faulaenzer
Newbie
Hallo. Leider bekomme ich meine D-Link DWL G520+ Wireless-Lan Karte unter openSUSE 10.2 nicht zum laufen. Die Karte läuft unter WindowsXP und lief unter Ubuntu einwandfrei. Mit der neuen Ubuntu läuft auch nichts mehr!
Mittlerweile habe ich die Firmware installiert, es tut sich aber dennoch nichts. Mein WLAN Netzwerk wird erkannt, aber eine Verbindung wird nicht aufgebaut. Im Router habe ich alle Funktionen wie Verschlüsselung und Mac-Adressen-Filterung deaktiviert.
Wäre euch echt dankbar wenn wir mein SUSE zum laufen kriegen würden.
Hier mal ein paar Infos:
Mittlerweile habe ich die Firmware installiert, es tut sich aber dennoch nichts. Mein WLAN Netzwerk wird erkannt, aber eine Verbindung wird nicht aufgebaut. Im Router habe ich alle Funktionen wie Verschlüsselung und Mac-Adressen-Filterung deaktiviert.
Wäre euch echt dankbar wenn wir mein SUSE zum laufen kriegen würden.
Hier mal ein paar Infos:
Code:
linuxbox:/home/alex # lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP]
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
00:05.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 03)
00:09.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
00:0a.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless Interface
00:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
00:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti 4200 AGP 8x] (rev a1)
Code:
linuxbox:/home/alex # iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11b+/g+ ESSID:"" Nickname:"acx v0.3.35"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power=15 dBm Sensitivity=1/3
Retry min limit:7 RTS thr:off
Encryption key:off
Power Management:off
Link Quality=39/100 Signal level=14/100 Noise level=0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Code:
linuxbox:/home/alex # ifconfig
lo Protokoll:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:409 errors:0 dropped:0 overruns:0 frame:0
TX packets:409 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 Sendewarteschlangenlänge:0
RX bytes:35224 (34.3 Kb) TX bytes:35224 (34.3 Kb)
wlan0 Protokoll:Ethernet Hardware Adresse 00:80:C8:2C:1A:68
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11
Code:
linuxbox:/home/alex # lsmod | grep acx
acx 145032 0
firmware_class 14080 1 acx
usbcore 114896 6 usb_storage,usblp,usbhid,acx,ehci_hcd,uhci_hcd
Code:
linuxbox:/home/alex # rpm -qa | grep -r wlan
wlan-kmp-default-1_2.6.18.2_34-16
Code:
linuxbox:/home/alex # ls -ls /lib/firmware
insgesamt 832
80 -rw-r--r-- 1 root root 76802 29. Nov 14:51 ql2100_fw.bin
88 -rw-r--r-- 1 root root 84566 29. Nov 14:51 ql2200_fw.bin
124 -rw-r--r-- 1 root root 121872 29. Nov 14:51 ql2300_fw.bin
136 -rw-r--r-- 1 root root 131464 29. Nov 14:51 ql2322_fw.bin
200 -rw-r--r-- 1 root root 196900 29. Nov 14:51 ql2400_fw.bin
116 -rw-r--r-- 1 root root 112494 29. Nov 14:51 ql6312_fw.bin
88 -rwxr-xr-x 1 root root 83320 23. Jan 17:38 tiacx111c16
Code:
linuxbox:/home/alex # ls -R /lib/modules/ | grep -r acx
acx.ko
Code:
linuxbox:/home/alex # cat /etc/resolv.conf
nameserver 192.168.0.1
search homenet
Code:
linuxbox:/home/alex # cat /etc/sysconfig/network/routes
default 192.168.0.1 - -
Code:
linuxbox:/home/alex # ls /etc/sysconfig/network/
config ifcfg-lo ifcfg-wlan-bus-pci-0000:00:0a.0 ifroute-lo providers routes.YaST2save
dhcp ifcfg.template if-down.d if-up.d routes scripts
Code:
linuxbox:/etc/sysconfig/network # cat ifcfg-wlan-bus-pci-0000:00:0a.0
BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR='192.168.0.3'
MTU=''
NAME='D-Link DWL-G520+ Wireless PCI Adapter'
NETMASK='255.255.255.0'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='auto'
UNIQUE='bSAa.kz3r2x6bnPF'
USERCONTROL='yes'
WIRELESS_AP=''
WIRELESS_AUTH_MODE='open'
WIRELESS_BITRATE='auto'
WIRELESS_CA_CERT=''
WIRELESS_CHANNEL=''
WIRELESS_CLIENT_CERT=''
WIRELESS_CLIENT_KEY=''
WIRELESS_CLIENT_KEY_PASSWORD=''
WIRELESS_DEFAULT_KEY='0'
WIRELESS_EAP_AUTH=''
WIRELESS_EAP_MODE=''
WIRELESS_ESSID='WLAN4US'
WIRELESS_FREQUENCY=''
WIRELESS_KEY=''
WIRELESS_KEY_0=''
WIRELESS_KEY_1=''
WIRELESS_KEY_2=''
WIRELESS_KEY_3=''
WIRELESS_KEY_LENGTH='128'
WIRELESS_MODE='Managed'
WIRELESS_NICK=''
WIRELESS_NWID=''
WIRELESS_PEAP_VERSION=''
WIRELESS_POWER='yes'
WIRELESS_WPA_ANONID=''
WIRELESS_WPA_IDENTITY=''
WIRELESS_WPA_PASSWORD=''
WIRELESS_WPA_PSK=''
_nm_name='bus-pci-0000:00:0a.0'
Code:
alex@linuxbox:~> dmesg
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (1 sec)
get_mask 0x00000000, set_mask 0x00000040
setting RXconfig to 2010:0FDD
get_mask 0x00000000, set_mask 0x00000000 - after update
start_scan: seems like previous scan is still running. Not starting anew. Please report
scan table: SSID='WLAN4US' CH=6 SIR=14 SNR=0
peer_cap 0x0001, needed_cap 0x0001
ESSID doesn't match! ('WLAN4US' station, '' config)
no matching station found in range yet
acx_set_status(1):SCANNING
starting radio scan
.
.
.
Code:
alex@linuxbox:~> ls -ls /etc/sysconfig/network/ifcfg-wlan*
4 -rw-r--r-- 1 root root 878 23. Jan 17:51 /etc/sysconfig/network/ifcfg-wlan-bus-pci-0000:00:0a.0