• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst] HP Wireless Adapter - Netzwerkdrucker druckt nicht

A

adda

Member
Ich benutze HP Officejet 5600 series mit driver HP cups 3.11.10 und als HPFAX mit driver HP Fax hpijs

Jetzt habe ich mir"HP Wireless Printing Upgrade KIT" gekauft und konfiguriert,
indem ich einen dritten HP Officejet 5600 als Netzwerkdrucker hinzugefügt habe.

Wenn ich drahtlos drucken will, bekomme ich folgende Antwort:

"waitung for job to complete"
Habe Bildschirmfotos, die ich nachsenden kann, ween ich weiß, wohin

Netzwerkeinrichtung scheint OK
Nur der Drucker hat keinen Kontakt mit dem Cups server (?)

Noch zur erläuterung:
Mein DSL ist tatsächlich LTE von Vodafone mit Easybox 803 und FM 300
(Downloadgeschwindigkeit 900 kb) - 7200 Kbit/s

Jetzt Angaben (ohne Bildschirmfotos)

WLAN = ifconfig (nur für wireless Adapter)
wlan1 Link encap:Ethernet Hardware Adresse 00:17:08:9A:B3:41
inet Adresse:192.168.2.102 Bcast:192.168.2.255 Maske:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2286 errors:0 dropped:0 overruns:0 frame:0
TX packets:63 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 Sendewarteschlangenlänge:1000
RX bytes:439748 (429.4 Kb) TX bytes:11253 (10.9 Kb)

ip a =
4: wlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:17:08:9a:b3:41 brd ff:ff:ff:ff:ff:ff
inet 192.168.2.102/24 brd 192.168.2.255 scope global wlan1

hwinfo --usb (nur wireless Adapter)
15: USB 00.0: 0000 Unclassified device
[Created at usb.122]
Unique ID: 7bWa.PPWnE1n8qjF
Parent ID: pBe4.22MfGOBVe10
SysFS ID: /devices/pci0000:00/0000:00:10.4/usb2/2-3/2-3:1.0
SysFS BusID: 2-3:1.0
Hardware Class: unknown
Model: "HP Wireless Adapter"
Hotplug: USB
Vendor: usb 0x03f0 "HP"
Device: usb 0xca02 "Wireless Adapter"
Revision: "1.00"
Serial ID: "0017089AB341"
Driver: "rtl8187"
Driver Modules: "rtl8187"
Device File: wlan1
Speed: 480 Mbps
HW Address: 00:17:08:9a:b3:41
Link detected: yes
Module Alias: "usb:v03F0pCA02d0100dc00dsc00dp00ic00isc00ip00"
Driver Info #0:
Driver Status: rtl8187 is active
Driver Activation Cmd: "modprobe rtl8187"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #6 (Hub)


collecNWData

Code: 
[code]
collectNWData.sh V0.6.5.4.6 (Rev: 1.299, Build: 2011-11-20 18:25:03 UTC)
--- Which type of your network connection should be tested?
--- (2) Wireless connection (WLAN)
--- What's the type of networktopology?
--- (3) WLAN access point <---> LinuxRouter <---> LinuxClient
--- On which host is the script executed?
--- (1) LinuxClient
--- WLAN SSID to connect to: §§§§§§§§1

--- NWEliza is analyzing the system for common network configuration errors ...

!!! CND0100E: No network card for the selected connection type was found on the system

--- Go to http://www.linux-tips-and-tricks.de/CND to get more detailed instructions 
--- about the error/warning messages and how to fix the problems on your own.

--- If you are unsuccessful then place the contents of file collectNWData.txt in the net
--- (see http://www.linux-tips-and-tricks.de/CND_UPL for links) 
--- and then paste the nopaste link on your favorite Linux forum.

==================================================================================================================
===== cat /etc/*[-_]release || cat /etc/*[-_]version =============================================================
/etc/os-release
/etc/SuSE-release
NAME=openSUSE
VERSION = 12.1 (Asparagus)
VERSION_ID="12.1"
PRETTY_NAME="openSUSE 12.1 (Asparagus) (i586)"
ID=opensuse
openSUSE 12.1 (i586)
VERSION = 12.1
CODENAME = Asparagus
===== uname -a ===================================================================================================
Linux biberbau 3.1.9-1.4-default #1 SMP Fri Jan 27 08:55:10 UTC 2012 (efb5ff4) i686 i686 i386 GNU/Linux
===== lspci ======================================================================================================
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 78)
	Subsystem: ASRock Incorporation K7VT6 motherboard [1849:3065]
	Kernel driver in use: via-rhine
===== lsusb | grep -v "root hub" =================================================================================
Bus 001 Device 003: ID 057c:8401 AVM GmbH AVM Fritz!WLAN N [Atheros AR9001U]
Bus 002 Device 002: ID 03f0:ca02 Hewlett-Packard 
===== hwinfo (filtered) ==========================================================================================
31: PCI 12.0: 0200 Ethernet controller
  Model: "VIA VT6102 [Rhine-II]"
  Vendor: pci 0x1106 "VIA Technologies, Inc."
  Device: pci 0x3065 "VT6102 [Rhine-II]"
  SubVendor: pci 0x1849 "ASRock Incorporation"
  SubDevice: pci 0x3065 "K7VT6 motherboard"
  Driver: "via-rhine"
  Driver Modules: "via_rhine"
  Device File: eth0
  Link detected: no
    Driver Status: via-rhine is active
    Driver Activation Cmd: "modprobe via-rhine"
57: USB 00.0: 0282 WLAN controller
  Model: "AVM FRITZ!WLAN USB Stick N"
  Vendor: usb 0x057c "AVM GmbH"
  Device: usb 0x8401 "FRITZ!WLAN USB Stick N"
  Driver: "carl9170"
  Driver Modules: "carl9170"
  Device File: wlan0
  Link detected: yes
    Driver Status: carl9170 is active
    Driver Activation Cmd: "modprobe carl9170"
58: USB 00.0: 0282 WLAN controller
  Model: "HP Wireless Adapter"
  Vendor: usb 0x03f0 "HP"
  Device: usb 0xca02 "Wireless Adapter"
  Driver: "rtl8187"
  Driver Modules: "rtl8187"
  Device File: wlan1
  Link detected: yes
    Driver Status: rtl8187 is active
    Driver Activation Cmd: "modprobe rtl8187"
===== lsmod (filtered) ===========================================================================================
| ac97_bus        | af_packet       | arc4            | ath             | binfmt_misc      |
| carl9170        | cfg80211        | eeprom_93cx6    | ehci_hcd        | emu10k1_gp       |
| fglrx           | hwmon           | i2c_core        | i2c_viapro      | ip_tables        |
| libata          | mac80211        | microcode       | mperf           | ns558            |
| ohci_hcd        | pci_hotplug     | ppdev           | rfkill          | rtl8187          |
| sata_via        | sg              | shpchp          | sr_mod          | uhci_hcd         |
| usb_storage     | via_rhine       |
===== ls /lib/firmware/* =========================================================================================
| 3.1.0-1.2-default       | 3.1.9-1.4-default       | 3com                    | acenic                   |
| adaptec                 | advansys                | agere_ap_fw.bin         | agere_sta_fw.bin         |
| aica_firmware.bin       | amd-ucode               | ar3k                    | ar7010_1_1.fw            |
| ar7010.fw               | ar9170-1.fw             | ar9170-2.fw             | ar9271.fw                |
| asihpi                  | ath3k-1.fw              | ath6k                   | av7110                   |
| bnx2                    | bnx2x                   | bnx2x-e1-4.8.53.0.fw    | bnx2x-e1-5.2.13.0.fw     |
| bnx2x-e1-5.2.7.0.fw     | bnx2x-e1h-4.8.53.0.fw   | bnx2x-e1h-5.2.13.0.fw   | bnx2x-e1h-5.2.7.0.fw     |
| brcm                    | carl9170-1.fw           | cis                     | cpia2                    |
| cxgb3                   | cxgb4                   | dabusb                  | digiface_firmware.bin    |
| digiface_firmware_rev11.bin| dsp56k                  | dvb-fe-xc5000-1.6.114.fw| dvb-usb-dib0700-1.20.fw  |
| dvb-usb-terratec-h5-drxk.fw| e100                    | ea                      | edgeport                 |
| emagic                  | emi26                   | emi62                   | emu                      |
| ene-ub6250              | ess                     | f2255usb.bin            | GPL-3                    |
| htc_7010.fw             | htc_9271.fw             | i2400m-fw-usb-1.4.sbcf  | i2400m-fw-usb-1.5.sbcf   |
| i6050-fw-usb-1.5.sbcf   | intelliport2.bin        | iwlwifi-1000-3.ucode    | iwlwifi-1000-5.ucode     |
| iwlwifi-100-5.ucode     | iwlwifi-3945-2.ucode    | iwlwifi-4965-1.ucode    | iwlwifi-4965-2.ucode     |
| iwlwifi-5000-1.ucode    | iwlwifi-5000-2.ucode    | iwlwifi-5000-5.ucode    | iwlwifi-5150-2.ucode     |
| iwlwifi-6000-4.ucode    | iwlwifi-6000g2a-5.ucode | iwlwifi-6000g2b-5.ucode | iwlwifi-6050-4.ucode     |
| iwlwifi-6050-5.ucode    | kaweth                  | keyspan                 | keyspan_pda              |
| korg                    | lgs8g75.fw              | libertas                | LICENCE.agere            |
| LICENCE.atheros_firmware| LICENCE.broadcom_bcm43xx| LICENCE.chelsio_firmware| LICENCE.ene_firmware     |
| LICENCE.i2400m          | LICENCE.iwlwifi_firmware| LICENCE.Marvell         | LICENCE.mwl8335          |
| LICENCE.myri10ge_firmware| LICENCE.OLPC            | LICENCE.phanfw          | LICENCE.qla2xxx          |
| LICENCE.ralink-firmware.txt| LICENCE.rtlwifi_firmware.txt| LICENCE.tda7706-firmware.txt| LICENCE.ti-connectivity  |
| LICENCE.ueagle-atm4-firmware| LICENCE.via_vt6656      | LICENCE.xc5000          | LICENSE.dib0700          |
| LICENSE.radeon_rlc      | matrox                  | microcode.dat           | mixart                   |
| mrvl                    | mts_mt9234mu.fw         | mts_mt9234zba.fw        | multiface_firmware.bin   |
| multiface_firmware_rev11.bin| mwl8335_duplex.fw       | mwl8k                   | myri10ge_ethp_z8e.dat    |
| myri10ge_eth_z8e.dat    | myri10ge_rss_ethp_z8e.dat| myri10ge_rss_eth_z8e.dat| myricom                  |
| ositech                 | pcxhr                   | phanfw.bin              | ql2100_fw.bin            |
| ql2200_fw.bin           | ql2300_fw.bin           | ql2322_fw.bin           | ql2400_fw.bin            |
| ql2500_fw.bin           | qlogic                  | r128                    | radeon                   |
| rpm_firmware.bin        | rt2561.bin              | rt2561s.bin             | rt2661.bin               |
| rt2860.bin              | rt2870.bin              | rt3070.bin              | rt3071.bin               |
| rt3090.bin              | rt73.bin                | RTL8192E                | RTL8192SU                |
| rtl_nic                 | rtlwifi                 | s2250.fw                | s2250_loader.fw          |
| sb16                    | slicoss                 | sun                     | sxg                      |
| TDA7706_OM_v2.5.1_boot.txt| TDA7706_OM_v3.0.2_boot.txt| tehuti                  | ti-connectivity          |
| tigon                   | tlg2300_firmware.bin    | ttusb-budget            | ueagle-atm               |
| usbdux                  | usbduxfast_firmware.bin | usbdux_firmware.bin     | v4l-cx231xx-avcore-01.fw |
| v4l-cx23418-apu.fw      | v4l-cx23418-cpu.fw      | v4l-cx23418-dig.fw      | v4l-cx23885-avcore-01.fw |
| v4l-cx23885-enc.fw      | v4l-cx25840.fw          | vicam                   | vntwusb.fw               |
| vx                      | vxge                    | yam                     | yamaha                   |
===== ifconfig (filtered for eth|wlan|ra|ath|dsl) ================================================================
wlan0     Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#1  
          inet Adresse:192.168.2.100  Bcast:192.168.2.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:25701 errors:0 dropped:0 overruns:0 frame:0
          TX packets:24987 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:19981112 (19.0 Mb)  TX bytes:4480717 (4.2 Mb)
wlan1     Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#2  
          inet Adresse:192.168.2.102  Bcast:192.168.2.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:277 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:51165 (49.9 Kb)  TX bytes:6570 (6.4 Kb)
===== iwconfig ===================================================================================================
lo        no wireless extensions.
eth0      no wireless extensions.
wlan0     IEEE 802.11abgn  ESSID:"§§§§§§§§1"  
          Mode:Managed  Frequency:2.412 GHz  Access Point: ##:##:##:##:##:#3   
          Bit Rate=180 Mb/s   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=70/70  Signal level=-37 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:1320   Missed beacon:0
wlan1     IEEE 802.11bg  ESSID:"§§§§§§§§1"  
          Mode:Managed  Frequency:2.412 GHz  Access Point: ##:##:##:##:##:#3   
          Bit Rate=36 Mb/s   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=64/70  Signal level=-46 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:21   Missed beacon:0
===== cat /etc/sysconfig/network/ifcfg-[earwd]* | grep -v "=''" ==================================================
--- /etc/sysconfig/network/ifcfg-wlan0
BOOTPROTO='dhcp4'
NAME='FRITZ!WLAN USB Stick N'
STARTMODE='hotplug'
USERCONTROL='no'
WIRELESS_AP_SCANMODE='1'
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_DEFAULT_KEY='0'
WIRELESS_ESSID='§§§§§§§§1'
WIRELESS_KEY_LENGTH='@@@@@@'
WIRELESS_MODE='Managed'
WIRELESS_POWER='no'
WIRELESS_WPA_PSK='@@@@@@'
--- /etc/sysconfig/network/ifcfg-wlan1
BOOTPROTO='dhcp4'
NAME='Wireless Adapter'
STARTMODE='hotplug'
USERCONTROL='no'
WIRELESS_AP_SCANMODE='1'
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_DEFAULT_KEY='0'
WIRELESS_ESSID='§§§§§§§§1'
WIRELESS_KEY_LENGTH='@@@@@@'
WIRELESS_MODE='Managed'
WIRELESS_POWER='no'
WIRELESS_WPA_PSK='@@@@@@'
===== iwlist scanning ============================================================================================
                    Channel:1
                    Quality=70/70  Signal level=-38 dBm  
                    Encryption key:on
                    ESSID:"§§§§§§§§1"
                    IE: WPA Version 1
                    IE: IEEE 802.11i/WPA2 Version 1
                    Channel:1
                    Quality=70/70  Signal level=-24 dBm  
                    Encryption key:on
                    ESSID:"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"
                    IE: WPA Version 1
                    Channel:1
                    Quality=22/70  Signal level=-88 dBm  
                    Encryption key:on
                    ESSID:"§§§§§§§§3"
                    IE: WPA Version 1
                    IE: IEEE 802.11i/WPA2 Version 1
                    Channel:5
                    Quality=25/70  Signal level=-85 dBm  
                    Encryption key:on
                    ESSID:"§§§§§§§§4"
                    IE: IEEE 802.11i/WPA2 Version 1
                    Channel:1
                    Quality=67/70  Signal level=-43 dBm  
                    Encryption key:on
                    ESSID:"§§§§§§§§1"
                    IE: WPA Version 1
                    IE: IEEE 802.11i/WPA2 Version 1
===== ndiswrapper -l =============================================================================================
No ndiswrapper module loaded
===== Active processes ===========================================================================================
wpa_supplicant:YES knetworkmanager:NO nm-applet:NO
===== Active WPA processes =======================================================================================
wpa_supplicant -iwlan0 -c/var/run/wpa_supplicant-wlan0.conf -Dnl80211,wext -P/var/run/wpa_supplicant/wlan0.pid -B
wpa_supplicant -iwlan1 -c/var/run/wpa_supplicant-wlan1.conf -Dnl80211 -P/var/run/wpa_supplicant/wlan1.pid -B
===== ===== egrep -i "persistent|networkmanager" /etc/sysconfig/network/config | grep -v "^#|^$" =================
NETWORKMANAGER="no"
===== dhcpcd-test ================================================================================================
wlan0: DHCP server available
wlan1: DHCP server available
===== ping tests =================================================================================================
Ping of 195.135.220.3 OK
Ping of www.suse.de OK
===== cat /etc/resolv | grep -i "nameserver" =====================================================================
nameserver 192.168.2.1
===== cat /etc/hosts =============================================================================================
127.0.0.1       localhost 
192.168.2.1     biberbau biberbau.filia.co
===== route -n | egrep "(eth|ath|ra|wlan|dsl)" ===================================================================
0.0.0.0         192.168.2.1     0.0.0.0         UG    0      0        0 wlan0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 wlan0
192.168.2.0     0.0.0.0         255.255.255.0   U     0      0        0 wlan0
192.168.2.0     0.0.0.0         255.255.255.0   U     0      0        0 wlan1
===== Actual date for bias of following greps ====================================================================
18:11:09 2012-02-29
===== grep -i radio /var/log/messages* | tail -n 5 ===============================================================
/var/log/messages~:Feb 23 21:28:50 biberbau kernel: [ 7430.703886] Registered led device: rtl8187-phy1::radio
/var/log/messages~:Feb 23 21:52:27 biberbau kernel: [   20.377728] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 24 08:25:08 biberbau kernel: [   19.061709] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 24 10:15:20 biberbau kernel: [   18.625678] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 24 15:17:10 biberbau kernel: [   21.090804] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 24 17:56:25 biberbau kernel: [   31.623213] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 25 07:25:07 biberbau kernel: [   22.131749] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 25 09:54:01 biberbau kernel: [   19.514734] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 25 10:32:29 biberbau kernel: [   23.585929] Registered led device: rtl8187-phy0::radio
/var/log/messages~:Feb 25 11:49:16 biberbau kernel: [   19.627719] Registered led device: rtl8187-phy0::radio
===== dmesg | grep -i radio | tail -n 5 ==========================================================================
[15164.609683] Registered led device: rtl8187-phy1::radio
===== tail -n 300 /var/log/messages* | /usr/bin/grep -i firmware | tail -n 10 ====================================
===== egrep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/*persistent-net* ==============
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#1", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#4", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#2", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan1"
===== egrep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*|egrep -v -i '#|backlist' ================
==================================================================================================================
*** NWElizaStates V0.6.5.4.6
IF:wlan0 IM:2 IF:wlan1 IM:2 DI:2 AP:2 FALON:0


Danke schon mal

adda
 
OP
A

adda

Member
Ich habe heute auch "hp-check" ausgeführt. Ergebnis auszugsweise =

Checking for permissions of USB attached printers...

HP Device 0xca02 at 002:002:
Device URI: hp:/usb/Wireless_Adapter?serial=0017089AB341
error: Unsupported model: Wireless_Adapter

Was kann man da machen ?

adda
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben