• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

WLan OpenSuse 10.3

Z

Zockerrufus

Newbie
Hallo!
Ich habe ein Problem mit meinem Wlan.habe einen usb-adapter gigaset 54 von siemens und eine eben eine netzwerkkarte
aber hier mal die auflistungen

Code: 
# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11g  ESSID:""
          Mode:Managed  Channel:0  Access Point: Not-Associated
          Retry min limit:7   RTS thr:off   Fragment thr=2346 B
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Code: 
ifconfig
eth0      Protokoll:Ethernet  Hardware Adresse 00:30:05:37:7B:C0
          inet Adresse:192.168.178.23  Bcast:192.168.178.255  Maske:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

lo        Protokoll:Lokale Schleife
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:14 errors:0 dropped:0 overruns:0 frame:0
          TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0
          RX bytes:700 (700.0 b)  TX bytes:700 (700.0 b)

Code: 
# lsusb
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 002: ID 083a:4521 Accton Technology Corp.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

Code: 
# lspci
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01)
00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AR [Radeon 9600]
01:00.1 Display controller: ATI Technologies Inc RV350 AR [Radeon 9600] (Secondary)
02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VM (LOM) Ethernet Controller (rev 81)

Code: 
# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11g  ESSID:""
          Mode:Managed  Channel:0  Access Point: Not-Associated
          Retry min limit:7   RTS thr:off   Fragment thr=2346 B
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Code: 
iwlist scanning
lo        Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning.

wlan0     Scan completed :
          Cell 01 - Address: 00:04:0E:45:E4:E7
                    ESSID:"FRITZ!Box Fon WLAN"
                    Mode:Master
                    Channel:6
                    Frequency:2.437 GHz
                    Signal level=49/100
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s
                              6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s
                              36 Mb/s; 48 Mb/s; 54 Mb/s
                    Extra:tsf=000000a02df9b19f

Code: 
wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant.conf -B -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
eapol_version=1
ap_scan=1
Line: 13 - start of a new network block
ssid - hexdump_ascii(len=18):
     46 52 49 54 5a 21 42 6f 78 20 46 6f 6e 20 57 4c   FRITZ!Box Fon WL
     41 4e                                             AN
scan_ssid=1 (0x1)
proto: 0x1
key_mgmt: 0x2
pairwise: 0x10
group: 0x8
PSK - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='FRITZ!Box Fon WLAN'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:30:f1:e9:63:b1
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - wpa_driver_wext_set_drop_unencrypted
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x1 - Setting scan request: 0 sec 100000 usec
Added interface wlan0
Daemonize..



allerdings finder er nix bei dhclient wlan0

Code: 
dhclient wlan0
Internet Systems Consortium DHCP Client V3.0.6
Copyright 2004-2007 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

wmaster0: unknown hardware address type 801
wmaster0: unknown hardware address type 801
Listening on LPF/wlan0/00:30:f1:e9:63:b1
Sending on   LPF/wlan0/00:30:f1:e9:63:b1
Sending on   Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6
No DHCPOFFERS received.
No working leases in persistent database - sleeping.

bei yast erkennt er zwar meine netzwerkkarte, steht aber im klammern dass sie nicht angeschlossen ist und meinen usb-adapter erkennt yast gar nicht

kann mir hier vielleicht jemand helfen?
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben