• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst]Netzwerkkarte meldet NO-CARRIER / Status DOWN

ThomasS

Newbie
Hallo,
als Neuling bei Linux habe ich mir OpenSuse 11.1+KDE über Internet Installation installiert. Die Installation selber lief problemlos, jetzt habe ich allerdings keine Netzwerkverbindung mehr.
Eine Abfrage mit 'ip addr' zeigt für die Netzwerkkarte <NO-CARRIER, BROADCAST.... an, weiter hinten in der Zeile steht ..state DOWN...
Die Netzwerkkarte ist aber definitiv am Netz, wenn ich meine FreeNAS-Live-CD einlege, funktioniert mein NAS auf diesem Rechner einwandfrei.
Woran kann das liegen?
 

spoensche

Moderator
Teammitglied
Überprüfe mal deine Netzwerkkonfiguration.

Führe mal das Script von http://www.linux-tips-and-tricks.de/index.php/collectNWData.sh/collectNWData.html aus und poste mal die Ausgabe.
 
OP
T

ThomasS

Newbie
Hallo,
hier der Inhalt der collectNWData.txt:
Kleine Anmerkung noch: Mein DSL-Router sieht die Adresse 192.168.178.15 des Linux als aktiv. Ich hatte bei meinen Versuchen auch schon mal DHCP statt fester Adresse aktiv, der Router hatte dem PC auch eine Adresse zugeteilt, aber ins Internet kam ich auch nicht. (Router anpingen funktionierte glaube ich auch nicht)

Code:
collectNWData.sh V0.6.1.8-1b (Rev: 1.144)
--- Which type of your network connection should be tested?
--- (1) Wired connection
--- What's the type of networktopology?
--- (2) DSL HW router <---> LinuxClient
--- On which host is the script executed?
--- (1) LinuxClient
!!! CND0180I: The system can't ping external IP address 195.135.220.3
!!! CND0150E: There might be problems with the default gateway definition 192.168.178.1 on interface eth0
!!! CND0310W: Classic network configuration with ifup was detected. Configuration with knetworkmanager is much easier
--- Writing networkconfiguration information into file collectNWData.txt ...
--- 1 errors detected
--- 1 warnings detected
--- Go to http://www.linux-tips-and-tricks.de/CND to get more detailed instructions about the error/warning messages and how to fix the problems
--- If you still don't have success then post the contents of file collectNWData.txt in your favorite Linux forum. For an alternative read http://www.linux-tips-and-tricks.de/CND_UPL
==================================================================================================================
==================================================================================================================
*** uname -a
Linux verleihnix 2.6.27.7-9-pae #1 SMP 2008-12-04 18:10:04 +0100 i686 i686 i386 GNU/Linux
==================================================================================================================
*** cat /etc/*-release
LSB_VERSION="core-2.0-noarch:core-3.2-noarch:core-2.0-ia32:core-3.2-ia32"
openSUSE 11.1 (i586)
VERSION = 11.1
==================================================================================================================
*** cat /etc/resolv | grep -vi "search"
nameserver %%%.%%.%%%.%%1
==================================================================================================================
*** cat /etc/hosts
127.0.0.1       localhost
127.0.0.2       verleihnix.site verleihnix
192.168.178.15  linux linux
192.168.178.15  verleihnix verleihnix
==================================================================================================================
*** cat /etc/HOSTNAME
verleihnix.site
==================================================================================================================
*** route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.178.0   0.0.0.0         255.255.255.0   U     0      0        0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.178.1   0.0.0.0         UG    0      0        0 eth0
==================================================================================================================
*** ifconfig
eth0      Link encap:Ethernet  HWaddr ##:##:##:##:##:#1  
          inet addr:192.168.178.15  Bcast:192.168.178.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:39 errors:103 dropped:0 overruns:0 frame:0
          TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2847 (2.7 Kb)  TX bytes:3727 (3.6 Kb)
          Interrupt:3 Base address:0xd800 
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:96 errors:0 dropped:0 overruns:0 frame:0
          TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:12340 (12.0 Kb)  TX bytes:12340 (12.0 Kb)
==================================================================================================================
*** ping tests
Ping of 195.135.220.3 failed
ping: unknown host www.suse.de
Ping of www.suse.de failed
==================================================================================================================
*** dhcpcd-test
eth0: No DHCP server detected
==================================================================================================================
*** lspci
02:09.0 Ethernet controller [0200]: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31)
==================================================================================================================
*** lsusb
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0ea0:6803 Ours Technology, Inc. OTI-6803 Flash Disk
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
==================================================================================================================
*** hwinfo --netcard; # (filtered)
18: PCI 209.0: 0200 Ethernet controller
  Model: "Davicom 21x4x DEC-Tulip compatible 10/100 Ethernet"
  Vendor: pci 0x1282 "Davicom Semiconductor, Inc."
  Device: pci 0x9102 "21x4x DEC-Tulip compatible 10/100 Ethernet"
  SubVendor: pci 0x4554 
  SubDevice: pci 0x434e 
  Driver: "tulip"
  Driver Modules: "tulip"
  Device File: eth0
  Link detected: no
    Driver Status: dmfe is not active
    Driver Activation Cmd: "modprobe dmfe"
    Driver Status: tulip is active
    Driver Activation Cmd: "modprobe tulip"
==================================================================================================================
*** List of loaded modules
| ac97_bus                | af_packet               | agpgart                 | ata_generic              |
| ata_piix                | binfmt_misc             | cdrom                   | crc_t10dif               |
| dcdbas                  | dm_mod                  | dock                    | edd                      |
| ehci_hcd                | ext3                    | fat                     | floppy                   |
| fuse                    | gameport                | hwmon                   | i2c_core                 |
| i2c_i801                | ide_core                | ide_pci_generic         | intel_agp                |
| iTCO_vendor_support     | iTCO_wdt                | jbd                     | joydev                   |
| libata                  | loop                    | mbcache                 | microcode                |
| nls_cp437               | nls_iso8859_1           | parport                 | parport_pc               |
| pci_hotplug             | pcspkr                  | piix                    | ppdev                    |
| rtc_cmos                | rtc_core                | rtc_lib                 | scsi_mod                 |
| sd_mod                  | sg                      | shpchp                  | snd                      |
| snd_ac97_codec          | snd_ens1371             | snd_mixer_oss           | snd_page_alloc           |
| snd_pcm                 | snd_pcm_oss             | snd_rawmidi             | snd_seq                  |
| snd_seq_device          | snd_seq_midi            | snd_seq_midi_event      | snd_timer                |
| soundcore               | sr_mod                  | thermal_sys             | tulip                    |
| uhci_hcd                | usbcore                 | usb_storage             | vfat                     |
==================================================================================================================
*** cat /etc/sysconfig/network/ifcfg-[earwd]* | egrep -v ".*=''"
==================================================================================================================
*** cat /etc/sysconfig/network/ifcfg-eth0
BOOTPROTO='static'
IPADDR='192.168.178.15/24'
MTU='1500'
NAME='21x4x DEC-Tulip compatible 10/100 Ethernet'
STARTMODE='hotplug'
USERCONTROL='yes'
==================================================================================================================
*** NWEliza states
IF:eth0  IM:1
DI:1 dI:1 NIC:0 cNiC:1:0 NI:0 cNI:0 PNG:1 DR:1 MTU:0 NISS:0 IP6:0 KM:0 WLW: 0
 

Grothesk

Ultimate Guru
Da rangeln zwei Treiber um die Karte. dmfe und tulip.
Ich würde mal wechselweise einen auf die blacklist setzen.
Dazu sieht die /etc/hosts verfummelt aus. Ich würde da mal aufräumen und auf selbstvergebene IPs verzichten. Die Fritzbox kann (mit aktueller Firmware endlich) auch selber die immergleiche IP vergeben, wenn das benötigt werden sollte.
 
OP
T

ThomasS

Newbie
dfme ist schon in der blacklist gewesen. Daraufhin habe ich dfme von der blacklist gelöscht und tulip auf die blacklist gesetzt - leider ohne Erfolg. Auf der Auflistung des collectNWData der geladenen Module tauchte dfme auch nicht auf bzw. war der Status 'nicht aktiv' gemeldet.

Ich habe auch wieder auf DHCP umstellen wollen, jetzt will YAST2 ein Modul smpppd nachinstallieren, mangels Internetverbindung wohl ein klassischer Deadlock. Ich werde wohl doch die Installations-DVD runterladen müssen.
 
OP
T

ThomasS

Newbie
Nachdem ich mir die Installations-DVD heruntergeladen und Linux nochmal komplett neu installiert hatte, war die Situation wieder dieselbe.
Ich habe nun den Vorschlag aufgegriffen und den einen wie den anderen Treiber ausprobiert (tulip und dfme). Dazu habe ich dfme von der Blacklist genommen und in der YAST2->Netzwerkeinstellungen->Netzwerkkarte-Einstellungen bearbeiten->Hardware auf Modulname dfme umgestellt. Und siehe da, kaum macht man es richtig, geht´s.
Danke !!
 
Oben