Wlan an ---->absturz

hallo


das problem ist folgendes

wenn ich die Wlankarte aktiviere sei es über System Start oder über modprobe friert das System ein

die Karte kriegt noch eine ip über DHcP und ende

für mich schauts so aus wie wenn sich da irdwas nicht verträgt

mein system

Dlink DWL G520+ mit treiber ACX111 über Yast installiert

SUSE 10.0 neu aufgesetzt und über Yast geupdatet


amd 64 3000+

asus main

nvidia 6600 gt

Logs kommen gleich

hoffe ihr habt rad

das letzte boot.osm

Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8
done eth1 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
eth1 configuration: eth-id-00:0e:2e:36:5a:d0
eth1 is controlled by ifplugd
done wlan0 device: Texas Instruments ACX 111 54Mbps Wireless Interface
wlan0 configuration: wlan-id-00:13:46:b0:53:2b
wlan0 Startmode is 'manual'
skippedSetting up service network . . . . . . . . . . . . . . . .done

das log ist von einen start mit wlan sofort an

etting up network interfaces:
lo
lo IP address: 127.0.0.1/8
done eth0 device: nVidia Corporation CK804 Ethernet Controller (rev a3)
eth0 No configuration found for eth0
unused eth1 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
eth1 configuration: eth-id-00:0e:2e:36:5a:d0
eth1 (DHCP) . . . . . no IP address yet... backgrounding.
waiting
wlan0 device: Texas Instruments ACX 111 54Mbps Wireless Interface
wlan0 configuration: wlan-id-00:13:46:b0:53:2b
wlan0 warning: using NO encryption
wlan0 IP address: 192.168.178.25/24
doneWaiting for mandatory devices: eth-id-00:0e:2e:36:5a:d0 __NSC__
12 10 9 8 <notice>checkproc: /opt/kde3/bin/kdm 5281



iwconfig




lo no wireless extensions.

sit0 no wireless extensions.

wlan0 IEEE 802.11b+/g+ ESSID:"STAB0532B" Nickname:"8"
Mode:Auto Channel:1 Bit Rate=54 Mb/s Tx-Power=15 dBm
Sensitivity=1981820976/3
Retry min limit:7 RTS thrff
Encryption keyff
Power Managementff
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

eth1 no wireless extensions.



es ist genau so das wenn ich das Wlan aktivire egal wie also Router einstecken,oder modprobe, Router (Fritzbox 7050 ) Wlan aktiviern oder sonst irgenwie das System sofort einfriert keine Reaktion auf irgenwas auser Reset

Was steht nach einem solchen Absturz als letztes in der /var/log/messages?

l 2 12:45:31 linux syslog-ng[4642]: syslog-ng version 1.6.8 starting
Jul 2 12:45:31 linux ifplugd(eth1)[4881]: ifplugd 0.27 initializing.
Jul 2 12:45:31 linux ifplugd(eth1)[4881]: Using interface eth1/00:0E:2E:36:5A0 with driver <8139too> (version: 0.9.27)
Jul 2 12:45:31 linux ifplugd(eth1)[4881]: Using detection mode: SIOCETHTOOL
Jul 2 12:45:31 linux ifplugd(eth1)[4881]: Initialization complete, link beat not detected.
Jul 2 12:45:33 linux syslog-ng[4642]: Changing permissions on special file /dev/xconsole
Jul 2 12:45:33 linux syslog-ng[4642]: Changing permissions on special file /dev/tty10
Jul 2 12:45:33 linux ifup: No configuration found for sit0
Jul 2 12:45:36 linux kernel: klogd 1.4.1, log source = /proc/kmsg started.
Jul 2 12:45:36 linux kernel: parport0: PC-style at 0x378 (0x778)<6>NET: Registered protocol family 10
Jul 2 12:45:36 linux kernel: Disabled Privacy Extensions on device ffffffff803cf680(lo)
Jul 2 12:45:36 linux kernel: IPv6 over IPv4 tunneling driver
Jul 2 12:45:36 linux kernel: [PCSPP,TRISTATE]
Jul 2 12:45:36 linux kernel: parport0: irq 7 detected
Jul 2 12:45:36 linux kernel: lp0: using parport0 (polling).
Jul 2 12:45:36 linux kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Jul 2 12:45:36 linux kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Jul 2 12:45:36 linux kernel: usbcore: registered new driver usbfs
Jul 2 12:45:36 linux kernel: usbcore: registered new driver hub
Jul 2 12:45:36 linux kernel: ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Jul 2 12:45:36 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 217
Jul 2 12:45:36 linux kernel: PCI: Setting latency timer of device 0000:00:02.0 to 64
Jul 2 12:45:36 linux kernel: ohci_hcd 0000:00:02.0: OHCI Host Controller
Jul 2 12:45:36 linux kernel: ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
Jul 2 12:45:36 linux kernel: ohci_hcd 0000:00:02.0: irq 217, io mem 0xd0101000
Jul 2 12:45:36 linux kernel: hub 1-0:1.0: USB hub found
Jul 2 12:45:36 linux kernel: hub 1-0:1.0: 10 ports detected
Jul 2 12:45:36 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCL] -> GSI 22 (level, low) -> IRQ 225
Jul 2 12:45:36 linux kernel: PCI: Setting latency timer of device 0000:00:02.1 to 64
Jul 2 12:45:36 linux kernel: ehci_hcd 0000:00:02.1: EHCI Host Controller
Jul 2 12:45:36 linux kernel: ehci_hcd 0000:00:02.1: debug port 1
Jul 2 12:45:36 linux kernel: ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
Jul 2 12:45:36 linux kernel: ehci_hcd 0000:00:02.1: irq 225, io mem 0xfeb00000
Jul 2 12:45:36 linux kernel: PCI: cache line size of 64 is not supported by device 0000:00:02.1
Jul 2 12:45:36 linux kernel: ehci_hcd 0000:00:02.1: park 0
Jul 2 12:45:36 linux kernel: ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
Jul 2 12:45:36 linux kernel: hub 2-0:1.0: USB hub found
Jul 2 12:45:36 linux kernel: hub 2-0:1.0: 10 ports detected
Jul 2 12:45:36 linux kernel: SCSI subsystem initialized
Jul 2 12:45:36 linux kernel: libata version 1.12 loaded.
Jul 2 12:45:36 linux kernel: ACPI-0212: *** Warning: Device is not power manageable
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 21 (level, low) -> IRQ 233
Jul 2 12:45:36 linux kernel: PCI: Setting latency timer of device 0000:00:04.0 to 64
Jul 2 12:45:36 linux kernel: intel8x0_measure_ac97_clock: measured 54719 usecs
Jul 2 12:45:36 linux kernel: intel8x0: clocking to 46902
Jul 2 12:45:36 linux kernel: acx_pci: module not supported by Novell, setting U taint flag.
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt 0000:05:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 50
Jul 2 12:45:36 linux kernel: usb 2-6: new high speed USB device using ehci_hcd and address 3
Jul 2 12:45:36 linux kernel: 8139too Fast Ethernet driver 0.9.27
Jul 2 12:45:36 linux kernel: i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
Jul 2 12:45:36 linux kernel: i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
Jul 2 12:45:36 linux kernel: usb 1-5: new full speed USB device using ohci_hcd and address 2
Jul 2 12:45:36 linux kernel: Floppy drive(s): fd0 is 1.44M
Jul 2 12:45:36 linux kernel: FDC 0 is a post-1991 82077
Jul 2 12:45:36 linux kernel: drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
Jul 2 12:45:36 linux kernel: usbcore: registered new driver usblp
Jul 2 12:45:36 linux kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Jul 2 12:45:36 linux kernel: Initializing USB Mass Storage driver...
Jul 2 12:45:36 linux kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jul 2 12:45:36 linux kernel: usb-storage: device found at 3
Jul 2 12:45:36 linux kernel: usb-storage: waiting for device to settle before scanning
Jul 2 12:45:36 linux kernel: usbcore: registered new driver usb-storage
Jul 2 12:45:36 linux kernel: USB Mass Storage support registered.
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
Jul 2 12:45:36 linux kernel: ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 58
Jul 2 12:45:36 linux kernel: eth0: RealTek RTL8139 at 0xffffc2000002e000, 00:0e:2e:36:5a:d0, IRQ 58
Jul 2 12:45:36 linux kernel: eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Jul 2 12:45:36 linux kernel: Adding 1052216k swap on /dev/hdb1. Priority:-1 extents:1
Jul 2 12:45:36 linux kernel: eth1: link down
Jul 2 12:45:36 linux kernel: BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Jul 2 12:45:36 linux kernel: NET: Registered protocol family 17
Jul 2 12:45:36 linux kernel: Vendor: ICSI Model: IC1210 CF Rev: 1.6F
Jul 2 12:45:36 linux kernel: Type: Direct-Access ANSI SCSI revision: 00
Jul 2 12:45:36 linux kernel: Vendor: ICSI Model: IC1210 MS Rev: 1.6F
Jul 2 12:45:36 linux kernel: Type: Direct-Access ANSI SCSI revision: 00
Jul 2 12:45:36 linux kernel: Vendor: ICSI Model: IC1210 MMC/SD Rev: 1.6F
Jul 2 12:45:36 linux kernel: Type: Direct-Access ANSI SCSI revision: 00
Jul 2 12:45:36 linux kernel: Vendor: ICSI Model: IC1210 SM Rev: 1.6F
Jul 2 12:45:36 linux kernel: Type: Direct-Access ANSI SCSI revision: 00
Jul 2 12:45:36 linux kernel: usb-storage: device scan complete
Jul 2 12:45:36 linux kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Jul 2 12:45:36 linux kernel: Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
Jul 2 12:45:36 linux kernel: SCSI device sdc: 494080 512-byte hdwr sectors (253 MB)
Jul 2 12:45:36 linux kernel: sdc: Write Protect is off
Jul 2 12:45:36 linux kernel: sdc: Mode Sense: 43 00 00 08
Jul 2 12:45:36 linux kernel: sdc: assuming drive cache: write through
Jul 2 12:45:36 linux kernel: SCSI device sdc: 494080 512-byte hdwr sectors (253 MB)
Jul 2 12:45:36 linux kernel: sdc: Write Protect is off
Jul 2 12:45:36 linux kernel: sdc: Mode Sense: 43 00 00 08
Jul 2 12:45:36 linux kernel: sdc: assuming drive cache: write through
Jul 2 12:45:36 linux kernel: sdc: sdc1
Jul 2 12:45:36 linux kernel: Attached scsi removable disk sdc at scsi0, channel 0, id 0, lun 2
Jul 2 12:45:36 linux kernel: Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3
Jul 2 12:45:36 linux kernel: Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Jul 2 12:45:36 linux kernel: Attached scsi generic sg1 at scsi0, channel 0, id 0, lun 1, type 0
Jul 2 12:45:36 linux kernel: Attached scsi generic sg2 at scsi0, channel 0, id 0, lun 2, type 0
Jul 2 12:45:36 linux kernel: Attached scsi generic sg3 at scsi0, channel 0, id 0, lun 3, type 0
Jul 2 12:45:38 linux ifup-route: Warning: Could not set up default route via interface
Jul 2 12:45:38 linux ifup-route: Command ip route replace to default via 192.168.178.1 returned:
Jul 2 12:45:38 linux ifup-route: . RTNETLINK answers: Network is unreachable
Jul 2 12:45:38 linux ifup-route: Configuration line: default 192.168.178.1 - -
Jul 2 12:45:38 linux ifup-route: This needs NOT to be AN ERROR if you set up multiple interfaces.
Jul 2 12:45:38 linux ifup-route: See man 5 routes how to avoid this warning.
Jul 2 12:45:39 linux kernel: nvidia: module not supported by Novell, setting U taint flag.
Jul 2 12:45:39 linux kernel: nvidia: module license 'NVIDIA' taints kernel.
Jul 2 12:45:39 linux kernel: ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
Jul 2 12:45:39 linux kernel: ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 66
Jul 2 12:45:39 linux kernel: PCI: Setting latency timer of device 0000:01:00.0 to 64
Jul 2 12:45:39 linux kernel: NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-7676 Fri Jul 29 13:15:16 PDT 2005
Jul 2 12:45:41 linux kernel: eth1: no IPv6 routers present
Jul 2 12:45:43 linux kernel: wlan0: no IPv6 routers present
Jul 2 12:45:44 linux kdm: :0[5354]: pam_unix2: session started for user lxuser, service xdm-np
Jul 2 12:45:52 linux mDNSResponder (Engineering Build) (Sep 9 2005 17:22:16) [6328]: starting
Jul 2 12:45:52 linux kernel: ACPI: Power Button (FF) [PWRF]
Jul 2 12:45:52 linux kernel: ACPI: Power Button (CM) [PWRB]
Jul 2 12:45:53 linux kernel: IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
Jul 2 12:45:53 linux kernel: IA-32 Microcode Update Driver v1.14 unregistered
Jul 2 12:45:56 linux sshd[6587]: Server listening on :: port 22.
Jul 2 12:46:00 linux smpppd[6507]: smpppd version 1.59 started
Jul 2 12:46:00 linux kernel: smpppd[6636]: segfault at 0000000000520118 rip 00002aaaab3e7600 rsp 00007fffff866c18 error 4
Jul 2 12:46:00 linux /usr/sbin/cron[6692]: (CRON) STARTUP (V5.0)
Jul 2 12:46:01 linux kernel: powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
Jul 2 12:46:01 linux kernel: powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
Jul 2 12:46:01 linux kernel: powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
Jul 2 12:46:01 linux kernel: cpu_init done, current fid 0xa, vid 0x6
Jul 2 12:46:01 linux rcpowersaved: enter 'powernow_k8' into CPUFREQD_MODULE in /etc/sysconfig/powersave/cpufreq.
Jul 2 12:46:01 linux rcpowersaved: this will speed up starting powersaved and avoid unnecessary warnings in syslog.
Jul 2 12:46:02 linux kernel: hdb: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
Jul 2 12:46:02 linux kernel: hdb: drive_cmd: error=0x04 { DriveStatusError }
Jul 2 12:46:02 linux kernel: ide: failed opcode was: 0xef
Jul 2 12:46:03 linux [powersave-set_disk_settings][6857]: WARNING: hdparm returned error '5'
Jul 2 12:46:03 linux hal-subfs-mount[6945]: By hald-subfs-mount created dir /media/SANVOL got removed.
Jul 2 12:46:03 linux hal-subfs-mount[6945]: By hald-subfs-mount created dir /media/floppy got removed.
Jul 2 12:46:03 linux hal-subfs-mount[6945]: SYMLINKS:: disk/by-id/usb-ICSI_IC1210_MMC.SD_0000001 disk/by-path/usb-0000001:0:0:2
Jul 2 12:46:03 linux hal-subfs-mount[6945]: MOUNT_POINT:: /media/SANVOL
Jul 2 12:46:03 linux hal-subfs-mount[6945]: MOUNTPOINT:: /media/SANVOL
Jul 2 12:46:04 linux kernel: subfs 0.9
Jul 2 12:46:04 linux hal-subfs-mount[6945]: Collected mount options and Called(0) /bin/mount -t subfs -o fs=floppyfss,sync,procuid,nosuid,nodev,exec,utf8=true /dev/sdc1 "/media/SANVOL"
Jul 2 12:46:04 linux udevd[2568]: get_netlink_msg: no ACTION in payload found, skip event 'mount'
Jul 2 12:46:05 linux hal-subfs-mount[6965]: MOUNTPOINT:: /media/floppy
Jul 2 12:46:05 linux hal-subfs-mount[6965]: Collected mount options and Called(0) /bin/mount -t subfs -o fs=floppyfss,noatime,procuid,nosuid,nodev,exec /dev/fd0 "/media/floppy"
Jul 2 12:46:06 linux udevd[2568]: get_netlink_msg: no ACTION in payload found, skip event 'mount'
Jul 2 12:46:07 linux udevd[2568]: get_netlink_msg: no ACTION in payload found, skip event 'umount'
Jul 2 12:46:09 linux udevd[2568]: get_netlink_msg: no ACTION in payload found, skip event 'umount'
Jul 2 12:46:13 linux gconfd (lxuser-7007): (Version 2.12.0) wird gestartet, Prozesskennung 7007, Benutzer »lxuser«
Jul 2 12:46:13 linux gconfd (lxuser-7007): Die Adresse »xml:readonly:/etc/opt/gnome/gconf/gconf.xml.mandatory« wurde an der Position 0 zu einer nur lesbaren Konfigurationsquelle aufgelöst
Jul 2 12:46:13 linux gconfd (lxuser-7007): Die Adresse »xml:readwrite:/home/lxuser/.gconf« wurde an der Position 1 zu einer schreibbaren Konfigurationsquelle aufgelöst
Jul 2 12:46:13 linux gconfd (lxuser-7007): Die Adresse »xml:readonly:/etc/opt/gnome/gconf/gconf.xml.defaults« wurde an der Position 2 zu einer nur lesbaren Konfigurationsquelle aufgelöst
Jul 2 12:46:38 linux hp: unable to open /var/run/hpiod.port: No such file or directory: prnt/hpijs/hplip_api.c 75
Jul 2 12:47:15 linux su: (to root) lxuser on /dev/pts/0
Jul 2 12:47:17 linux su: (to root) lxuser on /dev/pts/0
Jul 2 12:47:57 linux su: FAILED SU (to root) lxuser on /dev/pts/1
Jul 2 12:48:05 linux su: (to root) lxuser on /dev/pts/1
Jul 2 12:50:56 linux su: (to root) lxuser on /dev/pts/4
Jul 2 12:50:57 linux su: (to root) lxuser on /dev/pts/4


zum schluss wahr jetzt so das es gegangen (mit ping und anzeige in der Fritzbox) ist bis ich den stecker vom netzwerkkabel gezogen hatte dann sofort eingefroren

Mach mal folgendes: Dabei steht X für das Treibermodul.
Danach poste die Ausgabe des letzten Befehls.

sudo dmesg -c kommt eine lange liste die ich nicht zuordnen kann
sudo /sbin/modprobe X ich hab jetzt das problem das ich den namen nicht mehr weiß es müste aber acx_pci oder wlan0 sein auf beides reagiert er nicht

dmesg macht er keine ausgabe


was ich ganz vergessen habe ich habe ein 64 bit system ,sorry

was heisen die befehle überhaupt?

Das Modul heißt acx_pci.