Heinz-Peter
Guru
Ich habe das Problem das die wlan0 Schnittstelle bringt keine Verbindung zustande.
Warum auch immer wird die wlan0 manchmal nach Suse11.3 Start nicht erkannt und auch nicht geladen dann bekomme ich Verbindung mit meiner wlan1 Schnittstelle.
Wie kann ich eventuell verhindern das Laden der wlan0 Schnittstelle?
Gruß
EDIT: Beide Schnittstellen benutzen das gleiche Modul. Siehe ´Driver: "rt2500usb"´
und hier die collectNWData.txt Script Ausgabe: http://nopaste.info/3e1306a6c1.html
Warum auch immer wird die wlan0 manchmal nach Suse11.3 Start nicht erkannt und auch nicht geladen dann bekomme ich Verbindung mit meiner wlan1 Schnittstelle.
Wie kann ich eventuell verhindern das Laden der wlan0 Schnittstelle?
Gruß
EDIT: Beide Schnittstellen benutzen das gleiche Modul. Siehe ´Driver: "rt2500usb"´
Code:
49: USB 00.0: 0282 WLAN controller
[Created at usb.122]
Unique ID: 2UT6.dg+CvgdQaP0
Parent ID: k4bc.9T1GDCLyFd9
SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3:1.0
SysFS BusID: 1-3:1.0
Hardware Class: network
Model: "ASUSTek 802.11g WLAN Drive"
Hotplug: USB
Vendor: usb 0x0b05 "ASUSTek Computer, Inc."
Device: usb 0x1706 "802.11g WLAN Drive"
Revision: "0.01"
Driver: "rt2500usb"
Driver Modules: "rt2500usb"
Device File: wlan1
Features: WLAN
Speed: 480 Mbps
HW Address: 00:11:d8:dc:18:89
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "usb:v0B05p1706d0001dc00dsc00dp00icFFiscFFipFF"
Driver Info #0:
Driver Status: rt2500usb is active
Driver Activation Cmd: "modprobe rt2500usb"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #44 (Hub)
53: USB 00.0: 0282 WLAN controller
[Created at usb.122]
Unique ID: H8hY.g_9cFk0xIL3
Parent ID: zFuK.4uPzupm_EOA
SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8.1/1-8.1:1.0
SysFS BusID: 1-8.1:1.0
Hardware Class: network
Model: "Ralink 802.11g WiFi"
Hotplug: USB
Vendor: usb 0x148f "Ralink Technology, Corp."
Device: usb 0x2570 "802.11g WiFi"
Revision: "0.01"
Driver: "rt2500usb"
Driver Modules: "rt2500usb"
Device File: wlan0
Features: WLAN
Speed: 480 Mbps
HW Address: 00:11:09:50:13:35
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "usb:v148Fp2570d0001dc00dsc00dp00icFFiscFFipFF"
Driver Info #0:
Driver Status: rt2500usb is active
Driver Activation Cmd: "modprobe rt2500usb"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #50 (Hub)