schoerch
Newbie
Hallo,
ich habe Probleme die interne WLAN Karte auf meinem Toshiba SP6100 via WPA-PSK zum laufen zu bekommen. Unter Windows XP mit dem Agere 2-2.3 Treiber (v7.84) funktioniert es ohne Probleme.
Der zu verbindende AP läuft im Mixed (11b+11g) Mode mit WPA-PSK only. (Geht nicht anders, da es noch einen zweiten Client (11g) gibt)
Was mich verwundert, das mir unter YaST bei der Karte nach dem YOU durchlauf und Reboot WPA-PSK angeboten wird. (War vorher nicht)
-------------YaST - Netzwekkonfiguration------------
TOSHIBA Wireless LAN Card
Gerätename : wlan-id-xx:xx:xx:xx:xx:xx
Name der Hardware-Konfiguration: bus-pcmcia-0.0
Modulname : hostap_cs
-------------------------------------------------------
Allderdings gibt mir dmesg fogendes aus..
--------------dmesg----------------------------------------
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
eth1: Hardware identity 0005:0004:0005:0000
eth1: Station identity 001f:0001:0008:000a
eth1: Firmware determined as Lucent/Agere 8.10
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address xx:xx:xx:xx:xx:xx
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 11, io 0xd000-0xd03f
------------------------------------------------------------
Zusehen ist da auch 104-bit key - bug ?
Beim Starten ders Interfaces kommt folgendes:
------------------------------------------------------------
# ifup eth1
eth1
eth1 configuration: wlan-id-xx:xx:xx:xx:xx:xx
eth1 warning: WPA configured but may be unsupported
eth1 warning: by this device
eth1 starting wpa_supplicant
WEXT auth param 7 value 0x1 - ioctl[SIOCSIWAUTH]: Operation not supported
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x1 - ioctl[SIOCSIWAUTH]: Operation not supported
--------------------------------------------------------------------
Die Karte läuft unter WinXP defintiv mit WPA. Diesen Agere Treiber nutze ich schon seit einger Zeit unter Windows XP. Der hat mir u.a. die Cannels aufgebohrt und läuft schneller.
Was läuft da falsch? Wie muß ich wo, was anpassen?
mfg Schoerch
ich habe Probleme die interne WLAN Karte auf meinem Toshiba SP6100 via WPA-PSK zum laufen zu bekommen. Unter Windows XP mit dem Agere 2-2.3 Treiber (v7.84) funktioniert es ohne Probleme.
Der zu verbindende AP läuft im Mixed (11b+11g) Mode mit WPA-PSK only. (Geht nicht anders, da es noch einen zweiten Client (11g) gibt)
Was mich verwundert, das mir unter YaST bei der Karte nach dem YOU durchlauf und Reboot WPA-PSK angeboten wird. (War vorher nicht)
-------------YaST - Netzwekkonfiguration------------
TOSHIBA Wireless LAN Card
Gerätename : wlan-id-xx:xx:xx:xx:xx:xx
Name der Hardware-Konfiguration: bus-pcmcia-0.0
Modulname : hostap_cs
-------------------------------------------------------
Allderdings gibt mir dmesg fogendes aus..
--------------dmesg----------------------------------------
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
eth1: Hardware identity 0005:0004:0005:0000
eth1: Station identity 001f:0001:0008:000a
eth1: Firmware determined as Lucent/Agere 8.10
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address xx:xx:xx:xx:xx:xx
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 11, io 0xd000-0xd03f
------------------------------------------------------------
Zusehen ist da auch 104-bit key - bug ?
Beim Starten ders Interfaces kommt folgendes:
------------------------------------------------------------
# ifup eth1
eth1
eth1 configuration: wlan-id-xx:xx:xx:xx:xx:xx
eth1 warning: WPA configured but may be unsupported
eth1 warning: by this device
eth1 starting wpa_supplicant
WEXT auth param 7 value 0x1 - ioctl[SIOCSIWAUTH]: Operation not supported
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Operation not supported
ioctl[SIOCSIWENCODE]: Invalid argument
WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x1 - ioctl[SIOCSIWAUTH]: Operation not supported
--------------------------------------------------------------------
Die Karte läuft unter WinXP defintiv mit WPA. Diesen Agere Treiber nutze ich schon seit einger Zeit unter Windows XP. Der hat mir u.a. die Cannels aufgebohrt und läuft schneller.
Was läuft da falsch? Wie muß ich wo, was anpassen?
mfg Schoerch