Diese Website existiert nur weil wir Werbung mit AdSense ausliefern.
Bitte den AdBlocker daher auf dieser Website ausschalten! Danke.

Etch via Debootstrap

Alles rund um die Server (Web-, Mail-, Datenbank-, Datenaustausch-, etc.) die man unter Linux betreiben kann

Moderator: Moderatoren

Antworten
CvH
Newbie
Newbie
Beiträge: 2
Registriert: 13. Sep 2006, 13:53

Etch via Debootstrap

Beitrag von CvH » 7. Mai 2007, 15:36

Hallo, ich habe versucht auf meinem Strato Server Debian Etch mittels Debootstrap zu installieren. (Anleitung gefolgt)

Da ich kein Software Raid haben möchte und mir eine frische Etch installation lieber ist als eine geupdatete sarg->etch (vorallem bei den Strato preinstall).

Soweit hat alles gut geklappt nur kommt jetzt beim start folgende fehlermeldung
Bootdata ok (command line is root=/dev/sda1 ro console=tty0 console=ttyS0,57600 )
Linux version 2.6.18-4-amd64 (Debian 2.6.18.dfsg.1-12etch1) (dannf@debian.org) ( gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Wed Apr 18 12: 02:35 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fffe000 (ACPI data)
BIOS-e820: 000000003fffe000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec03000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI present.
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003fff0000
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003fff0000
ACPI: PM-Timer IO Port: 0x508
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:7 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x02] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 2, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x03] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 3, version 17, address 0xfec02000, GSI 32-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
Built 1 zonelists. Total pages: 257562
Kernel command line: root=/dev/sda1 ro console=tty0 console=ttyS0,57600
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 1995.082 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ 0 size 32 MB
No AGP bridge found
Memory: 1024080k/1048512k available (1930k kernel code, 24044k reserved, 868k da ta, 176k init)
Calibrating delay using timer specific routine.. 3993.09 BogoMIPS (lpj=7986194)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12469278
Detected 12.469 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... OK.
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4467k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Link [LN00] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN01] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN02] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN03] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LN04] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN05] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN06] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN07] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN08] (IRQs 1 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LN09] (IRQs<7>Losing some ticks... checking if CPU fre quency changed.
1 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LN10] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN11] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN12] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN13] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN14] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN15] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN16] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN17] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN18] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN19] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN20] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN21] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN22] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN23] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN24] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN25] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN26] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN27] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN28] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN29] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LN30] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0, disabled .
ACPI: PCI Interrupt Link [LNUS] (IRQs *10)
ACPI: PCI Interrupt Link [LNSA] (IRQs *11)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling IOMMU.
pnp: 00:07: ioport range 0x600-0x61f has been reserved
pnp: 00:07: ioport range 0x520-0x53f has been reserved
pnp: 00:07: ioport range 0x540-0x54f could not be reserved
pnp: 00:07: ioport range 0x544-0x553 could not be reserved
pnp: 00:07: ioport range 0x550-0x55f could not be reserved
pnp: 00:07: ioport range 0x640-0x65f has been reserved
pnp: 00:07: ioport range 0x800-0x80f has been reserved
PCI: Bridge: 0000:01:0d.0
IO window: disabled.
MEM window: fc900000-fc9fffff
PREFETCH window: ff500000-ff5fffff
PCI: Bridge: 0000:00:01.0
IO window: a000-bfff
MEM window: fc900000-fcafffff
PREFETCH window: ff500000-ff5fffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1178543057.280:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 176k freed
Loading, please wait...
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
ACPI: duty_cycle spans bit 4
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not pres ent [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 10, io mem 0xfebfd000
SCSI subsystem initialized
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.1[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 10, io mem 0xfebfc000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.2[A] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:03.2: irq 10, io mem 0xfebfb000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:01:0e.0[A] -> GSI 11 (level, low) -> IRQ 11
ata1: SATA max UDMA/133 cmd 0xFFFFC2000001C000 ctl 0xFFFFC2000001C020 bmdma 0xFF FFC2000001C030 irq 11
ata2: SATA max UDMA/133 cmd 0xFFFFC2000001C100 ctl 0xFFFFC2000001C120 bmdma 0xFF FFC2000001C130 irq 11
ata3: SATA max UDMA/133 cmd 0xFFFFC2000001C200 ctl 0xFFFFC2000001C220 bmdma 0xFF FFC2000001C230 irq 11
ata4: SATA max UDMA/133 cmd 0xFFFFC2000001C300 ctl 0xFFFFC2000001C320 bmdma 0xFF FFC2000001C330 irq 11
scsi0 : sata_svw
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 321672960 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_svw
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7, max UDMA/133, 321672960 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
scsi2 : sata_svw
ata3: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xFFFFC2000001C21C
scsi3 : sata_svw
ata4: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xFFFFC2000001C31C
Vendor: ATA Model: HDT722516DLA380 Rev: V43O
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: HDT722516DLA380 Rev: V43O
Type: Direct-Access ANSI SCSI revision: 05
tg3.c:v3.65 (August 07, 2006)
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 24 (level, low) -> IRQ 169
eth0: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:133MHz:64-bit) 10/100 /1000BaseT Ethernet 00:30:48:56:b6:26
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:02:03.1 -> GSI 25 (level, low) -> IRQ 177
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
eth1: Tigon3 [partno(BCM95704A6) rev 2100 PHY(5704)] (PCIX:133MHz:64-bit) 10/100 /1000BaseT Ethernet 00:30:48:56:b6:27
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
sdb: unknown partition table
sd 1:0:0:0: Attached scsi disk sdb
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Done.
Begin: Running /scripts/local-premount ...
Done.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
mount: Mounting /root/dev on /dev/.static/dev failed: No such file or directory
Done.
mount: Mounting /sys on /root/sys failed: No such file or directory
mount: Mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have /sbin/init


BusyBox v1.1.3 (Debian 1:1.1.3-4) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off



Es sollte irgendetwas falsch eingestellt sein im Bereich hdd nur leider find ich es nicht :(
ich habe 2 160gb HDD´s (dev/sda + dev/sdb) die sollen getrennt arbeiten (sda boot + debian + daten , sdb daten2)

meine Konfiguration:
cfdisk:
Bild

/etc/fstab:
---------------------------------------------------------------------------
# UNCONFIGURED FSTAB FOR BASE SYSTEM
/dev/sda1 /boot ext2 nosuid,nodev 0 2
/dev/sda2 none swap sw 0 0
/dev/sda3 / ext2 defaults 0 0
proc /proc proc defaults 0 0
---------------------------------------------------------------------------


/etc/mtab:
---------------------------------------------------------------------------
proc /proc proc rw 0 0
sysfs /sys sysfs rw 0 0
tmpfs /dev/shm tmpfs rw 0 0
devpts /dev/pts devpts rw,gid=5,mode=620 0 0
/dev/sda1 /boot ext2 rw 0 0
/dev/sda3 / ext2 rw 0 0
/dev/sda1 /boot ext2 rw 0 0
/dev/sda1 /boot ext2 rw 0 0
---------------------------------------------------------------------------
(/dev/sda1 /boot ext2 rw 0 0 fügt es bei jedem neustart hinzu O_o)

/boot/grub/menu.lst:
---------------------------------------------------------------------------
...
title Debian GNU/Linux, kernel 2.6.18-4-amd64
root (hd0,0)
kernel /vmlinuz-2.6.18-4-amd64 root=/dev/sda1 ro console=tty0 console=ttyS0,57600
initrd /initrd.img-2.6.18-4-amd64
savedefault

title Debian GNU/Linux, kernel 2.6.18-4-amd64 (single-user mode)
root (hd0,0)
kernel /vmlinuz-2.6.18-4-amd64 root=/dev/sda1 ro console=tty0 console=ttyS0,57600 single
initrd /initrd.img-2.6.18-4-amd64
savedefault

### END DEBIAN AUTOMAGIC KERNELS LIST

serial --unit=0 --speed=57600
terminal serial
#color cyan/blue white/blue
---------------------------------------------------------------------------


/ dir
---------------------------------------------------------------------------
bin dev initrd lost+found opt sbin tmp vmlinuz
boot etc initrd.img media proc srv usr
debinst home lib mnt root sys var
---------------------------------------------------------------------------


/boot/ dir
---------------------------------------------------------------------------
System.map-2.6.18-4-amd64 grub lost+found
config-2.6.18-4-amd64 initrd.img-2.6.18-4-amd64 vmlinuz-2.6.18-4-amd64
---------------------------------------------------------------------------


kann mir da jemand weiter helfen ?

mfg CvH

Werbung:
Benutzeravatar
Geier0815
Administrator
Administrator
Beiträge: 4272
Registriert: 14. Jun 2004, 09:12

Beitrag von Geier0815 » 7. Mai 2007, 17:37

Schau dir mal grub an: hd und Du willst auf ein sd zugreifen. Könnte da der Fehler liegen? Ich bin kein grub experte, aber das riecht nach einem Fehler.
Wenn Windows die Lösung ist...
kann ich dann bitte das Problem zurück haben?

CvH
Newbie
Newbie
Beiträge: 2
Registriert: 13. Sep 2006, 13:53

Beitrag von CvH » 7. Mai 2007, 20:32

root (hd0,0) meinst du bestimmt, aber das ist richtig da habe ich auch erst gestutzt, aber laut den ganzen faq´s stimmt das :/

bin irgendwie ratlos :(

Wastl
Member
Member
Beiträge: 51
Registriert: 14. Jun 2004, 16:18

Beitrag von Wastl » 29. Jun 2007, 17:04

ja das ist richtig. Grub unterscheidet nicht zwischen IDE,SCSI,SATA oder sonstwas. Grub nummeriert die Platten nach der Reihenfolge die das Bios vorgibt. Somit gibt es da nur hdx,x :)

Was mir auffält ist das er sysfs und devfs auf /root/sys bzw dev mounten will was es natürlich nicht gibt! Da ist irgendwas verkehrt in der confix von dem Zeug denke ich. Und ohne sysfs und devfs kann er kein rootfs mounten bzw findet er /sbin/init nicht weil er ja nichts mounten kann weil die blockdevices nicht existierten...

lg
wastl

Antworten

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 1 Gast