bernieernie2
Newbie
Mayday,
versuche seit tagen über wlan in's netz zu kommen, klappt aber, obwohl ich schon einiges probiert hab, immer noch nicht. Der router mit dsl-anschluss, steht bei meinem nachbarn, lässt sich anpingen, krieg aber trotzdem keinen zugriff auf's www. Poste mal alles was mir halbwegs sinnvoll erscheint (oder auch nicht) :
linux:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:AC
6:E0:E0
inet6 addr: fe80::204:acff:fed6:e0e0/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1649 errors:0 dropped:0 overruns:0 frame:0
TX packets:1649 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:135957 (132.7 Kb) TX bytes:135957 (132.7 Kb)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:11:68:E0
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::212:eff:fe11:68e0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:f3ede000-f3edffff
linux:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:AC6:E0:E0
inet6 addr: fe80::204:acff:fed6:e0e0/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1649 errors:0 dropped:0 overruns:0 frame:0
TX packets:1649 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:135957 (132.7 Kb) TX bytes:135957 (132.7 Kb)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:11:68:E0
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::212:eff:fe11:68e0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:f3ede000-f3edffff
Password:
linux:~ # ifup wlan0
wlan0 device: Texas Instruments ACX 111 54Mbps Wireless Interface
wlan0 configuration: wlan-id-00:12:0e:11:68:e0
ifup-wireless: command 'iwconfig wlan0 key off' returned
ifup-wireless: Error for wireless request "Set Encode" (8B2A) :
ifup-wireless: SET failed on device wlan0 ; Invalid argument.
SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled.
SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEfirewall2 ...
SuSEfirewall2: batch committing...
SuSEfirewall2: Firewall rules successfully set
linux:~ # hwinfo --netcard
16: PCI 10.0: 0200 Ethernet controller
[Created at pci.277]
UDI: /org/freedesktop/Hal/devices/pci_8086_1229
Unique ID: rBUF.ST_bb9LG_k7
SysFS ID: /devices/pci0000:00/0000:00:10.0
SysFS BusID: 0000:00:10.0
Hardware Class: network
Model: "IBM 82558B Ethernet Pro 10/100"
Vendor: pci 0x8086 "Intel Corporation"
Device: pci 0x1229 "82557/8/9 [Ethernet Pro 100]"
SubVendor: pci 0x1014 "IBM"
SubDevice: pci 0x005c "82558B Ethernet Pro 10/100"
Revision: 0x05
Driver: "e100"
Device File: eth0
Memory Range: 0xf3dff000-0xf3dfffff (rw,prefetchable)
I/O Ports: 0x7c60-0x7c7f (rw)
Memory Range: 0xf3f00000-0xf3ffffff (rw,non-prefetchable)
Memory Range: 0x0c100000-0x0c1fffff (ro,prefetchable,disabled)
IRQ: 9 (no events)
HW Address: 00:04:ac:d6:e0:e0
Link detected: no
Module Alias: "pci:v00008086d00001229sv00001014sd0000005Cbc02sc00i00"
Driver Info #0:
Driver Status: e100 is active
Driver Activation Cmd: "modprobe e100"
Driver Info #1:
Driver Status: eepro100 is active
Driver Activation Cmd: "modprobe eepro100"
Config Status: cfg=no, avail=yes, need=no, active=unknown
17: PCI 14.0: 0282 WLAN controller
[Created at pci.277]
UDI: /org/freedesktop/Hal/devices/pci_104c_9066
Unique ID: y9sn.7rrJiCu6tI0
SysFS ID: /devices/pci0000:00/0000:00:14.0
SysFS BusID: 0000:00:14.0
Hardware Class: network
Model: "Abocom ACX 111 54Mbps Wireless Interface"
Vendor: pci 0x104c "Texas Instruments"
Device: pci 0x9066 "ACX 111 54Mbps Wireless Interface"
SubVendor: pci 0x13d1 "Abocom Systems Inc"
SubDevice: pci 0xab90
Driver: "ndiswrapper"
Device File: wlan0
Features: WLAN
Memory Range: 0xf3ede000-0xf3edffff (rw,non-prefetchable)
Memory Range: 0xf3ee0000-0xf3efffff (rw,non-prefetchable)
IRQ: 5 (54378 events)
HW Address: 00:12:0e:11:68:e0
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN bitrates: 22 6 9 12 18 24 36 48 54
WLAN encryption modes: WEP40 WEP104
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pci:v0000104Cd00009066sv000013D1sd0000AB90bc02sc80i00"
Driver Info #0:
Driver Status: acx_pci is active
Driver Activation Cmd: "modprobe acx_pci"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Password:
linux:~ # route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.2.0 * 255.255.255.0 U 0 0 0 wlan0
link-local * 255.255.0.0 U 0 0 0 wlan0
loopback * 255.0.0.0 U 0 0 0 lo
default linux.suse.de 0.0.0.0 UG 0 0 0 wlan0
Mir ist selber klar, daß da einiges nicht so ganz richtig sein kann (linux.suse.de als gateway bei route??????), krieg das nur weder über yast noch per konsole geändert, hab allerdings auch wenig ahnung von der ganzen materie.
Hoffe irgendjemand da draussen kann mir irgendwie helfen. Vielen dank schon mal!
versuche seit tagen über wlan in's netz zu kommen, klappt aber, obwohl ich schon einiges probiert hab, immer noch nicht. Der router mit dsl-anschluss, steht bei meinem nachbarn, lässt sich anpingen, krieg aber trotzdem keinen zugriff auf's www. Poste mal alles was mir halbwegs sinnvoll erscheint (oder auch nicht) :
linux:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:AC
6:E0:E0inet6 addr: fe80::204:acff:fed6:e0e0/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1649 errors:0 dropped:0 overruns:0 frame:0
TX packets:1649 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:135957 (132.7 Kb) TX bytes:135957 (132.7 Kb)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:11:68:E0
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::212:eff:fe11:68e0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:f3ede000-f3edffff
linux:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:AC
6:E0:E0inet6 addr: fe80::204:acff:fed6:e0e0/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1649 errors:0 dropped:0 overruns:0 frame:0
TX packets:1649 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:135957 (132.7 Kb) TX bytes:135957 (132.7 Kb)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:11:68:E0
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::212:eff:fe11:68e0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:f3ede000-f3edffff
Password:
linux:~ # ifup wlan0
wlan0 device: Texas Instruments ACX 111 54Mbps Wireless Interface
wlan0 configuration: wlan-id-00:12:0e:11:68:e0
ifup-wireless: command 'iwconfig wlan0 key off' returned
ifup-wireless: Error for wireless request "Set Encode" (8B2A) :
ifup-wireless: SET failed on device wlan0 ; Invalid argument.
SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled.
SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEfirewall2 ...
SuSEfirewall2: batch committing...
SuSEfirewall2: Firewall rules successfully set
linux:~ # hwinfo --netcard
16: PCI 10.0: 0200 Ethernet controller
[Created at pci.277]
UDI: /org/freedesktop/Hal/devices/pci_8086_1229
Unique ID: rBUF.ST_bb9LG_k7
SysFS ID: /devices/pci0000:00/0000:00:10.0
SysFS BusID: 0000:00:10.0
Hardware Class: network
Model: "IBM 82558B Ethernet Pro 10/100"
Vendor: pci 0x8086 "Intel Corporation"
Device: pci 0x1229 "82557/8/9 [Ethernet Pro 100]"
SubVendor: pci 0x1014 "IBM"
SubDevice: pci 0x005c "82558B Ethernet Pro 10/100"
Revision: 0x05
Driver: "e100"
Device File: eth0
Memory Range: 0xf3dff000-0xf3dfffff (rw,prefetchable)
I/O Ports: 0x7c60-0x7c7f (rw)
Memory Range: 0xf3f00000-0xf3ffffff (rw,non-prefetchable)
Memory Range: 0x0c100000-0x0c1fffff (ro,prefetchable,disabled)
IRQ: 9 (no events)
HW Address: 00:04:ac:d6:e0:e0
Link detected: no
Module Alias: "pci:v00008086d00001229sv00001014sd0000005Cbc02sc00i00"
Driver Info #0:
Driver Status: e100 is active
Driver Activation Cmd: "modprobe e100"
Driver Info #1:
Driver Status: eepro100 is active
Driver Activation Cmd: "modprobe eepro100"
Config Status: cfg=no, avail=yes, need=no, active=unknown
17: PCI 14.0: 0282 WLAN controller
[Created at pci.277]
UDI: /org/freedesktop/Hal/devices/pci_104c_9066
Unique ID: y9sn.7rrJiCu6tI0
SysFS ID: /devices/pci0000:00/0000:00:14.0
SysFS BusID: 0000:00:14.0
Hardware Class: network
Model: "Abocom ACX 111 54Mbps Wireless Interface"
Vendor: pci 0x104c "Texas Instruments"
Device: pci 0x9066 "ACX 111 54Mbps Wireless Interface"
SubVendor: pci 0x13d1 "Abocom Systems Inc"
SubDevice: pci 0xab90
Driver: "ndiswrapper"
Device File: wlan0
Features: WLAN
Memory Range: 0xf3ede000-0xf3edffff (rw,non-prefetchable)
Memory Range: 0xf3ee0000-0xf3efffff (rw,non-prefetchable)
IRQ: 5 (54378 events)
HW Address: 00:12:0e:11:68:e0
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN bitrates: 22 6 9 12 18 24 36 48 54
WLAN encryption modes: WEP40 WEP104
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pci:v0000104Cd00009066sv000013D1sd0000AB90bc02sc80i00"
Driver Info #0:
Driver Status: acx_pci is active
Driver Activation Cmd: "modprobe acx_pci"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Password:
linux:~ # route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.2.0 * 255.255.255.0 U 0 0 0 wlan0
link-local * 255.255.0.0 U 0 0 0 wlan0
loopback * 255.0.0.0 U 0 0 0 lo
default linux.suse.de 0.0.0.0 UG 0 0 0 wlan0
Mir ist selber klar, daß da einiges nicht so ganz richtig sein kann (linux.suse.de als gateway bei route??????), krieg das nur weder über yast noch per konsole geändert, hab allerdings auch wenig ahnung von der ganzen materie.
Hoffe irgendjemand da draussen kann mir irgendwie helfen. Vielen dank schon mal!
