Habe in mein älteres Toshiba Tecra (SuSE 10.1) zusätzlich zur eingebauten WLAN Karte von Toshiba (Lucent) mir eine Prism Intersil zugelegt, da die alte Karte kein WPA kann und nur WLAN b. Ich dachte SuSe untestützt die Prism.
Im Yast wird die Karte erkannt und kann konfiguriert werden. Die Toshiba Karte Habe ich deaktiviert.
Im KNetworkmanager wird die Karte auch angezeit, aber ein Verbindungsaufbau geht nicht. Wenn ich auf aktivieren gehe klappt es nicht. Es scheint, als sei die Karte nicht aktiviert.
Folgendes wird im Startmenü angezeigt: (Sieht irgendwie nach einem Problem aus.
Danke im Voraus
Doc
<7>orinoco 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
<7>eth1: resetting device...
<7>eth1: uploading firmware...
<7>orinoco_cs 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
<3>prism54: request_firmware() failed for 'isl3890'
<3>eth1: could not upload firmware ('isl3890')
<3>eth1: islpci_reset: failure
<7>eth2: Hardware identity 0005:0002:0001:0002
<7>eth2: Station identity 001f:0001:0006:000e
<7>eth2: Firmware determined as Lucent/Agere 6.14
<7>eth2: Ad-hoc demo mode supported
<7>eth2: IEEE standard IBSS ad-hoc mode supported
<7>eth2: WEP supported, 104-bit key
<7>eth2: MAC address 00:02:2D:24:CE:55
<7>eth2: Station name "HERMES I"
<7>eth2: ready
<7>eth2: index 0x01: Vcc 3.3, irq 11, io 0xd100-0xd13f
<6>hw_random hardware driver 1.0.0 loaded
<6>eth2 renamed to ethxx2
<7>eth1: resetting device...
<7>eth1: uploading firmware...
<3>prism54: request_firmware() failed for 'isl3890'
<3>eth1: could not upload firmware ('isl3890')
<3>eth1: islpci_reset: failure
<6>ethxx2 renamed to eth2
Im Yast wird die Karte erkannt und kann konfiguriert werden. Die Toshiba Karte Habe ich deaktiviert.
Im KNetworkmanager wird die Karte auch angezeit, aber ein Verbindungsaufbau geht nicht. Wenn ich auf aktivieren gehe klappt es nicht. Es scheint, als sei die Karte nicht aktiviert.
Folgendes wird im Startmenü angezeigt: (Sieht irgendwie nach einem Problem aus.
Danke im Voraus
Doc
<7>orinoco 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
<7>eth1: resetting device...
<7>eth1: uploading firmware...
<7>orinoco_cs 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
<3>prism54: request_firmware() failed for 'isl3890'
<3>eth1: could not upload firmware ('isl3890')
<3>eth1: islpci_reset: failure
<7>eth2: Hardware identity 0005:0002:0001:0002
<7>eth2: Station identity 001f:0001:0006:000e
<7>eth2: Firmware determined as Lucent/Agere 6.14
<7>eth2: Ad-hoc demo mode supported
<7>eth2: IEEE standard IBSS ad-hoc mode supported
<7>eth2: WEP supported, 104-bit key
<7>eth2: MAC address 00:02:2D:24:CE:55
<7>eth2: Station name "HERMES I"
<7>eth2: ready
<7>eth2: index 0x01: Vcc 3.3, irq 11, io 0xd100-0xd13f
<6>hw_random hardware driver 1.0.0 loaded
<6>eth2 renamed to ethxx2
<7>eth1: resetting device...
<7>eth1: uploading firmware...
<3>prism54: request_firmware() failed for 'isl3890'
<3>eth1: could not upload firmware ('isl3890')
<3>eth1: islpci_reset: failure
<6>ethxx2 renamed to eth2