jhr-online
Newbie
Hallo erstmal,
ich hoffe hier eine Lösung für mein Problem zu bekommen. Ich komme einfach nicht dahinter:
Debian sarge, AMD Duron 700, eth0 für pppoe (t-online), eth1 für LAN (Hub). Installiert ist hostap, hostap-utils, wireless-utils, hostapd. Und hier mal ein paar Outputs:
So, folgendes Problem: Ich kann verbinden. Aufgrund der Entfernung zwischen Client und dem oben beschriebenen Server ist nur eine schlecht Verbindung möglich, aber immerhin verbindet er. Der Client sendet sich allerdings doof und empfängt nichts. Meine Frage also: Ist das ein WLan-Problem (Zu schlechter Empfang etc.) oder hab ich was falsch eingestellt?
edit:
Ich hab gerade noch was in der syslog gefunden:
dazwischen vergingen allerdings gerade mal 8 Sekunden... :shock:
ich hoffe hier eine Lösung für mein Problem zu bekommen. Ich komme einfach nicht dahinter:
Debian sarge, AMD Duron 700, eth0 für pppoe (t-online), eth1 für LAN (Hub). Installiert ist hostap, hostap-utils, wireless-utils, hostapd. Und hier mal ein paar Outputs:
Code:
hostapd.conf
interface=wlan0
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
debug=0
dump_file=/tmp/hostapd.dump
ssid=jhr-net
macaddr_acl=1
accept_mac_file=/etc/hostapd/hostapd.accept
deny_mac_file=/etc/hostapd/hostapd.deny
Code:
iwconfig
wifi0 IEEE 802.11b ESSID:"jhr-net"
Mode:Master Frequency:2.422 GHz Access Point: 00:09:5B:68:E8:0D
Bit Rate:11 Mb/s Sensitivity=1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:3 Invalid misc:78 Missed beacon:0
wlan0 IEEE 802.11b ESSID:"jhr-net"
Mode:Master Frequency:2.422 GHz Access Point: 00:09:5B:68:E8:0D
Bit Rate:11 Mb/s Sensitivity=1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:3 Invalid misc:78 Missed beacon:0
Code:
dhcpd.conf
default-lease-time 21600;
max-lease-time 43200;
authoritative;
# LAN
subnet 192.168.1.0 netmask 255.255.255.0 {
# --- default getaway
option domain-name "jhr-online.dyndns.org";
option routers 192.168.1.1;
option subnet-mask 255.255.255.0;
option broadcast-address 192.168.1.255;
option netbios-name-servers 192.168.1.1;
option domain-name-servers 192.168.1.1;
range 192.168.1.10 192.168.1.19;
}
# WLAN
subnet 192.168.2.0 netmask 255.255.255.0 {
option domain-name "jhr-online.dyndns.org";
option routers 192.168.2.1;
option subnet-mask 255.255.255.0;
option broadcast-address 192.168.2.255;
option domain-name-servers 192.168.2.1;
option netbios-name-servers 192.168.2.1;
range 192.168.2.10 192.168.2.19;
}
edit:
Ich hab gerade noch was in der syslog gefunden:
Code:
kernel: wifi0: enabling hostapd mode
kernel: wifi0: registered netdevice wlan0ap
kernel: wifi0: disabling hostapd mode