /usr/bin/sort 
ac97_bus               18304  1 snd_ac97_codec
af_packet              38656  2 
binfmt_misc            28040  1 
button                 25360  0 
cdrom                  50588  1 sr_mod
cpufreq_conservative    24456  0 
cpufreq_powersave      18176  0 
cpufreq_userspace      22660  0 
dm_mod                 78676  0 
dock                   27536  1 libata
edd                    26440  0 
ehci_hcd               52492  0 
ext3                  155784  2 
fan                    22660  0 
ff_memless             21896  1 usbhid
firmware_class         25984  1 snd_emu10k1
forcedeth              67340  0 
fuse                   66332  1 
hid                    53708  1 usbhid
i2c_core               41108  1 i2c_nforce2
i2c_nforce2            23296  0 
ieee1394              107016  1 ohci1394
ip6table_filter        19712  0 
ip6_tables             31376  1 ip6table_filter
iptable_filter         19840  0 
iptable_nat            23688  0 
ip_tables              30224  2 iptable_nat,iptable_filter
ipv6                  281064  12 
jbd                    73376  1 ext3
k8temp                 22016  0 
libata                176220  2 pata_amd,sata_nv
loop                   35332  0 
mbcache                25348  1 ext3
Module                  Size  Used by
ndiswrapper           214420  0 
nf_conntrack           79188  3 iptable_nat,nf_nat,nf_conntrack_ipv4
nf_conntrack_ipv4      27652  3 iptable_nat,nf_nat
nf_nat                 35736  1 iptable_nat
ohci1394               48432  0 
ohci_hcd               39940  0 
parport                52948  2 ppdev,parport_pc
parport_pc             55100  0 
pata_amd               30084  0 
powernow_k8            31748  0 
ppdev                  25348  0 
processor              67504  2 powernow_k8,thermal
rtc_cmos               27168  0 
rtc_core               37148  1 rtc_cmos
rtc_lib                19328  1 rtc_core
sata_nv                42764  3 
scsi_mod              168308  4 sr_mod,sg,sd_mod,libata
sd_mod                 45208  4 
sg                     52020  0 
snd                    79544  18 snd_pcm_oss,snd_mixer_oss,snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_util_mem,snd_hwdep
snd_ac97_codec        120868  1 snd_emu10k1
snd_emu10k1           162948  2 snd_emu10k1_synth
snd_emu10k1_synth      24832  0 
snd_emux_synth         54272  1 snd_emu10k1_synth
snd_hwdep              26372  2 snd_emux_synth,snd_emu10k1
snd_mixer_oss          33408  1 snd_pcm_oss
snd_page_alloc         27400  2 snd_emu10k1,snd_pcm
snd_pcm               100100  3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_pcm_oss            64256  0 
snd_rawmidi            42496  3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1
snd_seq                73664  5 snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_event,snd_seq_midi_emul
snd_seq_device         25100  6 snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq,snd_emu10k1,snd_rawmidi
snd_seq_midi           26112  0 
snd_seq_midi_emul      22784  1 snd_emux_synth
snd_seq_midi_event     23936  2 snd_seq_midi,snd_seq_virmidi
snd_seq_virmidi        23680  1 snd_emux_synth
snd_timer              40712  3 snd_seq,snd_emu10k1,snd_pcm
snd_util_mem           21632  2 snd_emux_synth,snd_emu10k1
soundcore              24264  1 snd
sr_mod                 33320  0 
thermal                39452  0 
usbcore               164684  5 usbhid,ndiswrapper,ehci_hcd,ohci_hcd
usbhid                 60260  0 
x_tables               33668  3 iptable_nat,ip_tables,ip6_tables
==================================================================================================
*** catMyConfig 
==================================================================================================
*** cat /etc/sysconfig/network/ifcfg-wlan0
BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR='192.168.178.20/24'
MTU=''
NAME='WLAN USB Device'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='hotplug'
USERCONTROL='no'
WIRELESS_AP=''
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_CA_CERT=''
WIRELESS_CHANNEL=''
WIRELESS_CLIENT_CERT=''
WIRELESS_CLIENT_KEY=''
WIRELESS_CLIENT_KEY_PASSWORD=''
WIRELESS_DEFAULT_KEY='0'
WIRELESS_EAP_AUTH=''
WIRELESS_EAP_MODE=''
WIRELESS_ESSID='Heimat'
WIRELESS_FREQUENCY=''
WIRELESS_KEY=''
WIRELESS_KEY_0=''
WIRELESS_KEY_1=''
WIRELESS_KEY_2=''
WIRELESS_KEY_3=''
WIRELESS_KEY_LENGTH='128'
WIRELESS_MODE='Managed'
WIRELESS_NICK=''
WIRELESS_NWID=''
WIRELESS_PEAP_VERSION=''
WIRELESS_POWER='yes'
WIRELESS_WPA_ANONID=''
WIRELESS_WPA_IDENTITY=''
WIRELESS_WPA_PASSWORD=''
WIRELESS_WPA_PSK='@@@@@@'
==================================================================================================
*** /usr/sbin/iwconfig | /usr/bin/sed "s/\(Encryption key:\)\([^o][^f][^f][^ ]*\)\(.*\)/\1@@ @@@-@@@@-@@@@-@@@@-@@@@-@@@@@@@\3/" 
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     Auto  Access Point: Not-Associated   Bit Rate:0 kb/s   
          Link Quality:100/100  Signal level:-65 dBm  Noise level:-96 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

==================================================================================================
*** /usr/bin/grep -i radio /var/log/boot.msg | /usr/bin/tail -n 5 
==================================================================================================
*** /usr/bin/grep -i firmware /var/log/messages* | /usr/bin/tail -n 5 
Jul 14 20:23:40 linux kernel: acx: firmware image 'tiacx111usbc1B' was not provided. Check your hotplug scripts
Jul 14 20:23:41 linux firmware.sh[5062]: Cannot find  firmware file 'tiacx111usbc1B'
Jul 14 20:31:16 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
Jul 15 19:16:07 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
Jul 16 18:53:57 linux kernel: acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
==================================================================================================
*** ls -ls /lib/firmware 
insgesamt 448
  4 -rw-r--r-- 1 root root  3408  6. Jun 22:18 aica_firmware.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 asihpi
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 digiface_firmware.bin
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 digiface_firmware_rev11.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 ea
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 emagic
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 emu
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 ess
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 korg
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 mixart
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 multiface_firmware.bin
100 -rw-r--r-- 1 root root 97652  6. Jun 22:18 multiface_firmware_rev11.bin
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 pcxhr
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 sb16
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 vx
  4 drwxr-xr-x 2 root root  4096 13. Jul 18:49 yamaha
==================================================================================================
*** ps aux | /usr/bin/grep wpa_supplicant | /usr/bin/grep -v grep 
root      2503  0.0  0.0   3856   880 ?        Ss   19:06   0:00 wpa_supplicant -iwlan0 -c/var/run/wpa_supplicant-wlan0.conf -Dwext -P/var/run/wpa_supplicant/wlan0.pid -B
==================================================================================================
*** /usr/bin/grep NETWORKMANAGER /etc/sysconfig/network/config | /usr/bin/grep -v "^#" 
NETWORKMANAGER=no
==================================================================================================
*** /usr/bin/grep -i persistent /etc/sysconfig/network/config | /usr/bin/grep -v "^#" | /usr/bin/grep -v "^$" 
==================================================================================================
*** /usr/bin/egrep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/70-persistent-net* | /usr/bin/grep -v ":#" | grep -v ":$" 
/usr/bin/egrep: /etc/udev/rules.d/*net_persistent*: Datei oder Verzeichnis nicht gefunden
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:04:0e:c8:4a:e5", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0f:ea:31:80:35", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
==================================================================================================
*** /usr/bin/egrep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*|/usr/bin/egrep -v '#|blacklist' 
/etc/modprobe.conf:install eth0             /bin/true
/etc/modprobe.conf:install eth1             /bin/true
==================================================================================================
*** detectFirmwareMessages 
No firmware messages found
==================================================================================================
*** detectAPs
 
OP
E

ExAzubi

Newbie
Noch ein kurzer Nachtrag,

also surfen kann ich ja die erste Zeit nach dem booten, wie schon mehrfach erwähnt. Dann nach gut 5 - 10 Min. kann ich nicht mehr surfen, auch beim pingen (egal ob lokal oder global) ist der "Host unreachable".

Ein iwlist wlan0 -scan klappt aber immer noch, d.h. er zeigt mir schön alle AP der Umgebung an!

Daraus schließe ich, das der Stick ansprechbar ist und auch läuft, denn wie kann er mir sosnt sagen welche AP in der nähe sind?

Für weitere Tipps bin ich wie gesagt dankbar.
 
Du bist am AP nicht angemeldet, das sagt uns iwconfig
Code:
wlan0     Auto  Access Point: Not-Associated   Bit Rate:0 kb/s   
          Link Quality:100/100  Signal level:-65 dBm  Noise level:-96 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
wer nicht am AP angemeldet ist bekommt auch keine IP Adresse zugewiesen. Du hast aber eine Adresse (das sagt ifconfig) und das verstehe ich nicht.
Code:
wlan0     Link encap:Ethernet  Hardware Adresse 00:04:0E:C8:4A:E5  
          inet Adresse:192.168.178.20  Bcast:192.168.178.255  Maske:255.255.255.0
          inet6 Adresse: fe80::204:eff:fec8:4ae5/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8639 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5298 errors:0 dropped:25 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:12198331 (11.6 Mb)  TX bytes:368031 (359.4 Kb)
Versuche nach dem die Verbindung gekappt wird neu sich anzumelden oder ziehe das USB WLAN-Stick raus und stecke es dann wieder rein.
Gruß
 
Zufällig habe ich in Dein ersten Script geschaut und das gefunden:
Code:
 wlan0     IEEE 802.11g  ESSID:"Heimat"  
          Mode:Managed  Frequency:2.437 GHz  Access Point: 00:1D:7E:18:E8:B7   
          Bit Rate=54 Mb/s   Tx-Power:10 dBm   Sensitivity=0/3  
          RTS thr:off   Fragment thr:off
          Encryption key:@@ @@@-@@@@-@@@@-@@@@-@@@@-@@@@@@@   Security mode:restricted
          Power Management:off
          Link Quality:46/100  Signal level:-66 dBm  Noise level:-96 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
Die Link Quality:46/100 << das ist sehr wenig, ein Wert um 55/100 wäre angebracht, deswegen flügst raus aus dem AP. Versuche AP näher zu gehen.
Gruß
 

ariel

Newbie
Hallo,
ich hatte anfänglich mit dem FritzStick ähnliche Probleme.
Ich hatte den Win.-Treiber mit Ndiswrapper erfolgreich installiert, die Benutzerdaten wie bekannt mit Yast.
mein FritzWLan funktionierte (Netzwerke in der Umgebung wurden angezeigt),
aber ich bekam keine Verbindung zur FritzBox?
Ich war schon kurz davor mir einen anderen Stick zu kaufen.
Durch zufall endeckte ich dann das Progamm "wpa_gui", womit mann, als Admin, ähnlich wie mit Yast seine Benutzerdaten eingeben kann.
Ebenfalls kann man nach Netzwerken in der Umgebung scannen und sich mit diesen Verbinden.

Seit dem funktioniert das WLan bei mir tadellos.
 

eldi2

Newbie
Hallo Ariel und alle,

bin neu in der Linux-Welt und habe beim Umstieg von Windoof aus Suse prompt kein Internet (Fritz-USB-Stick-Problematik, s.o.)

Durch zufall endeckte ich dann das Progamm "wpa_gui", womit mann, als Admin, ähnlich wie mit Yast seine Benutzerdaten eingeben kann.

Wo gibt's wpa_gui denn?

eldi2
 

SUSEDJAlex

Advanced Hacker
Hallo allerseits,
(die nachfolgende Schritte ohne den Stick durchführen!!!!!)
in YAST muss das Paket acx-kmp-flavour deinstalliert und auf "Tabu" gesetzt werden.
Danach in etc/modprobe.d/blacklist den Eintrag "blacklist acx" eintragen.
nun im YAST/Software installieren oder löschen die folgende Pakete installieren:
ndiswrapper, bind-chrootenv, kernel-source sowie ( wer es möchte ) kinternet

Nun mit ndiswrapper weitermachen:
Konsole öffnen:
su
(Rootpasswort)
ndiswrapper -i fwlan.inf ( bitte vorher ins Verzeichnis gehen, wo sich diese Datei befindet )
ndiswrapper -l
(ausgabe:) fwlan.inf hardware installed, present
echo ndiswrapper >> /etc/modules
modprobe ndiswrapper
ndiswrapper -m
( ausgabe:) ndiwrapper modules alias wlan0 added

konsole schließen mit exit

mit kate die etc/init.d/boot.local öffnen und den Eintrag (ganz am Ende) einfügen: modprobe ndiswrapper
speichern und schließen

REBOOT

nach dem Hochfahren dann den Stick einstecken
mit YAST konfigurieren:

Konfigurationsname: wlan0
Hardwarename: static-0
Modulname: ndiswrapper
Betriebsmodus: Verwaltet
Netzwerkname:Wie auch immer Ihr es genannt habt
Schlüssel-Eingabeart: Passphrase
Authenzifierungsmodus: WPA-PSK
Verschlüsslungs-Key: Steht hinten auf dem Router, oder ist von euch schon geändert worden

Und noch was: bitte den Namen euren Routers nicht verstecken.....sonst klappt das nicht....
nun mit kinternet oder networkmanager prüfen

Viel Spass !!!!

LG SUSE_DJAlex
 

ariel

Newbie
Hallo,
"wpa_supplicant-gui" heißt es genau.
Du findest es mit Yast - Software - Suchen - "wpa_supplicant-gui"
Aber wie gesagt vorher muß den Fritz usb Stick mit ndiswrapper laufen.
 
Oben