Dell 1450 Wireless USB Adapter

Hallo Ihr,

ich komm mit der Installation meines Dell Adapters einfach nicht weiter.

Hier die Fakten:
Suse 10.0 32bit
Ndiswrapper 1.23
32bit Treiber von Original CD
Das modul ndsiwrapper ist geladen, Treiber installiert, keine Fehlermeldungen, aber das Gerät wird nicht angesprochen.

Aufgefallen ist mir:
In der Anleitung von Opensuse steht beim Laden des Treibers
ndiswrapper adding xxx.sys laut dmesg, dies geschieht bei mir nicht.

Hat jemand ne Idee wo ich ansetzen könnte?

Vielen Dank und Gruss
Alex

Wenn du hier Hilfe erwartest, solltest du zuerst detailliert posten, was du genau gemacht hast mit welchem Ergebnis.

Hallo,

ich hab nach der Anleitung auf dieser Seite http://nextgen.no-ip.org/~andrew/linux/ndiswrapper/ndiswrapperinfo10-32bit.php
versucht meinen Dell Wireless Adapter zu installieren und wie oben beschrieben funzt der leider nicht...

Wie ich oben bereits erwähnte, erwarte ich hier mehr Details, insbesondere fehlen deinem Posting sämtliche Ausgaben des Systems. Die Arbeit wirst du also wohl machen müssen.

Hier die Ausgabe von dmesg:

Linux version 2.6.13-15.12-smp (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 SMP Thu Aug 24 11:23:58 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f686c00 (usable)
BIOS-e820: 000000003f686c00 - 000000003f688c00 (ACPI NVS)
BIOS-e820: 000000003f688c00 - 000000003f68ac00 (ACPI data)
BIOS-e820: 000000003f68ac00 - 0000000040000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
118MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
On node 0 totalpages: 259718
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 30342 pages, LIFO batch:15
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v002 DELL ) @ 0x000feb00
ACPI: XSDT (v001 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd24f
ACPI: FADT (v003 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd347
ACPI: SSDT (v001 DELL st_ex 0x00001000 INTL 0x20050309) @ 0xfffd717c
ACPI: MADT (v001 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd43b
ACPI: BOOT (v001 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd4ad
ACPI: ASF! (v016 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd4d5
ACPI: MCFG (v001 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd53c
ACPI: HPET (v001 DELL GX520 0x00000007 ASL 0x00000061) @ 0x000fd57a
ACPI: DSDT (v001 DELL dt_ex 0x00001000 INTL 0x20050309) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:b0000000)
Built 1 zonelists
Kernel command line: root=/dev/sda6 vga=0x31a selinux=0 resume=/dev/sda5 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2793.685 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1022280k/1038872k available (2331k kernel code, 15600k reserved, 748k data, 252k init, 121368k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5593.69 BogoMIPS (lpj=11187385)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000080 0000641d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1794k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
CPU0: Intel(R) Pentium(R) D CPU 2.80GHz stepping 07
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.85 BogoMIPS (lpj=11173711)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000001
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000080 0000641d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 07
Total of 2 processors activated (11180.54 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb894, last bus=4
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:00: ioport range 0x800-0x85f could not be reserved
pnp: 00:00: ioport range 0xc00-0xc7f has been reserved
pnp: 00:00: ioport range 0x860-0x8ff has been reserved
pnp: 00:08: ioport range 0x100-0x1fe has been reserved
pnp: 00:08: ioport range 0x200-0x277 has been reserved
pnp: 00:08: ioport range 0x280-0x2e7 has been reserved
pnp: 00:08: ioport range 0x2f0-0x2f7 has been reserved
pnp: 00:08: ioport range 0x300-0x377 has been reserved
pnp: 00:08: ioport range 0x380-0x3bb has been reserved
pnp: 00:08: ioport range 0x3c0-0x3e7 has been reserved
pnp: 00:08: ioport range 0x3f6-0x3f7 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fe900000-fe9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: fe800000-fe8fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: fe700000-fe7fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:1c.1 -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
Simple Boot Flag at 0x7a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1159452435.392:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.1 -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 7872k, total 7872k
vesafb: mode is 1280x1024x16, linelength=2560, pages=2
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 112645 bytes,<6>...found (1280x1024, 17839 bytes, v3).
Console: switching to colour frame buffer device 158x59
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI wakeup devices:
VBTN PCI0 PCI4 PCI2 PCI3 PCI1 PCI5 PCI6 USB0 USB1 USB2 USB3
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 252k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdaMA, hdbio
Probing IDE interface ide0...
hda: PHILIPS DVD+/-RW DVD8801, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
libata version 1.12 loaded.
ata_piix version 1.04
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 217
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 217
ata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4023 85:7469 86:3e41 87:4023 88:207f
ata1: dev 0 ATA, max UDMA/133, 312500000 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ATA: abnormal status 0xFF on port 0xFE27
ata2: disabling port
scsi1 : ata_piix
Vendor: ATA Model: WDC WD1600JS-75N Rev: 10.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
ACPI: CPU0 (power states: C1[C1])
ACPI: CPU1 (power states: C1[C1])
ACPI-0748: *** Warning: Processor Device is not present
ACPI-0521: *** Warning: Error getting cpuindex for acpiid 0x3
ACPI-0748: *** Warning: Processor Device is not present
ACPI-0521: *** Warning: Error getting cpuindex for acpiid 0x4
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: sda6: found reiserfs format "3.6" with standard journal
ReiserFS: sda6: using ordered data mode
ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda6: checking transaction log (sda6)
ReiserFS: sda6: Using r5 hash to sort names
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 1052216k swap on /dev/sda5. Priority:-1 extents:1
bootsplash: status on console 0 changed to on
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NTFS driver 2.1.23 [Flags: R/W MODULE].
NTFS volume version 3.1.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ndiswrapper: module not supported by Novell, setting U taint flag.
ndiswrapper version 1.23 loaded (preempt=no,smp=yes)
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
lp0: using parport0 (interrupt-driven).
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 225, io base 0x0000ff80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 22 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 233, io base 0x0000ff60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 50, io base 0x0000ff40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 58, io base 0x0000ff20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xe0000000
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
hw_random hardware driver 1.0.0 loaded
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 225, io mem 0xffa80800
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
tg3.c:v3.37 (August 25, 2005)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Tigon3 [partno(BCM5751PKFBG) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:18:8b:09:ad:31
eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000]
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 23 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 54304 usecs
intel8x0: clocking to 48000
usb 5-3: new high speed USB device using ehci_hcd and address 3
hub 5-3:1.0: USB hub found
hub 5-3:1.0: 4 ports detected
usb 5-6: new high speed USB device using ehci_hcd and address 4
usb 1-2: new low speed USB device using uhci_hcd and address 3
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
bootsplash: status on console 0 changed to on
usb 5-3.3: new full speed USB device using ehci_hcd and address 5
hub 5-3.3:1.0: USB hub found
hub 5-3.3:1.0: 4 ports detected
usb 5-3.3.2: new full speed USB device using ehci_hcd and address 6
usb 5-3.3.2: not running at top speed; connect to a high speed hub
usb 5-3.3.2: 400mA over 100mA budget!
hub 5-3.3:1.0: 100mA over power budget!
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-2
input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
NET: Registered protocol family 17
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Vendor: WD Model: 3200JB External Rev: 1.07
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: assuming drive cache: write through
sdb: sdb1 sdb2 < sdb5 sdb6 >
Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
mtrr: 0xe0000000,0x10000000 overlaps existing 0xe0000000,0x400000
bootsplash: status on console 0 changed to on
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [VBTN]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03bb0a0(lo)
IPv6 over IPv4 tunneling driver
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: No new microcode data for CPU0
microcode: No new microcode data for CPU1
IA-32 Microcode Update Driver v1.14 unregistered
powernow: This module only works with AMD K7 CPUs
bootsplash: status on console 0 changed to on
subfs 0.9
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
eth0: no IPv6 routers present
ip_tables: (C) 2000-2002 Netfilter core team
eth0: no IPv6 routers present
usb 5-3.3.2: USB disconnect, address 6
usb 5-3.4: new high speed USB device using ehci_hcd and address 7
usb 5-3.3: USB disconnect, address 5
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
usb 5-3.4: USB disconnect, address 7
tg3: eth0: Link is down.
usb 5-4: new high speed USB device using ehci_hcd and address 8
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
FIFO write timed out
usb 5-3.2: new full speed USB device using ehci_hcd and address 9
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 9 if 0 alt 0 proto 2 vid 0x04A9 pid 0x1094
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
parport0: FIFO is stuck
parport0: BUSY timeout (1) in compat_write_block_pio
FIFO write timed out
parport0: FIFO is stuck
parport0: BUSY timeout (1) in compat_write_block_pio
FIFO write timed out
usb 5-3.2: USB disconnect, address 9
drivers/usb/class/usblp.c: usblp0: removed

die iwconfig sieht so aus:

lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

lsmod:

Module Size Used by
usblp 17024 0
iptable_filter 6912 0
ip_tables 25344 1 iptable_filter
joydev 13760 0
nls_iso8859_1 8064 1
nls_cp437 9728 1
subfs 12672 4
speedstep_lib 8452 0
freq_table 8832 0
snd_pcm_oss 67616 0
snd_mixer_oss 24704 1 snd_pcm_oss
snd_seq 62864 0
ipv6 280192 14
snd_seq_device 13068 1 snd_seq
button 11024 0
battery 14212 0
ac 9220 0
edd 14560 0
af_packet 31368 2
usbhid 50656 0
usb_storage 81600 1
snd_intel8x0 39136 3
i2c_i801 12812 0
i2c_core 25344 1 i2c_i801
snd_ac97_codec 98428 1 snd_intel8x0
tg3 105860 0
generic 8452 0 [permanent]
snd_ac97_bus 6400 1 snd_ac97_codec
ehci_hcd 38920 0
hw_random 9492 0
snd_pcm 109700 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 31108 2 snd_seq,snd_pcm
snd 71300 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 13920 1 snd
snd_page_alloc 15112 2 snd_intel8x0,snd_pcm
intel_agp 26652 1
agpgart 38476 2 intel_agp
uhci_hcd 39440 0
pci_hotplug 32188 0
parport_pc 45252 1
lp 15780 2
parport 40392 2 parport_pc,lp
ndiswrapper 203632 0
usbcore 126720 7 usblp,usbhid,usb_storage,ehci_hcd,uhci_hcd,ndiswrapper
nls_utf8 6016 1
ntfs 202896 1
vfat 18048 1
fat 56348 1 vfat
dm_mod 63004 0
reiserfs 269424 1
fan 8964 0
thermal 18696 0
sg 42528 0
processor 32104 1 thermal
ata_piix 13956 3
ide_cd 46084 0
cdrom 42912 1 ide_cd
libata 55428 1 ata_piix
piix 14596 0 [permanent]
sd_mod 23808 6
scsi_mod 142952 4 usb_storage,sg,libata,sd_mod
ide_disk 22656 0
ide_core 136528 5 usb_storage,generic,ide_cd,piix,ide_disk

Und auf ndiswrapper -l sagt mein PC das:

Installed drivers:
dellnic driver installed, hardware present

Brauchst du noch andere Infos?

Vielen Dank und Gruss

Schau einmal, ob du mit dem Treiber von hier weiterkommst. Ansonsten such einmal nach Broadcom Chipsatz hier.