max-mustermann
Newbie
Hallo Leute,
ich habe auf meinem Laptop SUSE 10.0 und wollte damit ins Internet.
Ich habe schon stundenlang gelesen aber ich komm nicht weiter.
ich hab das ACER 3023WLMI und hab folgendes (durch die Anleitungen die ich im Internet so gefunden habe) ausprobiert:
Als erstes acerhk installiert. Hat, so wies aussieht, geklappt.
dann den ndiswrapper.
Wenn ich ndiswrapper -l eingebe erscheint:
bcmwla driver present, hardware present
dann modprobe acerhk usedritek=1 force_series=3023
echo 1 > /proc/driver/acerhk/wirelessled
und jetzt heißt es in der Anleitung, sollte das LED leuchten... Tut es aber nicht....
Anleitung: http://www.pcwelt.de/wiki/index.php/...r_Linux/German
Könnt ihr mir weiterhelfen??
Bin am Verzweifeln...
und das gibt iwconfig aus:
lo no wireless extensions.
sit0 no wireless extensions.
wlan0 IEEE 802.11g ESSIDff/any Nickname:"linux"
Mode:Managed Frequency:2.412 GHz Access Point: 00:00:00:00:00:00
Bit Rate=54 Mb/s Tx-Power:25 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:3936-3534-3139-3734-3132-3037-36 Security modepen
Power Managementff
Link Quality:100/100 Signal level:-10 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
eth0 no wireless extensions.
und jetzt wirds etwas länger:
dmesg:
inux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fea0000 (usable)
BIOS-e820: 000000001fea0000 - 000000001feae000 (ACPI data)
BIOS-e820: 000000001feae000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
found SMP MP-table at 000f6df0
On node 0 totalpages: 130720
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126624 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6db0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fea81ad
ACPI: FADT (v001 ATI Piranha 0x06040000 ATI 0x000f4240) @ 0x1feade20
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1feade94
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1feadf6a
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x1feadfc4
ACPI: DSDT (v001 ATI SB400 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: local apic disabled
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: APIC at: 0xFEE00000
Processor #0 15:12 APIC version 16
I/O APIC #1 Version 33 at 0xFEC00000.
Processors: 1
Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 vga=0x317 selinux=0 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1800.398 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512704k/522880k available (2028k kernel code, 9588k reserved, 700k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3605.87 BogoMIPS (lpj=7211747)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000010 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Mobile AMD Sempron(tm) Processor 3000+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1718k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0200 (from 0c00)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd63c, last bus=6
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 *11), disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
ACPI: Embedded Controller [EC0] (gpe 3)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:06.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:06.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:07.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:07.0
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:07: ioport range 0x1080-0x1080 has been reserved
pnp: 00:07: ioport range 0x1200-0x120f has been reserved
pnp: 00:07: ioport range 0x500-0x51f has been reserved
pnp: 00:07: ioport range 0x40b-0x40b has been reserved
PCI: Bridge: 0000:00:02.0
IO window: 9000-9fff
MEM window: c0100000-c01fffff
PREFETCH window: c8000000-cfffffff
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:06.0
IO window: 00002000-00002fff
IO window: 00003000-00003fff
PREFETCH window: 20000000-21ffffff
MEM window: 24000000-25ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: c0200000-c02fffff
PREFETCH window: 20000000-22ffffff
PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: 0000:00:06.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:06.0 not available because of resource collisions
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: 0000:00:07.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:07.0 not available because of resource collisions
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt Link [LNKE] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:06:06.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1149190186.972:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
PCI: Setting latency timer of device 0000:00:02.0 to 64
pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
PCI: 0000:00:06.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:06.0 not available because of resource collisions
PCI: 0000:00:07.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:07.0 not available because of resource collisions
vesafb: framebuffer at 0xc8000000, mapped to 0xe0880000, using 6144k, total 65472k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:59d5
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011 bytes,<6>...found (1024x768, 12703 bytes, v3).
Console: switching to colour frame buffer device 127x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303
S2K,PNP0f13S2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:14.6 -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt for device 0000:00:14.6 disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
spurious 8259A interrupt: IRQ7.
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
LID0 SLPB OHC1 OHC2 EHCI P2P MODM
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 204k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdcMA, hddio
Probing IDE interface ide0...
hda: SAMSUNG HM100JC, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
input: AT Translated Set 2 keyboard on isa0060/serio0
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 >
Probing IDE interface ide1...
hdc: Slimtype DVDRW SOSW-833S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
hdc: ATAPI 8X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: Thermal Zone [TZS0] (56 C)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
ACPI: Thermal Zone [TZS1] (44 C)
ACPI: Thermal Zone [TZSV] (47 C)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
udev[2189]: run_program: open /dev/null failed
udev[2189]: run_program: exec of program '/sbin/modprobe' failed
bootsplash: status on console 0 changed to on
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NTFS driver 2.1.23 [Flags: R/W MODULE].
NTFS volume version 3.1.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ndiswrapper: module not supported by Novell, setting U taint flag.
ndiswrapper version 1.2 loaded (preempt=no,smp=no)
ndiswrapper: driver bcmwl5a (Broadcom,12/22/2004, 3.100.46.0) loaded
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI Interrupt 0000:06:05.0[A] -> Link [LNKF] -> GSI 10 (level, low) -> IRQ 10
ndiswrapper: using irq 10
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
wlan0: ndiswrapper ethernet device 00:14:a4:55:77:7f using driver bcmwl5a, configuration file 14E4:4318.5.conf
wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4085 buckets, 32680 max) - 248 bytes per conntrack
lp: driver loaded but no devices found
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 11, io mem 0xc0000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 11, io mem 0xc0001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 2-1: new low speed USB device using ohci_hcd and address 2
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: irq 11, io mem 0xc0002000
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:14.5 -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
usb 2-1: USB disconnect, address 2
ieee1394: Initialized config rom entry `ip1394'
usb 2-1: new low speed USB device using ohci_hcd and address 3
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:06:06.2[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[c0208000-c02087ff] Max Packet=[2048]
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:06:07.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xe13c4400, 00:0a:e4:eb:51:76, IRQ 11
ACPI: PCI Interrupt 0000:06:06.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:06:06.0 [1025:0080]
Yenta: ISA IRQ mask 0x00f8, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x22ffffff
ieee1394: Host added: ID:BUS[0-00:1023] GUID[1234567812345678]
usbcore: registered new driver hiddev
input: USB HID v1.00 Mouse [Cypress Sem PS2/USB Browser Combo Mouse] on usb-0000:00:13.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f
cs: IO port probe 0xa00-0xaff: clean.
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
NET: Registered protocol family 17
mtrr: 0xc8000000,0x4000000 overlaps existing 0xc8000000,0x2000000
wlan0: no IPv6 routers present
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x13 (1075 mV)
cpu_init done, current fid 0xa, vid 0xa
cdrom: This disc doesn't have any tracks I recognize!
Sollte noch dazu sagen, dass ich Hardwarler bin und kein Softi
Danke
Max
ich habe auf meinem Laptop SUSE 10.0 und wollte damit ins Internet.
Ich habe schon stundenlang gelesen aber ich komm nicht weiter.
ich hab das ACER 3023WLMI und hab folgendes (durch die Anleitungen die ich im Internet so gefunden habe) ausprobiert:
Als erstes acerhk installiert. Hat, so wies aussieht, geklappt.
dann den ndiswrapper.
Wenn ich ndiswrapper -l eingebe erscheint:
bcmwla driver present, hardware present
dann modprobe acerhk usedritek=1 force_series=3023
echo 1 > /proc/driver/acerhk/wirelessled
und jetzt heißt es in der Anleitung, sollte das LED leuchten... Tut es aber nicht....
Anleitung: http://www.pcwelt.de/wiki/index.php/...r_Linux/German
Könnt ihr mir weiterhelfen??
Bin am Verzweifeln...
und das gibt iwconfig aus:
lo no wireless extensions.
sit0 no wireless extensions.
wlan0 IEEE 802.11g ESSIDff/any Nickname:"linux"
Mode:Managed Frequency:2.412 GHz Access Point: 00:00:00:00:00:00
Bit Rate=54 Mb/s Tx-Power:25 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:3936-3534-3139-3734-3132-3037-36 Security modepen
Power Managementff
Link Quality:100/100 Signal level:-10 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
eth0 no wireless extensions.
und jetzt wirds etwas länger:
dmesg:
inux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fea0000 (usable)
BIOS-e820: 000000001fea0000 - 000000001feae000 (ACPI data)
BIOS-e820: 000000001feae000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
found SMP MP-table at 000f6df0
On node 0 totalpages: 130720
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126624 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6db0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fea81ad
ACPI: FADT (v001 ATI Piranha 0x06040000 ATI 0x000f4240) @ 0x1feade20
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1feade94
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1feadf6a
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x1feadfc4
ACPI: DSDT (v001 ATI SB400 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: local apic disabled
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: APIC at: 0xFEE00000
Processor #0 15:12 APIC version 16
I/O APIC #1 Version 33 at 0xFEC00000.
Processors: 1
Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 vga=0x317 selinux=0 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1800.398 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512704k/522880k available (2028k kernel code, 9588k reserved, 700k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3605.87 BogoMIPS (lpj=7211747)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000010 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Mobile AMD Sempron(tm) Processor 3000+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1718k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0200 (from 0c00)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd63c, last bus=6
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI-0251: *** Warning: Handle is NULL and Pathname is relative
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 *11), disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
ACPI: Embedded Controller [EC0] (gpe 3)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:06.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:06.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:07.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:07.0
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:07: ioport range 0x1080-0x1080 has been reserved
pnp: 00:07: ioport range 0x1200-0x120f has been reserved
pnp: 00:07: ioport range 0x500-0x51f has been reserved
pnp: 00:07: ioport range 0x40b-0x40b has been reserved
PCI: Bridge: 0000:00:02.0
IO window: 9000-9fff
MEM window: c0100000-c01fffff
PREFETCH window: c8000000-cfffffff
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:06.0
IO window: 00002000-00002fff
IO window: 00003000-00003fff
PREFETCH window: 20000000-21ffffff
MEM window: 24000000-25ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: c0200000-c02fffff
PREFETCH window: 20000000-22ffffff
PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: 0000:00:06.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:06.0 not available because of resource collisions
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: 0000:00:07.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:07.0 not available because of resource collisions
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt Link [LNKE] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:06:06.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1149190186.972:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
PCI: Setting latency timer of device 0000:00:02.0 to 64
pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
PCI: 0000:00:06.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:06.0 not available because of resource collisions
PCI: 0000:00:07.0 has unsupported PM cap regs version (3)
PCI: Device 0000:00:07.0 not available because of resource collisions
vesafb: framebuffer at 0xc8000000, mapped to 0xe0880000, using 6144k, total 65472k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:59d5
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011 bytes,<6>...found (1024x768, 12703 bytes, v3).
Console: switching to colour frame buffer device 127x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303
S2K,PNP0f13S2M] at 0x60,0x64 irq 1,12i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:14.6 -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt for device 0000:00:14.6 disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
spurious 8259A interrupt: IRQ7.
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
LID0 SLPB OHC1 OHC2 EHCI P2P MODM
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 204k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdcMA, hddio
Probing IDE interface ide0...
hda: SAMSUNG HM100JC, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
input: AT Translated Set 2 keyboard on isa0060/serio0
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 >
Probing IDE interface ide1...
hdc: Slimtype DVDRW SOSW-833S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
hdc: ATAPI 8X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: Thermal Zone [TZS0] (56 C)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
ACPI: Thermal Zone [TZS1] (44 C)
ACPI: Thermal Zone [TZSV] (47 C)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
udev[2189]: run_program: open /dev/null failed
udev[2189]: run_program: exec of program '/sbin/modprobe' failed
bootsplash: status on console 0 changed to on
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NTFS driver 2.1.23 [Flags: R/W MODULE].
NTFS volume version 3.1.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ndiswrapper: module not supported by Novell, setting U taint flag.
ndiswrapper version 1.2 loaded (preempt=no,smp=no)
ndiswrapper: driver bcmwl5a (Broadcom,12/22/2004, 3.100.46.0) loaded
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI Interrupt 0000:06:05.0[A] -> Link [LNKF] -> GSI 10 (level, low) -> IRQ 10
ndiswrapper: using irq 10
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
wlan0: ndiswrapper ethernet device 00:14:a4:55:77:7f using driver bcmwl5a, configuration file 14E4:4318.5.conf
wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4085 buckets, 32680 max) - 248 bytes per conntrack
lp: driver loaded but no devices found
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 11, io mem 0xc0000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 11, io mem 0xc0001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 2-1: new low speed USB device using ohci_hcd and address 2
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: irq 11, io mem 0xc0002000
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:14.5 -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
usb 2-1: USB disconnect, address 2
ieee1394: Initialized config rom entry `ip1394'
usb 2-1: new low speed USB device using ohci_hcd and address 3
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:06:06.2[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[c0208000-c02087ff] Max Packet=[2048]
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:06:07.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xe13c4400, 00:0a:e4:eb:51:76, IRQ 11
ACPI: PCI Interrupt 0000:06:06.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:06:06.0 [1025:0080]
Yenta: ISA IRQ mask 0x00f8, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x22ffffff
ieee1394: Host added: ID:BUS[0-00:1023] GUID[1234567812345678]
usbcore: registered new driver hiddev
input: USB HID v1.00 Mouse [Cypress Sem PS2/USB Browser Combo Mouse] on usb-0000:00:13.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f
cs: IO port probe 0xa00-0xaff: clean.
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
NET: Registered protocol family 17
mtrr: 0xc8000000,0x4000000 overlaps existing 0xc8000000,0x2000000
wlan0: no IPv6 routers present
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x13 (1075 mV)
cpu_init done, current fid 0xa, vid 0xa
cdrom: This disc doesn't have any tracks I recognize!
Sollte noch dazu sagen, dass ich Hardwarler bin und kein Softi
Danke
Max