lomo2003
Member
Hallo und gute Tag,
ich habe folgendes Problem!!!
Wenn ich SuSe 10.2 x86_64 starte funzt die Wirelesskarte nicht.
aber wenn ich zuvor SuSE 10.1 gestartet habe und dann danach ein reboot mache und SuSe 10.2 x86_64 starte wird die Karte eingerichtet und funktioniert!!!!
HHmm????
Unter SUSE 10.1 wird die Karte mit Ndiswrapper eingebunden.
Unter SuSe 10.2 x86_64 habe ich die Katen mittels Kernelmodul "bcm43xx" eingebunden.
dmesg sagt mir, wenn die Karten nicht funzt:
und nach dem reboot von 10.1 zu 10.2 :
Wie kann ich dies lösen das die Karte direkt nach dem Einschalten funktioniert!!!
THX im voraus ToM.
ich habe folgendes Problem!!!
Wenn ich SuSe 10.2 x86_64 starte funzt die Wirelesskarte nicht.
aber wenn ich zuvor SuSE 10.1 gestartet habe und dann danach ein reboot mache und SuSe 10.2 x86_64 starte wird die Karte eingerichtet und funktioniert!!!!
HHmm????
Unter SUSE 10.1 wird die Karte mit Ndiswrapper eingebunden.
Unter SuSe 10.2 x86_64 habe ich die Katen mittels Kernelmodul "bcm43xx" eingebunden.
dmesg sagt mir, wenn die Karten nicht funzt:
Code:
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
ieee80211_crypt: registered algorithm 'WEP'
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
Losing some ticks... checking if CPU frequency changed.
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
audit(1168027069.684:3): audit_backlog_limit=256 old=64 by auid=4294967295
audit(1168027069.776:4): audit_pid=3715 old=0 by auid=4294967295
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Initialized drm 1.0.1 20051102
GSI 23 sharing vector 0x42 and IRQ 23
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 66
[drm] Initialized radeon 1.25.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
ieee80211_crypt: registered algorithm 'TKIP'
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
ieee80211_crypt: registered algorithm 'CCMP'
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
und nach dem reboot von 10.1 zu 10.2 :
Code:
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
ieee80211_crypt: registered algorithm 'WEP'
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1, .auth_mode = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Already requested authentication, waiting...
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
SoftMAC: Open Authentication completed with 00:40:05:5e:2a:ca
SoftMAC: sent association request!
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Authentication response received from 00:40:05:5e:2a:ca but no queue item exists.
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
Losing some ticks... checking if CPU frequency changed.
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
SoftMAC: Open Authentication completed with 00:40:05:5e:2a:ca
SoftMAC: sent association request!
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
SoftMAC: sent association request!
audit(1168027950.566:3): audit_pid=3721 old=0 by auid=4294967295
SoftMAC: assoc request timed out!
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Initialized drm 1.0.1 20051102
GSI 23 sharing vector 0x42 and IRQ 23
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 66
[drm] Initialized radeon 1.25.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:01:00:04:0e:a9:14:27:08:00 SRC=192.168.0.254 DST=224.0.0.1 LEN=36 TOS=0x00 PREC=0xC0 TTL=1 ID=46850 DF OPT (94040000) PROTO=2
psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.
ieee80211_crypt: registered algorithm 'TKIP'
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
ieee80211_crypt: registered algorithm 'CCMP'
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 2, .enabled = 1, .encrypt = 1
bcm43xx: set security called, .level = 4, .enabled = 1, .encrypt = 1
r8169: eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth0: link is not ready
SoftMAC: Canceling existing associate request!
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
NET: Registered protocol family 17
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
bcm43xx: set security called, .active_key = 0, .enabled = 1, .encrypt = 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Queueing Authentication Request to 00:40:05:5e:2a:ca
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .active_key = 0, .enabled = 1, .encrypt = 1
SoftMAC: Already associating or associated to 00:40:05:5e:2a:ca
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
bcm43xx: set security called, .active_key = 0, .enabled = 1, .encrypt = 1
SoftMAC: Already associating or associated to 00:40:05:5e:2a:ca
SoftMAC: Sent Authentication Request to 00:40:05:5e:2a:ca.
printk: 9 messages suppressed.
SoftMAC: Open Authentication completed with 00:40:05:5e:2a:ca
SoftMAC: sent association request!
SoftMAC: associated!
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
eth0: no IPv6 routers present
SoftMAC: Scanning finished
Wie kann ich dies lösen das die Karte direkt nach dem Einschalten funktioniert!!!
THX im voraus ToM.