Wo finde ich das Modul ACM? Microlink 56k Fun USB (Sorry!)

Anonymous schrieb:

Mit dieser Anleitung sollte es funktionieren:

USB Modem Konfiguration (ELSA USB Modem)
----------------------------------------
Hintergrund: Das ELSA USB Modem ist zwar kein Winmodem, jedoch kommt es offensichtlich zu Timingproblemen. Daher wird das Kernel Modul "acm" nicht geladen und damit das Modem vom Kernel 2.4.21 (bei smp4G für Intel P4, 2.8 HT, Northwood) nicht erkannt.
Dies kann zwar manuell mittels "modprobe acm" erreicht werden. Jedoch ist dies auf Dauer kein Zustand. Die folgende Vorgehensweise ist nur sinnvoll falls dieses Modem wirklich am USB-Port hängt.

1. System -> YAST -> System -> Editor für /etc/sysconfig Dateien starten

2. Hardware -> Hotplug -> HOTPLUG_USB_STATIC_MODULES ergänzen
um den Eintrag: acm
Bsp. für den Eintrag: "evdev joydev mousedev keybdev acm"

3. Danach System neu starten

Hinweis:
System kann beim 1. Mal u.U. nicht ganz richtig herunterfahren. Sollte aber nach dem Restart behoben sein.

Kommt es dennoch vor, dass das Modem nach Wiedereinwahl nicht erkannt wird, so muss manuell (root-Rechte) mittels:
modprobe -r acm
modprobe acm
das Kernelmodul entladen und wieder geladen werden.

Falls das Modem immer noch nicht erkannt wird, kann vorsichtig folgendes eingegeben werden:
modprobe -r usbcore
modprobe -r usb-uhci
modprobe usbcore
modprobe usb-uhci

Zum Vergrößern anklicken....

• Linux version 2.6.8-24-default (geeko@buildhost) (gcc version 3.3.4 (pre 3.3.5 20040809)) #1 Wed Oct 6 09:16:23 UTC 2004
  BIOS-provided physical RAM map:
  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
  BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
  BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
  757MB vmalloc/ioremap area available.
  0MB HIGHMEM available.
  255MB LOWMEM available.
  On node 0 totalpages: 65520
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 61424 pages, LIFO batch:14
  HighMem zone: 0 pages, LIFO batch:1
  DMI 2.3 present.
  ACPI: RSDP (v000 AMI ) @ 0x000fa920
  ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x0fff0000
  ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x0fff0030
  ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x0fff00c0
  ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
  ACPI: PM-Timer IO Port: 0x808
  ACPI: local apic disabled
  Built 1 zonelists
  Kernel command line: root=/dev/hdb5 vga=0x317 selinux=0 resume=/dev/hda5 desktop elevator=as splash=silent
  bootsplash: silent mode.
  Initializing CPU#0
  PID hash table entries: 1024 (order: 10, 16384 bytes)
  Detected 1537.341 MHz processor.
  Using pmtmr for high-res timesource
  Console: colour dummy device 80x25
  Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  Memory: 254284k/262080k available (2074k kernel code, 7092k reserved, 782k data, 212k init, 0k highmem)
  Checking if this processor honours the WP bit even in supervisor mode... Ok.
  Calibrating delay loop... 3039.23 BogoMIPS (lpj=1519616)
  Security Scaffold v1.0.0 initialized
  SELinux: Disabled at boot.
  Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
  CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
  CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
  CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
  CPU: L2 Cache: 256K (64 bytes/line)
  CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
  Intel machine check architecture supported.
  Intel machine check reporting enabled on CPU#0.
  CPU: AMD Athlon(tm) XP 1800+ stepping 00
  Enabling fast FPU save and restore... done.
  Enabling unmasked SIMD FPU exception support... done.
  Checking 'hlt' instruction... OK.
  ACPI: IRQ9 SCI: Edge set to Level Trigger.
  checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
  Looking for DSDT in initrd ...No customized DSDT found in initrd!
  Freeing initrd memory: 1133k freed
  NET: Registered protocol family 16
  PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
  PCI: Using configuration type 1
  mtrr: v2.0 (20020519)
  ACPI: Subsystem revision 20040715
  ACPI: Interpreter enabled
  ACPI: Using PIC for interrupt routing
  ACPI: PCI Root Bridge [PCI0] (00:00)
  PCI: Probing PCI hardware (bus 00)
  ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
  ACPI: Power Resource [URP1] (off)
  ACPI: Power Resource [URP2] (off)
  ACPI: Power Resource [FDDP] (off)
  ACPI: Power Resource [LPTP] (off)
  ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
  ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
  ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
  ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
  Linux Plug and Play Support v0.97 (c) Adam Belay
  PCI: Using ACPI for IRQ routing
  ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
  ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
  ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
  ACPI: PCI interrupt 0000:00:08.2 -> GSI 11 (level, low) -> IRQ 11
  ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
  ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 5 (level, low) -> IRQ 5
  ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 11 (level, low) -> IRQ 11
  ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
  ACPI: PCI interrupt 0000:00:10.1 -> GSI 10 (level, low) -> IRQ 10
  ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 5 (level, low) -> IRQ 5
  ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 10 (level, low) -> IRQ 10
  ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
  ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
  TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
  apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
  apm: overridden by ACPI.
  audit: initializing netlink socket (disabled)
  audit(1129568739.327:0): initialized
  Total HugeTLB memory allocated, 0
  VFS: Disk quotas dquot_6.5.1
  Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  Initializing Cryptographic API
  vesafb: framebuffer at 0xd8000000, mapped to 0xd0880000, using 6144k, total 65536k
  vesafb: mode is 1024x768x16, linelength=2048, pages=1
  vesafb: protected mode interface info at c000:e740
  vesafb: scrolling: redraw
  vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
  bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 35007 bytes,<6>...found (1024x768, 21643 bytes, v3).
  Console: switching to colour frame buffer device 127x43
  fb0: VESA VGA frame buffer device
  isapnp: Scanning for PnP cards...
  isapnp: No Plug & Play device found
  Real Time Clock Driver v1.12
  serio: i8042 KBD port at 0x60,0x64 irq 1
  serio: i8042 AUX port at 0x60,0x64 irq 12
  Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
  ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
  ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
  Using anticipatory io scheduler
  Floppy drive(s): fd0 is 1.44M
  FDC 0 is a post-1991 82077
  RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
  loop: loaded (max 8 devices)
  Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
  ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
  VP_IDE: IDE controller at PCI slot 0000:00:11.1
  ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
  VP_IDE: chipset revision 6
  VP_IDE: not 100% native mode: will probe irqs later
  VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
  ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hdaMA, hdbMA
  ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdcMA, hddio
  Probing IDE interface ide0...
  hda: ExcelStor Technology J240, ATA DISK drive
  hdb: Maxtor 6Y060L0, ATA DISK drive
  ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
  Probing IDE interface ide1...
  hdc: BENQ DVD DD DW1620, ATAPI CD/DVD-ROM drive
  ide1 at 0x170-0x177,0x376 on irq 15
  Probing IDE interface ide2...
  ide2: Wait for ready failed before probe !
  Probing IDE interface ide3...
  ide3: Wait for ready failed before probe !
  Probing IDE interface ide4...
  ide4: Wait for ready failed before probe !
  Probing IDE interface ide5...
  ide5: Wait for ready failed before probe !
  hda: max request size: 128KiB
  hda: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
  hda: cache flushes supported
  hda: hda1 hda2 < hda5 hda6 >
  hdb: max request size: 128KiB
  hdb: 120103200 sectors (61492 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
  hdb: cache flushes supported
  hdb: hdb1 hdb2 < hdb5 >
  ide-floppy driver 0.99.newide
  mice: PS/2 mouse device common for all mice
  input: AT Translated Set 2 keyboard on isa0060/serio0
  alps.c: E6 report: 4c 03 c8
  input: PS2++ Logitech MX Mouse on isa0060/serio1
  input: PC Speaker
  md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
  NET: Registered protocol family 2
  IP: routing cache hash table of 2048 buckets, 16Kbytes
  TCP: Hash tables configured (established 16384 bind 32768)
  NET: Registered protocol family 1
  NET: Registered protocol family 8
  NET: Registered protocol family 20
  PM: Reading pmdisk image.
  swsusp: Resume From Partition: /dev/hda5
  <3>swsusp: Invalid partition type.
  pmdisk: Error -22 resuming
  PM: Resume from disk failed.
  ACPI: (supports S0 S1 S4 S5)
  ACPI wakeup devices:
  PCI0 UAR1 USB1 USB2 USB3 EHCI USB USBA USBB AC9 MC9 ILAN SLPB
  md: Autodetecting RAID arrays.
  md: autorun ...
  md: ... autorun DONE.
  RAMDISK: Compressed image found at block 0
  VFS: Mounted root (ext2 filesystem).
  kjournald starting. Commit interval 5 seconds
  EXT3-fs: mounted filesystem with ordered data mode.
  VFS: Mounted root (ext3 filesystem) readonly.
  Trying to move old root to /initrd ... failed
  Unmounting old root
  Trying to free ramdisk memory ... okay
  Freeing unused kernel memory: 212k freed
  Adding 1052216k swap on /dev/hda5. Priority:42 extents:1
  EXT3 FS on hdb5, internal journal
  8139too Fast Ethernet driver 0.9.27
  ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 5 (level, low) -> IRQ 5
  eth0: RealTek RTL8139 at 0xd0806700, 00:11:6b:30:f8:f5, IRQ 5
  eth0: Identified 8139 chip type 'RTL-8100B/8139D'
  usbcore: registered new driver usbfs
  usbcore: registered new driver hub
  md: Autodetecting RAID arrays.
  md: autorun ...
  md: ... autorun DONE.
  device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
  NTFS driver 2.1.17 [Flags: R/O MODULE].
  NTFS volume version 3.1.
  NTFS volume version 3.1.
  subfs 0.9
  evdev_connect: evdev c127a8a0 handle c127a8bc name event0
  evdev_connect: evdev c127a7a0 handle c127a7bc name event1
  evdev_connect: evdev c127a6a0 handle c127a6bc name event2
  gameport: pci0000:00:08.1 speed 1217 kHz
  NET: Registered protocol family 23
  via_ircc: unsupported module, tainting kernel.
  Linux agpgart interface v0.100 (c) Dave Jones
  agpgart: Detected VIA KT266/KY266x/KT333 chipset
  agpgart: Maximum main memory to use for agp memory: 203M
  agpgart: AGP aperture is 128M @ 0xe0000000
  USB Universal Host Controller Interface driver v2.2
  ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 11 (level, low) -> IRQ 11
  uhci_hcd 0000:00:10.0: UHCI Host Controller
  uhci_hcd 0000:00:10.0: irq 11, io base 0000d800
  uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
  usb usb1: Product: UHCI Host Controller
  usb usb1: Manufacturer: Linux 2.6.8-24-default uhci_hcd
  usb usb1: SerialNumber: 0000:00:10.0
  hub 1-0:1.0: USB hub found
  hub 1-0:1.0: 2 ports detected
  ACPI: PCI interrupt 0000:00:10.1 -> GSI 10 (level, low) -> IRQ 10
  uhci_hcd 0000:00:10.1: UHCI Host Controller
  uhci_hcd 0000:00:10.1: irq 10, io base 0000dc00
  uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
  usb usb2: Product: UHCI Host Controller
  usb usb2: Manufacturer: Linux 2.6.8-24-default uhci_hcd
  usb usb2: SerialNumber: 0000:00:10.1
  hub 2-0:1.0: USB hub found
  hub 2-0:1.0: 2 ports detected
  ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 5 (level, low) -> IRQ 5
  uhci_hcd 0000:00:10.2: UHCI Host Controller
  uhci_hcd 0000:00:10.2: irq 5, io base 0000e000
  uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
  usb usb3: Product: UHCI Host Controller
  usb usb3: Manufacturer: Linux 2.6.8-24-default uhci_hcd
  usb usb3: SerialNumber: 0000:00:10.2
  hub 3-0:1.0: USB hub found
  hub 3-0:1.0: 2 ports detected
  ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 10 (level, low) -> IRQ 10
  ehci_hcd 0000:00:10.3: EHCI Host Controller
  ehci_hcd 0000:00:10.3: irq 10, pci mem d1118600
  usb 3-1: new full speed USB device using address 2
  ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
  ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
  usb usb4: Product: EHCI Host Controller
  usb usb4: Manufacturer: Linux 2.6.8-24-default ehci_hcd
  usb usb4: SerialNumber: 0000:00:10.3
  hub 4-0:1.0: USB hub found
  hub 4-0:1.0: 6 ports detected
  ieee1394: Initialized config rom entry `ip1394'
  ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
  ACPI: PCI interrupt 0000:00:08.2 -> GSI 11 (level, low) -> IRQ 11
  ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[dffff800-dfffffff] Max Packet=[2048]
  usb 3-1: device not accepting address 2, error -71
  hub 4-0:1.0: over-current change on port 3
  hub 4-0:1.0: over-current change on port 4
  usb 3-1: new full speed USB device using address 4
  ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0021018a75]
  eth0: link down
  NET: Registered protocol family 17
  hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
  Uniform CD-ROM driver Revision: 3.20
  SCSI subsystem initialized
  st: Version 20040403, fixed bufsize 32768, s/g segs 256
  slusb: unsupported module, tainting kernel.
  slusb: module license 'Smart Link Ltd.' taints kernel.
  ST7554 USB Modem.
  st7554 probe: cannot initialize device.
  ST7554 USB Modem: probe of 3-1:1.0 failed with error -12
  usbcore: registered new driver ST7554 USB Modem
  BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
  ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
  ACPI: Power Button (FF) [PWRF]
  ACPI: Sleep Button (CM) [SLPB]
  ACPI: Processor [CPU1] (supports C1, 16 throttling states)
  powernow-k8: Processor cpuid 680 not supported
  parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
  parport0: irq 7 detected
  parport0: Printer, Canon S450
  
  lp0: using parport0 (polling).
  drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
  usbcore: registered new driver usbserial_generic
  usbcore: registered new driver usbserial
  drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
  Non-volatile memory driver v1.2
  end_request: I/O error, dev fd0, sector 0
  end_request: I/O error, dev fd0, sector 0
  bootsplash: status on console 0 changed to on
  NET: Registered protocol family 10
  Disabled Privacy Extensions on device c037f6a0(lo)
  IPv6 over IPv4 tunneling driver
  Disabled Privacy Extensions on device ce9bbc00(sit0)
  eth0: no IPv6 routers present
  
  

Habe auch noch die Datei hotplug.log, kann ich aber unter windows nicht ordentlich formatieren.

Dank USB-Modem kenne ich mich an meinem dritten Linux-Tag schon mal einigermaßen mit der Konsole, Yast, XEmacs dem Dateisystem und einigen Kommandos aus . Wäre schön, wenn das blöde Modem dann irgendwann auch noch unter Linux funktionieren würde.

Grüße, Koller.

Bonsai schrieb:

Allerdings muss dazu schon der Teil USB>Seriell laufen.

Zum Vergrößern anklicken....